Iwlist scanning gives: Interface doesn't support sc [solved]

When I'm trying to scan for all available networks I get:
# iwlist eth1 scanning
eth1 Interface doesn't support scanning : Operation not supported
My wireless card works fine if I set every parameter manually. I'm currently using the orinoco drivers that came along with ArchLinux.
It seems like that the version of the orinoco drivers installed doesn't support the scan stuff. But building the new orinoco drivers failed with
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c: In function `orinoco_ pci_suspend':
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c:330: error: too many a rguments to function `pci_save_state'
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c: In function `orinoco_ pci_resume':
/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.c:347: error: too many a rguments to function `pci_restore_state'
make[2]: *** [/usr/local/download/orinoco/orinoco-0.15rc2/orinoco_pci.o] Error 1
make[1]: *** [_module_/usr/local/download/orinoco/orinoco-0.15rc2] Error 2
make[1]: Leaving directory `/usr/src/linux-2.6.11.3-ARCH'
make: *** [modules] Error 2
So I did try the wlan-ng26 driver downloaded and installed with pacman.
I remove the orinoco modules with
[root@ArchThinkpad orjanp]# modprobe -r orinoco_pci
But when I try to insert the prism2_pci module, it doesn't exist. Why?
[root@ArchThinkpad orjanp]# modprobe prism2_pci
FATAL: Module prism2_pci not found.
Any heads up on what to do?
This is iwconfig before removing the orinoco modules.
[root@ArchThinkpad orjanp]# iwconfig
lo no wireless extensions.
sit0 no wireless extensions.
eth0 no wireless extensions.
eth1 IEEE 802.11-DS ESSID:"" Nickname:"Prism I"
Mode:Managed Access Point: 00:00:00:00:00:00 Bit Rate:11 Mb/s
Tx-Power=15 dBm Sensitivity:1/3
Retry min limit:8 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=0/92 Signal level=-68 dBm Noise level=-122 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
This is lspci
[root@ArchThinkpad orjanp]# lspci
00:00.0 Host bridge: Intel Corp. 82845 845 (Brookdale) Chipset Host Bridge (rev 04)
00:01.0 PCI bridge: Intel Corp. 82845 845 (Brookdale) Chipset AGP Bridge (rev 04)
00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BAM/CAM PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corp. 82801CAM ISA Bridge (LPC) (rev 02)
00:1f.1 IDE interface: Intel Corp. 82801CAM IDE U100 (rev 02)
00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus (rev 02)
00:1f.5 Multimedia audio controller: Intel Corp. 82801CA/CAM AC'97 Audio (rev 02)
00:1f.6 Modem: Intel Corp. 82801CA/CAM AC'97 Modem (rev 02)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M7 LW [Radeon Mobility 7500]
02:00.0 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01)
02:00.1 CardBus bridge: Texas Instruments PCI1250 PC card Cardbus Controller (rev 01)
02:02.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan chipset (rev 01)
02:08.0 Ethernet controller: Intel Corp. 82801CAM (ICH3) PRO/100 VE (LOM) Ethernet Controller (rev 42)
This is lsmod before removing orinoco.
[root@ArchThinkpad orjanp]# lsmod
Module Size Used by
radeon 78336 1
ohci_hcd 23048 0
ehci_hcd 36488 0
irtty_sir 7552 0
sir_dev 18636 1 irtty_sir
irda 144184 1 sir_dev
crc_ccitt 2432 1 irda
parport_pc 29252 0
parport 38600 1 parport_pc
rtc 13260 0
pcspkr 4044 0
eepro100 32528 0
orinoco_pci 7552 0
orinoco 44172 1 orinoco_pci
hermes 9472 2 orinoco_pci,orinoco
yenta_socket 23560 0
rsrc_nonstatic 11648 1 yenta_socket
pcmcia_core 51488 2 yenta_socket,rsrc_nonstatic
snd_intel8x0m 19396 0
snd_intel8x0 34624 0
snd_ac97_codec 79224 2 snd_intel8x0m,snd_intel8x0
snd_pcm_oss 56224 0
snd_mixer_oss 21120 1 snd_pcm_oss
snd_pcm 98564 4 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss
snd_timer 27268 1 snd_pcm
snd 59492 7 snd_intel8x0m,snd_intel8x0,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_timer
soundcore 10848 1 snd
snd_page_alloc 10244 3 snd_intel8x0m,snd_intel8x0,snd_pcm
i2c_i801 8972 0
i2c_core 23296 1 i2c_i801
usbhid 47744 0
uhci_hcd 33424 0
usbcore 125560 5 ohci_hcd,ehci_hcd,usbhid,uhci_hcd
shpchp 100996 0
pci_hotplug 34760 1 shpchp
tsdev 8256 0
joydev 10560 0
evdev 9984 0
cpufreq_powersave 2176 0
cpufreq_userspace 5680 0
p4_clockmod 6164 0
speedstep_lib 4868 1 p4_clockmod
freq_table 5008 1 p4_clockmod
e100 37760 0
mii 5760 2 eepro100,e100
nls_cp437 6144 1
vfat 14976 1
fat 41884 1 vfat

orjanp wrote:
Thanks.
I installed the 0.15RC1 version of the Orinoco drivers found here.
I rebooted but I still had the 0.13 version. I did a make and make install as the readme file said.
What do I have to do to update the driver?
do you use a PKGBUILD?
update the driver: if it was copied to the right place and the kernel knows about it (depmod -a) it should work
for a start, check under
ls -la /lib/modules/`uname -r`/kernel/drivers/net/wireless/
that your module is installed under the correct location (the orinoco files should be newer than the other ones)
if this is so, make sure you are depmod -a (as root) ... and if even this is ok, then either you are running the new modules or something strange happened

Similar Messages

No interfaces shown in network manager [SOLVED]

Hi All,
I have just done a fresh install of Arch on my new Sony Vaio VGN-FW53GF, all goes well, except for Network Manager.
I can use my wired connection ok as eth0 shows up as active when I hover over the kde applet in the task bar. However when I go to "Manage Connections"
I do not see any Wireless networks or even my "working" wired connection in any list.
Wireless seems to be working as iwconfig shows an interface.
wlan0 IEEE 802.11abgn ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
But a scan gives this:
iwlist wlan0 scan
wlan0 Interface doesn't support scanning : Network is down
This machine is using the Intel driver "iwlagn" supplied by the kernel (2.6.31).
My /etc/rc.conf is:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Pacific/Auckland"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
MODULES=()
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="Laptop2"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
#Static IP example
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
wlan0="dhcp"
INTERFACES=(!eth0 !wlan0)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=(main)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng !network hal networkmanager netfs crond)
Can anyone offer some suggestion on how to get network manager going, I would like to use it. In the past
I have used Wicd, but it has some limitations.
Cheers,
Bernie
Last edited by bmentink (2009-12-24 04:19:49)

bmentink wrote:
Ok, I found the issue. I was missing the firmware for the card. I downloaded firmware from the intel site as per the wiki on wireless and
my interface comes up (shown with ifconfig) and I can see all the networks.
However, I cannot seem to connect to my network with WPA. When I go to connect I get network manager thinking the access point is WEP and asking for pass phrase.
If I select WPA(personal) and fill in a password, nothing happens .... just says unavailable.
Can anyone give some idea's here. I have not used network manager before for WPA.
Cheers,
Bernie
I use WPA2 with network manager without a problem. It should "just work", im not sure why you have issues, can you switch your router to a different security protocol to test?

2011 outlook gives the following error: "Authentication failed because Outlook doesn't support any of the available authentication methods."

Upgraded my computer to 10.9.2 Mavericks and now my 2011 outlook gives the following error: "Authentication failed because Outlook doesn't support any of the available authentication methods." Anybody know how to fix it? Thank you.

I got the following from the microsoft Web site. Also, the SMPT port must be overwriten. Use port 587
This article contains information about the compatibility of Microsoft Outlook for Mac 2011 and Apple iCloud. Outlook for Mac 2011 does not support Apple iCloud calendar (CalDAV) and contact (CardDAV) synchronization. Outlook for Mac 2011 does support iCloud Mail. For steps on how to configure your iCloud email account in Outlook for Mac 2011, go to the "More Information" section of this article.
To configure your Apple iCloud email account in Microsoft Outlook for Mac 2011, follow these steps:
Start Outlook 2011.
On the Tools menu, click Accounts.
Click the plus sign in the lower-left corner, and then select E-mail.
Enter your E-mail Address and Password, and then click Add Account.
Note: The new account will appear in the left navigation pane of the Accounts dialog box.
Enter one of the following in the Incoming server box:
mail.me.com (for me.com mail addresses)
mail.mac.com (for mac.com mail addresses)
Click to select Use SSL to connect (recommended) under the Incoming server box.
Enter one of the following in the Outgoing server box:
smtp.me.com (for me.com mail addresses)
smtp.mac.com (for mac.com mail addresses)
Click to select Use SSL to connect (recommended) under the Outgoing server box.
After you have entered the incoming and outgoing server information, Outlook 2011 will start to receive your email messages.
Note: You can click Advanced to enter additional settings, such as leaving a copy of each message on the server.

Weblogic Pool Driver doesn't support XA driver

          I am trying to set up a JDBC Strore for a JMS Server. The JDBC Store uses the Oracle
          XA driver (oracle.jdbc.xa.client.OracleXADataSource). However whaen the JMS server
          starts it gives me the following exception: Weblogic Pool Driver doesn't support
          XA driver. Any idea what I am doing wrong? I am using WL 8.1 SP2. THe full error
          trace is shown below:
          <Jan 15, 2004 3:05:09 PM EST> <Alert> <JMS> <BEA-040052> <JMSServer "jmsTestJmsServer1"
          store failed to open java.io.IOException: JMS JDBC store, connection pool = <jmsTestJdbcConnectionPool>,
          prefix = <JMS1>: cannot determine DBMS type
          <java.sql.SQLException: Pool connect failed : java.lang.Exception: Weblogic Pool
          Driver doesn't support XA driver, Please change your config to use a Non-XA driver
          <     at weblogic.jdbc.common.internal.JDBCUtil.wrapAndThrowResourceException(JDBCUtil.java:160)
          <     at weblogic.jdbc.pool.Driver.connect(Driver.java:156)
          <     at weblogic.jms.store.JDBCIOStream.checkDbmsType(JDBCIOStream.java:1490)
          <     at weblogic.jms.store.JDBCIOStream.open(JDBCIOStream.java:420)
          <     at weblogic.jms.store.JMSStore.open(JMSStore.java:224)
          <     at weblogic.jms.backend.BEStore.open(BEStore.java:262)
          <     at weblogic.jms.backend.BEStore.start(BEStore.java:151)
          <     at weblogic.jms.backend.BackEnd.openStores(BackEnd.java:1171)
          <     at weblogic.jms.backend.BackEnd.resume(BackEnd.java:1290)
          <     at weblogic.jms.JMSService.addJMSServer(JMSService.java:2241)
          <     at weblogic.jms.JMSService.addDeployment(JMSService.java:2012)
          <     at weblogic.management.mbeans.custom.DeploymentTarget.addDeployment(DeploymentTarget.java:330)
          <     at weblogic.management.mbeans.custom.DeploymentTarget.addDeployments(DeploymentTarget.java:590)
          <     at weblogic.management.mbeans.custom.DeploymentTarget.updateServerDeployments(DeploymentTarget.java:568)
          <     at weblogic.management.mbeans.custom.DeploymentTarget.updateDeployments(DeploymentTarget.java:240)
          <     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
          <     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
          <     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
          <     at java.lang.reflect.Method.invoke(Method.java:324)
          <     at weblogic.management.internal.DynamicMBeanImpl.invokeLocally(DynamicMBeanImpl.java:711)
          <     at weblogic.management.internal.DynamicMBeanImpl.invoke(DynamicMBeanImpl.java:690)
          <     at weblogic.management.internal.ConfigurationMBeanImpl.invoke(ConfigurationMBeanImpl.java:476)
          <     at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:1557)
          <     at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:1525)
          <     at weblogic.management.internal.RemoteMBeanServerImpl.private_invoke(RemoteMBeanServerImpl.java:947)
          <     at weblogic.management.internal.RemoteMBeanServerImpl.invoke(RemoteMBeanServerImpl.java:908)
          <     at weblogic.management.internal.MBeanProxy.invoke(MBeanProxy.java:946)
          <     at weblogic.management.internal.MBeanProxy.invokeForCachingStub(MBeanProxy.java:481)
          <     at weblogic.management.configuration.ServerMBean_Stub.updateDeployments(ServerMBean_Stub.java:7271)
          <     at weblogic.management.deploy.slave.SlaveDeployer.updateServerDeployments(SlaveDeployer.java:1210)
          <     at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.java:362)
          <     at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resume(DeploymentManagerServerLifeCycleImpl.java:229)
          <     at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
          <     at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:964)
          <     at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:359)
          <     at weblogic.Server.main(Server.java:32)


          It appears that WebLogic 8.1 does not have the "user transactions enabled" flag
          for a connection factory. I see references to this flag in earlier versions of
          WebLogic. The closest thing in WL 8.1 seems to be the "XA Connection Factory Enabled"
          flag.
          Tom Barnes <[email protected]> wrote:
          >Actually, all you normally need to check is "user transactions enabled".
          >The XA versions of the javax.jms interfaces (which are generated
          >via XA connection factories) are not required - except
          >that I think that MDBs make a check for this.
          >
          >Naresh Bhatia wrote:
          >> So I assume that the XA capability is enabled by checking the "XA Connection
          >Factory
          >> Enabled" checkbox for the JMS connection factory.
          >>
          >> Thanks.
          >> Naresh
          >>
          >> Tom Barnes <[email protected]> wrote:
          >>
          >>>Just use a non-XA driver and non-XA pool for JMS JDBC stores.
          >>>WL JMS' XA capability does not come from its JDBC driver.
          >>>
          >>>Naresh Bhatia wrote:
          >>>
          >>>
          >>>>I am trying to set up a JDBC Strore for a JMS Server. The JDBC Store
          >>>
          >>>uses the Oracle
          >>>
          >>>>XA driver (oracle.jdbc.xa.client.OracleXADataSource). However whaen
          >>>
          >>>the JMS server
          >>>
          >>>>starts it gives me the following exception: Weblogic Pool Driver doesn't
          >>>
          >>>support
          >>>
          >>>>XA driver. Any idea what I am doing wrong? I am using WL 8.1 SP2.
          >THe
          >>>
          >>>full error
          >>>
          >>>>trace is shown below:
          >>>>
          >>>><Jan 15, 2004 3:05:09 PM EST> <Alert> <JMS> <BEA-040052> <JMSServer
          >>>
          >>>"jmsTestJmsServer1"
          >>>
          >>>>store failed to open java.io.IOException: JMS JDBC store, connection
          >>>
          >>>pool = <jmsTestJdbcConnectionPool>,
          >>>
          >>>>prefix = <JMS1>: cannot determine DBMS type
          >>>><java.sql.SQLException: Pool connect failed : java.lang.Exception:
          >>>
          >>>Weblogic Pool
          >>>
          >>>>Driver doesn't support XA driver, Please change your config to use
          >>>
          >>>a Non-XA driver
          >>>
          >>>><     at weblogic.jdbc.common.internal.JDBCUtil.wrapAndThrowResourceException(JDBCUtil.java:160)
          >>>><     at weblogic.jdbc.pool.Driver.connect(Driver.java:156)
          >>>><     at weblogic.jms.store.JDBCIOStream.checkDbmsType(JDBCIOStream.java:1490)
          >>>><     at weblogic.jms.store.JDBCIOStream.open(JDBCIOStream.java:420)
          >>>><     at weblogic.jms.store.JMSStore.open(JMSStore.java:224)
          >>>><     at weblogic.jms.backend.BEStore.open(BEStore.java:262)
          >>>><     at weblogic.jms.backend.BEStore.start(BEStore.java:151)
          >>>><     at weblogic.jms.backend.BackEnd.openStores(BackEnd.java:1171)
          >>>><     at weblogic.jms.backend.BackEnd.resume(BackEnd.java:1290)
          >>>><     at weblogic.jms.JMSService.addJMSServer(JMSService.java:2241)
          >>>><     at weblogic.jms.JMSService.addDeployment(JMSService.java:2012)
          >>>><     at weblogic.management.mbeans.custom.DeploymentTarget.addDeployment(DeploymentTarget.java:330)
          >>>><     at weblogic.management.mbeans.custom.DeploymentTarget.addDeployments(DeploymentTarget.java:590)
          >>>><     at weblogic.management.mbeans.custom.DeploymentTarget.updateServerDeployments(DeploymentTarget.java:568)
          >>>><     at weblogic.management.mbeans.custom.DeploymentTarget.updateDeployments(DeploymentTarget.java:240)
          >>>><     at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)
          >>>><     at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:39)
          >>>><     at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:25)
          >>>><     at java.lang.reflect.Method.invoke(Method.java:324)
          >>>><     at weblogic.management.internal.DynamicMBeanImpl.invokeLocally(DynamicMBeanImpl.java:711)
          >>>><     at weblogic.management.internal.DynamicMBeanImpl.invoke(DynamicMBeanImpl.java:690)
          >>>><     at weblogic.management.internal.ConfigurationMBeanImpl.invoke(ConfigurationMBeanImpl.java:476)
          >>>><     at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:1557)
          >>>><     at com.sun.management.jmx.MBeanServerImpl.invoke(MBeanServerImpl.java:1525)
          >>>><     at weblogic.management.internal.RemoteMBeanServerImpl.private_invoke(RemoteMBeanServerImpl.java:947)
          >>>><     at weblogic.management.internal.RemoteMBeanServerImpl.invoke(RemoteMBeanServerImpl.java:908)
          >>>><     at weblogic.management.internal.MBeanProxy.invoke(MBeanProxy.java:946)
          >>>><     at weblogic.management.internal.MBeanProxy.invokeForCachingStub(MBeanProxy.java:481)
          >>>><     at weblogic.management.configuration.ServerMBean_Stub.updateDeployments(ServerMBean_Stub.java:7271)
          >>>><     at weblogic.management.deploy.slave.SlaveDeployer.updateServerDeployments(SlaveDeployer.java:1210)
          >>>><     at weblogic.management.deploy.slave.SlaveDeployer.resume(SlaveDeployer.java:362)
          >>>><     at weblogic.management.deploy.DeploymentManagerServerLifeCycleImpl.resume(DeploymentManagerServerLifeCycleImpl.java:229)
          >>>><     at weblogic.t3.srvr.SubsystemManager.resume(SubsystemManager.java:131)
          >>>><     at weblogic.t3.srvr.T3Srvr.resume(T3Srvr.java:964)
          >>>><     at weblogic.t3.srvr.T3Srvr.run(T3Srvr.java:359)
          >>>><     at weblogic.Server.main(Server.java:32)
          >>>>
          >>>
          >>
          >

Error in allInOne.js: Object doesn't support this property or method

We are having an issue deploy our website (Developed in .Net) on a specific server. When we try to visualize a report on any browser we get this error:
Webpage error details
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Windows NT 6.0; Trident/4.0; SLCC1; .NET CLR 2.0.50727; .NET CLR 3.5.21022; .NET CLR 3.5.30729; .NET CLR 3.0.30618; OfficeLiveConnector.1.4; OfficeLivePatch.0.0)
Timestamp: Wed, 7 Apr 2010 17:52:31 UTC
Message: Object doesn't support this property or method
Line: 10
Char: 281690
Code: 0
URI: http://{IP ADDRESS}/WebUserInterface/aspnet_client/system_web/2_0_50727/crystalreportviewers12/allInOne.js
We have install the Crystal reports 2008 runtime and the Crystal report 2008 sp2.5 runtime. Both of them give me the same results.
It's killing me because i have installed the same solution on many other server without any issue.
Ben
P.s. The Web server is a Window Server 2003 R2 standard edition

Perhaps using [modules|https://smpdl.sap-ag.de/~sapidp/012002523100006252802008E/modules.zip] will at least tell us what dlls are loading. Look at the CR dlls. There should not be any v11 files loaded by your app.
You may also start considering obtaining phone support for this one. I have a feeling this will take more than just forums to solve...
Phone support can be obtained here:
http://store.businessobjects.com/store/bobjamer/DisplayProductByTypePage&parentCategoryID=&categoryID=11522300
Ludek

HP Photosmart 6520 Server Connection Error: -1: Apps don't work and Scan to email doesn't work

My HP PhotoSmart 6520 has a persistent error to connect to the server and therefore Apps and Scan to email doesn't work.
I have manually set DNS to 8.8.8.8 / 8.8.4.4, I have installed latest driver on my Macbook pro, I have updated firmware, but still not working. Weird is also that in my ePrintCenter, the Apps I see there are not in line with thos visible on the printer.
Detail is that I have set up the printer on a Windows PC but recently changed to Mac.
Printing, scan to Computer all works fine.
Help! I have read a lot on forums but so far no solution for me!

Hi Jack6520,
Welcome to the HP Support Forums. I see that you are unable to connect to the apps and use the scan to email feature of your Photosmart 6520 printer due to a server connection error.
First off, thank you for the very detailed information, I really appreciate it.
To better assist you, would you please provide some additional information:
When you set the manual DNS servers, did you also set a manual IP address for the printer?
Have you changed routers or internet service providers recently? Have you updated the firmware on the router? If you have an ISP-provided router, do you know if they pushed out a firmware update?
Have you recently installed any new anti-virus/malware software? If so it may have blocked the ports the printer uses to communicate. I’ve included a post by VisionAiry titled “Check the Anti-Virus for Blocked Ports and Timed Scans”.
Do you have a guest network setup? Please Print a Network Configuration page. It will let you know how many networks the printer sees. A guest network will have the same name as your network with a tag about it being the guest network.
Previously did you customize the printer’s ePrint email address? I’m asking this because I might ask you to disable then enable the web services. If we have to take this step you will lose the customized ePrint email address without any ability to get it back.
What version of Mac OS X are you using? whatsmyos.com
Are there any cables other than the power cable connected to the printer?
Thank you.
Regards,
Happytohelp01
Please click on the Thumbs Up on the right to say “Thanks” for helping!
Please click “Accept as Solution ” on the post that solves your issue to help others find the solution.
I work on behalf of HP

2011 MacBook Pro, 64 bit i7 quad core, upgraded to Lion OSx, Bootcamp installed with Windows 7, wanting to install Windows 8 (don't ask), tried downloading/installing bootcamp 5.0.5033, error message something similar to bootcamp doesn't support this Win

2011 MacBook Pro, 64 bit i7 quad core, upgraded to Lion OSx, Bootcamp installed with Windows 7, wanting to install Windows 8 (don't ask), tried downloading/installing bootcamp 5.0.5033 (both on the mac/windows partitions (actually using a parallel to run Windows)), error message something similar to bootcamp doesn't support this Windows
So the question is am I doing something wrong? Should I just try and install windows 8 through my windows 7 partition and see if I can use the bootcamp 5.05033. Or do I solely have to use the bootcamp to install Windows 8? I'm not too familiar with bootcamp and how it runs.

if you're using parallels and full bootcamp then you're making it 100% more troublesome for youself then it needs to be
bootcamp is running windows directly on the hardware this give full memory and cpu and 3d video game power
running windows in parallels is running a virtual machine where one can't run powerful games and the like but one can have it in a window and change fast between osx and windows
parallels as the only virutal machine (as far as I know) support not have the operating system as a file on the osx harddisk but can access a bootcamp parition as virtual machine but without the benefits bootcamps provides
it's a service parallels provide for those who want both to play games in normal bootcamp and sometimes use windows in a virutal machine
just install it like a normal virtual machine and you need not worry about bootcamp drivers and the likes
plus it would mean that the windows part would be a part of the timemachine bacup of osx
which it is not when it's in bootcamp

Python script to parse 'iwlist scan' into a table

Hi,
I've written a small python script that parses the output of the command "iwlist interface scan" into a table.
Why ?
Like many arch linux users I think, I use netcfg instead of something like network manager or wicd. So the most natural way to scan for wifi networks in range is iwlist scan. But the output of this command is huge and I find it difficult to retrieve information. So this script parses it into a table : one network, one line.
Example output
Name Address Quality Channel Encryption
wifi_1 01:23:45:67:89:AB 100 % 11 WPA v.1
wifi_2 01:23:45:67:89:AC 76 % 11 WEP
wifi_3 01:23:45:67:89:AD 51 % 11 Open
wifi_4 01:23:45:67:89:AE 50 % 11 WPA v.1
wifi_5 01:23:45:67:89:AF 43 % 4 Open
wifi_6 01:23:45:67:89:AG 43 % 4 WPA v.1
Details
It reads from stdin so you use it like that: iwlist wlan0 scan | iwlistparse.py
The width of the columns is determined by what's in it.
You can easily do a bit more than just parsing the info: in the example above, the quality has been calculated to percents from a ratio (e.g. 46/70).
It is sorted, too.
Customization
It's python so it's easy to customize. See the comments in the code.
Code
#!/usr/bin/env python
# iwlistparse.py
# Hugo Chargois - 17 jan. 2010 - v.0.1
# Parses the output of iwlist scan into a table
import sys
# You can add or change the functions to parse the properties of each AP (cell)
# below. They take one argument, the bunch of text describing one cell in iwlist
# scan and return a property of that cell.
def get_name(cell):
return matching_line(cell,"ESSID:")[1:-1]
def get_quality(cell):
quality = matching_line(cell,"Quality=").split()[0].split('/')
return str(int(round(float(quality[0]) / float(quality[1]) * 100))).rjust(3) + " %"
def get_channel(cell):
return matching_line(cell,"Channel:")
def get_encryption(cell):
enc=""
if matching_line(cell,"Encryption key:") == "off":
enc="Open"
else:
for line in cell:
matching = match(line,"IE:")
if matching!=None:
wpa=match(matching,"WPA Version ")
if wpa!=None:
enc="WPA v."+wpa
if enc=="":
enc="WEP"
return enc
def get_address(cell):
return matching_line(cell,"Address: ")
# Here's a dictionary of rules that will be applied to the description of each
# cell. The key will be the name of the column in the table. The value is a
# function defined above.
rules={"Name":get_name,
"Quality":get_quality,
"Channel":get_channel,
"Encryption":get_encryption,
"Address":get_address,
# Here you can choose the way of sorting the table. sortby should be a key of
# the dictionary rules.
def sort_cells(cells):
sortby = "Quality"
reverse = True
cells.sort(None, lambda el:el[sortby], reverse)
# You can choose which columns to display here, and most importantly in what order. Of
# course, they must exist as keys in the dict rules.
columns=["Name","Address","Quality","Channel","Encryption"]
# Below here goes the boring stuff. You shouldn't have to edit anything below
# this point
def matching_line(lines, keyword):
"""Returns the first matching line in a list of lines. See match()"""
for line in lines:
matching=match(line,keyword)
if matching!=None:
return matching
return None
def match(line,keyword):
"""If the first part of line (modulo blanks) matches keyword,
returns the end of that line. Otherwise returns None"""
line=line.lstrip()
length=len(keyword)
if line[:length] == keyword:
return line[length:]
else:
return None
def parse_cell(cell):
"""Applies the rules to the bunch of text describing a cell and returns the
corresponding dictionary"""
parsed_cell={}
for key in rules:
rule=rules[key]
parsed_cell.update({key:rule(cell)})
return parsed_cell
def print_table(table):
widths=map(max,map(lambda l:map(len,l),zip(*table))) #functional magic
justified_table = []
for line in table:
justified_line=[]
for i,el in enumerate(line):
justified_line.append(el.ljust(widths[i]+2))
justified_table.append(justified_line)
for line in justified_table:
for el in line:
print el,
print
def print_cells(cells):
table=[columns]
for cell in cells:
cell_properties=[]
for column in columns:
cell_properties.append(cell[column])
table.append(cell_properties)
print_table(table)
def main():
"""Pretty prints the output of iwlist scan into a table"""
cells=[[]]
parsed_cells=[]
for line in sys.stdin:
cell_line = match(line,"Cell ")
if cell_line != None:
cells.append([])
line = cell_line[-27:]
cells[-1].append(line.rstrip())
cells=cells[1:]
for cell in cells:
parsed_cells.append(parse_cell(cell))
sort_cells(parsed_cells)
print_cells(parsed_cells)
main()
I hope you find it useful. Please report bugs, I haven't tested it a lot. You may have to customize it though, because I think not all iwlist scan outputs are the same. Again, see comments, it should be easy.

This tool is very helpfull. I am trying to add a new function to the existing code to parse the signal level parameter from the output of iwlist wlan0 scan, but I am getting lot of issues .Since I am new to python script can anyone help me to extract the signal level also from the scan put put.
The parametr to be used is Signal level=-44 dBm ,I am trying to create a one more column with Signal level and print its out in the table.
Example:-
Signal level
-44db
The error I am getting
File "iwlist_parser_Testing.py", line 146, in <module>
main()
File "iwlist_parser_Testing.py", line 144, in main
print_cells(parsed_cells)
File "iwlist_parser_Testing.py", line 123, in print_cells
print_table(table)
File "iwlist_parser_Testing.py", line 102, in print_table
widths=map(max,map(lambda l:map(len,l),zip(*table))) #functional magic
File "iwlist_parser_Testing.py", line 102, in <lambda>
widths=map(max,map(lambda l:map(len,l),zip(*table))) #functional magic
TypeError: object of type 'NoneType' has no len()
Could some pls help me to solve this issue
Thanks

HDMI doesn't support HDPC

I have been renting movies for about 2 weeks now with no problems. Today I rented/downloaded August Rush and it will not play. I got the message HDMI doesn't support HDCP. What gives? I don't have a Component Video Cable. Is it necessary or is there a gliche?

Saw this on another forum and worked for me when I had same problem.
try:
1) turn off TV
2) unplug AppleTV electrical outlet (only way to turn off)
3) unplug both ends of HDMI cable
4) plug it all back in
Should only have to do this on rare occassions such as in my case of doing AppleTV factory reset. Not completely sure why, but it worked. I guess it made AppleTV's HDMI port reset and rescan for HDCP-supported connections.

RV120W WAN interface doesn't automatically re-enable after WAN connection is restored

I found that RV120W WAN interface doesn't automatically re-enable after a cable pull and re-plug. I have to go into the Status->System Summary and click the "Enable" button. Is this normal on this router? Can I prevent that from happening? I would hope this is NOT normal as this would mean that I would have to be on-site and login to the web interface to re-enable it after a power failure or WAN link loss.

Tekliu,
Thanks for the response. But, as I mentioned in my prior post, this is, unfortunately, the designed behavior for this device, at least with a static IP and no ISP login. Cisco Small Business Customer Support was clear on this and didn't even open a ticket. I asked that they submit a feature request to change this behavior in a future release. Of course, they couldn't make any promises.
One possible source of confusion is the different circumstances that can occur. In my testing, the interface does come back up automatically on a soft reboot. It also comes back up automatically if both the RV120W and the upstream (WAN) device are power cycled together. I believe this is because the upstream device comes up much faster and is up before the RV120W. The case we are talking about is when the upstream device is cycled or the cable is pulled while the RV120W stays up. In this case, the WAN port remains disabled until you manually select the button on the status page.
Thanks again for following up on this.

I have cs5 and when I try to download a raw file from my Nikon 810 an error message says this versioln of raw doesn't support this camera model. Yet I just updated cs5 online.

I have CS5 and when I try to download a raw file from my Nikon 810 I get an error message saying this version of raw doesn't support this camera model. Yet I just updated CS5 online.

I do not use lightroom and I have a subscription so I can open all supported RAW formats. You will need DNG file for Your Camera's NEF files for use in Photoshop ACR version. You can open your NEF files in LR it seems so you could do all your raw conversion with Lightroom and save out Tiff files for processing in Photoshop. I do use lightroom for I do not need its library. Lightroom does not support layered files so lightroom is of no value to me. ACR UI is all I need having a second interface to Adobe Raw Conversion Engine would more annoyance than value to me.

Iwlwifi-3945-ucode -- iwlist scan and Wlan LED not working

I am using the iwlwifi-3945-ucode driver to access wireless networks. I can connect to my WPA encrypted wireless LAN using netcfg; however, I cannot scan for any wireless networks around me using 'iwlist scan' or 'iwlist wlan0 scan'. It yields 'no scan results'. 'iwlist scanning' results in one entry showing me the wireless LAN I am connected to.
How can I get iwlist scan to work?
Also, I would like to get a feedback from the wireless LED of my notebook (Thinkpad X60s) telling me if there is anything going on with it.... I used to use thinkpad_acpi earlier, but this doesn't seem to help anymore (not sure if thinkpad_acpi was actually providing this option).
Any ideas how to enable it?
I would really appreciate any help!

shining wrote:
Stalafin wrote:
I am using the iwlwifi-3945-ucode driver to access wireless networks. I can connect to my WPA encrypted wireless LAN using netcfg; however, I cannot scan for any wireless networks around me using 'iwlist scan' or 'iwlist wlan0 scan'. It yields 'no scan results'. 'iwlist scanning' results in one entry showing me the wireless LAN I am connected to.
How can I get iwlist scan to work?
Maybe try as root.
Yeah, root does the trick. Has been changed then, hasn't it? Don't remember to have used root for that one, ever.
shining wrote:
Also, I would like to get a feedback from the wireless LED of my notebook (Thinkpad X60s) telling me if there is anything going on with it.... I used to use thinkpad_acpi earlier, but this doesn't seem to help anymore (not sure if thinkpad_acpi was actually providing this option).
Any ideas how to enable it?
I think you have to wait for 2.6.26, but it should not be too far away.
They have taken that one out? See, I had it working about one month ago. Then I decided to set up Arch anew (like two weeks ago, followed by note turning the notebook on for about another week), and now there isn't happening anything. So since the new setup it doesn't work. I am just figuring if I have to modprobe something. Gonna restart now... maybe it helps.

Iv'e got this error message : "protocol doesn't support output"

When i execute my applet the part of code below give's me thi error message: "protocol doesn't support output". This part of the code save's a vector(of string) into a data file. I'm able to load the file but i can't put info in it. Helppppppppp:
That's the method where tje problem is :
private void saveVector()
Evenement Ev;
try{
// THE ERROR IS PROBABLY IN THE 2 NEXT LINES!
Dos = new DataOutputStream(new BufferedOutputStream( new URL(this.getCodeBase(), FichierEvenement).openConnection().getOutputStream()));
for ( int i = 0; i <= VecEvenement.size();i++ )
Ev = (Evenement) VecEvenement.elementAt(i);
String Ligne = Ev.getDateEvent().trim().concat("|")+ Ev.getTitre().trim().concat("|") + Ev.getLieu().trim().concat("|") + Ev.getDesc().trim().concat("|") + Ev.getPers().trim().concat("|")+ Ev.getAdresse().trim().concat("|");
Dos.writeUTF(Ligne);
Dos.close();
catch (Exception e) {
LErr.setText(e.getMessage());
}

http://java.sun.com/docs/books/tutorial/networking/urls/readingWriting.html
As is noted in this part of the tutorial, a URL may simply not support output:
"Next, the program creates the URL object--the URL for the backwards script on java.sun.com--opens a URLConnection, and sets the connection so that it can write to it:
URL url = new URL("http://java.sun.com/cgi-bin/backwards");
URLConnection c = url.openConnection();
c.setDoOutput(true);
The program then creates an output stream on the connection and opens a PrintWriter on it:
PrintWriter out = new PrintWriter(c.getOutputStream());
If the URL does not support output, getOutputStream method throws an UnknownServiceException. If the URL does support output, then this method returns an output stream that is connected to the standard input stream of the URL on the server side--the client's output is the server's input. "
Sorry I can't be of more help.

TS3408 I keep on getting this error message on my Yahoo and Safari You're almost there, but your web browser doesn't support the newest version of Yahoo! Mail

I keep on getting this error message on my Yahoo and Safari all of a sudden;
You're almost there, but your web browser doesn’t support the newest version of Yahoo! Mail
The links it gives to upgrade don't work !
I have Safari Version 5.1.7 the latest for Snow Leapord. I get the same error message on Firefox and Google Crome aI even dowmloaded another Brower for Mac still got he same error message ! I have used the Disk Utility to rparir files and rest Safari. I have deleated Firefox then downloaded a fresh version, still the same error messages ! Please help it's driving me nutts.

Perky --
You do not need any "Cleaner" app for Macs. I would not be at all surprised if that didn't actually damage your Mac, especially if it were MacDefender. Applejack is OK, but I'm not sure what it erased. Do you know?
You also don't need any Virus Barrier. That could also mess things up.
The fact that all of your browsers are now messed up indicates that it is not a Safari problem, but more system-wide.
Did you check here?
http://help.yahoo.com/l/us/yahoo/mail/yahoomail/technical/

I keep on getting this error message on my Yahoo mail. You're almost there, but your web browser doesn't support the newest version of Yahoo! Mail

I keep on getting this error message on my Yahoo mail all of a sudden;
You're almost there, but your web browser doesn’t support the newest version of Yahoo! Mail
The links it gives to upgrade are blocked
I have latest version of FireFox 19 and Snow Leopard. I get the same error message on Safari and Google Crome aI even downloaded another Browser for Mac still got he same error message ! I have used the Disk Utility to repair files and rest Safari. I have deleted Firefox then downloaded a fresh version, still the same error messages ! Please help it's driving me nuts.

You can check for problems caused by a possibly corrupted user agent.
See:
*https://support.mozilla.org/kb/Finding+your+Firefox+version
*https://support.mozilla.org/kb/websites-say-firefox-outdated-or-incompatible
*http://kb.mozillazine.org/Resetting_your_useragent_string_to_its_compiled-in_default

Iwlist scanning gives: Interface doesn't support sc [solved]

Similar Messages

Maybe you are looking for