Lost connection between audio and video

Hello. Is there anyone out there that can explain why it does this Gyazo - 4c7ff4b6ffe628c097e099abeecab242.png when I'm dragging video, which was recorded toghether in Photo Booth on Mac. I want to drag the video together with the audio. I have done this before but now it just changed? Thanks.

Select both the audio and video and right-click 'link'

Similar Messages

  • How to fix problems between audio and video sync?

    Hello, I have this old camera DSR 200P and I'm trying to import to my final cut pro x. The importation success well but at the end the syncro between audio and video doesn't work. How can I fix it?
    It's possible my mac doesn't accept this kind of camera or should I change any options of final cut?
    Thank you

    I use to edit footage for a client that was recorded on a DSR-250 (successor of the DSR-200) and every time, every single time, the audio sampling rate would not match my Sequence settings of 48khz, 16bit.  The sampling rate of the captured video was always off by a slight amount. It might be 47999.9 one time and 48000.1 the next time ... but it was never at 48000 as it should have been.  I chalked it up to Sony using cheap synthesized crystals (frequency generator) to control the rate.
    Anyway, the fix was to export the captured clip using QuickTime Pro with the export's audio settings to 48khz, 16 bit.
    -DH

  • Create a DVD using Premiere Pro and Encore - delay between audio and video (in ms)?

    I created a DVD and need to be sure that audio and video are in perfect sync (smaller than 1 millisecond).
    Is this even possible with Premiere Pro / with DVDs in general?
    My sequence settings in Premiere are:
    DV PAL, 25 fps, 720x576 (16:9), D1/DV PAL Widescreen, lower field first, Audio: 48000 Hz
    My DVD settings in Encore are:
    MPEG-2 (MainConcept MPEG-Video), 720x576, 25 fps, lower field first, Widescreen 16:9 (1,458), Bitrate VBR, 2-Pass, Min 1,5 MBit/s Target 4 MBit/s, Max 9 MBit/s, GOP: M-Frames 3, N-Frames 12, Audio: Dolby Digital, 192 kbit/s

    I created a DVD and need to be sure that audio and video are in perfect sync (smaller than 1 millisecond).
    Is this even possible with Premiere Pro / with DVDs in general?
    Frame accurate is the best you can achieve and that means 33 milliseconds at best.

  • How do I fix lost connection between Photoshop and Dreamweaver CS4?

    How do I fix the lost connection in Photoshop CS4 to Dreamweaver? When I save for web and devices, Photoshop doesn't save for web but instead saves to the original file in Photoshop. The image doesn't show up in Dreamweaver's image gallery at all. Do I remove both from my hard drive and reload both? I don't want to loose anything in Dreamweaver or Photoshop.

    Not sure exactly what you are asking since I am still a student learning Dreamweaver so I can only describe what is happening in non-technical terms. I have set up files in Photoshop CS4 for images that I plan to use in Dreamweaver as a gallery of thumbs that enlarge using the Behavior panel. I did this with over 100 images, first creating the correct size in Photoshop, then going to Save for Web and Devices, saving, and the image would then show up in my images list in Dreamweaver.
    Now, when I save for Web and Devices, save, it doesn't show up in Dreamweaver. Instead, it saves it back into my original Photoshop file with hyphens between each word.
    I have Windows XP Professional, Adobe Creative Suite CS4.
    I don't know how this glitch happened, I did nothing different and have used the process successfully already over and over. I read as much as I could understand on the Adobe website and apparently glitches do happen but I don't understand how to resolve this. Do I uninstall both Photoshop and Dreamweaver, and reinstall both?
    I very much appreciate assistance!
    Sieglinde Anderson

  • Scripting: How To Tell Between Audio and Video Track?

    When I create a collection of tracks from the main library and iterate through them, I get everything (in my case, video and audio tracks - no podcasts or TV shows as of yet). In checking the "Kind" class, they all have a value of "1".
    How can I tell if a track I'm looking at is audio or video? Also, when I do start downloading podcasts and/or TV shows, is there a way to differentiate them also?
    Thanks

    chillpill 
       **** so much for that on the Western Digitals.  The interface is USB3
    goodness, yes, youve got one of those OLD WD drives that has the controller board AND USB all as ONE SINGLE UNIT
    write that HD off. 
    your "classique"  HD here:
    http://karlsbakk.net/bilder/WD10TMVW/wd10tmvw-2.jpg
    tjk Wisconsin 
    So being USB3 doesn't tell us anything at all.
    Yeah it does, it tells me its one of those OLD HD that was made with the "lets save 2 cents and make it all one piece" philosophical designs.

  • Disconnect between audio and video with movies

    I'm just getting started with the 80 GB iPod and a movie I loaded will play, but there is about a second or two delay between the video and the audio with the movie. Any suggestions?

    Can you mark the thread as Answered then please.
    10:13 PM Friday; January 25, 2008

  • Timing Between Audio and Video Thrown Off

    I have a large project to complete. The other day, I logged an MPEG that's approximately 50 minutes using pen and paper. When I loaded this MPEG into Adobe Premiere CS4 and started separating clips based on my notes, I noticed that the video no longer matched the time codes I'd written down; Video that was supposed to have already taken place hadn't started yet.
    At first, I thought the time code for the video was different than what Windows Media Player displayed, but there's another issue: The audio isn't in sync with the video. It's been displaced so that it begins about 16 frames before it should.
    I checked the framerates of both my project and the video. They're both at 29.97 fps. I'm out of ideas. Any help would be appreciated.
    OS: Windows 7 64-bit
    Processor: Intel(R) Core(TM)2 Duo CPU     E6550 @ 2.33GHz 2.33 GHz
    Memory: 4GB RAM (3.87GB usable)
    Card: ATI Radeon HD 2400 XT

    What are the details of what is inside your file?
    Read Bill Hunt on a file type as WRAPPER http://forums.adobe.com/thread/440037
    What is a CODEC... a Primer http://forums.adobe.com/thread/546811
    What CODEC is INSIDE that file? http://forums.adobe.com/thread/440037
    Report back with the codec details of your file, use the programs below
    For PC http://www.headbands.com/gspot/ or http://mediainfo.sourceforge.net/en
    For Mac http://mediainfo.massanti.com/
    http://blogs.adobe.com/premiereprotraining/2011/02/red-yellow-and-green-render-bars.html
    Once you know exactly what it is you are editing, report back with that information... and your project setting, and if there is a red line above the video in the timeline, which indicates a mismatch between video and project
    Read Bill Hunt on editing a VOB/MPG file http://forums.adobe.com/thread/464549
    Edit Vob http://premierepro.wikia.com/wiki/FAQ:How_do_I_import_VOB_files_/_edit_a_DVD%3F

  • Lost connection between ACS and AD

    Hi
    I'm having a trouble with authentication to my WLAN. We are running a solution with LEAP and ACS 3.0 which gets it's users from our Active Directory. During the summer our ACS-servers seems to have lost the AD-connection and I'm no longer able to EAP-authenticate. All I get in the ACS is "Radius extension DLL rejected user".
    The AD and the ACS are on the same network but not on the same machine. I can log in if I add a local user in the ACS. I've also tried to empty my cached user database in the ACS but to no avail.
    One theory of mine is that it has something to do with a couple och hotfixes that Microsoft released in the middle of July.
    T.I.A
    /Tommy

    Hi
    Thanks for your replies. An update on the issue:
    I've gone through the issues in the suggestion made by cisco in the link:
    http://www.cisco.com/en/US/products/sw/secursw/ps2086/products_field_notice09186a00800b1583.shtml
    but to no avail.
    At first we could se an error in the eventlog stating that the user didn't have sufficient rights but it disapeared when we created an account and ran the ACS-services via it.
    After that we tried to set up a local user in the ACS and it works like a charm even then the AD-accounts can't connect.
    We also tried to remove the hotfixes released by Microsoft but still nothing.
    Right now it seems as if the AD authenticates the user correctly but then the ACS says no. Here's the eventlog and the corresponding ACS-log.
    NT
    AUTH 08/19/2004 08:20:27 I 0266 1524 External DB [NTAuthenDLL.dll]: Starting MSCHAP authentication for user [LINEDU\gustomedu]
    AUTH 08/19/2004 08:20:27 I 0266 1524 External DB [NTAuthenDLL.dll]: Attempting NT/2000 authentication
    AUTH 08/19/2004 08:20:27 I 0266 1524 External DB [NTAuthenDLL.dll]: NT/2000 authentication SUCCESSFUL (by METIS)
    AUTH 08/19/2004 08:20:27 E 0266 1524 External DB [NTAuthenDLL.dll]: LookupAccountSidA failed
    ACS
    08/19/2004 08:20:27 Authen failed LINEDU\gustomedu Default Group 000a8aa291a8 Radius extension DLL rejected user .. .. 37 148.136.120.30
    The status right now is that it is working as long as we restart the ACS-server once a day.
    Tommy

  • Lost connection between ipod and laptop

    Hi there,
    Not sure if this is a question for ipod or itunes, but here goes.
    I recently purchased a 5th gen ipod and installed itunes on my 2 PC's and a PC based laptop. All worked fine.
    Now when I connect the USB cable to the laptop, I hear three quick beeps, (not the usual 2 beeps) my ipod starts charging, but I can't see the ipod in itunes.
    When I check device manager, there is an entry with a yellow question mark (labelled ipod) which says the driver is not installed. However when I load the itunes CD, the wizard says no drivers found.
    My ipod works fine on the 2 other PC's.
    I tried system restore but for some reason it fails to go back to any restore points. whether that's part of the problem or a red herring, I haven't a clue.
    Can anyone help?
    Many thanks
    Packard Bell   Windows XP   Easynote laptop

    Could you be more specific like what happened will it not let you log in or not even go to that application be more specific and I will try to help you out

  • Lost connection between CTC and ONS 15305!

    I have one ring using ONS 15305 V3.0 nodes. All nodes are supervised by CTC. After a broken cable case, one node could not be supervised. However, I can access that node via CEC 2.2.In network view mode of CTC, I can see that node is logged in but logged out immediately then logged in and logged out again. I can not log in that equipment on-site via Management Port.

    Could you be more specific like what happened will it not let you log in or not even go to that application be more specific and I will try to help you out

  • I lost connection between Ipod and Macbook Pro Notes when I changed OS from Lion to Mountain Lion.

    I changed OS X from Lion to Mountain Lion and:
    New Mail application has no Notes.
    A new Notes application is available.
    In my Ipod I am was using Note application that normally was sincronized with Mail Note application. How can do a similar job?
    Devices involved:
    MacBook Pro 13-inch, Mid 2010.
    Ipod Touch, software version 4.2.1

    try this:
    open disk utility and verify your disk permissions - if errors are found repair them....
    then go to system preferences - network - advanced - look for the dns tab and enter the dns you see on the image below.  after you've done that, restart your macbook and see if your internet pages loads faster.
    good luck.

  • Premiere Pro CC: audio and video is out of sync after export

    Hi folks! I downloaded trial version of Adobe Premiere Pro CC. Captured gameplay with bandicam in Motion Jpeg Format (as advised) 30 fps and made a 40 minutes lenght clip. But there is an issue: in my project audio is synchronized with video, but when i export - it's lost (and i think to further we watch video, the bigger is the synch gape between audio and video, in increases gradually). I tried various formats, tried to use option "delete rendered files" prior to export, tried "match source" option, tried to choose various drives for exporting - nothing helps.
    Help, how to solve this problem?

    Handbrake is a free-download program that takes variable-frame-rate footage and converts it to constant frame-rate. VFR to CFR, if you will.
    Going back to your reply to my first post, you noted there had been some kind of "hardlimit" to 30fps that you hadn't chosen. I'm guessing that would have made this track CFR, and what you've got instead is VFR. So you might try recording another bit after selecting that setting to hardlimit the frame-rate, and see if it works better through PrPro to export.
    Next ... so, you've got a 30fps probably VFR video track, and it appears a WAV file is your audio ... was that produced by the Bandicam program while it was recording your program? Or is it from another source and you pasted it into your sequence?
    Neil

  • Audio and video clip lengths differ in encore timeline

    Hi
    I have been working to build a BD-R H.263 ac3 disk.  I used AME from within Premiere Pro to export the M4V and (at the same time) AC3, using the present defualt parameters-no tweaking of any setting.  The clips appear to play great on encore's monitor--everything in sync.And on the burned BD-R
    However, I am getting the black screen between clips in the timeline when played in the standalone BD player, or (when I had one clip to a timeline) in a playlist.  a previous poster made note of different length audio and video clips.  I zoomed on the timeline and lo and behold--the  the audio and video clips are different lengths.
    This is with the timeline fully expand--each division is a frame. Note that break between the two audio clips is offset from the break between the two video clips by two frames.  This offset is after several clips.  I could find no information on what the one frame crosshatching at the end of the leading clips means.  Can anyone explain this cross hatching?  What do I do about it?  the image below is after the first clip in the timeline:
    In this image, the offset is less than a full frame??????
    I tried using the trim tools to bring these together-but, the trim tool only lets it jump a full frame and then only to a GOP boundary, which doesn't help because the boundaries are obviously different fro the video and audio track.
    I want to emphasize that these assets were created from the Premiere CS4 timeline (which had no offset between audio and video) using the default H.263 and AC3 presets in AME and the same presets selected in Encore.
    The offsets do not appear to cause the actual audio and video to go out of sync when I play the burned disk. But, I get the 1-2 second wait between menus and chapters, or with items in a playlist.
    The audio offset suggests that the player may not know what to do when faced with a chapter point that is different on the audio and video tracks, although, I will note that encore snapped to the joints in the video track not the audio track.
    You can see from this listing that several of the clips audio and video lengths that differ by one frame.  By the end of the timeline, the cummulative offset is 3 seconds (48 minute timeline)
    Can anyone shed any light on this?  Thanks

    I don't think that I had the same problem that you do, but I thought I'd throw in my two cents just in case it might help. Encore would not build the output; it said something like the inpoint and the length did not match the endpoint. Actually, I think this happened in several different situations. In one case I simply adjusted the audio and video tracks to match endpoints. In the other case I went back to Premier and found that in some cases where I had added transitions it had shifted the endpoints of the audio and video tracks so they did not match. I removed the transitions. It didn't matter that much to me since I'm doing this for personal use. Is it possible those crosshatched lines you're seeing are transitions?
    I am using CS 3 and editing HD. I have had many problems with encore. I read in the form someplace that it had a hard time handling H.264 so I changed to MPEG-2 and that fixed one problem. In another case it couldn't find some files and I found some advice not to use HD or wide menus, so I switched to standard 4:3 menus and it worked.

  • Audio and video offset in imported media

    When I import a media from the camera who took the film, there is an offset of 2 seconds between audio and video track.
    I have to dissociate the two tracks and create manually an offset in order that the sound match the images.
    How to prevent that and get the 2 tracks audio and video in correct synchro, just like when viewing the film directly from the camera ?
    Thanks,
    Pierre

    pdemeure
    We are very glad that you have found the answer to your Premiere Elements question which appears to relate your Samsung Galazy camera/Premiere Elements 11 Mac/"out of sync" audio/.
    But, if you have the time, could you explain why you "...created the project using a PAL setting at 25 frames...." (you did not say what PAL setting beyond the frame rate)> I ask you this question since you stated earlier in this thread that your source media and project setting were:
    I use Premiere Elements 11 on Mac OSX 10.8
    The video is done with a Samsung Galaxy Camera.
    The format is MP4 1920x1080 30frames    H.264, AAC
    The settings of the project are in accordance with the file : image 1920x1080, 29,97 frames
    The answer to the above would help to explain how you came to your success when you wrote
    I've found the reason of the offset : I had created the project using a PAL setting at 25 frames. I've now created a new project using  the NTSC HD Full HD 1080i 30 and that works fine.
    Thanks.
    ATR

  • No audio and video with iChatAV connecting to one computer

    Hi all, very strange issue here. Have two new alu iMacs, one 2.4 24" and one 2.0 20". Set them up at home and everything worked fine. Set up two seperate AIM accounts and got audio and video iChat working with no problems at all. Got it to work between my two computers and with another one. I then moved my 20" iMac to my office. I am now only able to send text messages, no audio and video with iChat any more. Get message that account doesn't answer. Of course we accept and everything. The strange thing is that both my computers do get audio and video working connecting to my friend's iMac with iChatAV only not when connecting to eachother. When we tried to make a converence call, my friend had to invite us and then my home computer could see and hear me at the office and my friend, while my friend and I could see and hear eachother, but only could hear my home computer. What could be wrong here?

    Can you mark the thread as Answered then please.
    10:13 PM Friday; January 25, 2008

Maybe you are looking for