MacBook Pro won't sleep in OS X after reboot from Windows (again!)

This problem originally occurred about a year ago and no solution was found then but after a time, it simply went away. Well, now it's back: after a reboot into OS X (10.6.7) from Windows (7 Ultimate 64 Bit), my MacBook Pro refuses to sleep until rebooted a second time, after which it behaves correctly again. The Console log reports the following message: "System Sleep prevented by active remote login session (600 second threshold)". I've disabled Growl and DropBox (possible suspects last time) to no effect, reset the SMC and PRAM, all the usual things. I've tried when connected to mains power or battery, on wired, wireless or no network at all and still the same problem. Sleep behaviour under Windows is correct. Hopefully the problem will eventually cure itself as it did last time but I would like to discover the reason and find out what this "remote login session" could possibly be. To reiterate, this ONLY occurs immediately after rebooting from Windows.

Tried repairing BootCamp in 7, no change, don't think there was anything wrong with it in the first place.
Here is a section of the log after reboot from BootCamp and it says "System Sleep prevented by active remote login session (600 second threshold)". This ONLY happens after a reboot from Bootcamp, after another reboot all goes back to normal. What could the "active remote login session" be?
From log:
21/04/2010 23:08:56 kernel PM notification cancel (pid 16, configd)
21/04/2010 23:08:56 kernel IOPMrootDomain: idle cancel
21/04/2010 23:12:00 configd[16] PowerManagement configd: System Sleep prevented by active remote login session (600 second threshold).
21/04/2010 23:12:00 configd[16] PowerManagement configd: tty sleep preventer: /dev/console
21/04/2010 23:12:00 configd[16] PowerManagement configd: System Sleep prevented by active remote login session (600 second threshold).

Similar Messages

MacBook Pro won't sleep in OS X after reboot from Windows

I have Windows 7 Ultimate 64 bit running on a BootCamp partition on my MacBook Pro running OS X 10.6.3. When I first installed 7 last year, I initially had a strange problem in that the Mac wouldn't sleep (default settings) when rebooted back into OS X from BootCamp. If I did another restart in OS X, everything returned to normal. I never found a solution to the problem but after a while it went away and things worked properly. Now, after several months and for no good reason I can think of, the problem has returned. Everything works correctly in both OSs except for this. Any help would be appreciated.
Clive

Tried repairing BootCamp in 7, no change, don't think there was anything wrong with it in the first place.
Here is a section of the log after reboot from BootCamp and it says "System Sleep prevented by active remote login session (600 second threshold)". This ONLY happens after a reboot from Bootcamp, after another reboot all goes back to normal. What could the "active remote login session" be?
From log:
21/04/2010 23:08:56 kernel PM notification cancel (pid 16, configd)
21/04/2010 23:08:56 kernel IOPMrootDomain: idle cancel
21/04/2010 23:12:00 configd[16] PowerManagement configd: System Sleep prevented by active remote login session (600 second threshold).
21/04/2010 23:12:00 configd[16] PowerManagement configd: tty sleep preventer: /dev/console
21/04/2010 23:12:00 configd[16] PowerManagement configd: System Sleep prevented by active remote login session (600 second threshold).

MacBook Pro won't mount *2nd* DVD until after reboot.

MacBookPro5,1, Intel Core 2 Duo, 2.53 GHz, 4G ram, Mac OS 10.6.8
This MacBook Pro will not mount more than 1 DVD without a reboot in between discs!
These are commercial movie DVD's in excellent condition.
I can mount and watch one commercial DVD with no problems, but when I eject that disc after viewing and insert another commercial disc, it will not mount. I can hear the drive spin up, then spin down, then spin up again, etc... eventually the Finder takes over and says that I've inserted a blank disc and do I want to ininialize?
Eject command does not work while this spin up/spin down loop is occurring. If I Shut Down before the Finder finally recognizes there's a disc in trouble, then reboot and hold the trackpad button, the disc will eject. If I then trash all DVD preferences, the disc will mount and eject on command.
Inserting another disc will result in failure to mount! Etc...
Any ideas?

I should have updated this ages ago. Sorry.
The solution to the problem was to remove the DVD drive, take the cover off it and clean the lens in the reader mechanism. Just Google up the disassembly directions for your particular Mac model.
Downhillracer1's solution, compressed air blown in through the disc slot is certainly easier and might do the trick if all you've got is a spec of dust on the lens, but if it's a problem with some kind of film deposited, opening it up and cleaning the lens is more thorough.
My DVD drive now reads and burns with no problem.

MacBook Pro won't sleep when charging

My 15" i5 MacBook Pro won't sleep when charging; a reboot of the machine solves the problem temporarily, but it always recurs. When I close the lid and listen carefully, I can hear hard drive activity; the drive sounds like it keeps spinning up every 10 seconds or so.
This is not an issue when trying to sleep when running on the battery only. Any advice?

I don't have launch2net installed.
I'm not sure how this will help, but here's the last 5 lines from Console:
11-07-13 5:19:46 PM          Butler[156]          cache: adding applications...
11-07-13 5:19:46 PM          Butler[156]          cache: adding addresses...
11-07-13 5:19:47 PM          Butler[156]          cache: categorizing...
11-07-13 5:19:49 PM          Butler[156]          updated abbreviations cache (enabled)
11-07-13 5:19:58 PM          SIMBL Agent[133]          warning: failed to get scripting definition from /Applications/Utilities/Console.app; it may not be scriptable.

MacBook Pro won't sleep or shutdown (intermittent problem)

Every so often my MacBook Pro won't sleep or shut down. I can't find any rhyme or reason to it.
I notice the problem when I close lid, and it doesn't go to sleep. I then hit apple menu:sleep, and it does nothing. I hit shutdown, and OS shuts down, but gets stuck at blue screen with spinning circle indefinitely. Have to hold power button for 5 seconds to finally shut down. Startup is then slow, but doesn't give me an error message indicating improper shutdown or failure.
Most of the time it sleeps fine and shuts down fine.
Other posts seemed to have the problem more reliably, and the fix had to do with startup items. Mine is intermittent, and the only items in my startup folder are Norton Antivirus and Parallels.

I am also experiencing the exact same problem you are describing. Completely random when the machine will not sleep or shutdown, although it seems to occur more often when I've had the machine running for a few days, moving between home and office locations.
I have VMWare Fusion and Office 2004 installed. No iStatPro. I'm wondering could it be related to the kernel extensions that VMWare and Parallels install? Is anybody experiencing the non-shutting-down problem who doesn't have either VMWare or Parallels installed?
I found the following section in my system.log file that occurred the last time the machine wouldn't shut down. May be of some use to somebody
Aug 31 18:07:10 monza loginwindow[90]: sendQuitEventToApp (Microsoft AU Daemon): AESendMessage returned error -1712
Aug 31 18:07:21 monza shutdown: halt by james:
Aug 31 18:07:22 monza SystemStarter[14860]: authentication service (14870) did not complete successfully
Aug 31 18:07:28 monza SystemStarter[14860]: The following StartupItems failed to properly start:
Aug 31 18:07:28 monza SystemStarter[14860]: /System/Library/StartupItems/AuthServer
Aug 31 18:07:28 monza SystemStarter[14860]: - execution of Startup script failed

After 10.7.4 update macbook pro won't sleep

after 10.7.4 update, macbook pro won't sleep.

Test after each of the following steps that you haven’t already tried:
Step 1
 ▹ System Preferences ▹ Energy Saver ▹ Power Adapter ▹ Wake for network access: uncheck. You may need to unlock the preference pane by clicking the lock icon in the lower left corner and entering your administrator password.
Step 2
 ▹ System Preferences ▹ Energy Saver ▹ Schedule… ▹ Start up or wake: uncheck
Step 3
 ▹ System Preferences ▹ Print & Scan ▹ Open Print Queue...
Check all printers for unfinished jobs. Deal with any you find.
Step 4
Disconnect all wired peripherals except keyboard, mouse or trackball, and monitor, if applicable.
Step 5
Launch the Activity Monitor application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Activity Monitor in the page that opens.
Select All Processes from the menu in the toolbar, if not already selected. Enter “powerd” (without the quotes) in the "Filter" text field. Select the powerd process and click the Quit Process button in the toobar (stop-sign icon.) In the sheet that opens, click Force Quit. You’ll be prompted for your administrator password. The process will be relaunched immediately.
Step 6
Boot in safe mode and log in. The instructions provided by Apple are as follows:
Be sure your Mac is shut down.
Press the power button.
Immediately after you hear the startup tone, hold the Shift key. The Shift key should be held as soon as possible after the startup tone, but not before the tone.
Release the Shift key when you see the gray Apple icon and the progress indicator (looks like a spinning gear).
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Note: If FileVault is enabled under Mac OS X 10.7 or later, you can’t boot in safe mode.
Safe mode is much slower to boot and run than normal. Don’t launch any applications at first. If sleep still doesn’t work properly, back up all data and reinstall the Mac OS. After that, if you still have the issue, make a “Genius” appointment at an Apple Store to have the machine tested.
If sleep now works as expected, go on to the next step.
Step 7
Still in safe mode, launch the usual set of applications that are running when you have the problem, including your login items, one at a time, testing after each one. Some applications may not work; skip them. You might be able to identify the cause of the problem this way.
Step 8
If sleep is still working after you’ve launched all the usual applications, reboot as usual (not in safe mode) and test again. If sleep still works, you’re done, at least for the moment.
If you still have the sleep issue after booting out of safe mode, post again.

My macbook pro won't sleep - if I select sleep it does so initially, then the disc-drive appears to kick in and it comes back to life. It also won't turn off (again, the disc drive kicks in) unless you hold the power-button down for a long period.

My macbook pro won't sleep - if I select sleep it does so initially, then the disc-drive appears to kick in and it comes back to life. It also won't turn off (again, the disc-drive kicks in) unless you hold the power-button down for a long period. Help?

Hi a,
Try an SMC Reset: http://support.apple.com/kb/HT3964

ITunes on MacBook Pro won't recognise my iPhone 4S after downloading latest iTunes. What to do?

iTunes on MacBook Pro won't recognise my iPhone 4S after downloading latest iTunes. What to do?

iOS: Device not recognized in iTunes for OS X

Macbook pro won't power up or charge after i cleaned the screen and keyboard with a damp cloth.

My macbook pro won't power up or charge after i cleaned the screen and keyboard with a damp cloth

Do not try to use it. Make an appointment at an Apple store genius bar and have the technicians evaluate it for FREE.
Ciao.

MacBook Pro won't sleep with external monitor

Hello,
have a problem. I'm using external monitor with my MacBook Pro. If I close the lid, I see all windows on external monitor and Yosemite won't sleep. Can you help me please? My external monitor is Samsung 21.5" and I'm connecting it to MacBook Pro via DVI.
Thank you

Hey Renecek,
My first thought was, "Hey, you are using closed-clamshell mode".
How to use your Mac notebook computer in closed-clamshell (display closed) mode with an external display - Apple Support
But then I realized, wait, you want it to sleep.
For that, check out the suggestions in these articles.
OS X Yosemite: If your Mac won’t go to or stay in sleep
OS X: When your Mac doesn't sleep or wake - Apple Support
Take care,
Nubz

MacBook Pro won't sleep, even in safe boot

Hey gang,
I can't figure out what to do with this problem. I recently did an archive & install of 10.5 on my 2.33 GHz MacBook Pro Core 2 Duo, and then used software update to get to 10.5.2.
Ever since doing that, my MacBook Pro will not sleep on its own anymore. It will sleep the display, but it won't sleep the system. (I can close the lid and it will sleep. I can also choose "Sleep" from the Apple Menu, and it will sleep. It just won't sleep on its own.)
At first I thought it might be Time Machine that was preventing it from sleeping, but I turned off Time Machine and the problem persisted. I tried creating a new user, and the problem persisted. In fact, I EVEN BOOTED IN SAFE MODE AND THE PROBLEM PERSISTED!
I went through every single step outlined on this page (yes, every single step), and the problem still persisted: http://www.macfixit.com/article.php?story=20070129234938244
Does anybody have any ideas what I can do at this point? I'm pulling out my hair over here....
Thanks!
Scott

I see you've done your homework. I have this no auto-sleep problem on my Mac pro and none of those things worked for me either but I thought you should give them a shot.
I made a little sleep program of my own. You are welcome to try it. It's a very simple shell script that checks system idle time and if it's bigger than the sleep timer you set in system preferences it puts your computer to sleep. It will work so long as you can manually put your computer to sleep from the apple menu.
You'll also need to create a launch daemon to periodically run the script.
here are the steps to do it.
1. copy and paste the following into TextEdit.
#!/bin/bash
idl=$"`ioreg -c IOHIDSystem | awk '/HIDIdleTime/ {print int($NF/1000000000); exit}'`"
sleeptimer=$"`defaults read /Library/Preferences/SystemConfiguration/com.apple.PowerManagement "Custom Profile" | grep "System Sleep Timer" | awk '{print $5}' | sed -e 's/;//g'`"
st=`expr $sleeptimer \* 60 `
if \[ $idl -gt $st \]; then
shutdown -s now
fi
2. Format it as *plain text* (shiftcommandT in TextEdit) and save it as sleep.sh (don't use the .txt extension) at the top level of your hard drive.
3. make it unix executable by entering the following command in terminal.
*chmod 755 /sleep.sh*
4. Download and install [Lingon|http://lingon.sourceforge.net>.
5. Open Lingon and create a new *Users Daemon*
Call it,say, com.sleep.launchd (the name is not important)
On line 2. enter /sleep.sh
and in section 3 set it to run every 30 seconds.
Click save (you'll have to enter your admin password).
6. Restart.
That's it. Once this is done you can forget about it. The sleep settings are still controlled from system preferences. The sleep agent will work with every user and even over the login window.
To uninstall it, open Lingon, select the launch daemon you made and uncheck the box "Enabled" in the upper right corner. save and restart.

Macbook Pro won't sleep when lid open

My 2011 Macbook Pro won't go to sleep if I leave the lid open. I have checked System Preferences>Energy Saver and the display/computer sleep is set to 10 min for both Battery and Power Adapter settings. Even if I close all the applications down, my computer will still not go to sleep. The battery just gets completely drained if I forget to close the lid. Help?

1/31/13 9:44:10 PM PST
Assertion status system-wide:
   PreventUserIdleDisplaySleep             0
   CPUBoundAssertion                       0
   DisableInflow                           0
   ChargeInhibit                           0
   PreventSystemSleep                      0
   PreventUserIdleSystemSleep              0
   ExternalMedia                           0
   DisableLowPowerBatteryWarnings          0
   EnableIdleSleep                         1
   NoRealPowerSources_debug                0
   UserIsActive                            0
   ApplePushServiceTask                    0
Kernel Assertions: None

MacBook Pro won't Sleep or Shut Down

My MacBook Pro won't go to sleep or shut down.
Sleep
The behaviour is the same whether I press the power button and choose 'Sleep' or whether I choose 'Sleep' from the Apple menu. The computer stays awake, but it loses the ability to respond to Keyboard Shortcuts, such as those used for Expose, and can get stuck in some Apps. If I close the lid the computer stays awake but the screen blacks out. Re-openning the lid does not re-illuminate the screen so I have to force shut down and re-boot.
*Shut Down*
The behaviour is erratic. Sometimes the computer simply ignores me (although it does close the 'Are you sure you want to Shut Down now?' window), and sometimes it goes to the blue screen with the progress circle and hangs.
*What I've tried already*
- Resetting the SMC
- Checked the Firmware versions are the latest

Sorry for the repost. New to this forum and I hadn't seen the answers to the last time I brought up this topic here:
http://discussions.apple.com/message.jspa?messageID=5050821

Macbook Pro won't sleep after updating to 10.4.11

Hi,
I just updated to 10.4.11 reluctantly from 10.4.9 as whenever I do update I always have issues...I basically just went to software update last week and updated to everything I could. I've just been reading the forums and noted that updating is not always that easy...
Well basically my computer won't sleep if the lid is left open, this is IMMENSELY annoying since I often leave my desk to work on drawings, and I don't want energy being wasted like it is at the minute. Call me picky but I just want my computer to work.
I've reseted the PRAM, (option, alt, p and r), closed all applications, etc, but no luck...
Its a 2.2ghz MacBook pro, 2GB. Thank you in advance
Neal

The important thing for the future imho, is to always Repair Permissions before & after any update... seems to ward off most of these problems. Of course that is only good if the disk is Verified once in awhile.
Using Disk Utility in Mac OS X 10.4.3 or later to verify or repair disks...
http://docs.info.apple.com/article.html?artnum=302672
About Disk Utility's Repair Disk Permissions feature...
http://docs.info.apple.com/article.html?artnum=25751
In fact I'd start with those 2 now, if that doesn't help you may need to reapply some updates by getting them directly from apple>downloads.

Macbook Pro won't sleep

I have this setup: a MacBook Pro running Mountain Lion, an external 27" cinema display, a bluetooth apple keyboard and a bluetooth magic mouse.
The MacBook Pro runs with the lid closed.
It looks like the computer won't sleep anymore. It stays on for days when not using it. In my settings I have set I want the computer to sleep after 15 minutes of inactivity.
I prefer to switch off the keyboard and mouse when I'm away from my computer, so I can't use the Apple menu or shortcuts to make the computer sleep.
Any idea?

i am pretty sure this is because you have it connected to an external display. i am not sure if there is a workaround for this.

MacBook Pro won't sleep in OS X after reboot from Windows (again!)

Similar Messages

Maybe you are looking for