Message received "error initializing output device"

I receive a message "error initializing output device" even after downloading the driver from HP that HP recommended. I had this error when I first bought Windows 7 and ended taking it off line and putting my old one with Windows XP back on line. My old printer (a Dell printer) worked with it. I bought a new HP printer and was sure it would work with Windows 7, but it doesn't. How can I fix Windows 7 so I can get rid of this frustrating error and make the printer work?

Hey jack0501, I see you are having an issue of device being busy and will not respond to print commands. There are a few steps I would advise performing to see if this can be resolved. First, I would advise performing a Hard Reset to the printer, restart the PC, and power cycle the network if this printer is network connected. Follow these steps to reset your HP printer, your wireless router, and your computer.Press the Power button on the HP printer to turn it off.Disconnect the power cord from the rear of the HP printer.Disconnect the power cord from the wireless router.Turn off the computer.Wait 30 seconds.Reconnect the power cord to the wireless router.Wait 30 seconds, or until the router is fully on and ready.Turn the computer back on.Wait for the computer to reload.Reconnect the power cord to the rear of the HP printer.Turn the printer back on.**Subsitute unplugging the USB cable for power cycling the Router if it is USB connected. Second, I would advise restarting the Print Spooler service on your PC after everything is power cycled and logged back in. Below is a link to a thread on restarting the print spooler service. http://h30434.www3.hp.com/t5/Printing-Issues-Troubleshooting/Restarting-the-Print-Spooler/td-p/2447413 Try to print again after performing these steps and let me know how it goes. Jason

Similar Messages

Error message received - Service 'Apple Mobile Device' (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services.

I've done it 6 times the steps you mention to get this thing to work but still it doesn't work for me. I've downloaded iTunes, installed it, and again the same message it's going on Error message received - Service 'Apple Mobile Device' (Apple Mobile Device) failed to start. Verify that you have sufficient privileges to start system services.
I've deleted iTunes, Apple Mobile Device Support, Apple Software Update and Bonjour, restart my computer and downloaded again (6 times) and still doesn't work for me. What should I do?

I deleted all Apple products you mentioned above (iTunes, Apple Mobile Device Support, Apple Software Update and Bonjour), deleted the prior downloads I had previously tried to install and then emptied my recycle bin. Then I started with a new download of iTunes before the problem was solved for me.
It really ***** that Apple does not give any direct support for its own products.
Good Luck

Good morning, AdobeSuite installation does not work and I receive"error initializing program, download adobe advisor" error message. On Adobe site it appears"The Adobe Support Advisor has been discontinued The Adobe Support Advisor tool was used to analy

Good morning, AdobeSuite installation does not work and I receive"error initializing program, download adobe advisor" error message. On Adobe site it appears"The Adobe Support Advisor has been discontinued The Adobe Support Advisor tool was used to analyze installer log and system information associated with installation errors. The tool has been replaced with improved installation support mechanisms. Please visit Adobe Support section for Knowledge base articles around Installation."

Nobody can tell you anything without proper system info or other technical details. We don't even know what exactly you are trying to install.
Mylenium

Product name- HP Pavilion g6 notebook pc. showing message of "no audio output device is installed".

Product name- HP Pavilion g6 notebook pc with windows 8 preinstalled. After configuring windows update audio device is not working and message of no audio output device is installed is shown. Error code 52 is showing when i tried to troubleshoot with control panel. Please help with steps to re-configure audio device properly.

Hi Ravi2602,
Thank you for visiting the HP Support Forums and Welcome. I have read your thread on your HP Pavilion g6 and no audio. Here is a fix from Microsoft. Right click the speaker icon in the taskbar and select Playback Devices. Left click Speakers and Headphones, click the Set Default button. Restart the computer.
I would be happy to assist if needed. How Do I Find My Model Number or Product Number?
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Update termination Error : Maintain Output device in User master record

Hi All,
For transaction IW32 when print is given we have getting Update termination error : Maintain Output device in User master record.
I have set the user_settings = Space, for output_Options passed the output device . Even for control_paramters I have passed the device while calling the Smartform . However there is no use. Still I am getting the update termination error.
Please let me know how to solve this issue. Any OSS Note is there for this.
Thanks in Advance!
Regards,
Preethi G

Hi,
Thanks for the reply. There is no problem in the print program .
In the user master record , if the output device is not given and in the print program if we pass the output device. the error is coming.Is there any way to solve the issue at the print program level with out maintaining the user master.Please let me know.
Many Thanks!
Regards,
Preethi G

CUA: SCUG - Transfer Users errors with Output Device does not exist

Greetings,
I'm currently setting up CUA on our ECC 6.0 boxes and ran into an issue when I run SCUG and try to transfer the users. We're in the process of upgrading to ECC. The target systems are upgraded copies of our current 4.7 target systems.
Currently we have CUA connecting to our DEV,TEST, PreProd, and Prod Systems.
The output devices only reside on the target systems. There are no output devices on our production CUA box.
I'm trying to setup the ECC CUA box and modeling all the settings to our current environment. Once I set the CUA setting, including the RFC's and ALE connections I ran scug and ran into the issue.
I only get the error where the Default Output Device is populated. Users with no Default Output transferred without any issues. I looked up notes in OSS and can't seem to find any on this subject.
Side note: If I remove the output device it transfers without error. Obviously this is not a solutions, I was merely testing out the scenario.
Any help would be greatly appreciated

Hi Alex,
there is just a little comment in SAP note #399917 (point 4).
As from my knowledge, the SCUM settings are not considered during SCUG. So setting
'output device' to local will not be a solution.
The standard way is to transport the ouput device information to your CUA-master system before taking over the users. (create transport in SPAD).
I have also another workaround for you gurus, but this will need to modify the standard coding for the time of taking over your users. Using this modification, only a warning message will appear and unknown printers will not be taken into CUA-master system.
Pls test this proposal carefully (coding is rather old....), this is just a suggestion !
Include LSUUCF01
FORM DEFAULTS_CHECK
Spool: Ausgabegerät
IF NOT DEFAULTSX-SPLD IS INITIAL AND
     NOT USER_DEFAULTS-SPLD IS INITIAL.
    SELECT SINGLE * FROM TSP03 WHERE PADEST = USER_DEFAULTS-SPLD.
    IF SY-SUBRC <> 0.
      PAR1 = USER_DEFAULTS-SPLD.
      CALL FUNCTION 'BALW_BAPIRETURN_GET2'
           EXPORTING
                TYPE       = 'W' "'E' "Warning instead of error
CL         = '01'
                NUMBER     = 29
                PAR1       = PAR1
          IMPORTING
               RETURN = ERRORTABLE
           EXCEPTIONS
                OTHERS     = 1.
APPEND ERRORTABLE.
    ENDIF.
ENDIF.
I strongly recommend to undo this modification after you have finished SCUG.
Good luck, b.rgds, Bernhard

No Audio Output Device is installed error message

I have a hp pavilion m6- 1045dx and when I turned it on I noticed there was no sound and the speaker icon next to the clock in the bottom right corner had a red "x" next to it. I tried pressing the mute button, up volume, and down volume buttons and that didn't work. I've tried power cycles, uninstalling and re-installing and even downloading new drivers, checking for software changes, and checking to see if software and things pertaining to this problem were up to date (windows said yes). My frustration level is through the roof and I'm ready to get rid of this laptop. Can someone please help?

Hi ALima,
With the error message of No Audio Output Device is Installed. I have included the document 'Error in Windows 7: No Audio Output Device is installed'. Please follow through the troubleshooting steps in order for the best results.
If the above document fails to resolve the issue, I have also included 'Troubleshooting Audio Problems with External Speakers, Headphones, and HDMI Sound Devices'.
Please let me know if you are still getting the same error message after troubleshooting, thank you.
I worked on behalf of HP

Output device not defined error while saving the quotation

Hi all,
We have some custom output types (ZGEN, ZSSO, ZQTO, ZJT)configured in the nace transaction for Application V1. Whenever i am creating / saving a quotation one of the output type(ZQTO) is not processing for mail (External Send) and it is displaying an error as 'Output device not defined'. If i remove all the output types while changing the quotation in VA22 from header, it is processing.
I checked with all other output types combination. The error is trigerred only when we have ZJT output type along with ZQTO.
We are not able to recognise the error. Please help out to solve this issue. Its very urgent.
Thanks.

Hi Remi
Thanks for your reply. As per your reply I followed procedure and it allowed me to save Basic Pay Infotype (0008)
Thanks a ton.
Regards
Prakash Bhave

Maintain output device in user master data

when we try to print the Purchase order smartform we are getting the
following update terminated error message.
" Please maintain output device in user master data".
1. If we maintain output device in my user profile as any printer name
then we are not getting the update terminated error message.
2. when we select the network printer it is always printing
using the output device maintained in the user profile (example
LOCL). it is not printing using network printer.
when we select the network printer it should overwrite the user profile
output device.
Can we have the network printer selected irrespective of the printer
maintained in the user profile?
Please provide the solution
Title was edited by:
Alvaro Tejada Galindo

Hi
If you mention printer as LOCL the system will use network printer and the printer will be controled by Windows.
If you specify printer name the printer will be controled by SAP.
I hope now you can re-analyze your issue.
Regards
Surya.

HP Pavilion DV6604NR "no audio output device is installed"

my laptop is HP Pavilion dv6604nr with windows vista OS. Suddenly, the laptop lost its audio. the error message is "no audio output device is installed". i searched the internet and HP websites for possible solution and have done all including reinstalling the OS to factory settings but it does not resolve the problem. at the same time, it cannot detect the DVD player too

Hi,
Check if you have performed all the steps mentioned the links below and also run the microsoft fixit. If you have done all these steps then most likely a hardware issue..
Resolving No Sound or Audio Problems (Windows Vista)
Error in Vista: No Audio Output Device is Installed
Note:
If you have HP Support Assistant installed on the computer(The Blue Question Mark) then open it ==> Complete all pending Updates & Tuneups==> Restart and Check. It may solve your problem
Although I am an HP employee, I am speaking for myself and not for HP.
**Click on “Kudos” Star if you think this reply helped** Or Mark it as "Solved" if issue got fixed.

Error parsing output

Hi There,
New to the Java World and Im getting the following error when submitting this java program for compilation and output. Output is Via a html page
// just import the BufferedReader and inputstream reader
import java.io.BufferedReader;
import java.io.InputStreamReader;
class addtwonumbers
    public static void main(String[] args)
    // system.in reader (e.g. the input from the console)
    InputStreamReader ISR = new InputStreamReader(System.in);
    // buffer the console reader
    BufferedReader BR = new BufferedReader(ISR);
    // the default values for the two numbers
    int val1 = 0;
    int val2 = 0;
    try
        // output the question.
        System.out.print("Enter two Numbers:\n");
        // read in the console intput one line (BR.readLine) and then convert to a integer
        val1 = Integer.parseInt(BR.readLine());
        val2 = Integer.parseInt(BR.readLine());
    catch (Exception ex)
        //if the input was a string.
        System.out.println(ex.toString());
    // output the answer of adding both of the values together and * by 3
    System.out.println("The result is " + (val1 + val2) * 3 );
The error message is "Error parsing output, please try again"
Thanks In advance.
Edited by: Conor O'Neill on Mar 16, 2009 4:11 PM

>
Conor O'Neill wrote:
> Hi Ayyapparaj
>
> Thanks for getting back to me: yes I already have done what you suggested and it works fine, but I'm trying to output in an HTML page (in a table).
Hi,
What you mean by HTML page(in a table)?
Code what you have written above is a pure application that need to be run in the way i have mentioned above.
If you are interested to create a HTML page where you can enter two numbers and print their out put. You need to change the code altogether.
Regards
Ayyapparaj

Output device is locked

Dear all,
GRIR Clearing background job was cancelled due to the following error.
Output device LPxx is locked in the SAP system.
Could you please let me know how to find out this error?

Discuss with your basis team about opening the printer.
Sounds like it was in use before.
Regards
Hein
P.S. trasnaction spad for printer maintenance, but better to check with oyur colleagues

HT1923 receiving error 7 windows error 126

I have deleted and reinstalled itunes and keeping getting the message receiving error 7 windown error 126. Looking at the comments via apple support i'm not getting any where. Also not clear why this has happened now having had itunes for a few years now!

Hey FloridaGerbil,
Thanks for the question. The following article outlines Error 7, and may help resolve your issue:
iTunes for Windows: "Error 7" message when opening iTunes
http://support.apple.com/kb/TS3074
Additional Information:
iTunes 11.1.4 for Windows: Unable to install or open
http://support.apple.com/kb/TS5376
Thanks,
Matt M.

SRT 031 Empty SOAP Message received

Hello,
I have an external Web service wich it works under SOAPui, but when I generate a Proxy and a port in SAP using the WSDL file , and then i try to test it I have this error message.
SOAP:1 031 SRT: Empty SOAP message received
How can I solve this problem?
Thanks in Advance.

Hi Jitendra,
We are having similar problems, we're getting the SRT 031 Empty SOAP Message received error but the RFC destination is set up OK.
Running the same webservice from other tools gets a response OK, so the issue must be on the ABAP/SOAManager side of things
Do you have any more ideas of how to troubleshoot this?
Thanks in advance
Tony

Home Media Server - Error Loading Supported Device...

I have recently installed the Home Media Server application that came on the DVD with my N82, onto my PC.
However, I am unable to 'see' my N82 as a device. When I select, Add new Devices I get an error message stating 'Error loading Supported Devices - please check your internet connection.
I thought that this may be a Firewall issue but Home Media Server is listed in my Firewall as accepted.
Any thoughts would be appreciated
History: Always Nokia since 1994 including Nokia 2140, 7110e, 6150, 6210, 6310i, 6230i, N82
Current: Nokia N8 (Anna - I have no intention of going to Belle) - and delighted with it!

Have you tried searching the forum? I remember quite a few people had this problem a few years ago.
Make sure you search the entire forum, not just the N series board as I think the answer is in one of the other more appropriate boards.
Use the keywords "home media server". Answers that apply to other models like the N95 should also apply to the N82.

Message received "error initializing output device"

Similar Messages

Maybe you are looking for