MBP unable to recongnize new hard drive

Well to start off I suddenly recieved the "Blinking" ? folder. After taking my MBP to the local genus bar, they weren't able to boot it at all. They told me the HD crashed and I would need to purchase a new HD. I went to Best Buy and bought a WD SATA 500gb HD. I have now installed the new HD, but I am unable to find it in the disk utility. The only (2) items that show up are HL-DT-ST DVDRW GS23N and Mac OS X install DVD.
I have tried powering down several times to see it it might reconginze it without any luck.
I actually bought the MBP at Best Buy and it's covered under a 3 year warranty. Anyone have any suggestions? 
Thanks in advance!
Scott Singer

I think you should have tried to use your installer dvd's Disk Utility first before replacing it just to see if DU could see it at all too.  In fact the so called "genius" should have tried that for you!
But now you've got a brand new disk that DU still cannot see either (I'm assuming you've checked it's properly physically installed).  That would indicate me you have a more serious problem than just a bad disk.  So I would recommend you go back to the "geniuses" and tell them this info and to do a more detailed diagnostic on your machine and fix it (I'm assuming you have applecare).
Update:  If you got that machine at Best Buy and it's under warrantee, then if it were me, and the machine was relatively new, and it was found to have a bad logic board, disk controller, whatever, I would just demand a brand new replacement.  Forget fixing it.  But, hey, that's just me

Similar Messages

  • MBP 15" (late 2008) new Hard drive issues in 10.6.8 but not in 10.8.5

    I have a 15" Macbook Pro (Late 2008) with an up to date EFI firmware (ver 2.8).
    When I went to replace the hard drive (Hitachi 320GB hard wired at 1.5Gb/s) with a new hard drive (Seagate 1TB SSHD).
    This new HD runs at 3gb/s or 6gb/s and my MBP which will only do 3GB/s (link speed) DOES select this speed.
    Now I've read over 1000 posts (no, really) about this topic of SATA drives in older MBP's but problem is a bit more nuanced.
    I partitioned the new HD as follows (disk1-250GB, disk2-250GB, disk3-500GB).  I have to do this because I run two versions of OSX.
    I run OSX 10.6.8 for mobile audio recording and some post-production video editing and my software runs GREAT in Snow leopard.
    Of course, there are some good reasons to have a newer OSX and so I put 10.8.5 on disk2.
    On my old HD I had two partitions (disk1-150GB, disk2-170GB) and then used disk utility to copy the old drive to the new.
    Here's where my problem is more nuanced.  The new drive works AWESOME when running 10.8.5 at 3GB/s.
    In 10.6.8, however, I get pinwheels, beachballs, hiccups, etc when running the hard drive at 3Gb/s. 
    I'll play an aif audio file in Quicktime player and it will stop producing audio, BUT it keeps track of the time.  I swap back in my old HD and everything runs fine.
    I'm planning in getting a different drive (one that works at 1.5 and 3.0GB/s) but I'd like to keep this drive as it boots up 10.8.5 FAST!  In about 15 secs or so.  OR, I could just swap out hard drives when I need to use 10.6.8 (which is really easy on my MBP but not preferable) and dedicate the old one for 10.6.8 only.
    QUESTION:::::
    Does anyone have any idea why the same physical HD would work fine in 10.8.5 but have constant (every 15-20secs) read/write errors in 10.6.8??
    The fact that it works great in 10.8.5 has me a bit puzzled of whether or not there's an inherent hardware incompatibility.
    Sorry for the long post, just trying to give as much info as possible.

    Melophage-
    I did try booting from the external SATA enclosure and all was fine; no hiccups.  I used disk utility to restore my Snow Leopard partition to a newly purchased HD; a Western Digital 1TB(Mainstream) drive that operates at 1.5 or 3.0 GB/s.  I noticed it's power requirement is about 3/4 of the factory drive which is also good.
    Amazingly this drive actually works with a link speed of 3GB/s with 10.6.8.  And no pinwheels/beachballs.
    Possible Conclusions:
    My MBP SATA onboard controller is OK with a HD that's 1.5/3.0 GB/s but NOT quite OK with 3.0/6.0GB/s.  Although both drives had a link speed of 3.0Gb/s, only the newly purchased "slower" drive worked flawlessly.  I'm fine with this being that my Apple factory drive was hard wired at 1.5Gb/sec and its speed was adequate for the audio/video recording I do in 10.6.8.  Hopefully it works fine with 10.8.5.  Still restoring that partition to the Western Digital drive.
    In the end, I have a HD with over 3X the capacity as before and a link speed of 3GB/s. 
    I may not have the 15sec boot-up time as I did with the hybrid drive, but I won't miss it.

  • 3 BEEPS AT STARTUP (MBP 13' late 2011) new hard drive

    HI, I need some help I have changed the hard drive myself of MacBook Pro (the hard drive died after 3 years of intense use)
    (I have a mac book pro 13' from late 2011- 8go ram, 500go hard drive, and i5 double core)
    So, I have now my new clean hard drive inside the baby, and I turn it on, and load the CD of OS X SNOW LEOPARD bought on Apple s website)
    http://imgur.com/ZaAymMr
    Here I have the white screen. I click on the cd icon, and the BEEP BEEP BEEP .... BEEP BEEP BEEP .. And so on, so I force it to turn off.
    WHATS GOING ON??? I've heard that it's a ram issue, I removed it and placed it back up and there is still the issue...
    I you have any idea how to fix that pls tell me, thanks

    3 tones at startup is usually an indicator of a RAM issue:
    http://support.apple.com/en-us/HT202768
    Paulinnn wrote:
    So, I have now my new clean hard drive inside the baby, and I turn it on, and load the CD of OS X SNOW LEOPARD bought on Apple s website)
    If you are using the White retail Snow Leopard disk to install that OSX, it will not work.  I have a late 2011 MBP and that disk and I have tried to do that thus I speak from experience.  (There is a way to install Snow Leopard but not that way).
    The proper way to install the original OSX is to boot the MBP with the OPTION + COMMAND + R keys and follow the instructions.  This will require a solid Internet connection.  (This should install Lion)
    http://support.apple.com/en-us/HT4718
    Ciao.

  • MBP 5.5 can't see my new Hard drive

    MBP 5.5 can't see my new Hard drive even though its running Mavericks off the new Hard Drive through a usb cradle

    I've seen suffienct posts on this site to not argue about the problems with SATA cables, however it sounds like what you're saying is that the SATA cable is bandwidth limited. The types of things I remember reading about are actual breaks in the cable, rendering it useless for all drives, or the insulation wearing off. In the latter, it's on units where the cable crosses over an optical drive and starts intermittently shorting out on the case. If this happens the user typically gets data corruption, but the drive is usually seen and visible.
    On the other hand, I do software development and we have to be able to boot numerous versions of MacOS. For reasons known only to God (and Apple, I hope) once in a while the NVRAM seems to get mixed up and ends up being unable to see the boot drive. Doing the resets always corrects the problem.
    I wouldn't dismiss your recommendation of replacing the cable, but the resets are free and easily done.
    Another freebee to try would be to hold down the "alt' key before powering on the unit, turn on the power, and then, while holding down the alt key, see if the drive shows up as a bootable drive. This will only work if there's an OS installed on the drive.
    In my opinion, it's always best to try the free things before going out and buying anything.

  • Time Machine: New Hard Drive Unable to be "formatted"?

    Dear community,
    I apologize for this post, I searched a little but aside from the current TM bug, I had a hard time finding an answer to this question. I'm also re-installing on my other laptop so I am unable to reproduce this SNAFU.
    I recently ungraded my hard drive on my mid-2008 unibody Macbook, now running 10.8.4 (first of the unibodies!). I finally outgrew my 160 gig hard drive and bought a 500 gig WD Caviar Black. I created a TM restore on my old backup, and installed the new hard drive into my mac and restored from my back up (2 days ago). This isn't like the current bug that's going on at this time, I was able to see and restore from the most recent TM point.
    Today, I had to force a close secondary to a run away process (Sophos) that was overheating and taking up my processes. I was unable to force quit, so I did a hard reset. At this point, I got the gray screen of death and was unable to progress past the Apple Logo. Safe booting proved that there wasn't any problem mounting the disk and everything would point to some sort of corrupt process.
    When I got home from work, I used disk utility repaired permissions, but was unable to progress past the Apple Logo. I used a NEW back up disk last night to back up my TM to make a restore point, and I was going to just restore the whole computer from that. Unfortunately, I had an error when I attempted to restore from the TM backup.
    Essentially, it was able to initiate the back up, but within the first 15 seconds it would stop and say something similar to "...Unable to restore from Time Machine back up, the new hard drive is unable to mount/install restore software/image. Please restart to attempt again..." Apparently, it's rare to have this problem, my googling did not find many recent occurances.
    Thus my night has been this:
    -- Disk utility x2 on the newly installed hard drive
    -- Repaired permissions and verified disk (both checked out), the first time the permissions were changed (--r--x--w to something)
    -- Reformatted the disk w/ zoroes x1
    -- Reattempt to reinstall from TM (with the same error)
    I wish I grabbed screens, but I was a bit frustrated. Right now, I am re-installing ML from the web and then attempting to use the Migration Assistant to restore from these Time Machine back ups. I had around 15 gigs of pictures moved onto the new machine last night (hence the back up last night). So, I'm pretty good with terminal, so I'm not going to be shy about poking around.
    Any suggestions? Thoughts? I am much obliged for your input.

    So, right after I try to restore I get this message,
    "An error occurred while adding a recovery system to the destination disk. Restart your computer and then try restoring again."
    This is very vague.

  • How should I format and partition my two new hard drives in a 2010 MBP?

    My good old mid-2010 13" MBP just lost its stock hard drive. I've decided to keep the laptop, set aside the defunct drive for future data recovery and pop two new drives in the computer along with a 8GB ram upgrade (two 4g ddr3 chips).
    The two drives I'm working with now are a 256GB Crucial MX100 SSD (intended for my OS and startup) and an HGST 1TB Travelstar (for apps and storage) that I'm popping into the optical bay [via conversion tray].
    I'm putting everything together myself then taking the build to tekserve (or the apple store? which should I go to for OS re-install and formatting help? ) to re-install my original OS (snow leopard) or mountain lion. i cant find my recovery disks and also can't download mountain lion on another comp. to boot my laptop build with.
    Is it okay to just throw the drives in myself and let pros format them for me? I know i should be installing the OS myself but all of my workaround options are fleeting due to time constraints... gotta get my OG setup up and running.
    Thanks everyone.

    sageakash,
    I have the same model MacBook Pro as you. If the 1 TB Travelstar HDD is a SATA III disk, then you might have trouble with it in the optical bay due to the connecting cable. To minimize problems, put a SATA II disk rather than a SATA III disk into the optical bay.
    If you want your MacBook Pro’s original iLife apps to be installed on your new disks, then you’ll need to have Snow Leopard installed first, even if your target OS is Mountain Lion; they can’t be subsequently installed from the grey Applications Install DVD once a newer version of OS X is on your boot volume.
    What is your concern with pros formatting your disks? What’s “OG”?

  • UNABLE TO INSTALL pHOTOSHOP eLEMENTS ONTO A NEW HARD DRIVE

    I am unable to install my Photoshop Elements onto my new solid state hard drive

    Thank you for replying. Sorry for the caps.
    I am trying to reinstall Elements 10 on Win 7. I have a new hard drive. I can install Organizer but not Editor. It rolls back after trying to install Editor. I do not have the exact error message handy.
    I have done an exhaustive review of the symptoms and applied the suggestions in every thread but no luck .
    I downloaded a trial of Elements 13 which worked. Then I tried to install Elements 11 but without success.

  • Copy MBP Hard Drive to new Hard Drive while FileVault enabled?

    Is it possible to copy MBP Hard Drive to new Hard Drive while FileVault is enabled?  Also, what's the best way to image from a 700GB drive to a 300GB SSD?  I'm currently using 250GB.

    Hi, have you tried the Boot Camp forum ?
    personally I think it should work...L

  • Unable to install clean Recovery & Application/drivers on new hard drive

    My HDD failed on Satillite P25-s526. I replaced it with OEM new drive. Also upgraded the RAM from 512mb to 2GB's. I have attempted to do a full recovery of the system using DVD which came with the computer.  DVD formats partitions in new HDD, loads the restore tool & downloads. Upon completion, Restore Tool indicated 100% complete. Recovery Disk removed when indicated & system states "Please wait while windows prepares to start...". After a short while, the screen goes dark but the HDD indicator light indicates it's still processing. After a short period, the computer does nothing! I have left it on for at least 1 hour to see if it would reboot. Nothing! Upon restart, I do not get the Toshiba splash screen & the OS starts with the Windows XP/SP1 screen and then the screen goes blank! Boot to Safe Mode loads and then a pop up indicated that only part of the OS loaded and to reload. I have done this twice with the same results. Any ideas on what to try next?   

    Thank you for your quick response. I have been able to confirm that the new hard drive is in fact, the exact model and nominclature as the original (MK8025GAS HDD2188). I have also rechecked that I installed it correctly, since the HDD can be configured as both master or slave.  SET UP acknowledges the hard drive and it's capacity.The Rec & App/Drivers DVD appears to be in good working order.  I have been assured by the manufacturer that the HDD supplied is the exact replacement to the original and is not have ATF.
    Toshiba trouleshooting for this HDD states that reports of systems not being able to recognize all available capacity of this hard drive & offers two 3rd party suggestions to correct the issue. They are EZ DRIVE by Micro House and Disk Manager DiskGo by Ontrack. Unfortunately, neither would do me any good since I cannot install them in the computer present condition. Further more, I'm not sure that they would help since SET UP indicates formatted Capacity of 80.012GB.
    I was running Vista SP3 when the HDD crashed, I wonder if the drivers etc. have not reverted back to their original configuration with the Rec & App/Drives Disk?  Grasping for straws now!

  • Installed new hard drive and windows 7 at the same time. Left old hard drives in computer but unable to get bookmarks from old drives to new.

    Installed new hard drive and windows 7 at the same time. Left old hard drives in computer, installed firefox however I have no idea in which file the old bookmarks are located. I still have the old files for firefox in the old drives.

    Your "Firefox personal data", like bookmarks, are stored in your Profile folder in Firefox. See this support article about how to recover that data from that old hard drive and transfer it your your new Profile.
    http://support.mozilla.com/en-US/kb/Recovering+important+data+from+an+old+profile

  • Unable to restore time machine backup onto a new hard drive

    I recently bought a new hard drive for my mid-2010 white Macbook. I have kept this computer regularly backed up with time machine, but just to be sure I made sure I hooked up my external hard drive prior to changing the hard drive and made sure it was fully backed up. I checked my exceptions and saw that my system files and applications were listed, so I removed them from the exceptions list and let it back up again (it only backed up a further 60MB though, so that made me a little uneasy).
    I successfully switched over the hard drive and then plugged in my external hard drive so I could do a restore from Time Machine. My external hard drive has 3 partitions: 2 time machine backups for each of my computers, and one partition for storing files that also has an old copy of 10.6 on it.
    When I booted the computer, I held option, then selected Macbook TM. When it came to the window with 4 options, including disk utility and restore from time machine backup, I selected restore from Time Machine backup. When I did so it said "No OS X Backups Were Found." Why wouldn't it have backups listed if I have been consistently backing it up? How else do I do a full system backup?
    Also, how can I be sure that I'm restoring this backup onto the new hard drive? It didn't prompt me to select that drive at any point, and I want to make sure I'm not overwriting the middle partition on the backup drive (or anything else).

    Please visit Pondini's Time Machine FAQ for help with all things Time Machine.
    You will find that Mountain Lion stores an invisible copy of the Recovery HD. You can boot from your Time Machine backup drive by restarting with OPTION boot:
    Boot Using OPTION key:
      1. Restart the computer.
      2. Immediately after the chime press and hold down the "OPTION" key.
      3. Release the key when the boot manager appears.
      4. Select the disk icon for your Time Machine backup drive.
      5. Click on the arrow button below the icon.
    Your computer should boot into the Recovery HD. You will be presented with a main window of options. Select the option to restore from a Time Machine backup then click on the Continue button.

  • New Hard drive doesn't show up (MBP late 2009)

    I have a 2009 Macbook Pro that was running Lion. The HDD failed so I installed a new one. This blank HD had no OS on it so I get the blinking question mark (the problem that started it all). I found my old snow leopard disk and tried booting from the disk. Each time I tried this I got hung up on the screen that just shows an apple and a little swirly time thing. I also tried booting holding option so that I could select exactly what I wanted to do. When I tried this, I noticed that there is no HDD showing up next to the picture of the disk. I know this is not normal because on my (working) iMac, it shows both my hard drives and the snow leopard disk. I recently went to the "Genius" bar where they performed a diagnostic. The test showed that the SATA cable, logic board, and HDD were all in place and properly functioning. I have already reformatetd the new hard drive through target disk mode on my iMac. I have no idea what else to try. I've let it run for several hours and all I get is an apple with the swirly time thing and a very hot laptop.

    Hold down Option while you start up. Only the DVD will be shown, because the new drive is not yet bootable.
    Choose the DVD and click the proceed arrow. It should proceed within one minute.
    "A Mac that cannot boot from an appropriate System/Utilities DVD has a Hardware problem."
    You should soon get the "What Language ?" screen and be able to proceed to Install.
    If you cannot Install because of the Drive, answer only the What language question, and WAIT a quarter minute for the MenuBar to be drawn, then choose Disk Utility from the Utilities Menu.
    Make sure the new drive is present, and has GUID Partition Map and a Mac OS X Volume in Mac OS X Extended, Journaled.

  • Installing a new hard drive in my MBP

    I have outgrown my hard drive and want to upgrade. When I put in the new hard drive, what is the best way to transfer my data/settings from the old one? I keep everything backed up using Time Machine, and I've seen some posts that say it should be no problem restoring the system from the TM backup. I ask, though, because I have also read a few posts that seem to indicate that Migration Assistant might be easier, or at least better at transferring settings from user accounts. I've never done this before and want as little hassle as possible in doing it, so I'm hoping someone with more knowledge on the subject can clue me in as to which will be better/easier...

    If you have a TM backup then that would be more reliable than Migration Assistant.

  • Permission issues with new hard drive

    Apple installed a new hard drive on my fairly new (june2012) MBP. The only backup I had was the time machine backup from the old MBP that I originally migrated from. Apple said no worries - I can restore from that so I did.
    Today I bought an iphone. (I was a hold out, I'm all things mac since the 80s except the phone). I went in to clean up my Contacts before syncing the new phone to my MBP and I couldn't delete and contacts or groups. So I did a "get info" on my contacts ap and it didn't even have (user/me) on the list as a user. I added myself, gave me the read and write" capability and still can't make the needed changes, deletions or anything in Contacts, so I decided to check permissions using Disk Utility. I repaired permissions, and just to be sure verified permissions again. What a lllloooonnnggg list of issues and nothing has changed. Hit "repair permisions again and it is taking f o r e v e r. Now I am Verifying Disk to see what it says. No problem. Verify Permissions again - did it faster, but still a bunch of problems found. Repaired permissions again - same old thing - says its repairing, but I seriously doubt it. Am I supposed to do this over and over again?
    Suggestions???

    Back up all data. Don't continue unless you're sure you can restore from a backup, even if you're unable to log in.
    This procedure will unlock all your user files (not system files) and reset their ownership and access-control lists to the default. If you've set special values for those attributes on any of your files, they will be reverted. In that case, either stop here, or be prepared to recreate the settings if necessary. Do so only after verifying that those settings didn't cause the problem. If none of this is meaningful to you, you don't need to worry about it.
    Step 1
    If you have more than one user account, and the one in question is not an administrator account, then temporarily promote it to administrator status in the Users & Groups preference pane. To do that, unlock the preference pane using the credentials of an administrator, check the box marked Allow user to administer this computer, then reboot. You can demote the problem account back to standard status when this step has been completed.
    Triple-click the following line to select it. Copy the selected text to the Clipboard (command-C):
    { sudo chflags -R nouchg,nouappnd ~ $TMPDIR.. ; sudo chown -R $UID:staff ~ $_ ; sudo chmod -R u+rwX ~ $_ ; chmod -R -N ~ $_ ; } 2> /dev/null
    Launch the Terminal application in any of the following ways:
    ☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
    ☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
    ☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
    Paste into the Terminal window (command-V). You'll be prompted for your login password, which won't be displayed when you type it. You may get a one-time warning to be careful. If you don’t have a login password, you’ll need to set one before you can run the command. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
    The command will take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear, then quit Terminal.
    Step 2 (optional)
    Take this step only if you have trouble with Step 1 or if it doesn't solve the problem.
    Boot into Recovery. When the OS X Utilities screen appears, select
    Utilities ▹ Terminal
    from the menu bar. A Terminal window will open.
    In the Terminal window, type this:
    res
    Press the tab key. The partial command you typed will automatically be completed to this:
    resetpassword
    Press return. A Reset Password window will open. You’re not  going to reset a password.
    Select your boot volume ("Macintosh HD," unless you gave it a different name) if not already selected.
    Select your username from the menu labeled Select the user account if not already selected.
    Under Reset Home Directory Permissions and ACLs, click the Reset button.
    Select
     ▹ Restart
    from the menu bar.

  • Have Old Hard drive and want to move old data onto new hard drive in imac.

    I am trying to get my files off of an old hard drive. I have it hooked up through a sata drive. I am able to access all the programs but for whatever reason I am unable to access any of the files, i.e- 1,00's of pictures, videos, music, and documents. Is there something else I need to do in order to get the files, or is it possible that all the programs could still be on it but the files are just missing? In the current Sata it only has two plugs but on my hard drive it looks like there is another place to plug something in.

    Hello again Shadow,
    The way I do this is to:
    1) Install your new hard drive into your iBook
    2) Get your iBook reassembeled
    3) Place your old hard drive in your firewire enclosure
    4) Insert your install DVD into your iBook and restart with the C key held down. When the installer launches, select your language in the first pane, click 'continue' and in the upper dropdown menu in the next page select Utilities > Disk Utility. After DU is open, select your hard drive from the list of volumes on the left (the very top one), and then click the 'Partition' tab to the right. Then select 1 partition (normal) and make sure that you have 'Mac OS Extended (journled)' selected in the lower section. Then click 'partition'
    5)Quit disc utility, which brings you back to the installer. continue with your installation of OS X. In one of the first steps you will see a button on the lower left which says 'options' click on that and make sure that the option 'Installs OS X for the first time' is selected. It will normally be selected by default with a new drive.
    6) After the installation, the Migration Assistant will ask if you would like to transfer your information from another mac. click yes then follow the instructions. but instead of using another mac, connect a firewire cable from your enclosure with your old hard drive installed. The installer will think that this is another mac and will transfer all of your account information and user files (everything!)from your old drive to your iBook's new drive. Just diconnect when it says to and complete the installation sequence.
    You're done!
    Check back again if anything is unclear.
    Randy
    Message was edited by: DesertSage

Maybe you are looking for