IPS 7.0 to the factory default?

Hello
How to reset the IPS 7.0 to the factory default?
Thanks

Are you getting this message?
sensor(config)# recover application-partition
Warning: Executing this command will stop all applications and re-image the node to
version 6.2(1)E3. All configuration changes except for network settings will be reset to
default.
Continue with recovery? []:
The application partition is reimaged using the image stored on the recovery partition.
You must now initialize the sensor with the setup command.The IP address, netmask, access lists,
time zone, and offset are saved and applied to the reimaged application partition.
You can always save your image and then uploaded to the sensor again.
Is this what you're looking for?
Federico.

Similar Messages

How to reset the factory defaults for Adobe Photoshop CS4? [was:need assistance]

How to reset the factory defaults for Adobe Photoshop, CS4. My 'image size' box is not quite right. Thank you.

How to delete/reset Photoshop preferences
Preference file functions, names, locations | Photoshop CS4
To reset within the Image Size dialog press Alt (Option on Mac) and click Reset.

Hard drive configuration is not set to the factory default

When I go into Acer Recovery Management to try to create a factory default backup I get a pop up that says Hard Drive configuration is not set to the factory default - back up aborted. How do I get my hard drive set back to factory default?

Create recovery backup or recovery media and resetting to default are 2 different things. you can create the recovery backup even without resetting to factory default; you just need to start Acer erecovery and follow instructions. it will copy the recovery partition to DVDs or USB flash media.if Acer erecovery is not working and you have Windows 8.x, you can follow this guide:http://windows.microsoft.com/en-us/windows-8/create-usb-recovery-drive about resetting to factory default, the easiest way is to press ALT+F10 at boot and then follow onscreen instructions.

Need help accessing the factory default restore disk - Ideapad b5609

I am working on a friends PC. It will not start up in normal mode but will start in safe mode. This PC has Windows 7 64 bit installed.
I don't know whjat he did to this except I used Malwarebytes to remove some malware. After I removed the malware, the PC would not boot in safe mode, but would get stuck at classpnp.sys. I searched for a solution for this and the only thing I could get to work was renaming classpnp.sys to classpnp.old. This allowed the PC to boot in safe mode again but this needs to get fixed.
What I wanted to do was access the factory default restore disk, back it up to USB ( No dvd's) if possible and reinstall a fresh copy of the system. - But I don't even know if this laptop has a factory restore disk, Is there one?
The PC owner says he didn't get a dvd when he bought the PC. This person was born without arms and is not too PC literate. He uses the PC for e-mail and going to porn sites. It's possible he did have a dvd for the PC if it came with one but he just doesn't remember or even knew what it is.
I do see a Backup and Repair app in the start menu / Maintenence folder but It doesn't start from safe mode. One Key Recovery doesn't work either.. I don't know what it does but I was going to look at it to see if it will help fix the PC.
I tried a windows system recovery disk, and it says it cannot fix the problem. My friend told me this PC is over a year old so i assume it's out of warrenty.
Please help, Thank you.
Moderator Note; similar threads merged

I've already removed the malware with malwarebytes and double checked this with the offline version of Defender. The PC is over a year old.. the owner tells me it's not in warrenty. I didn't want to mess up the hidden recovery partition so i installed a fresh copy of windows 7 to C drive. Since I can now boot into C i will try to install and use OneKey recovery to access and reinstall from the hidden partition.
I understand there is an Enginers version of Onekey Recovery I may have to get if i have problems - it's the version of OKR that the OEM's use to set up the partition in the first place.. from my info anyway..
This is the second time tryiong to fix it from a fresh install on C drive. The first time had a Windows.old folder I wanted to try to reinstall stuff from, but on trying to back that up to a external hard drive via USB, the system crashed and said missing master boot record. A StartUp Repair disk ran 6 times could not fix the problem ( same disk I used to install.. told me it didn't find any problems !
Other odd behavior.. when i was copying the windows.old folder, it didn't tell me i had so many files to go.. always sais it had 0 files left to transfer.
I couldn't get the sound drivers to work even after downloading the right ones from lenovo. I even let device manager try to reinstall the drivers from the Realtek folder in the windows.old folder - those should have worked - and the pc told me that the drivers matches and were up to date - however, the error i get told me there is a problem with the drivers and installation would fail when i tried to install from the downloaded exe.
I have been fixing my own systems for over 20 years, i have never seen a system as screwy as this with a fresh install.

I have an iPad that was setup on a laptop that has been reimaged. The iPad then had a password put on it and my kid doesn't rememer the password. Since I don't have the original laptop with iTunes installed I cannot reset the iPad to the factory default

I have an iPad that was setup on a laptop that has been reimaged. The iPad then had a password put on it and my kid who doesn't rememer the password. Since I don't have the original laptop with iTunes installed I cannot reset the iPad to the factory default. Any suggestions on how to reset to the iPad?
Thank you

Try recovery mode. I think this should work. You can read the instructions here.
http://support.apple.com/kb/ht4097

T510 what is the factory default Power Plan

I have a Lenovo T510.
In ThinkVantage there are various Power Plans...eg Energy Saver, Timers Off, Power Source Optimized, Maximum Performance, Maximum Battery Life,
Can someone advise me which Power Plan Lenovo sets it to when it is brand new from the factory.
Thank you

Hi Alex 1945:
Okay, I'm typing this on my T510 (bought in December 2010). Lenovo repair center re-imaged my drive and I lost the Energy Saver Profile, which you have. Here are all the power plan profiles that are available on my T510
1. Thinkpad Default
2. Power Source Optimized
3. Timers Off (Presentation)
4. Maximum Battery Life
5. Maximum Performance
6. Video Playback
At least when I got my T510 brand new (pre re-imaging), Energy Saver was selected. Wish I could get that profile back. It set all the options at two green dots. I really got a very long battery life using that profile. Currently using Power Source Optimized, which does well but doesn't get me the battery life of the Energy Saver (although the difference is small).
CHL
T520 Core i5-2540M (2.60GZH) - 500GB SSD - 8.0GB - Blu-Ray - FHD

I tried to reset my nano to the factory default and it says that I only have 1.7 gb

When I tried to sync my ipod to itunes it keeps giving me an error message and then I tried to reset it back to the factory, it says I have 5.5 gb used and 1.7gb left.

Conatct AppleCare Account Security. Contact numbers here:
http://support.apple.com/kb/HT5699?viewlocale=en_US

How do I retrieve the factory default application

not sure how, but one of the default factory app - the Notes was gone from my iPhone 4s, how do I retrieve/restore it?

Can't be deleted or restricted. Look on every page & in every folder...if you have folders. Still don't see it? Then: Settings>General>Reset>Reset Home Screen Layout...see if you see it now.

What are the factory default ringtones on an iphone

I want to reset my ringtones for text and mail back to when the phone was new. I do not remember what they are. I believe text is tri-tone.

IOS 7 default:
Ringtone > Opening
Text Tone > Note
New Voicemail > Tri-tone
New Mail > Ding
Send mail > Swoosh

Can I delete the files in ~/Library/Preferences and have all preferences reset to factory default?

I have this folder inside my /Library folder called Preferences. I was wondering if I could delete all of the files inside this folder and have all of my preferences reset to the factory default?

First, why would you want to do this? I ask because all of the applications installed also have preference files. Some of the preference files store things like serial numbers. Some programs that use plugins that use serial numbers also store the serial numbers in the host program's preference file. RapidWeaver is an example of this.
So, If you deleted all of the files in your preference folder, you could have some major headaches for a while afterward.
If you are curious, there is a program called AppleJack that only runs in Single User mode. It can check preference files for you. There are several others available that cost money. AppleJack is a free open source application.
Hope this helps,
Craig

Error message: itunes-restore phone to factory default on iphone 3 "we're sorry, we are unable to continue with your activation at this time".

Attempting to restore Iphone 3 to factory deafalut, to finish "unlocking" the Iphone 5.
Moving the phone from one cellular carrier to another (in this case Rogers to Bell in Canada).
Rogers "unlocked" the phone on their end for $50.00, sent an email to Apple requesting serial # to be released from their network, and to provide "unlocked" status.
Next step was to restore phone to "factory default" in I tunes, and wait for phone to reset and show "unlocked" status.
Upon phone resetting in Itunes, after the "factory default", received the following error message"
"we are sorry, we are unable to unable to continue with activation at this time Please try again, or contact customer service".
I contacted Apple customer service whom confirmed that the phone is showing as "unlocked" in their system.
New carrier that I am attempting to hook phone up states that the phone is still locked.
What is the solution or workaround?

Hello mzpartia,
I found an article from Apple that specifically outlines how to try and troubleshoot this issue. It's called iPhone: Troubleshooting activation issues found here: http://support.apple.com/kb/ts3424.
Resolution
Perform the following steps if you receive one of the messages above:
Restart the iPhone.
Try another means of reaching the activation server and attempt to activate.
Try connecting to Wi-Fi if you're unable to activate using a cellular data connection.
Try connecting to iTunes if you're unable to activate using Wi-Fi.
Restore the iPhone.
If you receive an alert message when you attempt to activate your iPhone, try to place the iPhone in recovery mode and perform a restore. If you're still unable to complete the setup assistant due to an activation error, contact Applefor assistance.
Take care,
Sterling

Resetting to factory default?

I have seriously messed up some settings in my server, I'd like to reset windows server to the factory default, I am using windows server 2008... I would just put the 2012 trial inside of it, but I cant get it to work, So I am going to stick with my 2008
for now. What I am asking is how do I reset it to the default?

Hello,
there is no way to go to factory defaults instead of a fresh install.
With Windows Server 2012 R2 you are able to do it
https://technet.microsoft.com/en-us/library/jj593197.aspx
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://blogs.msmvps.com/MWeber
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.
Twitter:

Hard drive configuration is not set to factory default. Refurbished Acer Iconia W3-810

This tablet was purchased refurbished. As soon as I got it, I went to create my backup and message is "Hard drive configuration is not set to the factory default. Backup aborted. I had already sent it in once to the seller for repair services and it was sent back not repaired. They now say I can send it in again but seems a waste of time. I called Acer and they said I would need to purchase the recovery disk which should have already been provided to me. It does have a valid SNID number. I checked.   If there is anyone else who came up against this problem, I would love to know what you did to resolve it. Second problem. Large font had been created where is overscans the entire page so reading the Control Panel is impossible. The warranty dept created a new user account with new settings as they were unable to fix the font problem so they ignored it. This is another reason I wanted to do a factory reset. Hoping Acer will be kind enough to just send me the disk.   I've learned alot about refurbished products. Never again.

Hard drive configuration is not set to factory default (I had this problem but mine was caused by some third party partitioning software easeus. I am not pretty entirely sure what was your cause for the error, but I believe this workaround can be useful, even to some of the users)  I learnt a tough lesson and I am now careful on what third party soft wares one must use especially for partitioning related events using windows 8 GPT structure. This article specifically relates to windows 8 (which I was using) although similar steps may work as well in windows 7 Points note:Most newer windows devices now use the GPT partitioning system compared to the traditional MBR system.It can be very difficult to reinstall windows on a partition with GPT format.One must be careful on what 3rd party portioning tools they use. It is not recommend to use some 3rd party tools to resize partitions as these may mess the hard drive configuration in such a way that it will be very difficult to restore to factory settings (especially for devices pre-loaded with OEM-Windows 8)It is recommended to use the in-built Disk management utility to shrink/resize partitions.First and foremost, it is recommended to use system file scanner to check any files that may be corrupted (and most of these are normally fixed by sfc)Press Windows key + X, select ‘Command prompt (Admin)’. Enter the following command “sfc /scannow” (without quotes) and the system will start scanning the system. Wait until it finishes.Now we will proceed to the main fix; here are the set of steps I performed,Run CMD (Admin)Type diskpartType list diskDisk 0 Online 465 GB 19 GB * (an example of how the disk will present)
Disk 1 Online 22 GB 0 B * Select diskDISKPART> select disk 0 list partitionDISKPART> list partition (Note you see recovery partitions flagged as OEM) So what we do is to set the id according to the GUID (Global Unique Identifier) system.Selected every partition with a OEM typeI changed their ID's to DE94BBA4-06D1-4D40-A16A-BFD50179D6AC (see below)Partition 1 OEM 1000 MB 1024 KB
Partition 2 System 260 MB 1001 MB
Partition 3 Reserved 128 MB 1261 MB
Partition 4 Primary 224 GB 1389 MB
Partition 5 OEM 350 MB 226 GB
Partition 6 Unknown 3913 MB 226 GB
Partition 7 Primary 200 GB 230 GB
Partition 8 Unknown 7813 MB 430 GB
Partition 9 OEM 7948 MB 458 GBDISKPART> select part 1Partition 1 is now the selected partition.DISKPART> set id = "de94bba4-06d1-4d40-a16a-bfd50179d6ac"DiskPart successfully set the partition ID.DISKPART> select part 5Partition 5 is now the selected partition.DISKPART> set id = "de94bba4-06d1-4d40-a16a-bfd50179d6ac"DiskPart successfully set the partition ID.DISKPART> select part 9Partition 9 is now the selected partition.DISKPART> set id = "de94bba4-06d1-4d40-a16a-bfd50179d6ac"DiskPart successfully set the partition ID.  Here is a screenshot (please note this is not a screenshot I made, I downloaded it online and I give thanks to the uploader) is just for education purposes. The issue should be solved. Now you can try system refresh/reinstall to factory settings (or create a recovery media)*In my case and others I researched on internet, it turns EASEUS partition master was the culprit, please don’t use that software if you don’t know what you are doing. (With all respect to EASEUS) I think this tool is still not configured well to work with the GPT partition format.

The factory profile for the display could not be found.

Whenever I try to color calibrate my Mid 2010 iMac I get the error message "The factory profile for the display could not be found". When you look at the profile settings for the display a color sync profile is set, but the setting for the factory profile is blank. I know where the color sync profiles are stored but it seems to me that the display has lost the setting to the factory profile. Can anyone tell me what the default factory profile setting should be? and how do you restore the setting? (note: I seem to have all the ICC files, it's the default factory setting itself that is missing)

There seems to be a lot of posts about this issue dotted around the net with no-one able to come up with a solution. So I found a solution myself! =P
1) Download a copy of Plistedit Pro. It's shareware, so donate!
2) Edit /Library/Preferences/.GlobalPreferences.plist (you will need to create a copy of the file, edit the copy and then copy back)
Using the plist editor find the coloursync entry for your device and simply edit the factory default entry to point to a valid colorsync profile file (.icc).
I can now colour calibrate my iMac again. Phew!!!

Setting aironet 1100 to factory default

I am trying to reset an aironet 1100 back to factory default. The only button on the bottom of the unit that I can see is one that says mode on it. Is their somewhere else where the factory default can be reset at. Thanks

Hello,
This should work for your situation:
Reset the APCisco IOS Software
Complete the steps in this section in order to reset Cisco IOS Software-based APs.
Note: Cisco IOS Software-based APs have a default configuration that includes a username and password combination. Both the username and password are "Cisco", which is case-sensitive. After you reset to factory defaults, be prepared to give "Cisco" as both the username and password when you are prompted by either the GUI or the command-line interface (CLI).
If the privileged command prompt ap# is available in the CLI, the write erase command and the reload command erase the startup configuration and reset the unit.
If the GUI is available, choose System Software > System Configuration. Press the Reset to Defaults button.
If neither the GUI nor the CLI is available with sufficient privileges, complete these instructions in order to use the Mode button:
Disconnect power from the AP.
Disconnect the power jack for external power or the Ethernet cable for inline power.
Press and hold the MODE button while you reconnect power to the AP.
Hold the MODE button until the Status LED turns amber, and then release the button.
The Status LED turns amber in approximately 1 to 2 seconds.
After the AP reboots, reconfigure the AP and use the web browser interface, the Telnet interface, or Cisco IOS Software commands.
Note: The AP is configured with the factory default values that include:
The IP address, which is set to receive an IP address with DHCP
The default username and password, "Cisco"
Here is the link to the actual doc:
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_password_recovery09186a00800949d0.shtml#resios
Hope this helps!
Rob
Please remember to rate helpful posts........

IPS 7.0 to the factory default?

Similar Messages

Maybe you are looking for