Mouse problems after 11/29/05 Security Update?

I installed the 11/29/2005 Security Update 2005-009 via Software Update. Right afterwards (even before the required reboot), I began having mouse oddities. The cursor disappears from the screen, or just stays there and doesn't move. Moving the mouse won't make the cursor move. I must click the mouse before the cursor "wakes up" and responds to the mouse. It's fine after that.
I'm using a Logitech cordless optical mouse. Batteries are fresh and this only begain right after installing the Security Update. Anyone else experiencing this?
[ Edited by Apple Discussions Moderator; added update ID 2005-009 ]

I have resolved the issue! As I mentioned, I am using a Logitech cordless optical mouse. I connected up my Apple keyboard & mouse and disconnected the Logitech. The problem no longer occurred with the Apple mouse.
I removed the batteries from the Logitech mouse and disconnected the USB receiver. Restarted the computer, reconnected the Logitech setup, disconnected the Apple stuff, and now it is working.

Similar Messages

  • Problems after the last Apple Security Update with trackpad/mouse tapping/clicking

    Dear All,
    I do have a MacBook Pro 15 (early 2008), Mac OS X (10.6.8). The logic board was replaced a couple of years ago under Apple warranty (distorted video problem). I am planning to repalce it after the next apple update on the macbook pro line. Before someone asks, I am using Snow Leopard because I still have some programs that needs Rosetta. I did apply the last security update and after I did shutdown and restarted the computer last night, the trackpad/mouse (mighty mouse, usb mouse) is not working properly. I just cannot do the left click or tap on the trackpad. The mighty mouse works perfectly, except the clicking. The same for the trackpad (tapping). I manage to open a pdf file with some keyboard shortcuts. I can use the mouse/trackpad to scroll and zoom in/out the document. I can use the trackpad to rotate the document, etc. Pressing on the might Just can´t tap/clock on the document to select or open it.
    I alread did the obvious thing: command-alt PR, start in safe mode, unplug the power/battery for a few minutes...
    Did you have a similar problem with the last security update. Do you have any suggestions.
    Thanks,
    Carlos

    I have resolved the issue! As I mentioned, I am using a Logitech cordless optical mouse. I connected up my Apple keyboard & mouse and disconnected the Logitech. The problem no longer occurred with the Apple mouse.
    I removed the batteries from the Logitech mouse and disconnected the USB receiver. Restarted the computer, reconnected the Logitech setup, disconnected the Apple stuff, and now it is working.

  • Ethernet speed problem after OS 10.4 security update

    I have a G4 iMac and a G4 Powerbook both running 10.4.11. The iMac is on an ethernet cable and the powerbook connects wirelessly through an Airport Express to a Dynalink ADSL2+ modem/router and both used to work fine... until the recent security update.
    Having solved the 'Another application has changed your network settings' on the iMac (using this thread: http://discussions.apple.com/thread.jspa?threadID=1730909&tstart=0), I still have an ethernet problem on both machines.
    Network connection will now only work with ethernet manually set to 10baseT, when before automatic worked fine. That includes the Airport. Copying files between the G4 machines and printing using the Airport Express as a usb print server is all mega slow.
    Tried setting modem/router back to default settings but that hasn't solved it.
    My MacPro running 10.5 has had no problem. Any ideas please anyone??

    Hi Roger, and a warm welcome to the forums!
    On that cure... did you just lock the Security settings, or did you also trash those pliss, an'or make copies of your Locations & delete the old ones?

  • Each time my iMac reboots i am prompted to enter my FaceTime password.  This just started occurring after the most recent security update.

    Each time my iMac reboots I am prompted to enter my FaceTime password.  This just started occurring after the most recent security update.  When I put my password in the pop up just comes back, if I press cancle it goes away.  Any ideas on how to get rid of this annoying popup?

    I had the same problem. Try this. Launch FaceTime. Click the toggle to turn it off; or Command-K. Quit. Do a restart, you shouldn't get the popup. You could then turn FaceTime back on if you wish. Either way, the popup should be gone from then on.

  • Loss of FN-Keys after installation of Microsoft security updates on L500

    I'm using a satellite L500-19U
    After installation of Microsoft security updates the FN keys lost their functin except the Brightness + / - function.
    also the soft keys which appear at the upper monitor border by pressing the FN key didn't appear after the security packages were installed.
    I solved The problem by removing the update by means of the roll-back function (Wiederherstellungs punkt) of W7.
    The following security packages are selected to be installed:
    Security update for Windows 7 for x64-based Systems (KB978601)
    Security update for Windows 7 for x64-based Systems (KB979309)
    Security update for Windows 7 for x64-based Systems (KB979683)
    Security update for Windows 7 for x64-based Systems (KB980232)
    Security update for Windows 7 for x64-based Systems (KB981332)
    Windows MRT x64 - April 2010 (KB890830) (malicoius software removal tool)
    Which of them are unsuspicios, which shall be posponed, which updates are necessary after installation of the updates?
    Message was edited by: JoJo58

    hi,
    If you read about these update on the Microsoft site: (Non of them should influence on FN-Keys)
    http://www.microsoft.com/downloads/details.aspx?displaylang=en&FamilyID=998164b7-4b8c-468b-8d39-f242633c8838
    I have checked the history of updates on my computer and all of them are installed except for Windows MRT x64 - April 2010 (KB890830) (malicoius software removal tool). Everything works fine, try to remove this update.

  • IMac G5 freezes on start up after ITunes, Quicktime and Security update

    On June 2nd, the following event occurred on my IMac G5 (model year 2005) equipped Mac OS 10.4.9
    Upon completion of the automatic update for Itunes, Quicktime and a security update, the computer restarted.
    However, the start-up sequence freezes on a grey screen with the logo for the power button displayed in the middle and a message inviting to hold down the poer button down for 5 sec to re-start.
    the only way to complete the start up sequence is to hold down the apple key while pressing the power button.
    Does anyone have any suggestions to regain control of my computer ?thank you in advance.

    Welcome to Discussions - Hopefully, you repaired permissions both before and after updating, if not, it might be a good thing to do now. Also, you are not alone in having problems with the update, take a look at this.
    Generally, it's better to install updates one by one, so that if you have problems, you know which one caused them.
    Miriam

  • After installing recent java + security update, computer will not sleep

    After installing the recent java, daylight savings, and the security update. my computer will not sleep. Does anyone else have this problem? I do have an adaptec usb2 card installed but nothing is plugged into it. Also i don't have any Ipods or external things plugged in. I have had the same setup for the past year with no problems, now it will not sleep. I have also tried repairing the permissions. Please help

    When you select Sleep from the Apple Menu nothing happens, is that correct? Try this: Go menu > Home > Library > Preferences. Drag the whole of the Preferences folder to the desktop. Restart your mac, don’t worry if things look different, you have not lost anything. Can the mac sleep now? If yes, then its a damaged or corrupted .plist or preference. If you are using Apple Mail, drag the com.apple.mail.plist back to the new preferences folder created on reboot, you dont really need anything else but keep hold of the old preferences (the one you dragged to your desktop) just in case for a month or two. If everything else is OK you can safely delete it. If it has not cured the problem then remove the new preferences folder created on reboot by taking it to the trash, drag back the preferences folder you moved to the desktop and reboot. Now reinstall a clean OS. See how you go from there

  • Login status Error after install of new security update on 3-11-15

    I am having this issue only after I installed the latest Security update. Now I am unable to install the iMovie update, or log into the app store.

    As Patrick says Apple having server issues since early AM at least.
    As I posted else where…
    Hey everyone with Apple problems right now…
    Apple is having server problems affecting App Store, iTunes, iCloud, etc…
    Check the Apple Service Status(***) page… http://www.apple.com/support/systemstatus/
    Wait for all systems green. This is always a good idea if you have problems with anything Apple.
    Here is what Apple message says…
    Multiple Store Services - All users are affected
      Customers may be unable to make purchases from the App Store, iTunes Store, iBooks Store, or Mac App Store.
    iCloud Mail - All users were affected
      Users may have been unable to access iCloud mail.
    iCloud Account & Sign In - All users were affected
      Users may have been unable to sign in.
    This means no downloads, updates, iCloud and other issues. You may get pop-up windows asking you for password for iCloud, etc…
    Wait, try again after all go to go on *** page.
    Hope this helps, Greg

  • Mac Mini won't boot after applying 2009-001 Security Update

    I'm stuck at the gray startup screen with the Apple logo and the "gear wheel" progress indicator. Still stuck there after 60 minutes of "letting it brood."
    How to I fix this?

    The easiest way to solve the problem is to restore the drive from the backup you made just before installing any update or software on your computer, then do the installation again following the suggestions at the end of this post. Failing that...
    First, try the routine repair disk and repair permissions with Disk Utility on your installer disc. Boot from the installer disk, select language if applicable, choose utilities, run Disk Utility and verify (and repair if necessary) the drive. You can verify a drive from DU on your main drive while booted but I have found this can result in incorrect reporting of errors. To repair your drive you have to run it from a drive other than the boot drive anyway.
    Next, boot from your drive in [Safe Mode|http://docs.info.apple.com/article.html?artnum=107393] and repair permissions. You can repair permissions while booted from the installer disc but this uses the permissions configuration on the installer disc which may be out of date if you have run any updates on your computer. Booting your computer to Safe Mode restricts the number of things running on your computer while permissions are being run and done a bit of spring cleaning at the same time.
    [Resolve startup issues and perform disk maintenance with Disk Utility and fsck|http://docs.info.apple.com/article.html?artnum=106214]
    [Using Disk Utility in Mac OS X 10.4.3 or later|http://docs.info.apple.com/article.html?artnum=302672]
    [Disk Utility's Repair Disk Permissions|http://docs.info.apple.com/article.html?artnum=25751]
    From BDaqua (couldn't have said it better):
    "Try Disk Utility
    1. Insert the Mac OS X Install disc that came with your computer (Edit: Do not use this disc if it is not the same general version as what you have currently on your computer, e.g. use a Tiger disc for a Tiger drive, not a Panther disc), then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
    Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
    3. Click the First Aid tab.
    4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
    5. Select your Mac OS X volume.
    6. Click Repair. Disk Utility checks and repairs the disk.
    Then Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes."
    If you don't have an installer disc available you can try effecting repairs using [fsk in Single User Mode|http://docs.info.apple.com/article.html?artnum=106214].
    [Post by japamac about using fsk|http://discussions.apple.com/thread.jspa?threadID=1649143&tstart=0]
    If the above don't work, two things seemed to be solutions for Security Update 2008-008 problems.
    One is Archive and Install which will replace the corrupted system but then requires you reapply all your updates. Select the keep settings and preferences when doing A&I. Make sure you select that option when doing A&I if you want settings and preferences kept. Some third party applications may need reinstalling if they have special components.
    [Mac OS X: About the Archive and Install feature|http://support.apple.com/kb/HT1710?viewlocale=en_US]
    [X-Lab Archive and install|http://www.thexlab.com/faqs/archiveinstall.html]
    [Kappy's A&I instructions|http://discussions.apple.com/thread.jspa?threadID=1823034&tstart=0 ]
    [How to get files from a previous home directory after Archive and Install|http://docs.info.apple.com/article.html?artnum=107297]
    The other is to try to re-install the security update on the main drive while booted from a secondary drive or in Single User Mode. This could be from another Mac computer while your first one is in Target Disk Mode, perhaps a bootable backup drive, or possibly from your installer disc. Here's references for those methods:
    http://discussions.apple.com/message.jspa?messageID=8728797#8728797
    http://discussions.apple.com/message.jspa?messageID=8733921#8733921
    http://discussions.apple.com/thread.jspa?messageID=8634535#8634535
    Updating
    There's been recent discussions as to what steps are truly necessary in doing a minimal problem update.
    I think #1 to which all agree is to make sure you have a backup of your computer in case you do need to back out of it again.
    Some like to boot from their installer discs or an external backup and verify (and if necessary repair) their internal drives as well as drive permissions. This is done with Disk Utility. You can verify a drive while booted from the same drive but sometimes this produces spurious errors. Repairing a drive (if necessary) has to be done while booted from another disk. Permissions repair can, and is probably best, done when booted from your internal drive.
    [Resolve startup issues and perform disk maintenance with Disk Utility and fsck|http://docs.info.apple.com/article.html?artnum=106214]
    [Using Disk Utility in Mac OS X 10.4.3 or later|http://docs.info.apple.com/article.html?artnum=302672]
    [Disk Utility's Repair Disk Permissions|http://docs.info.apple.com/article.html?artnum=25751]
    You can also go to the step of booting into safe mode to do the install.
    [Mac OS X: Starting up in Safe Mode|http://docs.info.apple.com/article.html?artnum=107393]
    [What is Safe Boot, Safe Mode? (Mac OS X)|http://docs.info.apple.com/article.html?artnum=107392]
    [Safe Boot takes longer than normal startup|http://docs.info.apple.com/article.html?artnum=107394]
    I like to download the update onto my computer and install it from there rather than let Software Update do it. I know a few people who had problems with doing the update via software updater found a manual install to work.
    Repair permissions again afterward.
    It also helps to only install one update at a time and to run the computer for a while to make sure it is behaving well.
    Almost all of the above steps (except backup) have been questioned as to necessity because probably many people have done successful updates without doing them. I say they can't hurt, they can very likely do good (especially if your computer isn't regularly maintained), so why not do them to be safe.
    [BDaqua's comments on updating problems|http://discussions.apple.com/message.jspa?messageID=8948595#8948595]

  • After Firefox did a security update yesterday, I cannot stream Netflix. It is not any of my addons because I disabled them and still cannot stream.

    I can no longer stream Netflix after the security update. I keep on getting a system requirements message form Netflix. It worked fine before the security update and I can stream on IE.

    -> Create a New Profile as a test to check if your current profile is causing the problems.
    -> Basic Troubleshooting: Make a New Profile
    * https://support.mozilla.com/en-US/kb/Basic%20Troubleshooting#w_8-make-a-new-profile
    -> If that New Profile works then you can recover your Bookmarks and Passwords from the Old Profile.
    -> Recovering important data from an old profile
    * https://support.mozilla.com/en-US/kb/Recovering%20important%20data%20from%20an%20old%20profile
    Check and tell if its working.

  • IPod dead after carrying out RECOMMENDED security update!  Any ideas?

    At the beginning of December 2006, I installed the most up to date version of iTunes when prompted to do so. I was then informed by iTunes that my iPod required a security update and so I downloaded this update. My iPod (5th Generation model) seemed to freeze half way through the process. It keeps attempting to load and then crashing when I try to switch it on. The iPod is now no longer being recognised at all by My Computer. I tried all of the recommended troubleshooting steps and advice with no success.
    My iPod now doesn’t even turn on properly and given that the PC doesn’t recognise there is a device attached to it, we cannot take any of the troubleshooting steps to fix it.
    If changes had been made to the PC, these may have caused the problem and I could have looked at some troubleshooting solutions such as tweaking with the PC registry, updates of drivers etc. However, it is clearly not a PC issue as I have tried to plug the iPod in to three PC’s with no success. The iPod hard drive no longer starts so I'm 99.9% certain it is an issue with the iPod hard drive – the security update has essentially scrambled/killed the iPod hard drive and it seems to need to be completely reset. I have tried the '5 R's' and that did not work. I also managed to get the iPod into diagnostics mode and it says it has issues!
    I have had absolutely no problems whatsoever with my iPod prior to attempting this security update (which was recommended by Apple). The iPod has therefore mal-functioned through no fault of my own – if I hadn’t been prompted to download this security update, I have no doubts that it would still be in good working order.
    Any ideas!!
    PS - this essential security update and subsequent death of my Ipod occurred exactly one day after my 1 year warranty expired!! Call me a cynic but do I smell a rat?
    5th Generation iPod Video 30GB   Windows XP  

    My problem started after downloading 3.1.2. It gave an error message that said it could not install the program due to an error. It gave me the option of sending the error message to Apple. I declined. My ipod now only displays a screen that shows a usb cable being plugged into itunes. The computer will not read it and it will not sync. My ipod is basically dead. Ive tried all of the fixes to restart it but have had no success. Holding down the power and home button did not work. I held it for nearly 20 seconds. The power will shut off then the apple will appear. Then the usb cable appears again. I purchased my ipod on 10-1-09. Im going to take it back for an exchange.

  • Mac Pro (early 2008) black screen after 2015-004 Mavericks security update

    Hi,
    My Mac Pro (early 2008) does not start up after 2015-004 security update last week. I can't
    get anything on my monitors.  I can hear it starts booting, but not sure if does so fully, because the screen
    stays black.  Have tried all the different booting options, e.g. safe boot, but no effect.  Is there a way to revert
    the update or even do a clean OS install, even if I can't see anything on the monitor? 
    I just noticed that Apple has released a supplemental update today for Yosemite 10.10.3,
    "that will fix video driver issuesthat will prevent your mac from starting up when running certain apps that capture video"
    I am wondering if this is my problem, even if I use Mavericks.  Any thoughts?

    Try booting to Recovery and repairing the the startup disk via Disk Utility.
    OS X: About OS X Recovery - Apple Support
    Next try resinstalling the OS
    OS X Mavericks: Reinstall OS X

  • Sunfire X2250 endless restarting after putting on all 'security' updates

    Hello all, yeserday I did a fresh Solaris install and once that was done i ran updatemanager. I selected only the 'security' updates. They downloaded and then installed. I then got a screen prompted me to reboot, so i ticked the box and let the machine do its thing. So the machine goes through and installs the remaining patches and the reboots. Upon reboot right after grub where i select Solaris to boot i get the Sun solaris copyright screen and right after that a bunch of 'unknown symbol' messages all over the place. The machine doesn't even get back to the desktop or login and enters maintenace mode. I was stuck at this point, I didn't know what to do and couldn't go any further and so I did a complete reinstall of the OS again. Once it came back up I again ran updatemanager and selected only the 'security' updates. It did the same thing again! upon the shutdown/reboot sequence the system hangs again, endless reboot loop. Why are these basic security patches messing up the machine? is there a known bad patch that bonks everything? I now have everything reinstalled again (3rd OS reinstall) and it's running great but i'm scared to run the patches again. Can anyone please help or provide an explaination? thank you very much in advance

    Thanks for your reply, scapesuiter.
    I suppose i can rule out third party software, as, after i reinstalled my OS after the first freezing (after 2007-003), i did not add anything else. At that point there was nothing on my computer but what came on the original install disks. I tried downloading and installing 2007-003 again and the same thing happened, and i had to reinstall again.
    However, i do have 1GB RAM that i did not order from Apple. My computer originally came with 512 but i bought more some time ago (can't remember exactly when).
    I also bought a new hard drive, also not from Apple, at around the same time.
    But i should say again that i've had no problems since getting the new hardware, other than with these particular security updates (2007-003 and 2006-007). All the other security updates went well, as well as all other software updates.
    (I also did a hardware check with my Apple Hardware Test disk and it indicated that everything was working fine.)
    PowerBook G4   Mac OS X (10.3.9)   Ti 800MHz 1GBRAM 100GB Internal Drive

  • After downloading the latest security update of lion 107.3, I lost the app store and when attempting to download anything lion I receive a plug in failed message?

    after downloading lion security update 10.7.3 I lost the app store and when attempting to download anything lion I receive a plug in failure message, what is the fix?

    Download a fresh Firefox copy and save the file to the desktop.
    * Firefox 4.0.x: http://www.mozilla.com/en-US/firefox/all.html
    * Firefox 3.6.x: http://www.mozilla.com/en-US/firefox/all-older.html
    * Uninstall your current Firefox version and remove the Firefox program folder before installing that copy of the Firefox installer.
    * Do not remove personal data if you uninstall the current version.
    * It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
    Your bookmarks and other profile data are stored elsewhere in the [http://kb.mozillazine.org/Profile_folder_-_Firefox Firefox Profile Folder] and won't be affected by a reinstall, but make sure that you do not select to remove personal data if you uninstall Firefox.

  • IBook G4 won't start up after installing promted itunes & security update

    HELP.
    My iBook G4 was prompted to update iTunes & some security update. I always do this when prompted, and restart as requested.
    I installed the updates and restarted, but this time my iBook won't boot up. It makes the regular chime noise, goes to the gray screen, gets past the apple logo, then goes to a blue screen with the cursor in the upper left corner. The cursor moves just fine, the caps & num lock lights work, but it just never gets past the blue. If I leave it alone for a while, the cursor disappears, and I get the turning circle in the lower middle of the screen (the one that comes up during the gray screen). It just sits and sits on the blue. Hard drive isn't making any unusual sounds.
    I tried starting it up from the Install Disc, which worked fine. I ran the disk utility and it said it didn't need any repairs.
    Still won't start up.
    I did the cmd + opt + p + r to get the 3 chimes... no change.
    I tried the fsck thing, it didn't do anything.
    HELP.
    Am I a goner?
    I saw that some other people had problems, but it seems like everybody's is just slightly different. My display looks totally normal, just won't get past the blue screen. My disk utility said that it didn't need any repairs? Looks like most other people at least saw some errors in there...

    I think Carolyn misunderstood the "3 chimes" comment. I think what you meant was that you held down the key combo until you heard the normal startup chime for the third time, not that the iBook gave you the 3 long beeps of a failed POST (power-on self test) which could indeed indicate a RAM problem.
    It's more than likely not a RAM issue. These bad updates occasionally happen and the way to handle it is to do what you're doing now; backup what you can and then do an Archive and Install of the OS (although usually a couple of reboots, start in safe boot mode and reinstall the update is usually all that's needed).

Maybe you are looking for