Issues with Hosted Exchange, UM and Lync 2013.

Hello everyone!
I am trying to deploy UM with Office 365 Hosted Exchange. We are using one Lync 2013 Standard Edition FE and have deployed one edge server. We have set up our firewall to host the Reverse Proxy.
We do not use wildcard certs. External DNS resolves the _sipfederation and sip._tls SRV records to the external face of the edge server. The edge server functions as it should for remote users and mobility.
I have tried to follow these instructions to the letter three times over to no avail.
http://y0av.me/2014/01/07/lyncum365/
Neither Snooper or Event Viewer show any particular issue, though when I try to dial out to voice mail I will get one to two rings and then 5 seconds of silence a fast busy, and finally "Call Unsuccessful".
When checking the firewall logs I notice a seemingly random 10.x.x.x address being sent to the firewall by the external leg of the edge server. Wireshark captures it as STUN packets on port 3478 being sent to port 3478. These are being dropped by our firewall.
I believe them to be RTP packets but I do not know if this is normal behavior. Has anyone any ideas?

My mistake. Here is the snooper result.
TL_INFO(TF_PROTOCOL) [edge\edge]0C4C.05E4::06/18/2014-15:43:34.153.0000000C (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265)) [3770767507]
Trace-Correlation-Id: 3770767507
Instance-Id: 2E5A
Direction: incoming;source="external edge";destination="internal edge"
Peer: exap.um.outlook.com:5061
Message-Type: response
Start-Line: SIP/2.0 488 Compression algorithm refused
From: sip:sip.domain.net;tag=08FB9ED133BA396696FE6546EA6F3031
To: sip:exap.um.outlook.com;tag=B8FFE4E9267ED6ECB78ADCC60126B53F
Call-ID: 66602CE1F9980BFA94AD
CSeq: 1 NEGOTIATE
Via: SIP/2.0/TLS 10.11.11.23:50752;branch=z9hG4bK2132316E.5B3AF52DE2753A36;branched=FALSE;received=207.46.5.9;ms-received-port=50752;ms-received-cid=60172700
Content-Length: 0
Server: RTC/5.0
TL_INFO(TF_NETWORK) [edge\edge]0C4C.05E4: :06/18/2014-15:43:34.153.0000000D (SIPStack,NegotiateLogic::SetCompressionType:NegotiateLogic.cpp(2701)) [559249495]( 00000079B1274FB8 ) Compression type is now CompOff
TL_INFO(TF_NETWORK) [edge\edge]0C4C.05E4: :06/18/2014-15:43:34.153.0000000E (SIPStack,NegotiateLogic::ProcessCompressionResponse:NegotiateLogic.cpp(2217)) [559249495]( 00000079B1274FB8 ) Peer refused [488] our request for compression
TL_INFO(TF_NETWORK) [edge\edge]0C4C.05E4: :06/18/2014-15:43:34.153.0000000F (SIPStack,NegotiateLogic::AdvanceOutboundNegotiation:NegotiateLogic.cpp(910)) [559249495]( 00000079B1274FB8 ) Outbound negotiation sequence is complete
$$end_record
And finally..
TL_INFO(TF_PROTOCOL) [edge\edge0C4C.05E4::06/18/2014-15:43:49.379.0000002E (SIPStack,SIPAdminLog::ProtocolRecord::Flush:ProtocolRecord.cpp(265)) [962697980]
Trace-Correlation-Id: 962697980
Instance-Id: 2E61
Direction: incoming;source="internal edge";destination="external edge"
Peer: fe1.domain.net:61254
Message-Type: request
Start-Line: BYE sip:uminternal.um.prod.outlook.com:5066;transport=Tls;ms-fe=CO1PR02MB111.namprd02.prod.outlook.com SIP/2.0
From: <sip:[email protected]>;tag=b736386270;epid=9bcee72318
To: <sip:[email protected];opaque=app:voicemail>;tag=eced411395;epid=07C3F2A933
Call-ID: 4266a095bdef8280d67c7e7df58446fc
CSeq: 2 BYE
Via: SIP/2.0/TLS 10.10.10.25:61254;branch=z9hG4bKC848F11A.A88BCA6858661A50;branched=FALSE
Via: SIP/2.0/TLS 10.10.10.125:49156;ms-received-port=49156;ms-received-cid=401200
Route: <sip:edge.domain.net:5061;transport=tls;opaque=state:Si;lr>
Route: <sip:exap.um.outlook.com:5061;transport=tls;epid=07C3F2A933;lr;ms-key-info=AAEAARc45bIQE6UJAYvPAR8eV4QTvCH3EE2Kxtie7I2PMCSj-2aArKHP8dStYlJe-9jphIkz_mDEkCD_v8hY-mghQEHD6-F12E7E14YG-TJ2gEcQE0Bx2r_rDB3LrzRZzgQ0WVvxreLPWGI80elWF-xfbc_X3JE8mOR2OB9KQM8-e9WOjfq2kj6CnDGeL0yzgz4OB8zm-ao03Yo4gMZ-BpwaxC3BNuvvVDJo9wqrYftq_Z3MIVewWrqcDt5Td4vxCsMiXdwEqtEIRKVvQoqboleBJAyQl-C3qGgfEoSkUnApFuTSnQYRa4kbZ1iPaACpdKT-VTQGjc9HXfps48YJCsIXW0Ab_NSM2uvhUyw900men1ukXSmoZoWZbwqe5siuWVUcFoQl1h1Jcy4lCyZUfDZoqPzDioLqTk9iUmS8fa-PAJjsq72yGjVB_y1aJSxtHVsw7MiDqOGOPqT3dmF-sINkeyuokCy8UCf_cQHmEHwVzZLUJqaVccr3QNCLsBzhcWSypnC60ZZphOKuwl6RvUXWICPf0ubLTL2ppC3tWEgFdUUWOPVd84uGlMcqRLKGb1qrmpj8Nu6Lte7t5n2pMEBCfgAe79t4GO0C5KScdKT_XBM1iIBRXdNkPKHfSgC-wPQgRikdw7vRD-hOWlN5Lay7-zkQ4Ag6rauszFTAwbft99OieAOxKIsgYcxXxcG6;ms-route-sig=fiEMuzbN4_PyEz_I5gG3g8FtqNAonwgZCoRnOq-ByfYEtywTZp-Hk_eAAA>
Max-Forwards: 69
Content-Length: 0
ms-client-diagnostics: 22; reason="Call failed to establish due to a media connectivity failure when both endpoints are internal";CallerMediaDebug="audio:ICEWarn=0x40003a0,LocalSite=10.10.10.125:6735,LocalMR=10.11.11.23:51430,RemoteSite=10.27.46.15:5286,RemoteMR=207.46.5.80:54106,PortRange=1025:65000,LocalMRTCPPort=51430,RemoteMRTCPPort=54106,LocalLocation=2,RemoteLocation=2,FederationType=0"
$$end_record

Similar Messages

  • Cisco VCS/Codian MCU and Lync 2013 integration

    Hi,
    I would like to know if Lync 2013 is supported to work with:
    - Cisco Tandberg VCS version x6.1
    - Cisco Codian 4.1 (comp. 6.16)
    Is it necessary to update both devices to be supported/homologated/qualified?
    Thanks

    Hi, Kent ... From what I'm seeing so far the challenges of integrating Cisco/Tandberg equipment and Lync 2013 are the same as what you may have already encountered with Lync 2010.  Since the Cisco endpoints and MCU cannot register directly to Lync 2010
    or 2013, you will need to leverage the VCS systems as your SIP gateway between them and Lync clients.  In Lync 2010 there were limitations as to the interoperability of the H.263/264 codec used by Cisco gear and the RTV codec that Lync was restricted
    to, and we often experienced frozen video feeds from Lync clients or an inability to connect to individual Cisco endpoints or conferences hosted by the Codian MCU.  Even though Lync 2013 will use H.264 as a codec for the video stream, I anticipate there
    will still be challenges interconnecting through the VCS as well as providing content between Lync and Cisco endpoints.  However, I expect an increase in the video quality since Lync 2013 supports higher resolutions and also uses a non-proprietary codec. 
    I expect content to still be unreliable for the Lync participant, even when using a Codian MCU.
    You will still need to setup your VCS with a separate Neighbor zone for the Lync 2013 server just as you did for Lync 2010.  I wouldn't hold my breath for Cisco to update the VCS software to accomodate the specific needs of Lync 2013, but at least the
    VCS will get the correct video codec and connect your call.  I don't know about you but I had to put my Cisco units and MCU into a separate SIP domain from the Lync pool, and then create a static route for the Cisco SIP domain on the Lync 2010 front-end
    server.  I expect to do the same in Lync 2013.
    Ideally, Microsoft and Cisco would agree that SIP is SIP, and whether an endpoint registers with VCS, UCM or Lync shouldn't be relevant.  Alas, it'll be a long, long time before that is true, certainly not as long as Microsoft and Polycom have
    such a tight bond.  I plan on implementing Lync 2013 in the next few months and will gladly post any progress here.  At this point my plan is to simply mirror the static route and configuration I have with Lync 2010.  My VCS and Codian units
    are running software versions just a little ahead of yours and work fine.
    Good luck!

  • Office 2010 and Lync 2013 installed caused Powerpoint to become corrupted from internet sources

    I'm finding that we're having problems with Office 2010 and Lync 2013.
    Our environment is setup as follows:
    Operating system: Windows 7 Enterprise 
    Office: Office 2010 (Word, Excel , Powerpoint, Access etc)
      Office 2013 (Only Lync has been installed for 2013)
    Problem: The issue is that when any Powerpoint documents come from internet sources (Such as Outlook or downloading directly from an internet browser), attachment manager deems the Powerpoint a security risk. When you open the Powerpoint it states that it's
    corrupt and needs to be repaired, when you try repairing the powerpoint, it says it's not going to be possible. 
    The only workaround is right clicking the power point in explorer and clicking properties, there's then a security prompt at the bottom of the dialog box and an option to "Unblock".
    The temporary fix: The fix is to remove Lync 2013 and the power point presentation open correctly from Internet sources.
    Attempted:
    I've attempted the following:
    - Build a laptop with a plain version of Windows 7 enterprise
    - Install Office 2010 Professional
    - Test powerpoints from internet sources (Working)
    - Install Lync 2013
    - Test powerpoints from internet sources (Same error)
    Any ideas?

    Just to let you know that switching off protected view in Powerpoint for files originating from internet sources and Outlook attachments is a workaround for the issue.
    I would be cautious about switching off Protected view though, here's a good article explaining the inner workings of Protected view:
    http://blogs.technet.com/b/office2010/archive/2009/08/13/protected-view-in-office-2010.aspx
    Concerning this problem, I also noticed that after removing Office 2013 and starting Powerpoint, a MSIEXEC instance is started.
    Presumably some DLLs are missing or some registry keys are missing when installed with Lync/Office 2013.
    I also went to the trouble of snap shotting the registry and using Procmon to see what gets loaded and added when Powerpoint repairs itself on first start after removing Office 2013.
    Unfortunately there are a number of things which change and couldn't be changed on the Office 2010 and Lync 2013 setup to fix the problem. 
    My advice would be the following:
    - Update to Office 2013 fully
    - Downgrade to Office 2010 Lync
    - Switch off protected view 

  • TS4363 Issues with the Exchange mail after upgrade to the lion x

    I can access my emails of my job in my iphone 5 and in my tablet. In the pass I used to access it by my macbook pro, but after updated to the IOS X, I got issues with the Exchange in the mac.

    Found the answer here: https://discussions.apple.com/thread/4138783

  • Unknown Presence in Lync 2010 and Lync 2013 co-existence

    I have lync 2010 and lync 2013 in my environment. Everything was working fine except when I moved the DNS of the Lync 2013 pool to the load balancer. When I did that, users on lync2013 could see the presence of users on Lync2010 pool but not vice versa. 
    I have point the Lyncdiscoverinternal.domain.com to the lync2013 pool DNS. I have opened migration ports on the load balancer but still not working. It works perfectly fine if I point the DNS of the pool to one server directly without going
    through the Load balancer VIP.
    Am I missing anything here?
    Thanks!
    Alert from TechNet Posting

    Hi Kojo Obeng Antwi,
    Please check out the following information.
    Deploying DNS load balancing on Front End pools requires you to perform a couple of extra steps with FQDNs and DNS
    records.
    A pool that uses DNS load balancing must have two FQDNs: the regular pool FQDN that is used by DNS load balancing (such as pool01.contoso.com), and resolves to the physical
    IPs of the servers in the pool, and another FQDN for the pool’s Web services (such as web01.contoso.com), which resolves to virtual IP address of the pool.
    In Topology Builder, if you want to deploy DNS load balancing for a pool, to create this extra FQDN for the pool’s Web services
    you must select the Override internal Web Services pool FQDN check box and type the FQDN, in the Specify the Web Services URLs for this Pool page.
    To support the FQDN used by DNS load balancing, you must provision DNS to resolve the pool FQDN (such as pool01.contoso.com) to the IP addresses of all the servers in the pool
    (for example, 192.168.1.1, 192.168.1.2, and so on). You should include only the IP addresses of servers that are currently deployed.
    Best regards,
    Eric

  • Co-Existence Lync 2010 and Lync 2013

    Hi,
    How do we check that CMS is moved from lync 2010 to Lync 2013 in Co-Existance environment lync standard edition.
    I know that users are moved form Lync 2010 to Lync 2013 but i don't if CMS is moved? And in the existing co-existence we have two edge servers Lync 2010 and Lync 2013. How can i check if traffic is  routing through Lync 2010 or lync 2013. 
    Because we want to Decommission the Lync 2010 STD Edition before doing this i want to make sure every thing go smooth.
    Please help me on this.
    Thanks
    Whenever you see a helpful reply, click on Vote As Helpful & click on Mark As Answer if a post answers your question.

    To find out if the CMS is moved:
    Get-CsConfigurationStoreLocation, if it's a standard server it will tell you the pool name.  If it's an Enterprise server, it will tell you the SQL server name associated with the pool. 
    http://technet.microsoft.com/en-us/library/gg412814.aspx
    Otherwise it's at the top of the topology builder (the top top part that says Lync Server in the left pane, under the Central Management Server spot in the right pane. 
    For a full decommission article, here's a decent one with screenshots.  As Ben said, if you can advise about the other places we could be more specific.
    http://www.oiboran.com/?p=1073
    Please remember, if you see a post that helped you please click "Vote As Helpful" and if it answered your question please click "Mark As Answer".
    SWC Unified Communications

  • Lenovo G560 - Issue with won't boot and black screen after HDD upgrade

    Lenovo G560 - Issue with won't boot and black screen after HDD upgrade.
     What happen: My laptop was working fine, no blue screen issue, no funny business at all. I bought a new SSD Intel 120 GB and thought it would be a good idea to replace the HDD. I shutdown and disconnected the power adapter, waited a couple of minutes and removed the battery. I opened up the back case and replaced the HDD. And put all the screws back and put the battery back in.
    Problem: The very first time I turned the power on, nothing happens besides a black screen. I pressed the dvd drive it works and opens up and closes. I waited for about 30 mins and still has blac screen. When I mean black screen, no bios menu, no logo, just a black screen with the fan sound on.
    I have tried these:
    1. Unplugged everything - battery, adapter, and pressed the power on button for about 60 seconds, nothing, the laptop turns on with the LED display on for both on and battery LED's. But nothing but black screen, no sound of windows loading just the fan and black screen.
    2. I tried putting back my old 2.5" and nothing but black screen.
    Thoughts and suggestions?
    Solved!
    Go to Solution.

    Hi Autoexit173,
    Welcome to Lenovo Community!
     As per the query we understood that you are facing issue with system not booting in your Lenovo G560 laptop.
    As you have mentioned that the system not booting, please try to remove the RAM and  turn on the system and check if you can hear any beep sound. Also try to clean the RAM slots and check for the issue.
    Click here for the steps to remove the RAM and refer page number 40.
    Hope this helps. Do post back if issue persists!
    Best regards,       
    Ashwin.S
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Is there an issue with Safari in Iphones and Ipads where it does not recognize option disabled="disabled" tag properly?

    Greetings everybody,
    I have run into a peculiar problem with the Safari browser on mobile platforms (IPad, IPod, IPhone) which I hope I can find a solution for in this community.
    I just launched a new website where I sell products with certain variations, for example please view this link: http://www.finerribbon.com/aegean-single-face-satin-ribbon.html
    On this particular product, the product variants are supposed to work in such a way where:
    If you select the value "1/8" from the "Choose Ribbon Width" field
    THEN
    The only options active and available to choose from in the "Choose Roll Size" field should be: 500 Yds, 20 Yds & Sample Swatch
    Now, if we browse to the above link in Safari using a desktop or a laptop, there are no problems at all, but if we browse to the above link using an IPhone or an Ipad, then we have a problem where all the options are available regardless of the values chosen, basically the above functonality does not work.
    I was told that there an issue with Safari in Iphones and Ipads where it does not recognize option disabled="disabled" tag properly, is this true? Can anyone advise me if there is a solution to this problem? I would sincerely apperciate it.
    Thank you very much for your time and help!

    Hi...
    I have run into a peculiar problem with the Safari browser on mobile platforms (IPad, IPod, IPhone) which I hope I can find a solution for in this community.
    Now, if we browse to the above link in Safari using a desktop or a laptop, there are no problems at all, but if we browse to the above link using an IPhone or an Ipad, then we have a problem
    At the top of this window you'll see the following:
    Apple Support Communities > Mac OS & System Software > Safari > Discussions
    This the Safari forum for the Mac OS X.
    Better that you post your topic here  > Developer Forums: Apple Support Communities
    I do see on my iPad what you are rreferring to. But you shoudl get the feedback you need in the developer forum.

  • I set up my iCloud account on iPad with an exchange account and aol account.  I can see exchange and aol emails but not those from .me account or apple email.  I got it to show all 3 accounts on my iPhone with no problem.  Hat am I missing?

    I set up my iCloud account on iPad with an exchange account and aol account.  I can see exchange and aol emails but not those from .me account or apple email.  I got it to show all 3 accounts on my iPhone with no problem.  Hat am I missing?

    I'm having a similar problem, but I do have the key and is not working anyway.
    My old pc was running on windows 7 and my new one is an apple running on Lion.
    My phone is an Iphone IV and I can see all the bookmarks there.
    In order to sync, what I did was click on the "I don't have the device with me", I entered the key that was provided and the process finish ok. It says congratulations, etc, etc.
    But the bookmarks are not there, I tried merging data and replacing data on this computer options but is the same.
    Any suggestions?

  • Lync 2010 and Lync 2013 blinking icon in taskbar not working properly

         Hi,
         We're experiencing a strange behaviour. Lync IM notifications are supposed to work this way below:
         1) Notification bubble on the right-bottom corner
         2) After a few seconds, a blinking icon in the task bar
         3) After a few seconds, a coloured icon remains in the task bar
         Some of our users, both Lync 2010 and Lync 2013, go 1) and 2) but then icon won't remain in the task bar, so they don't realize they have a conversation waiting (Windows XP and Windows 7).
         If they open the icon, the conversation is there and coloured, and they can answer.
         In my computer, it has also happened but most of the time it works fine (testing it, maybe it works 15 times and fails 1). Nevertheless, a lot of people is suffering from this strange behaviour.
         We have looked into the causes but haven't found anything.
         Any clue?
         Thanks!

    How long have you seen the problem?
    What version of your Lync client? Try to update your Lync client to the latest version.
    Try to repair office 2013.
    Uninstall and reinstall Lync 2010.
    Please install Lync 2013 or Lync 2010 on a fresh installation of Window to check if you can still see this problem.
    Lisa Zheng
    TechNet Community Support

  • TS1398 I have the ipad retina display version - I have a BIG issue with this when out and about that on about 50% of the time will it see my HTC mobile WiFi hotspot - rebooting either, or both devices doesn't cure the problem it drives me MAD!!!!

    I have the ipad retina display version - I have a BIG issue with this when out and about, that only about 50% of the time will it see my HTC mobile WiFi hotspot - rebooting either, or both devices doesn't cure the problem it drives me MAD!!!!
    The HTC hotspot works fine with everything else I connect to it.
    Also - ipad will not connect to my HTC via bluetooth. Again, I can connect to everything else with my HTC other than my ipad.
    I have to say this is my first venture into Apple products and I have always wanted to get away from my windows based laptop to get a MacBook, the problems I have had (flash player etc) & continue to have (as above) are putting me right off swapping over. I HATE technology that doesn't work and my ipad has been hard work!

    I stated my ipad as being an ipad2, but I now think it is a 3??? It was new Jan this year and is the 64gb retina display version.
    I really would like to get to the bottom on this problem wit mobile hotspots as it is sitting on my desk next to me now and I cannot get it to connect to my HTC mobile hotspot!!!! It might be taking a flying lesson soon at this rate!!! Grrrrrrr...........

  • Sync issues with iPhone 6 Plus and iTunes

    I'm having issues with syncing my iPhone and iTunes.
    I am running: Mavericks 10.9.3 | iTunes 11.4 | iOS 8.0.2
    Every time I try to sync my iPhone 6 Plus with iTunes, the sync process gets stuck on step 5 of 5 (waiting for changes to be applied).  The longest this has occurred for is 2hrs.  After this time I have stopped the sync and ejected my iPhone.
    I had another issue with my phone when playing music.  When going to play music, I was given the error message saying that the song could not be found.  I connected my iPhone to iTunes and went to the tab in summery page, 'on this iPhone'.  I found the song and could see that next to the song was a small what looked like dotted grey circle.  After Googling this, I found a video saying that if i was to remove all my music and then add it again, this should fix the problem with this song.  I did this and this was when the issue occurred again.
    I unticked the option to remove all music but the sync did not finish. So I cancelled the sync, ejected my iPhone and tried again.  This time, the summery page of my iPhone said there was no music on my iPhone and the 'on this iPhone'  tab, this all so said there was no music however, my music was still on my iPhone including the song that would not play.  All played ok.
    I have read lots in the Apple forums about lost of difference reason this may be happening.  Things like bugs in iOS 8, app updates being transferred during the sync process, the latest iTunes version has bugs and even a dodgy USB cable could cause it.  My iPod running iOS 5 syncs all ok but I get this problem as well on my iPad Air.
    I all so had this issue with my old iPhone 4S.  The problem occurred when running iOS 7 and 8 on the 4S.  When I had it on the 4S, I did a restore of the 4S 4 times and thought I had found the issue down too a dodgy app.  However, now that it has happened on my new iPhone and still not using that app, could this be an issue with my Mac/iTunes?
    I am in contact with Apple Care, but this is such a long process. 
    So if anybody could please offer any advice on this or steps to try to maybe solve the issue, it would be really helpful.   Or if anybody is experiencing the same problem, it would be good to know its not just my devices and Mac producing this sync problem.
    I will update my post with any information provided by Apple Care as and when I get it.
    Thanks for reading and thanks for your time.
    Mark. 

    Hi,
    Just wanted to updated my original post and give some more information on this issue that I'm having with my iOS devices running iOS 8.0.2 and iTunes 11.4.
    Firstly I just want to updated my details about what version of Mavericks I'm running.  I'm running 10.9.5 - I put the wrong version down in my original post.
    So over the last week, I have had a few phone calls with Apple Care an am dealing with a senior technical advisor about this issue.
    I have been given some instructions that I am currently working through to see if it solves the sync issue with iTunes and my iOS devices. 
    The Apple Care advisor has pointed out that a iTunes version issue with music that I have ripped to iTunes and the current iTunes version could be what is causing the problem.  For example, every song that I have purchased from iTunes since having an account, I was told are all exactly the same the same when it comes down the to data/information about that track/album that iTunes stores with the music but when it comes to music that I have added to iTunes myself from a CD,  this was added and encoded with the version of iTunes that was running at the time of adding the music.  So going through all the music that I added to iTunes over the last 10 years, you can imaging that there was lots of mixed version of iTunes linked to lots of different music.
    At the moment, I'm having to go through all my music and find any that I have added and create a new ACC version of that music and delete the old version.  However, due to the amount of music that I have, this is going to take a long time.  When I was on the phone to the Apple Care advisor, we did several albums as a test and they all synced over to my iPhone.  This may just have been luck though at that time.
    Now, I'm not saying that this will solve the problem that I have with the sync issue but I am going to try it and see how I get on.  The only down side to this fix as far as I can see at the moment, is  that when it's all done, I think I will have to fully restore all my iOS devices to get music on to them.
    I will of course updated this topic when I have got through all my music and tried to sync my iOS devices.
    Thank you all for your comments.

  • I have been having issues with not receiving texts and voicemails daily, for a few months now. If I turn the phone completely off, when I turn it back on the messages will flood in from hours before. I can't be continually turning off my phone in case som

    I have been having issues with not receiving texts and voicemails daily, for a few months now. If I turn the phone completely off, when I turn it back on the messages will flood in from hours before. I can't be continually turning off my phone in case someone left me a message. How do I resolve this issue?

    Wifi:  my Cell phone will remember 10 wifi connections.  So delete any you don't use often and your home wifi and try to enter home wifi again.
    if it still won't connect to home wifi, call your internet provider for help.  You may need a newer router or different settings Or upgraded service.   Your phone seeks the best connection and will refuse lesser connections.
    last resort.  Backup the phone.  Do a full reset, then restore as new with the backup.
    if still not fixed, go back to apple and insist on repair or replacement.
    HOWEVER.   voicemail is not a wifi issue, it's a carrier function, which is why the SIM card is a suspect.

  • Issues with Bex query structures and Crystal Reports/Webi

    Hi experts,
    I'm having an issue with Bex Query structures and nulls. I've built a Crystal Report against a Bex query that uses a Bex Query structure. The structure looks like the following
    Budget $
    Budget %
    Actual $
    Actual %
    Budget YTD
    etc
    if I drag the structure into the Crystal Report detail section with a key figure it displays like this
    Budget $     <null>
    Budget %     <null>
    Actual $     300
    Actual %     85
    Budget YTD     250
    the null values are displayed (and this is what is required). However if I filter using a Record selection or group on a profit centre then the nulls along with the associated structure component are not displayed.
    Actual $     300
    Actual %     85
    Budget YTD     250
    Webi is also behaving similarly. Can anyone explain why the above is happening and suggest a solution either on the Bex side of things or on the Crystal Reports side of things? I'm confused as to why nulls are displayed in the first example and not the second.
    Business Objects Edge 3.1 SP2
    SAP Int Kit SP2
    OS: Linux
    BW 701 Level 6
    Crystal Reports 2008 V1
    Thanks
    Keith

    Hi,
    Crystal Reports and Web Intelligence will only show data which is in the cube. You could have an actual 0 or Null entry whithout grouping but by changing the selection / grouping in the report the data does not include such entry anymore.
    ingo

  • HT1349 Has anyone had issues with the iphone 4s and facebook.

    Has anyone had issues with the iphone 4s and facebook. I have downloaded the app and sometimes it will let me log in and then it will log me out and not let me back in. I have deleted and downloaded it several times and nothing is working. HELP!

    @razmee: rather unhelpful.
    @tata - we're having the same trouble, and the only solution we've found doesn't fix it.
    1) uninstall
    2) login on PC/MAC and change password
    3) reboot iphone
    4) install facebook app, reboot again
    5) login from iphone. 
    No joy.
    Safari works, but not for the apps.
    Of course, it's Facebook that has to fix this.

Maybe you are looking for