Linux app builder hangs with daqmxbase 1.5.0-f2

Having a problem building apps on linux using daqmxbase 1.5.
Test machines are:
A fresh installation of Suse 9.2 (kernel 2.6.8) on a Dell SC420 to which I added Labview 7.1, Appbuilder and daqmxbase 1.5.0-f2. Building our app fails on the "Copying files to application" part - the progress bar hangs at about 40% complete. The Labview windows become unresponsive, disk i/o stops and the process has to be killed.
I tried building some of the NI examples to pin down a possible issue with our vi but the same thing seems to happen with any example that has a daq component.
Normalize Waveform example - builds and runs fine
Signal generation and processing example - builds and runs fine
Our app - hangs
USB-6008/9 Interactive Control Panel - hangs
Count digital events buffered continuous ext clk example - hangs
In case there was an issue with Suse or 2.6.8 I tried a fresh install of Redhat 9 (2.4.20) on a different box, added labview, appbuilder, daqmxbase 1.5 and the same thing happens - the builder hangs.
Figuring that the builder might need some hardware in order to build an app properly I also gave it a shot with a USB 6009 plugged in - same result.
Being new to labview I'm unsure whether there are any specific log files I can provide that will help track down this problem - /var/log/messages has nothing.
Any ideas?

I've tried different kernels (the machines are P4 w/HT so the installer defauls to an smp kernel). Currently running linux 2.6.8-24.10-default #1 Wed Dec 22 11:54:27 UTC 2004 i686 i686 i386 GNU/Linux. I've tried various other smp and non-smp kernels.
I've uninstalled and reinstalled Labview, app builder and daqmxbase in various sequences. I've even reinstalled the entire Suse 9.2 OS and played with various grub and BIOS options. I've tried with the vanilla OS install and after applying the available patches through YaST.
I should point out that the app runs fine in Labview itself and compiles without errors on Windows.
There were no errors reported when installing Labview or daqmxbase and nothing in the system log.
I'm at a complete loss. The app builder fails every time, on different boxes, and it 100% reproducable.
I guess I'll give Mandriva 10 a try. In the meantime.... help! Message Edited by PaulSmith on 06-17-2005 11:52 AM
Message Edited by PaulSmith on 06-17-2005 11:52 AM

Similar Messages

Error 10, Duplicate path on building with Linux App Builder

I have used both Mac and Windows App Builder 6.1 with the same files and not had this kind of problem. The VIs I am trying to build are very simple, see attachedd.
Attachments:
Analog_Out_Control.vi ‏91 KB

I've tried different kernels (the machines are P4 w/HT so the installer defauls to an smp kernel). Currently running linux 2.6.8-24.10-default #1 Wed Dec 22 11:54:27 UTC 2004 i686 i686 i386 GNU/Linux. I've tried various other smp and non-smp kernels.
I've uninstalled and reinstalled Labview, app builder and daqmxbase in various sequences. I've even reinstalled the entire Suse 9.2 OS and played with various grub and BIOS options. I've tried with the vanilla OS install and after applying the available patches through YaST.
I should point out that the app runs fine in Labview itself and compiles without errors on Windows.
There were no errors reported when installing Labview or daqmxbase and nothing in the system log.
I'm at a complete loss. The app builder fails every time, on different boxes, and it 100% reproducable.
I guess I'll give Mandriva 10 a try. In the meantime.... help! Message Edited by PaulSmith on 06-17-2005 11:52 AM
Message Edited by PaulSmith on 06-17-2005 11:52 AM

App builder problem with Fuzzy Toolkit

Hi,
today I wanted to build an app (using LV2009) with some functions from "PID and Fuzzy Control Toolkit".
Now the app builder is searching for a type definition in vi.lib (as shown in the pic), but it doesn't find the CTL file - but the path used for searching is correct! Then I do the search manually, point to the requested CTL in the correct place (and with correct name of course), and the build will succeed.
What's up here?
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome
Solved!
Go to Solution.
Attachments:
check.png ‏18 KB

Hi,
thanks for your thoughts!
Answers:
- I use WinXP SP3, German settings
- I use LV2009SP1 for that project, toolkits are installed with that version (other LabVIEW versions are installed too, from LV8.5.1 to LV2010SP1)
- LabVIEW is installed in the "standard" path on drive C: (as can be seen on the attached pic of message #1)
- the app builder is unable to find the ctl file (the standard search dialog pops up), but the file is located on exactly the path used for searching (as can be seen on the picture)
- all I have to do (but this really annoys me) is to point LabVIEW to an item in a place it already knows...
- the type definition is part of the toolkit, it's installed/located in the standard folder of that toolkit, and I never changed/touched any path or file name
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

IOS Export Release Build hangs with FB4.7

I recently updated to FB4.7 running AIR 3.4 on my Macbook Air under Lion 10.7.5.
My project contains a large number of embeded files and when debugging under FB4.6 I was often encountering Java Heap Errors and lots of out of memory errors. However, I was able to put up with those errors and still export working release builds.
Under FB4.7 I am able to compile DEBUG builds now without the problems I was having under FB4.6. However, when I attempt to export an iOS release build using the IDE under FB4.7 the process always just hangs (at Packaging 0%) and never completes (even after waiting hours).
If I create a small test project under FB4.7, I am able to export a release build successfully. So I believe my FB install is working.
I've tried bumping up the xms and xmx settings in the Flash Builder 4.7.ini file to 2048m, but that has made no difference to the problem.
I suspect that the large number of embeded files that I have in my project may be contributing to the problem. The embeded files are primarily all UI artwork as my app supports all the different iOS screen resolutions.
Short of restructuring my entire project to remove all the embeded files (which I really do not want to do at this point) is there anything else that can be done to get FB4.7 to succesfully export an iOS release build?

Hi Sanjay,
Thanks for the quick reply! Hereby the extra info:
1. -Xmx2048m
2. We are using ATF files with all three textures included (around 14 MB for @2x and 8 MB for @1x). We could exclude the DXT and ETC ones, but than we need to create them for all separately. Thereby we are not done with the project so the size will still increase, than it is a solution for a short time.
3. I just tried with the following results:
At the beginning it is giving some warnings:
Exception in thread "main" com.adobe.air.ipa.ProcessError: Assembler failed
          at com.adobe.air.ipa.AOTCompiler.launchProcess(AOTCompiler.java:271)
          at com.adobe.air.ipa.AOTCompiler.compileModule(AOTCompiler.java:1444)
          at com.adobe.air.ipa.AOTCompiler.compileBitcodeImpl(AOTCompiler.java:1342)
          at com.adobe.air.ipa.ASMGenerator.main(ASMGenerator.java:68)
Exception in thread "main" com.adobe.air.ipa.ProcessError: Assembler failed
          at com.adobe.air.ipa.AOTCompiler.launchProcess(AOTCompiler.java:271)
          at com.adobe.air.ipa.AOTCompiler.compileModule(AOTCompiler.java:1444)
          at com.adobe.air.ipa.AOTCompiler.compileBitcodeImpl(AOTCompiler.java:1342)
          at com.adobe.air.ipa.ASMGenerator.main(ASMGenerator.java:68)
Undefined symbols for architecture armv7:
After that, a lot of lines are shown with this at the end:
ld: symbol(s) not found for architecture armv7
Compilation failed while executing : ld64
Any idea?
Thanks,
Ben

App Builder error with app icons

never seen this error before…
all the icon names are unique, I've always named then 29x29.png 512x512.png etc
I'm also only building this for iPad, so also confused about the iPhone ref. Anyone seen this error before??
Cheers
Alistair

Custom slot labels are the optional navigation buttons (such as "Store," "FAQ," etc.) that enterprise publishers can add to their apps. It's not related to the standard app icons.
Are you building an app using an Enterprise account? If not, there's a bug we'll need to look at. If so, check the Customized XML Strings (?) option in the advanced settings of the App Details pane. Delete or re-create the XML file.

App Store hangs (not responding)

I am trying to use the App Store to upgrade my iMac from Snow Leopard (10.6.8) to Mountain Lion (10.8). When I open the App Store and sign in using my Apple ID, I can click on the "OS X Mountain Lion" link. This shows a new page with a button that says $19.99. When I click that button, the button changes to "Buy App". When I click the Buy App button, the App Store hangs with the spinning ball icon after about 20 seconds. I left it alone for over 2 hours, and it remained hung. I have searched user forums and tried a few things. Nothing has worked. Here are some things I have tried, with no success.
+ turned off Spotlight (some forums mentioned that was an issue)
+ unplugged my external USB drive for Time Machine backups
+ re-booted into safe mode
+ removed all directories inside /var/folders
+ removed ~/Library/Preferences/com.apple.appstore.plist
+ removed ~/Library/Preferences/com.apple.storeagent.plist
+ removed ~/Library/Application\ Support/AppStore
+ removed ~/Library/Caches/com.apple.appstore
+ removed ~/Library/Caches/com.apple.storeagent
+ removed ~/Library/Caches/storeagent
I asked Apple support, and they said, "You must upgrade to Lion first, then Mountain Lion, but unfortunately Lion is not available for download. Please visit your local Apple store for help." So, I drove out to the nearest Apple store. The assistant there told me it is NOT necessary to upgrade to Lion first. They asked me to bring my iMac into the store to have a look.. what a hassle. So I replied back to Apple support, who then asked me to call their support number. I called, then hung up when they said "this call will cost you $20".
Anyone out there smart enough to solve this puzzle?

No, there is no direct download link. Those are days of the past, I'm afraid. You may need to reinstall Mavericks.
Install or Reinstall Yosemite, Mavericks, Mountain Lion, or Lion from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
How to Clean Install OS X Yosemite
OS X Mavericks- Erase and reinstall OS X
OS X Mountain Lion- Erase and reinstall OS X
OS X Lion- Erase and reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet if possible
because it is three times faster than wireless.

My "Hanging with Friends" app keeps crashing whenever I try to open it. I have deleted and re-downloaded the app, restarted my iPhone, and even restored my iPhone all together, and nothing is working. How can I get this app to work again?

My "Hanging with Friends" app keeps crashing whenever I try to open it. I have deleted and re-downloaded the app, restarted my iPhone, and even restored my iPhone all together, and nothing is working. How can I get this app to work again?

Can you start Firefox in [[Safe mode]] ?
You can also do a clean reinstall and download a fresh Firefox copy from http://www.mozilla.com/firefox/all.html and save the file to the desktop.
Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
You can initially skip the step to create a new profile, that may not necessary for this issue.
See http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

My executable compiled with Real Time Engine 5.1.1 in App Builder gives error when trying to run in App Builder with RTE 6.1

Hello. I built an executable using App Builder in LV 5.1.1 and now, years later, I am trying to run it in LV 6.1 but I get an error stating a requirement for Run Time Engine version 5.1.1. To be able to run this, must I install the older version of Run Time Engine? If so, where can I find the older version? Do I have to install the older version of LabVIEW to get the RTE? Will having both versions on my pc be a problem?
I assume that once I am able to run the exe, that I will be able to recompile with the newer version of the RTE using App Builder. Is this correct?
I have been away from LabVIEW for several years and am a bit rusty on these details that I once knew. Any help is appreciated.
Alex

The version of the run-time engine must match the version of LabVIEW that was used to create the executable. You can get any version of the run-time engine you want here. The only way to create a version 6.1 exe is to re-build it from the source code with diagrams. An exe has no block diagram so it cannot be converted to a newer version.

Flash Builder 4 with Flex SDK 4.0 for Intel App Up

There is some misinformation on Intel AppUp and the Melrose FAQ about being able to publish with Flash Builder 4.
Intel App Up Program Submission
According to http://appdeveloper.intel.com/en-us/article/adobe-air-packaging-guide-atom-developer-progr am-submissions
"AIR app must be built using Flex Builder 3 with Flex SDK 3.5a. Currently Flex Builder 4 with Flex SDK 4 is not supported."
Melrose FAQ
According to http://learn.adobe.com/wiki/display/melrose/Melrose+Developer+FAQ
"Q: Are there system requirements for enabling try and buy in AIR apps using Melrose?
A: You must have Adobe Flex Builder 3 or greater and Adobe AIR 1.5.3 or greater."
Is the Intel App Up statement correct? If it is, could I get an explanation why? I've been waiting for the last 3 months waiting for the Melrose SDK to deploy to Intel App Up and now I can't even submit my application.
Thanks.

The current version of Melrose supports Flex 3.5 SDK for AIR applications running on AIR 1.5.3 runtime or higher. You can use Adobe Flex Builder 3 with Flex 3.5 SDK or Adobe Flash Builder 4 with Flex 3.5 SDK.
Support for Flex 4.1 SDK for AIR applications running on AIR 2.0 runtime should be available within a few weeks. Please note that we will not be able to support Flex 4.0 SDK because of certain technical challenges.

Signing failed issue with app builder

"Message was edited by: bicknell1 Ok well I kept trying and the App Builder finally launched, but still have the same problem of 'Signing failed, please try again' for the digital signature at the end of the process. Even though it failed, it put an .ipa on the desktop, but when launched in iTunes its only 15.7mb when it should be around 180mb which tells me that the Folio is not loading into the App Builder properly. Please advise. Thx"
I have the same problem, I tried to recreate the certificates and provisioning files that look good, then I tried to change the version and republish the app (from v25 to v24) but nothing.
Can you contact me Neil? So I send you the log files ( but I don't know how to create them).
Thank you in advance for the help

Neil thanks for the link,
I am a member Creative Cloud Single Edition, I had an article entitled,
I put a title When updating and tried again but nothing.
Certificates are valid from the keychain because I have both the public and private key associated with the certificate inside the private key.
I have no articles with the name "cover_h" or "cover_v."
I updated the java for mac os x version 10.7.5.
But no, I always error.
I do not know what to feel.
Do you have other useful links for finding the cause of the error?
Thank you in advance for the help.

Creating app for Android/Kindle with App builder and Single Edition (No professional or Enterprise)

Hi there,
I know there is no official support for Android in Single Edition, but, once you have installed Indesing CC and App Builder in a mac, and you create app from your Folio menu, is it possible to create then an Android/Kindle apk app for publishing by your own?
Has anybody published sucessfully in this way?
Other point, is that I suposse that you need a Professional or Enterprise licence to create an android app from the Web-enablet App Builder. Cause I can't find the way the make my single account to join the role to this function (And app builder website website just tells me I have to do this, as if I were able to do it with my license...).
By the way, I think Adobe should explain more clearly this points. There is too much documentation, but difficult to find this answers... And a lot of people with the same troubles...
Thanks!

Thanks Tomek!
So, can you confirm if you join the Professional edition (just for a month) if you are able to use both options App Builder/Web-Based App Builder, to create the app in a way that you don't need to be suscribed more time to Professional Edition to be downloaded by the users in Google Play/Kindle Store, and it should work for Applestore (iphone apps) too. I mean, once again, no using Multi-issue and Renditions, cause in this case I know they are hosted by Adobe and you need the subscription to be downloaded.
I think there are discussions here about this topic, but it's not exactly clear what I'm asking. So, I still don't know if I should buy the Professional Edition or go to another supplier as you said.
I hope that Adobe improve these functions! There should be native support for these platforms, cause at the end you only can publish to the applestore with the Single Edition and everbody knows the "too booky problem" with the apps. And we should have support to publish to ibookstore because of that too, without third party solutions.

Making ActiveX Server with App Builder

OK I am writing a program in C++. I want the GUI to be in Labview and I need the C++ program and Labview GUI to communicate. So I used the app builder to create an ActiveX Server. So how do I use this? Do I use the GUI.tlb instead of the normal labview.tlb? Do I still create an application reference to Labview or do I create an application reference to GUI.exe since this is my executeable now? I can't find much documentation on this at all... Please help!

> OK I am writing a program in C++. I want the GUI to be in Labview and
> I need the C++ program and Labview GUI to communicate. So I used the
> app builder to create an ActiveX Server. So how do I use this? Do I
> use the GUI.tlb instead of the normal labview.tlb? Do I still create
> an application reference to Labview or do I create an application
> reference to GUI.exe since this is my executeable now? I can't find
> much documentation on this at all... Please help!
Switch over to using the GUI components that you mention. Think of it
this way, your C++ program could need to use both LabVIEW and GUI. For
that to work, most of the connection pieces have to be specific about
what they are dealing with.
Greg McKaskle

App Builder produces "Not Executable" error with Strictly Typed VI Refs

There is a very frustrating problem with the app builder in LV 8.0.1. Certain VIs compile and run fine in labview, but the app builder
refuses to make them into applications.
The error message is very long and ends with something like "The VI is not
executable". Standard advice for this problem is to force LV to recompile
everything you're building by either mass compiling or ctrl-shift clicking the
run arrow, but this hasn't worked for me in two separate cases (completely
different projects).
It seems that this problem is caused by wiring a strictly typed VI reference to
an invoke node with the FP.open method selected. In both cases I resolved
the issue by changing the Static VI Reference to be weakly typed (right-click
the static vi reference and make sure "Strictly Typed VI Reference"
is unchecked). After that, the project build successfully.
This is very hard for a user to track down for several reasons:
- The error message in the application builder does not give any
indication as to what the real problem is
- The app builder reports that the top-level VI is broken, even when the
strictly typed reference and invoke node may occur in a sub VI
- Nothing (that I can
find at least) in the documentation suggests that strictly typed references
won't work with the Open.FP method.
There is a page that says "some of the properties and methods do
not work when you configure this function to output a strictly typed VI
reference," but no indication is given of which methods fail
Note that in one case I was also able to make the project
build by deleting an instance of "IMAQ Create.vi" from the top-level
VI. I
have no explanation for this.
Hopefully this post will save some other users the trouble
of tracking this down and maybe even get NI to correct the issue for future
versions.
Adam Brewster

Hello Adam,
Thank you for sharing your experience and insight. Your post was well thought-out and offered a
good description of the problem as well as some possible workarounds. I believe that the issue has been filed and
is under investigation (3TU8T8V9). Feel
free to post back after the next LabVIEW release and inquire as to its status.
Thanks again,
Travis M
LabVIEW R&D
National Instruments

When creating an Android app in DPS App Builder, why do I not have the option of "Multi Folio with Amazon Subscription"?

The only option available is Google Play. Why is this happening?

I found a folder with an old APK file that worked. I wish I could edit it because it has the wrong splash screen attached to it, but at least the app is working. I wish I could have the app back in app builder and be able to edit that. I understand that you all aren't going to support these Amazon Subscription apps but we have current subscribers and they may have a full year left. We are stuck with an app that we still need to use until their subscriptions are up before we can make a change to how our android user are going to receive their magazines. Adobe should allow some sort of support for this type of situation. Now I have an app with a bad splash screen that looks completely unprofessional. Is there anyway to recover the file in App Builder? Is that what you were referring to or were you just referring to the APK file? I do appreciate all your help and attention to this.

My CC Desktop App (Mac) Home Panel is Hanging with a Spinning Gear Wheel

I'm running Adobe CC Suite on a MacBook Pro (OSX 10.7.5). Everything was working fine until I shut off and unplugged my laptop for a weekend. When I started it up, the CC Desktop App launched and complained that it couldn't find an Internet connection (even though my browser and Apple Mail apps were working fine.) I closed the CC Desktop App, reopened it, and ever since then, the CC Desktop App Home panel hangs with a spinning gear wheel. The Apps panel in the CC Desktop app seems fine.
I tried deleteing the opm.db file inside the OOBE folder in my User Library. This caused the CC Desktop App to ask to to login upon launch. But, once I logged in, the spinning gear wheel started up again.
Anyone know what might be going on here or how to fix this problem?

Abhijit,
I'm afraid that my problem with the CC Desktop App Home panel is NOT a disk permissions issue...
Per your suggestion, I verified my hard drive, repaired permissions, and rebooted my laptop. However, when I click on the Creative Cloud icon in the Finder's menu bar, the Home panel still displays a continually spinning gear wheel, as it did previously. The Apps panel is properly displayed, and the Files and Fonts panels display "coming attractions" messages; I don't have any projects in the Behance panel.
Prior to visiting this forum, I did a Google search on the problem of "CC Desktop App Home Panel Hangs," and I found a couple posts suggesting that the only way to cure this problem is to uninstall all CC/CS6 apps, use Adobe Cleaner to clean up the CS6/CC installation, and then reinstall all the apps via CC...and that doing all this does not necessarily prevent the problem for recurring.
I must say that I'm finding certain aspects of the Creative Cloud implementation to be surprisingly buggy. I've already lost a couple day's work to dealing with Creative Cloud installation and functionality issues--which is very frustrating, to say the least.
That being said, if you have any other suggestions, I'm willing to try them, as I would like to get my Creative Cloud installation working properly.

Linux app builder hangs with daqmxbase 1.5.0-f2

Similar Messages

Maybe you are looking for