[Mplayer] Blue screen with TV Out

I can view movies ok with the latest Mplayer 1.0pre8-1. But when I use TV Out, the movie is totally blue. I can't see anything, just plain blue screen. The sound is working ok then. Running gmplayer from a console does not give any different output when TV Out is enabled or disabled.
Have X.org 7.1 with NVidia drivers 8774, GeForce 4 MX videocard. In xorg.conf I have two metamodes: Option "MetaModes" "1024x768, ; 1024x768, 1024x768" so I can switch between monitor only and TV. So with only the monitor everything is ok, as soon as I switch to the MetaMode with TV on the movie goes blue.

SenorSnor wrote:using another video driver (from mplayer preferences) solved it.
Which one?

Similar Messages

I just powered on my mac book pro and have a blue screen with a flashing folder with a question mark in the middle, how do I get out of this?

I just booted my mac book pro and it is at a blue screen with a flashing folder with a question mark in the middle of it. How do I get out of it?

Click here and follow the instructions. If the computer was running Mac OS X 10.6.8 or earlier and you reach the third set of steps, insert a Mac OS X install disk.
(126818)

When trying to save page in Yahoo! Bookmarks, I receive blue screen with message:A problem occured while trying to save bookmark. Please try again later. I get the same message every time.

When I click on Yahoo Bookmark Icon & click on Save this page,
I get the normal screen Save To My Bookmarks, etc. I fill out as
normally & click save. That is when I receive blue screen with above message. Frustrating because it lets me go through the process but then will not save. Is this a cookie or privacy issue??

At the top of yahoo bookmarks there is a message:
To Yahoo! Bookmarks users:
Yahoo! Bookmarks is transitioning and will be exclusively available via Yahoo! Toolbar. During this transition, you will be able to access your bookmarks in read-only mode.We expect the transition to be fully complete by October 20, 2011, after which you will have access to your bookmarks with the ability to add/ edit/ delete bookmarks.
Please download Yahoo! Toolbar for a full bookmarks service. We sincerely apologize for any inconvenience during this period.
But the toolbar dosn't work either, even after it is updated, so we may just have to wait.
Hope this helps :)

Blue screen with the following error SYSTEM SERVICE EXCEPTION (ACPL.sys)

Hi,
I had a blue screen with SYSTEM SERVICE EXCEPTION (ACPL.sys) error message yesterday.
It happened right after the graphic card update was completed. I have an HP Spectre XT laptop with Windows 8 and Intel(R) HD Graphics 4000.
After restart, I noticed that the available free space on my hard disk dropped by 4 GB!
Can you please assist?
Thank you.

We do need the actual DMP file as it contains the only record of the sequence of events leading up to the crash, what drivers were loaded, and what was responsible.
WE NEED AT LEAST TWO DMP FILES TO SPOT TRENDS AND CONFIRM THE DIAGNOSIS.
You may be able to get the DMP files without crashing by booting into safe mode (F8) with networking.
If you are overclocking stop. (chances are if you dont know if you are, you are not)a
To enable us to assist you with your computer's BSOD symptoms, upload the contents of your "\Windows\Minidump" folder. We need at least 2 DMP FILES to diagnose and confirm
The procedure:
* Copy the contents of \Windows\Minidump to another (temporary) location somewhere on your machine.
* Zip up the copy.
* Attach the ZIP archive to your post using the "paperclip" (file attachments) button. (if available on your site, MS doesnt have this)
*Please upload them to a file sharing service like Skydrive or"Rapidshare" and put a link to them in your reply.
Link for how to upload below.
http://www.wikihow.com/Use-SkyDrive
To ensure minidumps are enabled:
* Go to Start, in the Search Box type: sysdm.cpl, press Enter.
* Under the Advanced tab, click on the Startup and Recovery Settings... button.
* Ensure that Automatically restart is unchecked.
* Under the Write Debugging Information header select Small memory dump (256 kB) in the dropdown box (the 256kb varies).
* Ensure that the Small Dump Directory is listed as %systemroot%\Minidump.
* OK your way out.
* Reboot if changes have been made.
Please also run MSinfo32 and upload the output as well.
To run MSinfo32 please go to start>run>MSinfo32
Go to "file" "save" and upload the saved file with the DMPS
System specs are extremely useful so please include whatever you know.
Blue Screen View & Who Crashed are often wrong and should only be used in an emergency
Team Zigzag3143.com
Wanikiya & Dyami--Team Zigzag

Blue screen with error message

Product Name: HP Media Center M7250n Desktop PC
Product #ED842aa-aba
I have been getting a blue screen with error messages that ask if this is the first time i get the error and then at the end it says it is dumping memory. I would like to wipe my harddrive and reinstall XP but my system is out of warrenty and HP won't provide me a recovery CD. What are my options.
This question was solved.
View Solution.

Hi,
You are most welcome.
"I work for HP."
Please click the "White Kudos" star to say thanks for helping.
Please mark "Accept As Solution" if my help has solved your problem.

Macbook Pro 10.6.8 won't shut down. Blue screen with spinning wheel.

it's an 15 inch macbook pro. since I bought this computer was working fine about last year. Somehow, start of this year, the problem begins. Everytime when i opened microsoft word 2011 on mac or Photoshop cs5, and quit the software as normaly. When i try to shut down the blue screen with spinning wheel apears. this spining wheel is endless. But funny thing is that after use other software such as games, web browser (safari) etc. and quit them. when i shut down there was not a problem. only word 2011 for mac and adobe photoshop cs5. Any solutions?

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Console in the page that opens.
Step 1
Select "system.log" from the file list. Enter "BOOT_TIME" (without the quotes) in the search box. Note the timestamps of those log messages, which refer to the times when the system was booted. Now clear the search box and scroll back in the log to the last boot time when you had the problem. Post the messages logged during the time something abnormal was happening. That time might be before or after the boot.
For example, if the problem is a slow startup taking three minutes, post the messages timestamped within three minutes after the boot time, not before. If the problem is a system crash or freeze, post the messages from before the boot time, when the system was about to crash or was failing to shut down. In either case, please include the BOOT_TIME message at the beginning or the end of the log extract.
Post the log text, please, not a screenshot. If there are runs of repeated messages, post only one example of each. Don’t post many repetitions of the same message.
If the log doesn't go back far enough in time, scroll down in the Console file list to /private/var/log/system.log.0.bz2. Search that archived log, and if necessary the older ones below it, for the same information.
Important: Some private information, such as your name, may appear in the log. Edit it out by search-and-replace in a text editor before posting.
Step 2
Do the same with kernel.log.
Step 3
Still in Console, look under System Diagnostic Reports for crash or panic logs, and post the most recent one, if any. In the interest of privacy, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please don’t post shutdownStall or hang logs — they're very long and not helpful.

My touchsmart will not boot allI get is a blue screen with f key to do different things

My Touch smart desk top will not boot when I turn it on all I get is a blue screen with HP in the center and f key functions

Hello charleshobby:
Your computers start up has been corrupted. No big deal. Turn on your computer hold down on F-8 key as you turn it on. This should put you in safe mode. If f-8 key fails then just disconnect the power cord at the power adapter and plug it back in and turn on your computer (This is called a fource start up) automatically puts your computer into safe mode. Use your arrow kek select safe mode with net work. Top one I belive. In safe mode close out Help and Support window displayed. Open up Recovery Manger and select Microsoft System Restore. Click next then click next again now a list of dates will appair choose a date before this event occured. Click next and let your computer complete the sytem restore. My guess Microsft up dates caused this issue. After this is finished now go back and change all your update setting to down load up dates but let me choose witch ones to install. Only install three at a time. To a void future occurances and black screen or blue screen issues. Follow these steps for blue screen or black screen. Please click on Kudos if this has resolved your issue. Thank you frrw.

Blue screen with cursor at boot. And everything after that.

Dear Forums,
(Please note, I'll refer to the machine as a Server, but it is only using 10.4 client; I am merely using the Sharing capabilities of such).
I have a MDD G4 that I'm using as a server. When I start it up, I get the Blue Screen with Cursor (BSwC) at boot - and it never goes past that. (Can't move the cursor either).
I have read the articles
http://docs.info.apple.com/article.html?artnum=106464
And Dr. Smoke's
http://www.thexlab.com/faqs/startupitems.html
http://www.thexlab.com/faqs/repairprocess.html
I've also tried AppleJack and clearing out caches, zapping PRAM, etc. All the standard fare.
It will boot into safe mode just fine, and it is still acting as a server just fine.
I have also tried Multiple Users (to no avail).
I tried a reinstall of Tiger, which, interestingly enough, didn't give me the option for Archive and Install and Preserve, but instead only gave me the option to Upgrade (hm, from Tiger to Tiger). While this fixed nothing, the server continued to work after this.
Then I had the bright idea to install the OS to the 2nd drive I had within. 'Surely this would work,' I thought. But alas. It did not. In fact, clean installation, new disk, (and yes, I booted from this 2nd disk), the same BSwC problem.
So, please, Dear Apple Support Discussions, let there be someone out there smarter than I (I'm really not that smart, but I do follow instructions well).
-Ty

How long did you wait for the blue screen to go away? I also have a iMac G5 2GHz ALS.
My computer has been having a problem where on the first boot of the day, it it would hang in the gray screen for about 1.5 minutes and the blue screen for about 4 minutes. I thought it was permanently hung but discovered that it would eventually present the login screen. I could then login normally but none of my firewire external drives would mount. I could restart over and over and the same situation would be present.
Resetting the SMU seems to cure the problem and rebooting would be quick and all firewire drives mounted correctly. I could then reboot as many times after and normal behavior of the iMac would be repeatable.
However after having the system down for several hours and restarting it, the problem would be back.
I have now moved all my firewire drives to a powered hub and will watch over the next day or so to see if that changed anything.
Robert

Can I use a blue screen with Final Cut Pro X?

Hi, I am at a school that uses Macbooks and has just purchased a blue screen (with lighting). I am new at chromakey / blue screening. I know that you can use iMovie for green screens, but could somebody please tell me what is a good software to use for a blue screen? Does Final Cut Pro X work with blue screens?
If anyone has any advice I would be very grateful!!
Thanks,
From Michelle.

The keyer effect in FCPX works very well with blue screen. Open effects browser and look for Keyer. When you add it to your blue screen clip it will automatically pick up the blue screen and key it out. You also have several controls to fine tune the edges etc.

IQ500 Blue screen with no response

I have a HP Touchsmart IQ500 that is a little over a year old. It was working fine and I went out one day to come back and start it up to find it was only a blue screen with a few options.I found someone with a similar problem and they explain it better so here is the problem:
The system booted up to the blue screen with the HP and Intel logos and four options listed which were: <F10=Setup>, <Esc=Boot Menu>, <F11=System Recovery>, and <F9=Diagnostics>.
Pressing either F10 or Esc resulted in the messages "Entering Setup..." or "Loading Boot Menu..." respectively but the system immediately freezes. Pressing either F9 or F11 has no discernable effect at all.
Pressing Ctrl+Alt+Delete, pressing the power button, or hard-cycling the power all have the same effect of bringing me right back to the blue screen.
There seems to be no computer response to anything I do, besides the blue screen being there. I also cannot get the computer to start in safe mode, since I also tried that.
I would greatly appreciate any help as I have a lot of personal items on the computer I would hate to lose. Thank you for any help!

Yes .. it might be a hard drive problem. And not a very fun kind of hard drive problem. I was thinking about this thread alot last night... trying to figure out any other possible problem. There is also the lesser possibility that it might be heat related damage to the motherboard, memory, graphics card, or processor... but these types of issues usually show up as intermittent lockups and freezes.
THe easiest fix I can think of, for someone who is not all that computer-savvy, is to replace the hard drive. THis sounds hard, but it is pretty easy on TouchSmarts. Before you start, you must have a set of ecovery discs if you want the software to be the same as when you bought it.
If you don't have discs, you can order a set from HP for minimal cost.
Once you have the recovery discs, you simply swpa out the hard drive with power unplugged...put everything back together and insert the first recovery disc into the PC to start the recovery process.
steps to replace HD...
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01498883
... an HP employee expressing his own opinion.
Please post rather than send me a Message. It's good for the community and I might not be able to get back quickly. - Thank you.

Why is my MacBook Pro **crashing** changing to a blue screen with lines or distorted screen when I open logic or Ableton Live

Why is my MacBook Pro **crashing** changing to a blue screen with lines or distorted screen when I open logic or Ableton Live. Then I have to restart by long pressing the power button. Can somebody plz help me

What you describe sounds like a hardware issue. Unfortunately, you'll need to get that checked out by Apple. If you have an Apple Store near you, make an appointment with the Genius Bar and take the machine in for evaluation.

My MBP 15 inch can't switch off (freeze at blue screen with spinning wheel)

Whenever i try to "shut down" my MBP, it will freeze at the blue screen with the spinning wheel (that keeps spinning like 'eternally')! Any idea how to solve the problem?
I tried booting from the installation disk and repairing disk with "disk utility" but to no avail. Have also tried repairing disk permissions... Any idea how else should i tackle this problem?
Currently i can only switch off my MBP by holding the power button (forcing it to shut down)...
Please help Thanks!

Launch the Console application by entering the first few letters of its name into a Spotlight search, and select "system.log" from the file list. Enter "BOOT_TIME" (without the quotes) in the search box. Note the times of the log messages referring to boot times. Now clear the search box and scroll back in the log to the time of the most recent boot when you had the problem. Look for error messages in the minutes before that time, and post them here -- the text, please, not a screenshot. Edit out excessive repeats, if any. Do the same with kernel.log.
If the logs don't go back far enough in time, scroll down in the Console file list to /private/var/log/system.log.0.bz2 and /private/var/log/kernel.log.0.bz2. Search those archived logs, and if necessary the older ones below them, for the same information.
Also in Console, look under System Diagnostic Reports for crash or panic logs, and post the most recent one, if any. For privacy’s sake, I suggest you edit out the “Anonymous UUID,” a long string of letters, numbers, and dashes in the header of the report, if present (it may not be.) Please do not post shutdownStall or hang logs -- they're very long and not helpful.

Picture shows in library but when i open develop it shows a blue screen with a diaginal cross

picture shows in library but when i open develop it shows a blue screen with a diaginal cross

Go to the Preferences>Performance tab and uncheck the "Use Graphics Processor" option. Adobe are aware of this issue, and are investigating, but in the meantime unchecking that option should sort out your Develop module issues.

Blue Screen with spinning coloured wheel

My girlfriend borrowed her iMac G4 Flat Panel to a friend and now it won't load the OS properly.
The following happens:
1. The grey screen appears (with the smiling MAC in the middle)
2. The Mac OS X start-up screen appears with the progress bar
3. Then a blue screen, with a spinning coloured wheel in the top left corner
4. After a couple of minutes, a few windows pop open (probably whatever the person accessed last)
5. The windows disappear and all you're left with is a blue screen and spinning coloured wheel in the top left corner
6. The MAC then remains in this state indefinitely
Unfortunately, I’m unable to tell what version of the MAC OS is running.
We cannot find the OS disk either.
I will greatly appreciate any assistance anybody is able to provide.
Thanks

Brannas...
Empty,Blue Screen.
http://docs.info.apple.com/article.html?artnum=106464
1. Start up in Safe Mode.(shift key at startup)
a. Drag the Fonts folder from the Mac OS 9 System Folder (not the Mac OS X System folder) to the desktop.
b. Drag the Fonts folder from ~/Library/Fonts to the desktop.
b. Restart the computer in Mac OS X.
c. If this solves the problem....you have a corrupt font in one of the above font folders
2. Remove incompatible third-party startup items.
a. Start up in Safe Mode.(shift at startup)
b. Open the Mac OS X hard disk.
c. Drag third-party items out of ....
/Library/StartupItems .......
/System/Library/StartupItems ...
Place them on the desktop .... If you're unsure whether an item is a third-party item or an Apple-installed item, don't move it.
d.Restart the computer.
Note.. If this resolves the issue, add the Startup Items one at a time until the symptom occurs again. That way you'll know which one is incompatible. Repeat these steps and remove the incompatible item.
3. If your computer still starts up to a blue screen, follow these steps.
a. Start up using cpmmand+S....(Single-User Mode).
b. Type: mount -uw /
c. Press Return.
d. Type:
mv /Library/Preferences/com.apple.loginwindow.plist preferences2.old
Tip: There is a space between ".plist" and "preferences".
e. Press Return.
f. Type:
mv /Library/Preferences/com.apple.windowserver.plist preferences3.old
g. Press Return.
h. Type: reboot
i. Press Return.
4. Reset certain privileges.
a. Start up the computer in Single-User Mode.
b. Check the volume with fsck.
c. Type: mount -uw /
d. Press Return.
e. Type: chmod 1775 /
f . Press Return.
g. Type: reboot
h. Press Return.
george

Reset PMU and Powerbook won't boot past the blue screen with "Mac OSX" box

Hi-
Problem: I tried to reset my PMU, and now when my computer restarts it won't go past the blue screen with the "Mac OSX" logo in the box (and progress bar, that never fills up). I then also tried to reset PRAM, but it still won't boot properly.
Backstory--
I've had my 12-inch Powerbook G4 for about 3.5 years already, so things are starting to get a bit out of whack. I replaced my battery about 3 months ago, which has been great, but recently my power-cord has been wonky (having to unplug it and replug it in to make sure it actually charges the computer, the light flickers on and off, etc). Today it actually started producing SPARKS at the place where the thin white wire meets the white plastic power brick, so I decided it was time to get a new one. Brought it home, plugged it in, and since it seemed like the battery indication icon on the menu bar was all out of sync with the powercord colored-light, I tried restarting it a few times, but still the same. Then, I decided to reset the PMU, which may have been a huge mistake. And now it won't boot past the blue screen... Any advice? I'm going to try restarting it in "safe" mode, but I'd be so grateful for any recommendations. Hope I haven't done something irreversibly stupid with the PMU reset.
Thanks,
Samantha

Hello all,
Thanks for all of your great suggestions and info-- here are a few responses.
1) The disk I just borrowed from my friend appears to be the full retail version-- it looks just like the links that Ali B sent, and is in a large box saying "Mac OSX Tiger, version 10.4"... will this be the proper disk to do an Erase and Install? The only other disks I have came with my Powerbook when it was originally purchased, when it came Panther (I think, 10.3?). Would I use both sets of these disks to do erase and install? Or only the Tiger OSX disks?
2) I get the sense that Disk Warrior or Tech Tool might be necessary, but does it make sense to TRY to do erase-install before buying them? Also, are there any downloadable (for pay) versions of this, or would I need to track down the actual physical disks in Hong Kong or wait for them to be shipped?
3) I haven't yet tried the S.M.A.R.T. test, should I do that first? What is the procedure? Are there any results or ways to know if the drive is too far gone (so that I might instead replace the internal hard-drive) instead of pay 100 USD first to do the disk repair?
4) Cornelius said: "An alternative would be to completely reformat and erase the entire HDD, then re-install and restore your data from backup. If your backup is in the form of a bootable clone of the entire HDD, you can just clone it back." I use Super-Duper to back-up and the most recent one copied the whole thing-- what would be the later procedure of "cloning it back"?
5) As I'm able to use my computer pretty normally right now, but does it still mean that it might crash/die at any moment? Is there any way to tell?
Thanks so much!

[Mplayer] Blue screen with TV Out

Similar Messages

Maybe you are looking for