It seems I'm the only one DownThemAll doesn't work for, as it only downloads the html, never the content, despite trying thousands of different configurationsnt
I am a frequent downloader, and everywhere I search, people are raving about downThemAll. But I can not get any results out of it, as it will only download junk files. I can't believe no one has experienced this. Can you help? Thank you
gerrydee@tesco .net wrote:
after downloading maverick,which stopped halfway through,installed new harddrive on which i installed lion 10.7.5. couldn't re-install iphoto as my os was not above 10.8 yet i had it on 10.7 previously.along with other programs.restore from my backup worked along with everything i had before but slowly - over a period of startup and sleep a variety of problems arose preventing me from not using programs. for instance : instruction to download iphoto from app store again - then it tells me app store not available.it seems almost as if some joker is sharing my computer to deliberately prevent me from achieving anything.
anybody else get this sort of problem? how do you sort it? without huge expenditure which apple seem to expect.
i'm only a customer after all. gerry
Reinstall the backup you made before choosing to update Mavericks.
OS X Mavericks: Revert to a previous OS X version
Cheers
Pete
Similar Messages
-
The back button doesn't work for some websites after downloading version 4.0
I recently downloaded firefox version 4.0. Upon downloading it I had a few issues occur with my browser. One issue was that all of my bookmarks that were on my toolbar disappeared. Also, when I visit a website and am browsing through it, if I want to go back to a previous page the back button doesn't work properly. Instead of sending me back to the previous page I was viewing it sends me all the way back to the home page or wherever I started on that website. This problem basically affects all websites that I visit. I would like to uninstall the new version of firefox and just go back to my old one if that's possible? Thanks
To respond to your comments first of all, the Bookmarks toolbar has been removed in Firefox 4.0
The back button should work as it normally does, but you can also right click it and select it from the list.
To revert to a previous version of Firefox, download v3.6.16 from here: [http://www.mozilla.com/en-US/firefox/all-older.html Download Firefox v3.6.16]
Then uninstall Mozilla Firefox 4.0 choosing to keep your bookmarks, customizations etc.
Finally run the Firefox installation file you downloaded earlier. -
With my i phone 4 , the Push notifications doesn't work for apps like (fb viber , whatsapp etc ) it only works for the official apps like message even when im using the phone, has this probleme with the iOs 6.0.1 and also with the iOs 6.1
This isn't an issue. Notice the screen prior to the one that shows usage has an iCloud section and a Manage Storage button. For this button to activate ios needs to download a few kb from icloud. Switching back to this screen forces ios to download those few kb.
-
[kde] "Only show tasks from the current desktop" doesn't work for max
Hi,
I have two monitor setup (laptop + main monitor) and I would love to use "Only show tasks from the current desktop" option in KDE Task Manager but for some strange reason it doesn't work for me. Well, it works but only partially - for restored/unmaximized windows. When I maximize one it appears on the Taskbar on both screens. Is this normal? May it be due to the fact that I've placed Taskbar on top of the screens?Did you miss this bit
"Graphics : 1 GB NVIDIA Quadro 600 (1DP & 1DVI-I) (1DP-DVI & 1DVI-VGA adapter) (ELGA13) 1"
And the final image clearly states the type of Graphics Card he has
Photoshop CS6 GPU FAQ
Tested video cards for Photoshop CS6
Adobe tested the following video cards before the release of Photoshop CS6. This document lists the video card by series. The minimum amount of RAM supported on video cards for Photoshop CS6 is 256 MB. Photoshop 13.1 cannot display 3D features if you have less than 512 MB of VRAM on your video card.
Important: This document is updated as newly released cards are tested. However, Adobe cannot test all cards in a timely manner. If a video card is not listed here, but was released after May 2012, you can assume that the card will work with Photoshop CS6.
Adobe tested laptop and desktop versions of the following cards. Be sure to download the latest driver for your specific model. (Laptop and desktop versions have slightly different names.)
nVidia GeForce 8000, 9000, 100, 200, 300, 400, 500, 600 series
nVidia Quadro 400, 600, 2000, 4000 (Mac & Win), CX, 5000, 6000, K600, K2000, K4000, K5000 (Windows & Mac OS) -
How can I add a new Template to My Templates in Pages? I've read most of the discussions on the subject but it doesn't work for me. By the time I reach the Templates folder, I only see templates for Numbers and not for Pages. Need help, please. Thanks
Si vous avez utilisé la commande Save As Template depuis Pages, il y a forcément un dossier
iWork > Pages
contenant Templates > My Templates
comme il y a un dossier
iWork > Numbers
contenant Templates > My Templates
Depuis le Finder, tapez cmd + f
puis configurez la recherche comme sur cette recopie d'écran.
puis lancez la recherche.
Ainsi, vous allez trouver vos modèles personnalisés dans leur dossier.
Chez moi, il y en a une kyrielle en dehors des dossiers standards parce que je renomme wxcvb.template quasiment tous mes documents Pages et wxcvb.nmbtemplate à peu près tous mes documents Numbers.
Ainsi, quand je travaille sur un document, je ne suis pas ralenti par Autosave.
Désolé mais je ne répondrai plus avant demain.
Pour moi il est temps de dormir.
Yvan KOENIG (VALLAURIS, France) mercredi 23 janvier 2011 22:39:28
iMac 21”5, i7, 2.8 GHz, 4 Gbytes, 1 Tbytes, mac OS X 10.6.8 and 10.7.2
My iDisk is : <http://public.me.com/koenigyvan>
Please : Search for questions similar to your own before submitting them to the community -
Every time I download a new app or update an old one it doesn't work. It gives an error message saying it is unable to download the application. I have 2 choices. Retry or done. Retry doesn't work so I press done. What can I do to fix this? Someone please help!
Try using Google's DNS instead of the one your IPS is providing.
- To change on the iPod go to Settings>wifi and change the DNS to 8.8.8.8
- For the computer see:
Public DNS — Google Developers
- Did anything happen to your router right before this started? Maybe the router is blocking the port used. -
The vga adapter (for a Benq projector, for example) is only for Ipod touch 4g? I have an 2g. Doesn't work for this?
Thanks in advance.The VGA is for the 4G iPod only. The 2G can use the composite and component cables.
http://support.apple.com/kb/HT1454 -
I just updated my Apple ID to a current email address, it worked on my laptop but my phone is still using the old one and neither password works. I can't download or use anything other than phone calls and texting on my phone now. Help!
go to settings
then to store
tap your id then click sign out
then sign back in and you should be fine -
I have purchased the new apple earpods a while ago (few months). And I was wondering if I can use my warranty cause one earpod doesn't work anymore.
So please help!See this: Using iPad or iPod with multiple computers, http://support.apple.com/kb/HT1202
-
The wifi at my school isn't very good. And I can't send iMessages through it. It works for some apps like score center and my radar app, but doesn't work for other apps like clash of clans and iMessage. How can I get it to work on my school wifi. I have an iPhone 4S on AT&T and iOS 7.04
In a roaming network, your "main" router is the device that would require port mapping/forwarding to be configured in order to access the IP camera from the Internet. This router is also the one that would be provide the private IP address for the camera which you will want to be a static one.
So as you described your network, the IP cameras should be getting an IP address or you assigned it a static one and this is the address that you would enter in the Private IP address (or equivalent depending on the router used) field when setting up port mapping.
If you are not able to access this camera from the local network, then this should be troubleshot first. -
Auto To working for one material and not working for other material
Hi,
Hope everybody is doing fine.
I have configured the auto TO. Its working fine for one material and not working for the other material. I checked the material master and wm 1,2 views have the same fileds / values. What could be wrong?
I didn't setup the back ground processing job. Is that is affecting it?
thanks for any help.
regrads,
KHANThnaks,
You are right but then what could be wrong? Its working for one material and not working for otehr material? Any clue?
Appreciate your time charlie -
My mic for my iPhone 4S only works on speaker phone and doesn't work for Siri. What can I do?
My mic on my 4s only works on speaker phone in calls. It also doesn't work for Siri or voice memos. Is there any way to fix this without having to buy new parts or exchange it?
Hello there, mbrda92.
The following Knowledge Base article provides some great, in-depth steps for troubleshooting your issue:
iPhone: Hardware troubleshooting
http://support.apple.com/kb/ts2802
Particularly of note:
Will not turn on, will not turn on unless connected to power, or unexpected power off
Verify that the Sleep/Wake button functions. If it does not function, inspect it for signs of damage. If the button is damaged or is not functioning when pressed, seek service.
Check if a Liquid Contact Indicator (LCI) is activated or there are signs of corrosion. Learn about LCIsand corrosion.
Connect the iPhone to the iPhone's USB power adapter and let it charge for at least ten minutes.
After at least 30 minutes, if:
The home screen appears: The iPhone should be working. Update to the latest version of iOS if necessary. Continue charging it until it is completely charged and you see this battery icon in the upper-right corner of the screen . Then unplug the phone from power. If it immediately turns off, seek service.
The low-battery image appears, even after the phone has charged for at least 20 minutes: See "iPhone displays the low-battery image and is unresponsive" symptom in this article.
Something other than the Home screen or Low Battery image appears, continue with this article for further troubleshooting steps.
If the iPhone did not turn on, reset it while connected to the iPhone USB power adapter.
If the display turns on, go to step 4.
If the display remains black, go to next step.
Connect the iPhone to a computer and open iTunes. If iTunes recognizes the iPhone and indicates that it is in recovery mode, attempt to restore the iPhone. If the iPhone doesn't appear in iTunes or if you have difficulties in restoring the iPhone, see this article for further assistance.
If restoring the iPhone resolved the issue, go to step 4. If restoring the iPhone did not solve the issue, seek service.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro. -
Apache Sling JCR Resource Resolver doesn't work for the anchor tags which is been rendered through j
Certainly I realized that Apache Sling JCR Resource Resolver doesn't work for the anchor tags which is been rendered through jquery or javascript.
e.g.
In Felix Console , in Apache Sling JCR Resource Resolver configuration I have added following mapping.
/content/myproject/-/
So If any anchor tag is there like <a href="/content/myproject/en.html"> click me </a> then it will be mapped to "/en.html" automatically.
But the problem is there in following scenario.
I have an anchor tag as follows.
<a href="#" id="test"> click here </a>
And I am assigning the href to anchor through JQUERY.
<script>
$("#test").attr("href","/content/myproject/en.html");
</script>
Ideally this should have been mapped to "/en.html".
But it is not mapping to "/en.html". It still shows "/content/myproject/en.html".
How to resolve this.
Thanks,
SaiIn a servlet you have access to the resourceResolver so if you know which attributes contain links then it's relatively easy to apply resourceResolver.map to those links.
Your challenge is clearly how do you know which attributes are links and which aren't. Its is the same challenge that makes parsing the response and rewriting it on the way out difficult - the JSON doesn't have any semantic meaning so how do identify which attributes require rewriting. There really is no good answer ot that question in my experience - all the options have down sides.
Create some convention - all attributes matching this pattern X get mapped before being converted to JSON (could be attributes whose name ends in link, or it could a convention applied to the value of the attribute - if the attribute is a string that starts with /content apply the resource resolver mapping. In this case you have train your developers to follow this convention which is the down side.
Create some configurable list of attribute names that require mapping. This is brittle, requires training and is easy to break.
Implement a client side version of the resource resolver mapping. It wouldn't be as full proof as server side mapping (because that takes into account but you could make it work for simple logic like stripping of /content/site/en. If ou are just trying to solve the simple version of this issue - stripping off the top of the repository path this might be your best option.
Not worry about it and set up Apache 301 redirects that catch any long URLs and redirect them to short URLs (so configure apache to look for any URL matching /content/site/en and strip off /content/site/en and do a 301 redirect to the shortened URL. You end up with a lot of extra HTTP request because of all the 301s but it would work (I wouldn't recommend this option - but it is possible). -
I upgraded my 3 yr old iMac to Snow Leopard (OS X 10.6) and now my HP C4150 Scanning function doesn't work (not recognized). I downloaded updated Drivers from the HP site and installed them, but still no joy. Any suggestions?
aspaceman,
Perhaps I owe you an apology. Having re-read that downloading from HP was unsuccessful I feel uncomfortable. Can I suggest you update your 10.6 system (as noted in your profile) to 10.6.8 (if it is not already there) by using the
Mac OS X 10.6.8 Update Combo v1.1 combo update plus any software updates that then apply. -
How do I uninstall Firefox 4 and get the previous version back?
The upgrade has many problems and doesn't work for me.new version is the worst Firefox ever, no lip.
Maybe you are looking for
-
Hi , I am getting error while adding new ECC variable in ICM. PFB the error message. " The Maximum size of all Expanded Call Variable in the Computer Telephony Integeration Server is 2500 bytes. Saving these schanges would require 2795 bytes. will th
-
I have to use some podcasts for a Uni. assignment. That is to say, I have to burn them on a CD-ROM together with other audio and non-audio files. How can I do that? Does iTunes saves the podcasts on a hard-drive directory? Or how else could I do? Tha
-
What exactly is a failure group?
Oracle Version : 10GR2 2 node RAC running on Solaris I am trying to understand what a failure group is. Googling didn't help much . If i want to store 1 TB of data and needs it be to proteced either by NORMAL or HIGH redundancy and i have 3 slices of
-
Equivalent to MS Paint on Apple Software
Ref my recent cry for help in doing all my website work on my Apple. Many thanks for help so far - KOMPOZER as a subsititute for MS Frontpage seems excellent and a lot cheaper at nothing than Dreamweaver! One last question. MS Paint meets my needs fo
-
Dear Experts, I have to connect my BI System with Microsoft Sql Server. I have read so many standard documents but still not sure how to proceed with it. My First conern is related to DBSL Library . From where we can downlaod and which file need to