Lenovo G570 - Stays on Lenovo start up screen, then powers off

Lenovo G570
Model 4334
Hi
Whenever i switch on my laptop it stays on the Lenovo start up screen for about 30 seconds, and then powers off. During the 30 seconds the laptop fans runs louder than usual but nothing else happens.
Ocassionally it does get past that stage but then takes a long time on the 'starting windows' screen.
I've used the onekey recovery to return it to my backup and even returned it to the factory settings but the problem persists.
I'm unsure of what to next and how the problem can be solved. Any Suggestions?
Thanks.

try to load safe mode when you see lenovo logo at start-up. ( f8 )
if it works, press f8 again to load "last known good configuration"
otherwise, check your ram sticks ( remove/replace/swap ) and check if your hdd is working properly.
do you have any heating issue by the way? did you make changes recently?

Similar Messages

Macbook pro wont start. grey screen then shuts off

I have been having some problems with my macbook when my battery would die and i would plug it in and try to turn it back on it would take forever to start back up. Sometimes i woudl have to unplug, take out the battery then put them back in and zap the pram and it would start. Then today it just started taking forever to restart so i shut it down and tried to restart now it starts goes to the grey screen and the little thing starts spinning and then about 5 sedc later it shuts itself down.
PLEASE HELP

If the Apple Hardware test does not bring up any problems with the hardware, I would advise doing an archive and install before you zero out the drive and erase all of the data on it.
Some things to keep in mind:
If your computer shuts down while booted to the install disk (either the AHT or the installer) you're looking at a hardware problem.
If you need to erase and install or send it in for repair of a hardware problem, you will need to back up any data you do not want to lose before doing so. If you are unable to do backups, an apple store or authorized service provider can do data retrieval for you. Bear in mind this is an optional service and you would be charged a fee for data retrieval.

I bought Football Manager 2015 but when it downloaded and I went to open it, it stays on home screen then cuts off, any advice?

I bought Football Manager 2015 but when it downloaded and I went to open it, it stays on home screen then cuts off, any advice?

Basics from the manual are restart, reset, restore.
You can also try removing and reinstalling the app

Installed mavericks - restarted, but didn't finish iphoto update - force quit - restart gray screen stall, powers off - safe mode says disk full - recovery mode says mac and recovery HDs locked - verify disk says recovery ok - repair says no live support?

Installed Mavericks - restarted, but didn't finish iphoto update - force quit - restart gray screen stall, powers off - safe mode says disk full -recovery mode says mac and receovery HDs locked - verify disk says - recovery ok - repair says no live support?

When you see a beachball cursor or the slowness is especially bad, note the exact time: hour, minute, second.
These instructions must be carried out as an administrator. If you have only one user account, you are the administrator.
Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad and start typing the name.
The title of the Console window should be All Messages. If it isn't, select
          SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
          View ▹ Show Log List
from the menu bar at the top of the screen.
Each message in the log begins with the date and time when it was entered. Scroll back to the time you noted above.
Select the messages entered from then until the end of the episode, or until they start to repeat, whichever comes first.
Copy the messages to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of it useless for solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

Torch Wont Start, loads partway then shuts off or resets.

My Torch 9800 was recently went for a swim in rainwater. At first I didn't realize the phone was water damaged, and thought it has just randomly turned off, so I took the battery out, put it back it, and then it started making a static sound. So I immediately removed the battery and put the phone in rice. Unfortunitely got my time lines mixed up and tried to put the battery back in too soon and again the phone started making a static sound. So I took the battery back out, and put it back in rice worried that I'd fryed all the circuits. However, 48 hours later I put the battery back in and the loading screen came up, but when it went to the rogers screen pre-my wallpaper the phone reset and started to load again, then it shut off. Everytime I do a battery pull the led light comes on for a couple seconds, and then it shuts off and nothing happens. So I took the sim card out, and tried the batter again and the phone started to load then shut off.
I've found that If I leave the battery out for a while the phone will start to load, but either gets stuck at the 2/3 mark and will freeze there, or it'll shut off. Today I tried putting the battery back in, and the phone loaded to my home-screen, but then froze and shut off.
If I plug my phone into my computer through the USB the phone connects for a second, and then disconnects. I've tried with both the battery in and out.
I've also tried re-installing the OS through the loader app as mentioned (http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry), and through a force connect with desktop manager (by hitting update button when desktop manager tries to connect with my phone when I first plug it in to my computer, before it resets and disconnects). Both times the phone starts to load the OS, but when it comes to re-initialize the phone, it'll disconnect, then reconnect, but then after 4-5 seconds dissconnect again, and so I get the "Application Loader was unable to connect with your device" error while the loader is trying to recconect to JVM...
Is there any hope for my phone? I love my torch and was realllly hoping to hold out until Blackberry releases their new phones in the new year.
I think I might try soaking the phone in 99% isopropanol in hopes in might be just some mineral build up from the rain water.
But I'd really appreciate any suggestions anyone has to help me try and get my phone working again.
Thank you.

Hello...and apologies for the delayed reply!
Hopefully you already have resolved this...but just in case...
Applying power to your BB between it getting wet and doing the proper process (including the maximum waiting time) reduces the chances of success. Further, the only thing predictable about moisture intrusion into a BB (indeed, any electronic device) is that the results will be unpredictable. I've seen some come back up right away and be fine. I've seen others never work at all. I've seen still others run for a bit, and then die later. And every thing in between.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

What do i do if my ipod touch keeps going to the charge screen, then to the apple screen, then shuts off?, what do i do if my ipod touch keeps going to the charge screen, then to the apple screen, then shuts off?

what do i do if my ipod touch keeps turning on, going to the charge screen, then going to the apple screen, then shutting off?

If it is still charging using the adapter, let it stay there for at least 15min, then connect again, if necessary use recovery mode. iOS: Unable to update or restore
If still not luck, and the battery still shows the red charging icon, you might need a new battery.

My iphone 5 died so I plugged it back in to charge and it will not turn on. It will turn to the screen with the apple logo and black screen then turn off again. Any suggestions?

My iphone 5 died so I plugged it back in to charge and it will not turn on. It will turn to the screen with the apple logo and black screen then turn off again. Any suggestions?

I leave it charging until it gets back to full, usually it turns on after a little bit of time after plugging it in, but all its doing is going to the apple logo screen and going blank again.

2006 Intel Mac mini starts to load then turns off and sometime a kernel panic warning will appear

Mac mini starts then powers off before loading osx and sometimes gives a kernel panic warning

Tough without the Install disc, but some things to try...
Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
/sbin/fsck -fy
Repeat until it shows no errors fixed.
(Space between fsck AND -fy important).

My mac book pro won't work. it starts up and then turns off

My mac book pro starts up & then turns off. I know the memory was almost full so I bought an external storage and was going to start removing pictures to make more room, but now it won't let me work on it. it just turns right off. It's not the battery. has anyone had this problem? thanks

Hello Marcela100
Check out the article below for troubleshooting startup issues on your Mac.
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
http://support.apple.com/kb/ts1417
Thanks for using Apple Support Communities.
Regards,
-Norm G.

MS-6743G (865GM2-LS) System Start & get boot then Auto-off, Unable to find prblm

Hi,
I have problem with my computer to start
MS-6743G (865GM2-LS) System Start & get boot then Auto-off,
every time start, the system boot, after Bios load, then turn-off
If press Del key, enter BIOS setup, also turn-off power
How to solve this problem, what is the problem?
Is't the motherboard problem?
Processor problem?
I can't find it?
Please anyone help me to solve this problem?
Thanks
PC Sekar

Hi
This is the specifications for my System
MSI 865GM2-LS(MS-6743G), Intel P4 2.80E 800MHz 1MB CPU
XP Pro w/SP2 all updates
Kingston KVR266X64C25/256
(512MB-64Mx64 DIMM, PC3200-DDR SDRAM -Exchanged the above one)
SAMSUNG CD-RW Driver SH-R522
Maxtor 120GB (6Y120M0STD) SATA, DiamondMax Plus 9
MITSUMI 1.44 Disk Drive, Model D359M3
HP7540 17" monitor
Please check it & help

My MacBook won't turn on ? It's on an updating screen then shuts off when I turn it back on the same things happens again over and over

My MacBook won't turn on ? It's on an updating screen then shuts off when I turn it back on the same things happens again over and over

On the bottom of your MBP is the serial number. Enter it here and post back the model/year information:
https://selfsolve.apple.com/agreementWarrantyDynamic.do
What OSX do you have installed?
Ciao.

Get start-up chime, gray screen, then shuts off

I have an eMac that will start up, but once the screen turns gray and the gear starts going around in a circle, it powers off. I tried to read some of the other posts.
1. I tried unplugging the cord from the computer for a while - no change.
2. I went into the open firmware and did those three commands - it stayed on long enough to do that and then when it restarted - no change
3. I did a cmd-option p+r, I forget what that is called, but... - no change
4. I hooked up my firewire drive and was able to boot from it. I was going to do a netrestore, but the HD was not in the list for target source. What does that mean?
I am a computer teacher new to Macs and any help is greatly appreciated.
eMac Mac OS X (10.3.9)

Strange; not that Disk Warrior was able to repair your hard drive --- it has an excellent reputation for that --- but that a damaged disk directory (which is what Disk Warrior repairs) would cause the Mac to shut down. The expected failure mode for a severely damaged disk directory would be to see it stuck at the grey startup screen (lesser directory damage can manifest as unvalidly large untrashable files; e.g., a 128 GB file on a 40 GB hard drive).
In your place I'd be working feverishly to make sure all my data is backed up (and verify the backups). Something's not right. If you open Disk Utility, what's shown for the SMART status of the drive?
Opening up the eMac to replace the hard drive is a non-trivial process and requires care, both to avoid the dangerous voltage levels on the CRT yoke and to avoid damaging the power button leads, and of course voids any remaining warrenty, but plenty of people have done so (try Googling "Apple eMac Upgrade Guide"). You can find internal hard drives from 40 GB to over 300 GB at prices from US$80 to $600 but figure somewhere in the $100 - $150 range for the drive.

MacBook Pro gets to start up screen then keeps restarting

I was using my MacBook Pro fine, and closed it as I normally do. I heard it making noises, so I took it back out and opened it. The screen was black and not turning on. I pressed the power off button to turn it off. When I pressed it on, it went to the gray start up screen as normal, but never loaded. The time waiting circle kept going round and round. After a few minutes of trying to load, the computer automatically restarted and the cycle started again. It did it a few more times before I turned it off and waited an hour. I tried it again and the same thing happened. Please tell me what happened and how to fix it. Thanks!

Eric
Thank you for taking the time to post those links to informative articles.
In relation to the first article entitled "Resolve startup issues and perform disk maintenance with Disk Utility and fsck"
I can confirm that i was not able to start in safe mode but was able to boot up in recovery mode and run disk utility. The only one i hadn't tried is fsck. Please correct me if I am wrong, but if from what I understand by the article, this is to be used if I could not run disk utility, with which I have been able to do and to repair both the disk and permissions. But again, if I've missed the obvious from that article please correct me.
Te second article entitled "Troubleshooting Startup and Login Items" identifies troubleshooting that should be carried out in safe mode. However I am unfortunately unable to start in safe mode and have not been able to progress past the apple logo since this problem started.
Thank you for both links and for taking the time to share. If though I have missed something more significant in this regard I would appreciate your feedback.
Many thanks

Blue screen when powering off

I recently purcahsed a one year old Lenovo 3000, it had Windows XP installed and I upgraded this to Windows Vista with no problems. I then renamed the laptop and deleted the previous owners user files and that's when I had a problem. When I power down the laptop I get a Blue Screen saying something about a dump and saying it was doing something to protect my PC ? I found some kind of fault finding log and it mentioned something about the pc's name and also something about being unable to access a certain user file. I changed the computer name back to the original one and unerased the original user file but I still get the Blue Screen when powering down.
Is it possible to get a replacement software DVD that will get me back to square one please, thanks for any help. Dan McLean in Port Glasgow.

This really sounds like shoddy drivers combined with an IRQ conflict.
I suggest you post your IRQ's from System Info, for example:
IRQ 0   System timer   OK
IRQ 1   Standard 101/102-Key or Microsoft Natural PS/2 Keyboard   OK
IRQ 4   Communications Port (COM1)   OK
IRQ 5   WinFast TV2000 XP WDM Audio Capture   OK
IRQ 6   Standard floppy disk controller   OK
IRQ 8   System CMOS/real time clock   OK
IRQ 9   Microsoft ACPI-Compliant System   OK
IRQ 11   NVIDIA nForce PCI System Management   OK
IRQ 12   Logitech-compatible Mouse PS/2   OK
IRQ 13   Numeric data processor   OK
IRQ 14   Primary IDE Channel   OK
IRQ 15   Secondary IDE Channel   OK
IRQ 16   RADEON X800 XT Platinum Edition   OK
IRQ 17   WinFast TV2000 XP WDM Video Capture   OK
IRQ 18   Creative SB Live! series   OK
IRQ 20   NVIDIA Network Bus Enumerator   OK
IRQ 21   Standard OpenHCD USB Host Controller   OK
IRQ 22   Standard OpenHCD USB Host Controller   OK
IRQ 23   Standard Enhanced PCI to USB Host Controller   OK
Also, as you intend to DL and install the nVidia Drivers make sure you get the sound drivers from Realtek Downloads too.
What Drivers are you using for the AIW?
Take all the Driver CD's and make pretty Christmas tree ornaments out of them
~Edit~ I just looked at the stop error again and realized I misread, then I saw Supershanks post My initial suspicion is likely to be wrong, but it's worthe a look anyway.

Mac book starts to boot, then turns off

I have Mac Book Pro (13", Yr2011) which will not boot. It has a 1TB HD which has been partitioned for Mt Lion (primary) and Snow Leopard. The computer has worked fine in this configuration. For about 6 wks, the computer was not used and apparently the battery charge depleted to zero. When an attempt was made to use the computer with battery only, the screen was just light gray with a circular wait icon. After several minutes with no change, the battery was noted to be discharged. A charger was connected, but there was no change in the screen. The computer was then turned off and left to fully charge. On first attempt to turn on, the computer did come to life. However, when attempting to Update software, it displayed No Internect connection - even though it was connected by ethernet. The computer was power cycled, however the screen then again only showed light gray with wait icon. Now when attempting to boot, the screen shows light gray, circular wait icon & horizontal bar graph indicating something is loading. After about several minutes, the bar graph fills & disappears, however, the screen remains light gray with wait icon - indefinitely. On a few attempts, the computer and screen simply turned off after about 30secs.
If I hold the Option key while powering on, then the Mac does boot ok to Snow Leopard. Apparently, the Mt Lion side of the HD was corrupted during the low battery boot appempt. The last time I backup MtLion was several months ago, so if I prefer not to reformat and reload from scratch.
Since the Mac did boot up once, I'm wondering if there is a way to recover without having to reformat and start again.
Don

Tough without the Install disc, but some things to try...
Does it boot to Single User Mode, CMD+s keys at bootup, if so try...
/sbin/fsck -fy
Repeat until it shows no errors fixed.
(Space between fsck AND -fy important).

Lenovo G570 - Stays on Lenovo start up screen, then powers off

Similar Messages

Maybe you are looking for