My Firewire drive isnt mounting - can be seen in the disk utility but not mounting.

I have an older MicroNet 500GB Harddrive that has always been picky about what cables it uses. I used it not that long ago to download a mass amout of files to transfer from one computer to another and it mounted no problem. My iMac is newer bought it last year and has the 800 FW port and the Mirconet has a 400 FW and 2 800 FW ports.
I have tried multiple cables 800 to 800, 400 to 800, etc. I can see the drive in my Disk Utility and have run the first aid protocols to no avail. It refuses to mount to my computers...
Any one have any advice before I spend $200-300 to extract the data at Best Buy.
Thanks so much for any advice.

Was the external hard drive connected to a Mac or PC, when you transferred the large amount of files to it? I'm wondering if it has a corrupted directory, and needs a third-party product like DiskWarrior (which is better than Disk First Aid) to straighten it out. It's possible that the FireWire bridge board in the external case is bad (which could explain its hypersensitivity to cables used). I wouldn't pay $200-$300 for data retrieval, before exhausting less expensive options, assuming that the drive's warranty has expired. Examine the case to see how it's held together - often the cover sleeve is secured to the rear plate with small screws that can be removed. Sometimes, one screw is covered with warranty-void tape, which can be peeled back/off. If it's a plastic case, you may run into problems. Some plastic cases have hidden snap latches, that require a special tool to release without breaking them. If you can remove the case's cover, you can access the bare drive. Remove its mounting screws (either on the side or bottom of the drive) and disconnect the data and power cables. With the drive removed, you can use an adapter like this one, which will adapt the IDE or SATA interface of the drive (whichever it has) for connection to a USB 2 port on your computer. This is a generic piece of hardware - you don't need to buy one marketed for use with Macs. If the drive doesn't have a mechanical and/or electronic problem, it should mount on the desktop.

Similar Messages

Lacie Hard Drive Appears In Disk Utility But Not Desktop

Hello,
My Lacie hard drive was working fine till yesterday. It will appear in the disk utility but not on the desktop? I'm using a G4 with mac os 10.3.9. I have tried disconnecting the power and rebooting to no avail.
Any help?
Thank you.

Welcome to the forum.
Have a look at the comments on THIS THREAD. Perhaps there's something there that will help.

I am trying to upgrade my hard drive in my mac book pro using the disk utility in an attempt to clone my old hard drive. I can only get so far, just before cloning may start and receive an "error 254" and can go no further. Any idea what this error is?

I am trying to upgrad the hard drive in my mac book pro using the disk utility in an attempt to clone my old hard drive. I can only get so far throughj the process where its about to start cloing when I get a message " error 254". Any idea what that means and how do I get around this issue so I can use my new hard drive? Thanks for your input.
Vince

Connect the HDD to your MBP. Open Disk Utility>Erase and drag the HDD icon inrt the Name field. The format should be Mac OS Extended (Journaled). Click on the Erase button.
Then try the clone process again. You may use Disk Utility>Restore or a third party cloning application such as Carbon Copy Cloner or Super Duper.
Ciao.

Drive visible in Disk Utility but not Finder. Why?

I have a PowerMac G4 (mirrored drive doors) with 4 hard drives installed. 3 of the drives are set-up in a striped RAID array and the other one is my boot drive with two partitions. One one partition, I have OS X 10.3 and I can see the RAID drive fine. On the other partition, I fresh installed 10.4 but the drive does not appear on the desktop. Strangly, I can see the drive in Disk Utility and it shows me the mount point. I can even unmount and remount it but it still does not show up in the Finder. I had 10.4 server installed prior to the fresh 10.4 (not server) install and that showed it fine. I tried to see the drive in Terminal but also does not appear. Why does my drive appear in Disk Utility but not the Finder?

BDAqua wrote:
Yes, it needs the path to the drive...
:-/ Yes, I got the command in completely with the path to the drive like it states in the other post. I have no idea why it didn't recognize the command as I'm not as familiar with UNIX/Linux commands as I'd like to be.
Anyways... I found the cause of the problem (incase it happens to anyone else). Here's what happened:
The ownership on the root of my RAID volume was set to be read/write for me (under my proper username) and no access for anyone else including Admin. When I installed a fresh OS, the default user was Admin (who had no access under the previous OS). If I would've taken the time to set-up my proper account (with the same owner name as my previous OS) then it would've been visible again but since I didn't see it under the default Admin account, I stopped there to troubleshoot. Another way to make it visible was just to change the access privileges from my previous OS to be read/write for other users (or at least Admin). I would think that checking the box for "Ignore ownership on this volume" would've remedied that but for whatever reason, it didn't.
Thank you for all your help. I did learn a little even if it wasn't the direct solution. Now if only I could get Disk Utility to restore my old image without giving me crazy errors... But that's another issue altogether. ;-D

External Hard Drive showing in Disk Utility - but not desktop.

A little background:
Yesterday, I moved my shelf where I have my modem, Airport Extreme, Airport Express and an external HD connected to the extreme to be a wireless HD for all users to access. Everything worked great - no problems whatsoever.
Problem: I have reconnected everything exactly as it was and reconfigured it as it was and now the external HD is having issues. When connected to the extreme, I can see it in the airport utility, but cannot gain access to it in that way. When I connect directly to my macbook, it is recognized by the disk utility, but does not appear on the desktop.
I don't know if this may have caused the problem, but I carelessly, unplugged the power bar for which all the above mentioned hardware plugs into when moving the shelf. Now, everything works as it did, except I can't get the express to show up once it is configured (but this isn't surprising as I had to fight with it the first time I configured it - not uncommon I am told), and the HD is no longer accessible via the network, or when directly connected to my macbook.
Help! According to the utilities, the data is still on the disk, I just can't access it in any way.

From the Disk Utility, select the drive and click on the Repair Disk(not Repair Permissions) button. If the Disk Utility finds a problem it can't fix, DiskWarrior or TechTool Pro will likely succeed.
(24355)

I am using Adobe Reader X on a laptop with Windows Vista OS and Adobe Reader XI on an older laptop with Windows XP OS. While filling out the same form on each computer, I have found that I can save info on the older laptop, but not on the newer one. Thi

I am using Adobe Reader X on a laptop with Windows Vista OS and Adobe Reader XI on an older laptop with Windows XP OS. While filling out the same form on each computer, I have found that I can save info on the older laptop, but not on the newer one. This is a big problem. I must be able to save on the newer computer. Do I need to buy a new computer with a more up-to-date OS? Please help.

Adobe Reader X can only save reader-enabled forms. Adobe Reader XI can save all forms.

I'm not sure if my iPhoto library is being backed up by Time Machine. I am backing up to a LaCie external hard drive. I can open photos that are in folders but not those that are in iPhoto.

I'm not sure if my iPhoto library is being backed up by Time Machine. I am backing up to a LaCie external hard drive. I can open photos ont the hard drive that are in folders but not those that are in iPhoto.

Do a restore from Time Machine. That will tell you.

Hard drive visible in Disk Utility but not on desktop

I have an external hard drive, one of a RAID 1 mirrored pair which I have been connecting to my computer with FW800. I was having problems as was using one of them for a while, which solved them. When I hooked them both up to my computer, they showed up as two separate drives rather than one drive like before (since they were mirrored). Now the one I have been using does not appear on the desktop but I can see it in Disk Utility, but can't fix permissions with it or even verify it. I've tried connecting with USB instead of FW800 but that has no effect.

already checked, there is a problem with my computer or with the external hard drive. Now a new esata array is giving me problems so I am starting to think there is something wrong with the computer.

Hard Drive Reads in Disk Utility but not in Finder

I have a Seagate FreeAgent hard drive that is configured to NTFS. I use software to read and write to this on my macbook pro. I have plugged my hard drive into my macbook this morning and it will only read in Disk Utility, and not show up at all in Finder. I have plugged it into another macbook and have the same thing. Tried to do disk repair and it said it was repaired and operating normally, but still not opening in Finder. I also tried it on a Dell running XP and same thing, doesn't open as a folder but shows as operating normally in the XP's disk utility equivalent. I have tried finding an answer elsewhere but can't come up with anything. Besides taking it for data recovery, is there anything else I can do or try to fix without compromising the data?
Message was edited by: jazmyn96

You might get more help were you to post in something like the MacBook or OS X forum. This forum is for OS 9, an archived Apple Macintosh operating system.
That said, it sounds like your drive might be dead. When you say that you can see it in Disk Utility, you mean that it shows up in the column on the left? When you repair it, can you hear the drive spinning up?
Can you try making an image of the drive to see what happens?

Can't restore backup with disk utility: "Operaton not permitted"

OK, my imac 2.8 alum hard drive broke down. i backed it up before it failed, and have been using the firewire drive i backed up to as the startup with my second mac (a mini) for the last week.
Now trying to restore the backup back to the imac with the new drive. the backup is 210gb, the new partition is 250gb.
But the disk utility has been giving me this error:
2009-04-08 01:09:38 -0700: Copying
2009-04-08 01:28:13 -0700: could not copy /Volumes/Blank Slate/bin/.BC.7setUX; Operation not permitted
2009-04-08 01:28:13 -0700: Bom copy exited with error 1
2009-04-08 01:28:13 -0700:
2009-04-08 01:28:13 -0700: Could not restore - Operation not permitted
2009-04-08 01:28:14 -0700: Could not restore - Operation not permitted
2009-04-08 01:28:15 -0700:
Any thoughts?

It means that Disk Utility is choking on the hidden file .BC.7setUX buried in /bin. That file doesn't exist on my machine. Launch the Terminal app, type in this command, hit the return key, and quit the Terminal app;
*rm /bin/.BC.7setUX*
Now, try restoring again.

External hard drive suddenly became "unreadable" and the disk utility offers not repair options. The drive is visible in disk utility but may not be mounted... any suggestions?

I have a WD My Passport 070A Media 2.0 TB external hard drive that has suddenly become unreadable on my laptop (MacBook Pro circa 2006 with 10.4.11) and I have tried on a MacBook Pro 2011 running 10.6.8 with the same results. I had tried opening disk utility to repair the drive, but on both machines the drive is visible in the left column, with no indentation below the drive. When I select the drive in the first aid portion the only options highlighted are info and eject... I was wondering if anyone had any suggestions to repair the drive. I am currently in Belize and am not home for 3 weeks yet. I'm hoping for a fix while I am down here, otherwise I may have to wait... I appreciate any assistance!
-Christina

Hi Christina,
It's quite possible the AC PSU has given out, if It's only Bus powered as it appears, that's the worst idea ever & asking for eventual problems.
What Format is it?
Did you install any WD SW?
Your best bet is DiskWarrio...
http://www.alsoft.com/DiskWarrior/
But others that may work…
Drive Genius…
http://www.prosofteng.com/products/drive_genius.php
TechTool Pro…
http://www.micromat.com/index.php?option=com_content&task=view&id=31&Itemid=83

Old internal Macbook Pro hard drive (now in enclosure) is partially read in Disc Utility, but not in Finder or Diskwarrior - I need those files!

Recently I totalled my old Macbook Pro with a glass of red wine. Fortunately, whilst the guys at the mac store said that almost every component was totally screwed - the HD seemed okay. On their advice I purchased an enclosure, carefully removed and installed the old HD, booted up my new Macbook Pro...
Upon plugging in the drive (via USB) I receive the following message - "The disk you inserted was not readable by this computer" and the options "Initialize, Ignore, Eject". The drive is, obviously, not read by Finder but upon clicking initialize I get this from Disk Utility.
All options are 'greyed out' - there doesn't seem to be anything that I can do to retrieve the information at this juncture - so I downloaded Diskwarrior but to no avail. It doesn't seem to recognise the existance of the drive at all.
A few things I will try today: Powering the enclosure externally (it's currently running off the USB), Purchasing a different enclosure.
Another issue is that I'm not made of money and I've already forked out £100 for enclosure/Diskwarrior. I am not madly keen on blowing the same amount again to get an engineer to come and shrug at it. Or worse, pay £1 per GB for data retrieval!
Does anyone have any ideas/advice about this at all?

File recovery software: Try using an application such as Data Rescue 3 - http://www.prosofteng.com/products/data_rescue.php or FileSalvage - http://subrosasoft.com, or one of the ones listed in the link below. Some have free trial versions that let you see if the software will help before you decide to buy. You will also need a second hard drive equal to or larger in size than your first drive as a destination drive for recovered files.
http://data-recovery-software-review.toptenreviews.com/mac-recovery-software

Hallo ,why is it that when I delete a photo ,which is backed up by time machine and western digital external hard drive , that I am able to restore the photo okay but not the titles and descriptions . I have a Macbook 4.1, mac osx 10.5.8 . Iphoto 7.1.5 ,

QUESTION.
Hallo , my question is ;whenever I delete a photo and restore it through Time machine and Western digital external hard drive , I am able to restore the photo but not the titles and descriptions . Western Digital inform me that it isn't their external hard drive problem and suggest that it is an Apple software problem ?
I am using a Macbook 4.1 , with Mac OSX 10.5.8 . I photo 7.1.5 , last modifie4d 01/05/2010 -universal . Should I be upgrading Iphoto ?
I hope that someone is able to help in this matter , as i have to restore 12000 photos !
Thanking you in anticipation.
Alan from Wigton

Hallo Kieth ,
I am not quite ready to restore the full iphoto library , as I have days of work re - imputting titles,descriptions and enhancement . I hope that your suggestion works , as I use my Macbook basically to work with digital photography. Through time , I will need to delete my library to recover more disc space and I would hate to have to spend more time re - imputting titles and descriptions all over again .
Thanks for your interest and advice.
regards - Alan

How do I increase the point size and change the font for the windows and boxes on Maverick such as the tiny print on the email inbox list of messages. Can increase size on the actual message but not on the list of messages.

How do I increase the point size in the dialog boxes and especially on the list of messages on email? I can increase the point size and font of actual messages content but not the LIST of emails in my inbox. They are too small for me to read.

This discussion is for computer built before 2006.
You could use a different mail app. Consider thunderbird.
It can be hard to find with community ( forum ) to post to. Here is an easy and complete list:
https://discussions.apple.com/community
I'll ask the host to move this post to M.
Robert

I just updated to Mavericks and now I can't get my toshiba external HD to show up. It appears in Disk Utility but not in my finder. In Disk Utility it is grayed out and will not allow me to mount. Ive verified and repaired it. Nothing!

I cant take it anymore. Pleae someone help me. I cannot erase my HD becasue it has all of my pics for my kids and all of my movies school work. I need this fixed please

Hi Liz,
Sorry to hear you are having a similar problem. Last night I went to the tool bar at the top of iphoto, clicked on "File", then clicked "Browse Backups" in the drop down menu.    I have an external hard drive that is set up to Time Machine.   The Browse Backups opened the iphoto pages in the Time Machine. I selected a date one day ahead of the day I performed the now infamous update, and it showed my iphoto library as it had existed that day.   I then clicked "Restore Library" at the bottom right corner of the Time Machine screen.   Roughly 2 hours later my iphoto was back to normal.   When I opened iphoto there was a message saying I need to upgrade my program to be compatible with the new version of iphoto(version 9.2.1). I clicked "Upgrade" and within seconds it had done whatever upgrading it needed to do.
The only glitch in the restoration was that it restored the library as it appeared last week, so I no longer had photos I had imported this past weekend.   I simply went back to the Browse Backups in the drop down menu, when Time Machine opened I selected the page showing my pictures from this weekend and again said to Restore Library.   Roughly 45 minutes later the library was restored including the most recent photos.
I am now a happy camper.
I don't know if any of this will be of help to you because your email says you are having trouble with photos imported after the upgrade was performed.   Have you had any pop up notices when you first open iphoto, that tell you you need an upgrade to be compatible with the new iphoto?     If so have you clicked "upgrade"?
Good luck Liz, if you have Time Machine running as a back up to your library, maybe you wil be able to get help there, by following my instructions above.   Otherwise,   good luck with your investigations.   I'd be interested in hearing how you make out.
Karen

My Firewire drive isnt mounting - can be seen in the disk utility but not mounting.

Similar Messages

Maybe you are looking for