My ethernet cord won't stay in because of a slight dent on my macbook pro- will applecare cover this?

my macbook pro has a slight dent near the ethernet cord plug and it changed the shape of the hole so that the cord wont stay in. will applecare fix this for me?

There's a pretty narrow margin between the plug fitting in the port properly, fitting loosely, and not fitting at all (meaning the opening is too small). Someone "might" be able to get the shape just right for you, but it'd be a fairly difficult task. While the aluminum does bend somewhat, it isn't all "that" flexible. It's possible that someone could break a chunk right off if they need to bend it more than just a slight amount or if they need to move it back and forth a bit to get it just right. The problem I see is that the connector should be snapping into the "port", not the frame. It sounds like your port itself may be damaged.

Similar Messages

13 Macbook Pro the ethernet cord won't stay plugged in.

My ethernet plug will not clip in. I plugs in and it works, but it will just slide out on its own. It doesn't click in. I have tried different cables and it doesn't make any differences. I have look at the female part of the plug and it doesn't appear that their is anything wrong with it. Anyone have any suggestions?

I have the same problem. I can verify that there is nothing wrong with the ethernet cable, as it "clips in" fine in 3 other computers that I own. Even the slightest movement dislodges the cable. I have tried several different cables, even buying an expensive cable with a premium jack, all to the same result. I believe this is a product defect, but as it's the only Macbook Pro that I own, I don't know if it's something with product design. This is a brand new 13" mid 2012 Macbook Pro.

Mid 2010 Macbook Pro will not stay off or asleep

Hi,
I have a mid 2010 MacBook Pro will not stay turned off when I tell it to shut down. It will shut down just fine, but a few seconds later it will boot up again. This also happens when I try to close the lid (or just put it to sleep), it will work fine, screen/Apple logo on the back will turn off and the status LED will slowly pulse. However a few seconds later, the LED stops pulsing and the Apple logo will illuminate. If I open the lid I will be greeted with the log in page with zero delay (i.e. its been displaying for a while).
This has become problematic because the computer always be running. If I put it in my laptop bag the computer will get hot as ****. The only way to get it to really turn off is to let the battery die or remove the battery. But this computer does not have the externally removable battery so that is not a trivial process.
The symptoms exist in both Mac OS (Mountain Lion and Maveriks) and Windows 8/8.1. This makes me believe its something in the hardware (or at least a setting in the hardware), not software (I know Apple doesn't care what Windows does, but it is exibiting identical behavior).
I have reset the NVRAM and the SMC with no luck. When I reset the SMC I didn't get a good indication that anything happened though, and was wondering if that is normal. Resetting the NVRAM results in another restart, while its hard to tell if you actually reset the SMC. I reset the SMC by turning the computer off, then holding the power button when it tries to restart (this usually gives me a few minutes where the computer will actually stay off), then pressing shift, control, option and power at the same time and releasing them at the same time. This is how the Apple documentation said to do it. They did not mention how long the must be held though so I presume that doesn't matter.
Anyone experience this/have any ideas?
Thanks,
Jim

Btmm error "can not coonnect to cloud server" Facetime and IMessage " Could not sign in, check your network connection and try again". Which I have again and again...

My macbook pro will turn on but screen stays black.

My macbook pro will turn on but screen stays black. There is no sound on start up and keys dont light up. I have done all the resets:
I disconnected the computer from the power cord, and from all other cables.
I held down the power button for several seconds to turn off the computer.
I let it sit 5 minutes.
I restarted the laptop while holding down the Shift key and nothing happened.
Holding down Command, Option, P, and R to reset your PRAM and NVRAM
http://support.apple.com/kb/ht1379The only thing I haven’t tried is “floating” the computer. I’m not ready to heat it up to the melting point.
I need lots of help!!! any ideas? Its a MacBook Pro 15” or 17.5” about 5 years old. Its about 2 updates behind (OS: Snow Leopard)

Zane W is giving you good advice. Take it to an Apple store genius bar and have them examine it for free. You then will know what the issues are and then can make informed decisions.
Ciao.

My iphoto on my MacBook Pro will not let me import my photos from my canon t3i. It is blurred over both import all, and import selected showing that I cant choose those options. I've tried with the memory card and usb cord. Please help!

My iphoto on my MacBook Pro will not let me import my photos from my canon t3i. It is blurred over both import all, and import selected showing that I cant choose those options. I've tried with the memory card and usb cord. Please help!

What version of iPhoto?
Can you access the images with Image Capture (in your Applications Folder) ?

Because in my macbook pro will not let me open The Sims 3?

because in my macbook pro will not let me open The Sims 3?
Whenever I try to open the application icon starts jumping and then disappears

Says it works with 10.7, problems with 10.8 though.
Reinstall the program and trash the Dock icon, then make a new one and see if that works.
Then Trash it's preference file and relaunch the program to create a new one
Deleting the System Preference or other .plist file
If not then run through this, could be a sign of something bigger
..Step by Step to fix your Mac

My macbook pro will not let me stay on a certain desktop.

I created multiple desktops and was able to put my open application into different desktops. For example, I had Safari open on one desktop and powerpoint on the second. However, when I switched over from my first desktop to the second it switch back to the first automatically without me doing anything. It will not let me stay on the second desktop. Could anyone tell me what I'm doing wrong?

dana2208 wrote:
My MacBook Pro will not let me log on. How do I fix this? Can apple reset it?
Yes.
Password doesn't work?
If so, try resetting it. If the computer is having any other problem, take it to the Apple store to have it checked out.
Reset Password starting from Recovery HD
Start the computer,then press and hold down command and R keys to start into recovery partition.
When you see the Apple logo, release the keys.
Wait until OS X Utilities window shows up.
Move the mouse to the menubar at the top and click "Utilities", then select "Terminal"
from the drop down.
Terminal window will appear.
Type in resetpassword and press enter on the keyboard.
Leave the Terminal window open.
Reset Password Utility window will open with Macintosh HD selected.
Select the user account from the popup menu box.
Enter a new password.
Reenter the new password for the user.
Enter a hint.
Click the "Save" button.
Click  in the menubar and select Restart.
Log in.
If Keychain dialog box appears, select “Create New Keychain”.
Best.

My macbook pro will not shut down. It tells me that safari has cancelled shut down and to quit safari and try again, but every time I try to quit safari it won't let me. I need help...I don't know what to do.

My macbook pro will not shut down. It tells me that safari has cancelled shut down and to quit safari and try again, but every time I try to quit safari it won't let me. I need help...I don't know what to do.

Have you tried holding the power button down for several seconds? I would try the force quit as mentioned earlier first, or go to the Activity Monitor in Applications>Utilities and try force quit there.

I have created a second user on my imac (OSX 10.7.1) and applications won't stay in the dock and my preferences default after restart. Anyone else have this problem?

I have created a second user on my iMac (OSX 10.7.1) and applications won't stay in the dock and my preferences default after restart. Everything works fine with the main user. Anyone else have this problem?

Hi again, ;o)
I found this advice in another thread (here), which you might find helpful...
Unregistering the iMac from .Mac syncing and re-registering it (replacing the computer's information with the .Mac information) resolved the issue.
The .Mac sync information was Reset (i.e. recopied in it's entirety) from the MacBook (the 'good' computer) to .Mac prior to unregistering and re-registering the iMac, so a fresh copy of the sync could be loaded from .Mac to the iMac.
I hope this helps the others who have had this problem.
Regards,
Art
Yang

My MacBook pro will not start up. when I boot up, it stays on a white screen

I have a MacBook pro. My hard drive went out and I recently put a new one in it. Now when I Try to turn it on, it stays on a white screen and says loading but never does. I have Mac OS X install disc 1 and 2, and says when you put the cd in to hold down c, but every time I try, it just ejects the cd. Please help!!!Not sure of what operating system it has, or if it even has one. It had Mac OS X Snow Leopard. I am complete rookie to working on apple in general.

Reinstall Lion, Mountain Lion, or Mavericks without erasing drive
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.
Reinstall Mountain Lion or Mavericks
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

Mail won't open,won't delete, doesn't even let me turn off my macbook pro

I was using my macbook normally cheking some websites, and decided to see my mail, i clicked on it and it did open, no screen came up but at the same time i can't quit it, or move it out of the dock, i tried restarting the macbook , but it won't let me do it because the mail app is no allowing it. this is the first time i have problem with mail and i don't know why this is happening..........

My macbook air won't turn off because of skype! What do i do ? Please help!!!!!!!!!!

My macbook pro will not connect to the internet via wifi or ethernet connection

Hey guys just a few days ago randomly my 2011 macbook pro stopped connecting to the internet. My girlfriends macbook still connects fine as well as both of our iphones and my tv. Under network in system prefrences wifi is yellow and says self assigned ip, however ethernet says that it is connected with a green light but safari nor any other internet using applications will work. I even tried downloading google chrome from my girlfriends mac book and moved to my computer via flash drive but still no go on the internet. Please help me.
-thanks

Please read this whole message before doing anything.
This procedure is a diagnostic test. It won’t solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
Third-party system modifications are a common cause of usability problems. By a “system modification,” I mean software that affects the operation of other software — potentially for the worse. The following procedure will help identify which such modifications you've installed. Don’t be alarmed by the complexity of these instructions — they’re easy to carry out and won’t change anything on your Mac.
These steps are to be taken while booted in “normal” mode, not in safe mode. If you’re now running in safe mode, reboot as usual before continuing.
Below are instructions to enter some UNIX shell commands. The commands are harmless, but they must be entered exactly as given in order to work. If you have doubts about the safety of the procedure suggested here, search this site for other discussions in which it’s been followed without any report of ill effects.
Some of the commands will line-wrap or scroll in your browser, but each one is really just a single line, all of which must be selected. You can accomplish this easily by triple-clicking anywhere in the line. The whole line will highlight, and you can then either copy or drag it. The headings “Step 1” and so on are not part of the commands.
Note: If you have more than one user account, Step 2 must be taken as an administrator. Ordinarily that would be the user created automatically when you booted the system for the first time. The other steps should be taken as the user who has the problem, if different. Most personal Macs have only one user, and in that case this paragraph doesn’t apply.
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
When you launch Terminal, a text window will open with a line already in it, ending either in a dollar sign (“$”) or a percent sign (“%”). If you get the percent sign, enter “sh” and press return. You should then get a new line ending in a dollar sign.
Step 1
Triple-click the line of text below to select it:
kextstat -kl | awk '!/com\.apple/{printf "%s %s\n", $6, $7}'
Copy (command-C) the selected text to the Clipboard. Then click anywhere in the Terminal window and paste (command-V). Post the lines of output (if any) that appear below what you just entered. You can do that by copy-and-paste as well. Omit the final line ending in “$”. No typing is involved in this step.
Step 2
Repeat with this line:
sudo launchctl list | sed 1d | awk '!/0x|com\.(apple|openssh|vix)|edu\.mit|org\.(amavis|apache|cups|isc|ntp|postfix|x)/{print $3}'
This time you'll be prompted for your login password, which you do have to type. It won't be displayed when you type it. Type it carefully and then press return. You may get a one-time warning not to screw up. You don't need to post the warning. If you see a message that your username "is not in the sudoers file," then you're not logged in as an administrator.
Note: If you don’t have a login password, you’ll need to set one before taking this step. If that’s not possible, skip to the next step.
Step 3
launchctl list | sed 1d | awk '!/0x|com\.apple|edu\.mit|org\.(x|openbsd)/{print $3}'
Step 4
ls -1A /e*/mach* {,/}L*/{Ad,Compon,Ex,Fram,In,Keyb,La,Mail/Bu,P*P,Priv,Qu,Scripti,Servi,Spo,Sta}* L*/Fonts 2> /dev/null
Important: If you formerly synchronized with a MobileMe account, your me.com email address may appear in the output of the above command. If so, anonymize it before posting.
Step 5
osascript -e 'tell application "System Events" to get name of every login item' 2> /dev/null
Remember, steps 1-5 are all copy-and-paste — no typing, except your password. Also remember to post the output.
You can then quit Terminal.

After updating to 10.10.3, now my Macbook Pro will not stay logged in. I log in after restarting, and it will stay logged in for 3-5 seconds then immediately log off and go back to the login screen. Any help?

After updating to 10.10.3, now my Macbook Pro 15" (mid-2014) will not stay logged in. I log in after restarting, and it will stay logged in for 3-5 seconds then immediately log off and go back to the login screen. Any help?
By the way, I also updated my Macbook Pro 17" (mid-2009) and it seems to be running fine, though I haven't tried to restart it and log in. I'm afraid I won't be able to get this one to work either if I do.

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled in OS X 10.9 or earlier, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

Keyboard lights will not stay off no matter what I do on my MacBook Pro. Why??

I've got a MacBook Pro 2.4 GHz Core 2 Duo.
I have ALWAYS left the keyboard lights off for the 4 years I have had it.
But lately, no matter what settings I change or what I try, I cannot PREVENT the keyboard lights from coming on when I've been away from the computer for a long period of time.
Automatically illuminate keyboard in low light is NOT checked in System Prefs. I have reset the PRAM, and left the laptop off with the battery off for hours in hopes of resetting it.
Nothing will work. Almost every time I am away from my computer for hours, I come back and the keyboard lights are on. And when I tap the keyboard light brightness buttons, it just gives me the buster symbol (white circle with a line through it) on screen below the keyboard light brightness indicator for a few seconds. Somehow continuing to tap those buttons eventually makes the lights just turn off. Or holding my hands over the whole keyboard to trigger the sensor can suddenly allow me to control the on/off brightness with those buttons again. In which case I try turning the lights off completely or turning the brightness so low that it goes off.
But once again, when I wake up in the morning, I find the keyboard lights on.
Now the ONLY thing that has changed since this started happening is that I added a new User account. BUT that should asbolutely not cause this problem. I have checked to see if the System Preferences for the keyboard lights in the new user account were causing a conflict, but no, they are exactly the same as my main account.
I have not tried deleting the user account yet because I actually want it and would find it very hard to believe that was the culprit. It's just the only thing I can think of that changed shortly before this started happening.
Is there anything else I can do!?! Is there some preference file that controls the lights somewhere that could be corrupt that I need to trash?
Thank you for any help anyone can provide. This one has stumped me good.

From reading up of other forums with the same problem i have come up with two reasons why it is doing that.
first try doing a smc reset
if that does not work then it is a hardware error. Many people have had the problem and they have not been able to fix it so good luck

MacBook Pro won't boot with new hard drive, but a different MacBook Pro will

So here are the details. My friend and I both have 13-inch Mid 2010 MacBook Pro's. Same processor and specs since they were purchased at the same time, but originally had 250 GB hard drives. His hard drive failed and needed a new one. Put a 500 GB Seagate Momentus 5400.6 in his computer, and tried using a flash drive with "Install OS X Mavericks" on it to install Mavericks on his new hard drive. No matter what, it wouldn't install. I finally was able to install OS X 10.9.4 on it by connecting the new hard drive to my computer with a USB hard drive enclosure. I put the hard drive back inside his computer and it wouldn't boot (stuck on the gray screen with apple logo and a spinning wheel). I then attached to the hard drive to his computer externally with the USB enclosure, and then it booted and worked perfectly.
So, it seemed like the problem was with something inside his computer, but then I switched our drives, and that doesn't seem to be the case anymore. I put my original hard drive into his computer, and his new hard drive into my computer, and they both booted and worked perfectly, so I have no idea why his computer will not boot with the new hard drive internally.
To summarize, his computer boots with: 1) new hard drive connected externally (won't work if it's internal), and 2) my hard drive internally
but my computer boots with: 1) new hard drive connected externally AND internally, and 2) my hard drive internally.
Both hard drives have OS X 10.9.4 installed
If anyone has any idea what's causing this and how to make his computer work with the new hard drive internally that would be greatly appreciated.

So after switching the internal SATA cables from each computer, now we have
His computer, with my SATA cable:
1) Worked with every hard drive!
My computer, with his SATA cable:
1) Works with 1 TB Toshiba hard drive
2) Works with 500 GB Seagate hard drive
3) Works with my original hard drive
4) Flashing folder with question mark with his old hard drive
So it turns out you were right! Definitely had something to do with the SATA cables. But it's still strange that mine was able to boot with all the hard drives except the one that was originally in his. So it seems like it was some combination of his SATA cable and something else, since when his SATA cable was in his computer only 1 hard drive (my original) worked, and when it was in my computer, 3 hard drives worked. But at least its working, and I'm just gonna keep our SATA cables switched since that seems to work out fine

My ethernet cord won't stay in because of a slight dent on my macbook pro- will applecare cover this?

Similar Messages

Maybe you are looking for