Management vlan with the 1000V and UCS

If I want to use VLAN 10 for management, I would have to configure the following:
1000V -VM vEthernet port profile access port with VLAN 10, Ethernet uplink profile includes VLAN 10
UCS - vNIC in Service Profile, include VLAN 10, and include VLAN 10 in uplink trunk from UCS
Upstream switch: Include VLAN 10 in trunk port.
OK?
Now, this management VLAN, can I Iuse this for everything? I mean for 1000V management VLAN, vSPhere management, FI management and switch management? Or should for instance the 1000V management be different from the others?

Hi Atle,
Yes, what you have mentioned is the correct in terms of activities you need to carry out. However i would like to add a few:
1) define the vlan on the UCS - unless you do this you will not be able to add it to the vnic. Plus once you have the vlan defined it will automatiaclly get added to the trunk list on the uplinks ports (unless you l2-disjoint configured)
You can have the same vlan for all the management, unless you have certain traffic you would not like certain device to see / reach.
./Abhinav

Similar Messages

Adobe Extension Manager loops with the following message: "The Extension Manager will now launch and

Hi, whenever I open Dreamweaver CS5 I get this message:
Adobe Extension Manager loops with the following message:
“The Extension Manager will now launch and finish updating Dreamweaver”.
Then the manager starts and I have to wait and click a few buttons until I can close it.
How can I stop the Extension Manager popping up?
Thanks for advice.

Seems to be a lot of this going on. Wondering if we're wasting our time with this??!!

How do I open photoshop? I have it downloaded and only the Adobe Application manager shows with the

How do I open photoshop? I have it downloaded and only the Adobe Application manager shows with the list of other software. I clicked on photoshop, but not responding.

Nobody can know. Your information is far too vague - no system info, no other details. Just saying that it doesn't work is not conducive to providing assistance...
Mylenium

Problem with the new server UCS C220 for set IP to CIMC

Hi
We’ve a problem with the new server UCS C220.
We bought two servers UCS C220 M3 for CallManager 8.6 with High Availability.
When we turn on the server during the boot and when it tells us, oppress F8 to enter at the CIMC and set the IP. But it never enters at the CIMC.
Then, we configure our DHCP server and our switch, we connect the three gigabyte ports to our switch to give him an IP to the CIMC, so and then can enter via browser, but neither works.
Note. The dedicated management NIC does not link, the other two ports do make link.
What do you suggest to put an IP to CIMC and start installing our applications?
regards

You may have noticed that there is no DVD rom on the c220. What you need to do is:
Login into the CIMC from your browser
Luanch the KVM
Insert the VMware DVD in your machines drive
On the KVM pop up there should be a tab to mount the drive, after mounting it click on Macros and choose ctrl_alt+delete to restart.
After the VMware OS installs press F2 to enter IP.
Browse to the VMware ip to download the Vsphere client
Open the Vsphere client, enter the ip of the vmware and the username will be root and no password if you did not set one.
You can now upload OVA templates or manually create virtua machine from this enviroment.
Hope this help

How do you manually manage podcasts with the new iTunes?

Like the subject line says: How do you manually manage podcasts with the new iTunes?
With the previous version of iTunes, when I plugged in my iPod, I could select the iPod, select podcasts, and manually delete episodes. With the new iTunes, I can't select individual episodes when looking at my iPod through iTunes. Is my only option to Sync? If so, why is that my only option?
This question probably has a simple answer, and I'm just not seeing it.

Rock,
I think I figured out a way to do what you want to do - which is the same way that I use Itunes with my Ipod. (My Itunes libary was destroyed last year so I can no longer auto synch my Ipod as I would lose thousands of songs).
Funnily enough, I discovered this new way of manually moving podcasts while trying to figure out what cpragman was trying to say (I never could - he must be smarter than me, as I couldn't get his method to work).
1. Open up your Itunes in your regular Library view. Choose Pocasts from the left hand side (either in the sidebar if you have that enabled, or from the little "radio" icon if you don't.)
2. Mouse to the podcast you want to place on your Ipod.
3. Right-click it. A long menu will pop up.
4. Move to the "Add to Playlist" option. As you hover, all your playlists will be visible. But at the very top will be the name of your Ipod itself (whatever you named it originally). Choose THAT name, and voila! That podcast will now copy to your Ipod and be easily available when you disconnect.
A nice feature of this method is that you can shift-click several podcasts at once and do the same thing, and all your selected podcasts will copy over (if you're like me and update your Ipod only every few weeks).
Hope this helps - let me know if it works for you!

Impossible to start UCM managed server with the WLS console

Hi,
I cannot start the UCM managed server with the WLS console. The node manager is running by startNodeManager.cmd. The admin server by startWebLogic.cmd.
When I start the UCM server with the console WLS (Environment, Servers, Control tab and Start on the checked server), it seems to be running (the state is RUNNING) but when I open the url on the the web server UCM there is a 404 error
In the log, there are many java.lang.ClassNotFoundException: oracle.jrf.wls.JRFStartup, oracle.security.jps.wls.JpsWlsStartupClass, oracle.core.ojdl.weblogic.ODLConfiguration, oracle.jrf.AppContextStartup, oracle.as.jmx.framework.wls.spi.StartupListener, oracle.ias.cache.Startup, oracle.dms.wls.DMSStartup ...
If I start UCM directly by startManagedWebLogic.cmd and not with the WLS console, everything is OK. No error in the log and UCM server is working well
Any idea ?
Thanks
Hugues

Great!
I had the same error: when starting UCM on WL Console, it starts and says Running. But when accessing it on the browser receive the error 404. In the other hand, when starting with Commands, it force shutdowns.
I have set the StartScriptEnabled property to true, now I can start UCM only on the command Line, to start it on WL Console, I have to manually start the node manager.
Is there a way/script to start the node manager automatically?
Regards,

Colour Management Issue with PS CS3 and Leopard 10.5.2

Hi Everyone,
Since I have installed Leopard I am having colour management issues with Photoshop CS3 and my Canon i9950 printer.
My screen is calibrated with a Spyder and I used to ask Photoshop (in 10.4.11) to manage colour when printing and used the Spyder profile. Everything came out as I saw it on screen.
Now in leopard when I do the same thing everything comes out too yellow on the print. If I ask Photoshop to let the printer manage the colour it is too red. If I use the default colour management (photoshop managing the colour and it choosing the colour space it is better, but still too yellow).
Photoshop gives the hint to turn off colour management in the printer but there is no option for this and it also said the same thing before of course (when it worked in 10.4.11).
Any ideas?
Thanks.

>It was working perfectly in Tiger with the monitor profile.
You were lucky.
the monitor profile is so Photoshop can display your images correctly.
the working space is Adobe RGB, sRGB, BruceRGB, ect... these are all known color spaces so when the file goes to another computer there is a consistent color space for reference. If you use your monitor profile as a working space then nobody else knows what is going on with your file.
when you print you need to use the printer profile for the type of paper you are printing on this is supplied by the printer manufacturer. you can also have custom profiles made.
you need to read up on color management:
http://www.gballard.net/psd.html
http://digitaldog.net/

I have a iMac (20-inch, Mid 2009). On start up It will sit at the White screen with the logo and the wheel that spins under it. It will not go past this point? Any ideas?

I have a iMac (20-inch, Mid 2009). On start up It will sit at the white screen with the logo and the wheel that spins under it. It will not go past this point? Any ideas?

Question (?) Mark, Blinking Folder, or Gray Screen at Startup
These are related but not identical issues. Their causes are outlined in Intel-based Mac- Startup sequence and error codes, symbols. Solutions may be found in:
A flashing question mark appears when you start your Mac
Mac OS X- Gray screen appears during startup
In most cases the problems may be caused by one or more of these:
a. Problem with the computer's PRAM - See Resetting your Mac's PRAM and NVRAM.
b. Boot drive's directory has been corrupted - Repair with Disk Utility.
c. Critical system files are damaged or deleted - Reinstall OS X.
d. The disk drive is physically non-functional - Replace the hard drive.
Note that the information I have provided is what Apple recommends, If other users suggest different solutions than found here, then be sure what they recommend does not impact on your warranty, if any, or ability to get continuing Apple service.
Please don't start removing drives or changing cables unless you know what you are doing and have exhausted other non-invasive alternatives outlined here. If you perform any work yourself that is unapproved by Apple, then you will void any warranty you may have and lose all further Apple Support.
Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
The main difference if you are using Lion or Mountain Lion is that you must first boot from the Recovery HD. Simply boot from the Recovery HD to perform the above.
Reinstall Snow Leopard Without Erasing The drive
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install Mac OS X 10.6.8 Update Combo v1.1.
Reinstalling Lion/Mountain Lion Without Erasing The Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

Copying SharePoint Site Page between SharePoint Sites with the MasterPage and Correct PageLayout

Hi All,
I have created a page in the following SharePoint Site Using a Custom SharePoint MasterPage and a Custom PageLayout.
https://devrussellportal.prod.ds.russell.com/sites/emeasandbox/Data-Governance/Pages/DataGovernanceHome.aspx
In this site I have a Page called 'DataGovernanceHome.aspx' in that site. I need to copy this page with the MasterPage and the PageLayout that I have used to build this Site Page to https://russellportal.prod.ds.russell.com/sites/datagovernance/ Site.
The old site is a sub site but the new site is not s sub site. But both them are Publishing Sites.
I was able to copy the MasterPage with all styles and images without any errors and applied successfully to the new site. I exported the desired page from the old SharePoint Site and imported to the new SharePoint Site via SPD. But when I tried to open the
page it gave me an error 'Sorry, something went wrong'.
I even edit the
<mso:PublishingPageLayout msdt:dt="string">https://russellportal.prod.ds.russell.com/sites/datagovernance/_catalogs/Russell SharePoint 3 Column.aspx, Russell SharePoint 3 Column </mso:PublishingPageLayout>
tag by updating the new SharePoint Site URL also. But did not solve the matter. So what is I am missing in here? Could someone help me to solve this matter?
Thanks and regards,
Chiranthaka

Hello,
In your "something went wrong screen" you should see a correlation ID
please run you SharePoint management Shell with this command
get-splogevent | ?{$_Correlation -eq "<GUID>" }| select Area, Category, Level, EventID, Message | Format-List
Replacing the <GUID> by the correlation ID and give us the result
Best regards, Christopher.
Blog |
Mail
Please remember to click "Mark As Answer" if a post solves your problem or
"Vote As Helpful" if it was useful.
Why mark as answer?

How can I print with the black and white cartridge only?

I am trying to print using the black and white cartridge only because magenta is out of ink but I'm getting the following error message in HP Photosmart C7200 series print dialog:
The printer is out of ink.
The following ink cartridges are empty: Magenta. Replace these ink cartridges to resume printing.
How can I print with the black and white cartridge only?
Mac OSX 10.7.3
HP Photosmart C7280 (7200 series)
This question was solved.
View Solution.

I am absolutely disgusted by this; clearly a scam from HP to make more money by selling extra ink cartridges!! I will make sure to never buy any products from the shoddy rip off merchants at HP ever again!!
You should be ashamed!!

Hello, we have both Creative Cloud and Creative Cloud for teams. Can you help me with the difference and if i need to have both?

Hello, we have both Creative Cloud membership and Creative Cloud for team. Can you help me with the difference and if i need to have both? We have 9 employees that are using it. Just not sure if i'm paying for something i don't need.
Thank you

Please refer to Creative Cloud Help | Creative Cloud / Common Questions
CC is for retail use with 20 GB of storage space, CCT is where number of seats are purchased & assigned by one program admin where each seat gets 100GB of storage space.
You can not have both the CC & team in one account as it will only provide you added storage space of 120 GB but you can activate the CC any of them or either of them twice as CC is based on Adobe ID.
Regards
Rajshree

I am doing a lot of presenting with the ipad and want an app that would bullseye or show where I am to my audience. Anyone know of something like this?

I am doing a lot of presenting with the ipad and want an app that would bullseye or show where I am to my audience. Anyone know of something like this?

It sounds like either your hard drive or the SATA cable that connects it to the motherboard are failing. This could be heat related in your case, which is why you see it after it runs awhile. You can take it to the Genius Bar for a free evaluation. If you decide to test it yourself, I usually suggest moving the hard drive to an external enclosure. If it works there for awhile, the cable is probably the issue.
http://www.amazon.com/Sabrent-2-5-Inch-Aluminum-Enclosure-EC-TB4P/dp/B005EIGUD4/ ref=sr_1_3?ie=UTF8&qid=1397647657&sr=8-3&keywords=2.5+enclosure
http://www.ifixit.com/Device/MacBook_Pro_13%22_Unibody_Mid_2009

I have upgraded Apple Aperture from version 2 to version 3 and I'm having a problem with the "Highlights and Shadows" adjustment. According to the user's manual, I should have access to an advanced disclosure triangle which would allow me to adjust mid co

I have upgraded Apple Aperture from version 2 to version 3 and I'm having a problem with the "Highlights and Shadows" adjustment. According to the user's manual, I should have access to an advanced disclosure triangle which would allow me to adjust mid contrast, colour, radius, high tonal width and low tonal width.
If anyone has any suggestions as to how to access this advanced section, I'd be most grateful.

Hi David-
The advanced adjustments in the Highlights & Shadows tool were combined into the "Mid Contrast" slider in Aperture 3.3 and later. If you have any images in your library that were processed in a version of Aperture before 3.3, there will be an Upgrade button in the Highlights & Shadows tool in the upper right, and the controls you asked about under the Advanced section. Clicking the Upgrade button will re-render the photo using the new version of Highlights & Shadows, and the Advanced section will be replaced with the new Mid Contrast slider. With the new version from 3.3 you probably don't need the Advanced slider, but if you want to use the older version you can download it from this page:
http://www.apertureexpert.com/tips/2012/6/12/reclaim-the-legacy-highlights-shado ws-adjustment-in-aperture.html

How do I open GarageBand 09 project with the Amp and Pedals Plugins?

My client sent me via YouSendIt online me his GarageBand 09 v5.0.1 project to tune up Logic Pro 8.0.2. Upon opening the project I receive the message, "Warning! This Project was created by a newer Logic Pro version. This may cause problems. Please update Logic Pro." After I hit "OK", a message says, "Logic Pro: Plug-in “Pedals” not available!, and then "Logic Pro: Plug-in “AmpSim2” not available! Where can I download or get the update that I need for Logic Pro with the Pedals and AmpSim2 Plug-Ins and when will it be available? What other version of Logic Pro is there?

Quoted from Foxboy71:
"aren't the pedals plugs and these new gizmos AU Plugins? Then they should be able to be put into Logic somehow. If not, how did Apple implement them into Garageband (and why!)?"
The folowing excerpts were taken from a Sound On Sound article at http://www.soundonsound.com/sos/aug06/articles/applenotes_0806.htm
"This theory actually plays out, even at the moment, when you consider that every update to Logic includes features to make it compatible with songs created in the latest version of Garage Band. And some of these features have actually benefited the high-end user, such as Apple Loops, in a rare example of the low end driving the high end, as opposed to the other way around."

I was gifted a app store 50$ gift card but it wont let me use it because I'm in the UK store. I can't change my location because of the credit card associated with the account and my phone number please help

I can't change my location because of the credit card associated with the account and my phone number please help

Gift cards are country specific.
They can only be used inside the borders of the country of issue.

Management vlan with the 1000V and UCS

Similar Messages

Maybe you are looking for