IPsec through link with low percentage of errors

Hello
I need help with IPsec configuration.
On one side of IPsec tunnel is ASA 5505 and on other side of IPsec is C1841 sec K9
On ASA side I have optical link which is error free and on other side of IP sec I have wireless point-to-point link which sometimes have error on wireless part.
When error occurs on radio link, IPsec tunnel stop forwarding traffic.
When I do show crypto isakmp sa on C1841 I see that IPsec is created, but traffic is not forwarding.
Only clear crypto sa comand on C1841 help me to rebuilt the tunnel.
Did anybody have a similar issue with IPsec on error link between router and ASA and how they solved them ?
Best Regards, Slobodan

Well I have no idea why but yesterday afternoon and all this morning everything has been working just fine... There must have been something with which HDD the footage was on or something. I was messing aroudn with trying to stitch some AVCHD clips together and I had clips all over the place. After I kind of cleaned things up it was working just fine. I guess as usual it was user error...
Phil

Similar Messages

IPSec remote VPN with VPN client giving error

Hi ,
ASA 5505 current configuration is : (setup using ASDM)
esult of the command: "show running-config"
: Saved
ASA Version 8.2(5)
hostname TEST
enable password ___________ encrypted
passwd __________ encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
ftp mode passive
access-list sap_vpn_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip 192.168.1.0 255.255.255.0 192.168.10.0 255.255.255.224
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool test_pool 192.168.10.0-192.168.10.20 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication http console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
dhcpd address 192.168.1.5-192.168.1.132 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy sap_vpn internal
group-policy sap_vpn attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value sap_vpn_splitTunnelAcl
username test password ____________ encrypted privilege 0
username test attributes
vpn-group-policy sap_vpn
username TEST password ________________ encrypted privilege 15
tunnel-group sap_vpn type remote-access
tunnel-group sap_vpn general-attributes
address-pool test_pool
default-group-policy sap_vpn
tunnel-group sap_vpn ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:b67cdffbb9567f754052e72f69ef95f1
: end
I am using VPN client with host IP 192.168.2.20 and group authentication with username:sap_vpn and preshared key as password but could not connect to vpn and getting attached error message.
ASA set up with ASDM initial wizard: inside interface (VLAN1) IP 192.168.1.1 and outside (VLAN2) IP 192.168.2.20 assigned using DHCP. I am using outside interface IP 192.168.2.20 for HOST IP in VPN client for remote connection??? is it right??
please advise for this.

Hi,
current configuration for ASA 5505 for IPSec remote VPN as below:
ASA Version 8.2(5)
hostname _________
domain-name ________
enable password ___________ encrypted
passwd _________ encrypted
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.0.7 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address ______________(public IP)
ftp mode passive
dns server-group DefaultDNS
domain-name ________
access-list inside_nat0_outbound extended permit ip any 172.16.0.0 255.255.224.0
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool test_pool 172.16.10.0-172.16.16.20 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication http console LOCAL
http server enable
http 192.168.0.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcp-client client-id interface outside
dhcpd auto_config outside
dhcpd address 192.168.0.11-192.168.0.138 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy dyt_vpn internal
group-policy dyt_vpn attributes
vpn-tunnel-protocol IPSec
default-domain value _______
username test password _________ encrypted privilege 0
username test attributes
vpn-group-policy dyt_vpn
username ________ password ______________encrypted privilege 15
tunnel-group dyt_vpn type remote-access
tunnel-group dyt_vpn general-attributes
address-pool test_pool
default-group-policy dyt_vpn
tunnel-group dyt_vpn ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:eb0f7a5c2385b7400e9b9432fb2df9d1
: end
when I am assigning PUblic IP to outisde interface of ASA, it is showing outside interface down.
can anybody please help me for that.
Thanks,
Sap

Error while testing Adapter through RWB with payload

Hi all,
While testing Adapter engine through RWB with payload, i get the below error
Error while sending message: com.sap.aii.af.ra.ms.api.ConfigException: ConfigException in XI protocol handler. Failed to determine a receiver agreement for the given message. Root cause: com.sap.aii.af.service.cpa.impl.exception.CPALookupException: Couldn't retrieve outbound binding for the given P/S/A values: FP=;TP=;FS=ec6clnt001;TS=com_avaya_java_bs;AN=StartNotification_MI_sync;ANS=http://www.tcs.com/sap/xi/AVAYAPoC;"
Can any body please suggest the possible reason and solution for the same.
Regrads,
Kulwant

Hi
verify the receiver agreement and also check it out whether receiver message interface is configured properly or not?
or
open ID and goto tools tab in that click on
test configuration by providing your Business service and interface details along with the payload it displays the error message.
regards
Suryanarayana

Getting ORA-12518 error with DG4ODBC for link with SQL Server

Hi all,
We have recently upgraded a test box to 11g2 on a 64bit windows platform and now when setting up our database links with our sql servers we are recieving an 'ORA-12518' error.
listener.ora
LISTENERPCIS =
(DESCRIPTION =
(ADDRESS = (PROTOCOL = TCP)(HOST = WILTS-ORCL4)(PORT = 1522))
SID_LIST_LISTENERPCIS =
(SID_LIST =
(SID_DESC =
(PROGRAM = dg4odbc)
(SID_NAME = PCIS)
(ORACLE_HOME = c:\oracle\product\11.2.0\db_1)
tnsnames.ora
PCIS =
(DESCRIPTION =
(ADDRESS_LIST =
(ADDRESS = (PROTOCOL = TCP)(HOST = WILTS-ORCL4)(PORT = 1522))
(CONNECT_DATA =
(SID = PCIS)
(HS = OK)
Any help appericated
Cheers
David

C:\Users\administrator.ADMIN>tnsping pcis
TNS Ping Utility for 64-bit Windows: Version 11.2.0.1.0 - Production on 24-JUN-2
010 20:55:29
Copyright (c) 1997, 2010, Oracle. All rights reserved.
Used parameter files:
C:\ORACLE\PRODUCT\11.2.0\DBhome_1\network\admin\sqlnet.ora
Used TNSNAMES adapter to resolve the alias
Attempting to contact (DESCRIPTION = (ADDRESS = (PROTOCOL = TCP)(HOST = localhos
t)(PORT = 1522)) (CONNECT_DATA = (SID = PCIS)) (HS = OK))
OK (0 msec)
C:\Users\administrator.ADMIN>lsnrctl status LISTENERPCIS
LSNRCTL for 64-bit Windows: Version 11.2.0.1.0 - Production on 24-JUN-2010 20:55
:47
Copyright (c) 1991, 2010, Oracle. All rights reserved.
Connecting to (DESCRIPTION=(ADDRESS=(PROTOCOL=TCP)(HOST=localhost)(PORT=1522)))
STATUS of the LISTENER
Alias listenerpcis
Version TNSLSNR for 64-bit Windows: Version 11.2.0.1.0 - Produ
ction
Start Date 24-JUN-2010 20:55:17
Uptime 0 days 0 hr. 0 min. 30 sec
Trace Level admin
Security ON: Local OS Authentication
SNMP OFF
Listener Parameter File C:\ORACLE\PRODUCT\11.2.0\DBhome_1\network\admin\listen
er.ora
Listener Log File c:\oracle\product\11.2.0\diag\tnslsnr\WILTS-ORCL4\listenerpcis\alert\log.xml
Listener Trace File c:\oracle\product\11.2.0\diag\tnslsnr\WILTS-ORCL4\listenerpcis\trace\ora_12216_2424.trc
Listening Endpoints Summary...
(DESCRIPTION=(ADDRESS=(PROTOCOL=tcp)(HOST=127.0.0.1)(PORT=1522)))
(DESCRIPTION=(ADDRESS=(PROTOCOL=ipc)(PIPENAME=\\.\pipe\PNPKEYipc)))
Services Summary...
Service "PCIS" has 1 instance(s).
Instance "PCIS", status UNKNOWN, has 1 handler(s) for this service...
The command completed successfully
C:\Users\administrator.ADMIN>dg4odbc
Oracle Corporation --- THURSDAY JUN 24 2010 20:55:54.257
Heterogeneous Agent Release 11.2.0.1.0 - 64bit Production Built with
Oracle Database Gateway for ODBC
C:\Users\administrator.ADMIN>

Hard drive says I have more than 300 GB available with a 500 gb capacity. Yet I get "Low Disk Space" error messages when I do anything.

Hard drive says I have more than 300 GB available with a 500 gb capacity. Yet I get "Low Disk Space" error messages when I do anything.
Attempted solutions:
-I created a new User Account and I can download large files with no issues.
-I ran "Repair Disk Permissions" but still get warnings.
Google Drive Warning:
Spotify Warning:
But on my other user account I can use spotify and download large files, etc.

Back up all data. Don't continue unless you're sure you can restore from a backup, even if you're unable to log in.
This procedure will unlock all your user files (not system files) and reset their ownership and access-control lists to the default. If you've set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it.
Step 1
If you have more than one user account, and the one in question is not an administrator account, then temporarily promote it to administrator status in the Users & Groups preference pane. To do that, unlock the preference pane using the credentials of an administrator, check the box marked Allow user to administer this computer, then reboot. You can demote the problem account back to standard status when this step has been completed.
Enter the following command in the Terminal window in the same way as before (triple-click, copy, and paste):
{ sudo chflags -R nouchg,nouappnd ~ $TMPDIR.. ; sudo chown -R $UID:staff ~ $_ ; sudo chmod -R u+rwX ~ $_ ; chmod -R -N ~ $_ ; } 2> /dev/null
This time you'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
The command will take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear, then quit Terminal.
Step 2 (optional)
Take this step only if you have trouble with Step 1 or if it doesn't solve the problem.
Boot into Recovery. When the OS X Utilities screen appears, select
Utilities ▹ Terminal
from the menu bar. A Terminal window will open.
In the Terminal window, type this:
res
Press the tab key. The partial command you typed will automatically be completed to this:
resetpassword
Press return. A Reset Password window will open. You’re not going to reset a password.
Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
Select your username from the menu labeled Select the user account if not already selected.
Under Reset Home Directory Permissions and ACLs, click the Reset button.
Select
 ▹ Restart
from the menu bar.

IPad Air crashes with low memory error in Google Translate Web Site

My new iPad Air crashes with low memory error every time I try to use my Phrasebook in Google Translate Web site. This is rather disapointing considering that my old Nexus 10, that iPad Air is supposed to replace, works flawlessly in Google Translate Web site. Perhaps this has to do with the rather limited RAM (1GB) that iPad Air is equippoed with.
I would appreciate any recommendation, Thanks in advance.

See this topic in
https://discussions.apple.com/message/24758170?ac_cid=tw123456#24758170
And other threads
Good luck.

Runtime error in linking with static variables....

Hi,
I am building a shared library which includes a compiled object generated from a class containing the static variables only and also I have another version of same class with same & some new static variables in it and using that to generate another shared library. Now when I tried to run a program
which links with both the library it core dumps when it tries to return from the program i.e when it finishes.
Can someone please help me explain why my program is behaving like that?? Can duplicate inculsion of static variables in different scope can cause problem ?? How can this be avoided ?
Also please be advised that the class with static variables gets generated at the compile time using a script which uses a DTD whose version (specification) can be different in both the libraries therefore I can't just seperate the common stuff into one class and specific into another.
Thanks.
Rajeev.

Not to worry...found the answer in another post. Seems like patches need to applied to the OS.

Exchange Friend Links with ShenTop - One-Stop Chinese goods Procurement Service

Exchange Friend Links with ShenTop - One-Stop Chinese goods Procurement Service
Home page: The applicant must meet the requirements below:
1. PR value of 3 or more;
2. Alexa ranking within 100,000;
3. More than 1,000 collected by Google;
Our Link Address:
[url]http://www.shentop.net[/url]
1. PR value of 3 or more;
2. More than 30,000 collected by Google;
3. Text Link: Hotel Supplies;
Contact: Aries Liu
Skype:Md.shentop
Email:[email protected]
Welcome [url]http://shentop.net[/url] - One-Stop Chinese goods Procurement Service ; Your satisfaction is our utmost priority. By offering you China's largest one stop shopping platform for commercial equipment, we hope we can satisfy all your needs, such as corporate culture exchange, entrepenuerial experiences and insights, hotel merchandise, lobby equipment commercial electronics, wine cellar inquiries, lamp, light, ceram, Please feel free to google Shentop.net
If you want to be the next entrepreneurs,make you business more stronger in future,lower cost is necessary ,google shentop.net,you will find it.
[URL="http://shentop.net"][img]http://www.shentop.net/uploadfile/content/201110/20111010120946_26529.gif[/img][/URL][/COLOR]

@ adobe-admin (J.C.?):
Thanks for fixing the "backslash" error. Accuracy is important, and doubly so when presented as an F.A.Q.
The sad thing is how prevalent the usage of "backslash" is when a plain old slash is meant (generally, the "forward" attribute is assumed and unneeded), and by people who should know better. It's a direct result of people knowing just barely enough about the Windows file path naming protocols, and then applying the only terminology they're familiar with incorrectly to URLs.
I went about 10 rounds—TWICE!—with a labyrinthian succession of people at the Discovery & History cable TV networks because they were saying "backslash" in voice overs whenever their commercials promoted their websites. It took some doing, but I finally got in touch with somebody who was savvy enough to recognize that it was a rookie mistake made by a clueless marketing copywriter. The voice over person just read the copy they were given, oblivious to the difference. It amazes me that it wasn't caught by somebody early in the recording/production process and rectified.
They then had it correct for about a year, until new commercials started popping up with the same error. Unfortunately, the person I had talked to previously no longer worked for the History channel and I had to go through the process of finding someone who understood all over again.
Yeah, you can call me a nitpicker with nothing better to do.
But I've earned that dang badge, and I wear it proudly!

Facility low rx power error

I have a Cisco ONS router that is getting a "Facility low rx power" error on an OC192 card.
Anyone know what this means or how to troubleshoot? I can't seem to find much in the documentation.
thanks

I assume this is on ONS15454 MSPP (SDH), I've not seen this particular alarm before but it would indicate that the RX Optical Power is below the minimum threshold, this may be due to a failing laser in the TX Device or fibre plant degredation.
I am not aware that the MSPP variant has any remote monitoring facility to check the opical power levels like you can with the MSTP variant so I think you may have to disconnect the fibre and check with a light meter, I would start at the TX device and then follow it through to the RX device, as I said it may be that the laser is failing in which case it may be a good idea to have a spare card handy to replace the card while you have the service outage.
If you need to know the Optical Specs for the particular STM64 (OC-192) card you are using then while in card view click the Maintenance Tab then the Info Tab at the side, its not available for all cards but it does for the cards we have in one of our networks, failing that specifications for all cards can be found in Appendix A of the Reference Manual, this is a link to the Reference Manual page, just select right one for the software you are running:
http://www.cisco.com/en/US/partner/products/hw/optical/ps2006/prod_technical_reference_list.html
Hope this helps, if not post up again and someone may be able to help further.

How to update all condition records at a time with some percentage or some

Dear Sir,
In PRD system we have more than 600 condtion records.
Noe desiel hikes happend, due to that client want to update all condition records(600) at a time with required percentage or required value.
How to update all records at a time
With regards
Lakshmikanth

Hi,
Through BDC or LSMW first you have to do the recording for particular transaction code and then base on that u have to prepare the flat file to upload the file for the same.
For BDC programing you have to take the help of ABAP progmer but LSMW you can also do.
For more information about LSMW plz go to following link :
[LSMW |http://www.slideshare.net/arun_bala1/sap-sd-lsmw-legacy-system-migration-workbench/]
[Step-by-Step Guide for using LSMW|www.scmexpertonline.com/downloads/SCM_LSMW_StepsOnWeb.doc ]
BDC
[BDC Call Transaction|http://www.sapdevelopment.co.uk/bdc/bdc_ctcode.htm]
[BDC Recording|http://www.sapdevelopment.co.uk/bdc/bdc_recording.htm]
But it would be better for you to please contact to your ABAPer for BDC programming.
Cheers...

Performance of Top Link with clustering

Hi,
We are planning to use Top Link with a J2EE app that will reside on Oracle 9i app server. We are also planning to use clustering of app server. So we will need to configure Top Link ServerSessions accordingly (isnt it?).
Do you think the performance of TopLink will be reduced badly if used in this fashion, since the server sessions have to talk to each other continuously !
Thanks,
Krishna

Krishna,
The Cache-Sync feature of TopLink is an excellent way to minimize stale data. The messaging and change-set propagation does not come without a cost though. Typically we try to recommend this for customers with a high percentage of reads. In these cases it is more beneficial to keep the cache and avoid trips to the database.
There is no magic formula for when to use cache-sync. The messaging cost/efficiency is dependent on the mechanism (point to point over RMI/CORBA/IIOP or JMS), the size of the change sets or complexity of transaction, number of servers in the cluster, etc.
What is important to understand though is that cache-sync is just one way to minimize stale cache. It does not ensure you won't have stale data. For this you must configure a locking strategy and adjust your cache relative to the expected life-span you need on cached objects.
For a system like your I would recommend starting out without cache-sync. Use optimistic locking on all classes and use a weak cache for all classes that have a high occurrence of writes. For the rest I would recommend a Full cache on static/reference data and a soft-weak cache on those that fall in between. The size of the soft-weak cache will determine the number of objects potentially held (LRU) beyond their use.
With these settings you should be able to monitor and account for changes made to stale objects through OptimisticLockExceptions. If you find specific use-cases that are prone to failure you could force the refresh on the query at the start of the UnitOfWork (TX).
This approach will give you a system that ensures data integrity. Then you can experiment with scaling to multiple servers with or without cache-sync and monitor the load vs failures for your test environment.
I hope this helps,
Doug

When I try to install my Brother MFC-8810DW printer through a wireless network I get error:-30886

When I try to install my Brother MFC-8810DW printer through a wireless network I get error:-30886. The computer recognizes the printer, and asks me to identify the software, but I get the same error message repeatedly.

That file might have moved to a different location on the server. I think you'll need to check with RefWorks support or your local IT department on why the install page links do not work.

Having trouble with itunes update. Error with itunes64.msi. Windows 8.1 64 bit. Thanks.

Having trouble with itunes update. Error with itunes64.msi. Windows 8.1 64 bit. I tried uninstalling, but I am stuck now trying to reinstall.
It says itcan't find the itunes64.msi destination folder.

(1) Download the Windows Installer CleanUp utility installer file (msicuu2.exe) from the following Major Geeks page (use one of the links under the "DOWNLOAD LOCATIONS" thingy on the Major Geeks page):
http://majorgeeks.com/download.php?det=4459
(2) Doubleclick the msicuu2.exe file and follow the prompts to install the Windows Installer CleanUp utility. (If you're on a Windows Vista or Windows 7 system and you get a Code 800A0046 error message when doubleclicking the msicuu2.exe file, try instead right-clicking on the msicuu2.exe file and selecting "Run as administrator".)
(3) In your Start menu click All Programs and then click Windows Install Clean Up. The Windows Installer CleanUp utility window appears, listing software that is currently installed on your computer.
(4) In the list of programs that appears in CleanUp, select any iTunes entries and click "Remove", as per the following screenshot:
(5) Quit out of CleanUp, restart the PC and try another iTunes install. Does it go through properly this time?

The links with VARID table

Dear All,
We have deleted variants in table VARID in order to solve error CKMLRUN112. Error ckmlrun112 in parameters for closing entry definition
But we still get this error in ckmlcp.
Could anyone tell the links with table VARID?
Where we should delete this variants somewhere else too?
With best regards,
Kamila.

Sridhar,
While calling the transaction use call transaction tcode using i_bdcdata options from opt message into i_messages.
data: lws_cnt type char2,
lws_field type char15.
LOOP AT i_invoicing_plan INTO wa_invoicing_plan.
lws_cnt = sy-tabix.
CALL FUNCTION 'CONVERSION_EXIT_ALPHA_INPUT'
EXPORTING
input = lws_cnt
IMPORTING
output = lws_cnt .
CONCATENATE 'FPLT-AFDAT(' lws_cnt ')' INTO lws_field.
CONCATENATE wa_invoicing_plan-date+6(2)
wa_invoicing_plan-date+4(2)
wa_invoicing_plan-date+0(4) INTO lws_date
SEPARATED BY '.'.
PERFORM bdc_field USING lws_field lws_date.
CONCATENATE 'FPLT-FPROZ(' lws_cnt ')' INTO lws_field.
lws_perct = wa_invoicing_plan-percentage.
CONDENSE lws_perct.
PERFORM bdc_field USING lws_field lws_perct.
ENDLOOP.
While calling the transaction give like this:
<b>DATA: opt TYPE ctu_params.
opt-dismode = 'N'.
opt-updmode = 'A'.
opt-defsize = 'X'.
CALL TRANSACTION tcode
USING i_bdcdata OPTIONS FROM opt MESSAGES INTO i_messages.
LOOP AT i_messages.
ENDLOOP.</b>
Prakash.

I cannot update my ipad2 to ios5. Updating through iTunes on pc Windows Vista, Error message reads "cannot connect to iPad Software Update Server. Tried resetting network settings, still not connecting. Tried updating iTunes, still not connecting.

I cannot update my ipad2 to ios5. Updating through iTunes on pc Windows Vista, Error message reads "cannot connect to iPad Software Update Server. Tried resetting network settings, still not connecting. Tried updating iTunes, still not connecting.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
 Cheers, Tom

IPsec through link with low percentage of errors

Similar Messages

Maybe you are looking for