My iMacG5 shutsdown from the Gray screen with Apple logo after the fans run

I hope someone who might read this can help me...
Tonight my iMac G5 screen froze and prompted me to do a forced shut down. Upon restarting the computer it would not allow me to log in. After the start up chime sound and the gray screen with the Apple logo with spinning wheel happens, it shifted to a blue screen and stayed stuck that way not going further to my log in profile.
After a few forced shutdowns, the gray screen with the Apple logo did not shift to the blue screen, instead, as soon as I hear the computers fans blow, the computer now automatically shuts itself off.
Following online posts, I tried both the command option PR function and also at start up I tried the fscyk -fyk (something like that) but both failed to fix the issues.
I am worried that I might have to shell out fees just to get Apple advice that might not guarantee a fix.
Help!
Thank you.
Message was edited by: ao71

Take a look at these 2 articles: Startup issues
http://support.apple.com/kb/TS1417
Gray screen at startup
http://support.apple.com/kb/TS2570

Similar Messages

MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!

MacBook will not start. I have restarted with original CD. I have used Utilities and "no problem" with hard drive. I have reset PRAM. I have tried safe boot. Nothing is work. Gray screen with Apple logo and rotating wheel. Thanks for any suggestions!

Snow Leopard is a Mac OS X version. You say that it's the version you have in your Mac (10.6.8). Do a back up of your files, format the hard drive (using Disk Utility) and reinstall again

IMac G5 boots to gray screen with Apple logo only

iMac G5 boots to gray screen with apple logo only.
What I've tried:
Won't boot to safe mode.
Reset PRAM several times.
Won't boot to install disk with "C" depressed at startup.
Will boot to screen showing HD and arrow buttons when "alt" depressed at startup. But clicking HD icon and proceed arrow just goes back to the gray screen with apple logo. Note the HD icon has a blue "x" symbol.
With install disc in, will boot with "alt" depressed at startup to three icons, HD, install disc, and apple hardware test. Both HD and install disc icons have the blue "x" symbol and won't run. BUT the apple hardware test icon doesn't have a blue "x" and runs. Extended test says all hardware OK.
Finally, startup in single user mode with "apple-s" depressed goes to a non-gui white text (UNIX core?) which gives blocks of repetitive text starting "unresolved kernal trap (cpu0)...(lots of date)...latest crash.....backtrace:" My rough guide to the Mac gives me text to enter at that point but I can't input to the screen.
That's where I'm stuck.

You're encountering a kernel panic.
[I got a black screen telling me I had to reboot in many languages, what was it?|http://www.dslreports.com/faq/4970] Also has detailed description of what happens during a KP.
[Apple docs: What's a kernel panic? (Mac OS X)|http://docs.info.apple.com/article.html?artnum=106227]
[Topic : kmosx: Kernel Panics? Don't panic too !|http://discussions.apple.com/thread.jspa?threadID=121923]
[X-Lab: Resolving Kernel Panics|http://www.thexlab.com/faqs/kernelpanics.html]
[Tutorial: Avoiding and eliminating Kernel panics|http://www.macfixit.com/article.php?story=20060911080447777]
[Tutorial: An introduction to reading Mac OS X crash reports|http://www.macfixit.com/article.php?story=20060309075929717]
[12-Step Program to Isolate Freezes and/or Kernel Panics|http://macosg.com/group/viewtopic.php?t=800]
[Texas Mac Man's post on kernel panics|http://discussions.apple.com/thread.jspa?threadID=1723768&tstart=0]
These are often attributed to hardware problems though they can also be due to corruption of software. Since you're also encountering it with your DVD I'd tend more towards the former. Your computer seems to be passing the early stage POST tests for RAM. Apple Hardware Test also seems to be passing but [X-Lab: The Apple Hardware Test|http://www.thexlab.com/faqs/aht.html] document recommends using this in loop mode to test for intermittent problems.
Sometimes the crash logs (all the error messages you are seeing) contain information about the problem, but there's an art to reading those.

Electric went out my computer is just showing gray screen with apple logo and wont start up

my mac mini is just showing gray screen with apple logo on it i cant get into it

Mac OS X: Gray screen appears during startup

Grey screen with apple logo after new HDD install

I have a mid 2010 iMac A1312, this was given to me recently with the knowledge of its bad HDD, so I bought a new HDD. I followed step by step instructions on how to replace a Hard drive and I did. I switched the computer on and inserted my Snow Leopard 10.6.3 install disk and clicked the icon. It is now at a light grey screen with a dark Apple logo. I have waited about ten minutes and restarted the machine. Ive tried all variances of startup holding down c, option, command r and so forth. Currently I am going to give it a good long wait of 20 minutes or so and see if I was just being impatient and not allowing the install software chance to start up. But in the mean time... any suggestions? I have read I need the original disks that came with the computer from factory to get a new HDD going. Is this true? thank you for your time!

it has now been 30 minutes and no change. I still have the grey screen with apple logo. please help

After wiping phone to sell phone will not turn on, it stays on a black screen with apple logo.after forced reboot, it goes to same exact screen. any ideas?

my brothers girlfriend gave me her old iPhone. the last thing she did to the working phone was to wipe it to erase all her private info. however instad of booting up like normal, all i get is a black screen with apple logo. ive forced a reboot and it goes to same screen. sometimes it will turn off and reboot by itself, and occasionally it wil give a low battery icon, and it will show it charging for a few min then go back to black screen with Appple logo. any ideas anyone?

Try to charge it for about 10min using th adapter, then connect to your computer in recovery mode, explained here: iOS: Unable to restore

I have a MacBook Pro 2008 with 17 inch screen. Experiencing a lock up when turning on power to boot up. While booting up it goes to gray screen with Apple logo and disc spinning icon running and doesn't go to my desktop. Any solutions to the problem?

I have an early 2009 17 inch MacBook Pro that just went on the fritz. When turning on the power it will go into boot up mode to the gray screen with the apple logo, then the disc icon will be running and will continue running, not allowing to proceed to my desk top screen. It's pretty much locked up at this point where I have to do a forced shut down by holding down the power button. I've tried everything that I know of such as taking battery out and pressing power button for 5 seconds and then reinstalling battery. I've cleaned inside of computer with compressed air duster in can as well as other key commands for resets. I've read that this is a common problem with the earlier MacBook Pros. Is this a problem that I can fix or does it have to be taken in for service? Any solutions to the problem would be greatly appreciated. Thanks!

This could be a software/state problem or a hardware problem. Here are steps to resolve the former.
http://support.apple.com/kb/TS2570
https://discussions.apple.com/docs/DOC-5282

Boots to gray screen with apple logo and no spinning wheel

For some reason, all my programs that were open (Safari, iTunes) were not responding and the spinning color wheel appeared. I simply pressed down on my power button to reset my laptop.
Soon after my laptop booted to a gray screen with the apple logo. There was no spinning wheel. I did here the chime noise and my screen remains like this as we speak.
I tried to use my install CD but nothing changes on my screen.
Please advise.

Uh-oh, that's not good. What exactly did you do when you put your install CD in? Did you make sure to hold down the "C" key on the keyboard to startup from it?
From there, you can try Disk Utility to see if the hard drive needs to be repaired.
MAKE SURE YOU DON'T USE TECHTOOL DELUXE that came with AppleCare if you have it. There is a glitch--I learned the hard way... had a kernel panic on my PowerMac G4 last week and the drive went from bad to worse... it's here on the Apple forums somewhere--that causes the directory on the affected volume to go unreadable.
Using DiskWarrior won't help either.
If Apple's Disk Utility can't help you, I recommend backing up your data (if you can see it with another Mac under Target Disk Mode--hold down the "T" key on the keyboard and startup while connected to another Mac via FireWire--take your files off that way) and then using Data Rescue II.
It saved my behind. TechTool Deluxe ruined my drive, DiskWarrior couldn't help, but Data Rescue II did. Best $99 I ever spent! It's at the Apple Store, or available online.
That is, if it comes to all of this. Try restarting from your installation CD (restore disc) if you haven't done so already, and use Disk Utility to see what it reports. If it says repair, do so. Apple's Disk Utility won't ruin it... only TechTool Deluxe (from the AppleCare package).

Gray screen with Apple logo and spinning gear appears during startup

I followed the steps outlined in order in Apple Support by disconnecting all peripheral devices, performing a safe boot, and resetting the NVRAM / PRAM. Nothing changed - the gray screen still appeared when restarting the computer. Next I tried bringing up the Mac OS X Install disc using Disk Utility. I was able to get into Disk Utility but it would not allow me to click "Repair Disk" for the hard drive. I could only select "Verify Disk". So I did that then and the results in red were as follows:
-Invalid node structure
-The volume Macintosh HD needs to be repaiired.
Error: Filesystem verify or repair failed.
So this is where I'm at, unsure as exactly how to proceed from here. Any suggestions or advice would be greatly appreciated! Thank you.

Well I tried entering in (after the "umount/dev/") disk0s1, disk0, disk1, disk2 etc. all to no avail. So I'm just recopying below exactly what shows up on screen in the Terminal once I enter "df" so that maybe you can better detect that way what my volume should be. Thanks David!
-bash-3.2# df
Filesystem 512-blocks Used Available Capacity Mounted on
/dev/disk1s3 15513624 15414064 0 100% /
devfs 217 217 0 100% /dev
fdesc 2 2 0 100% /dev
/dev/disk2 934 12 876 2% /Volumes
/dev/disk3 934 124 764 14% /private/var/tmp
/dev/disk4 190 22 160 13% /private/var/run
/dev/disk5 190 4 178 3% /Library/Preferences

HT1338 White Mac book will not start up just shows gray screen with apple logo

White Mac book will not boot up gray screen only

There are some recovery steps for this condition outlined in the below article.
Mac OS X: Gray screen appears during startup

Stuck on grey screen with apple logo after failed iTunes update

I tried to install an update for iTunes 9.2 on my MacBook. During installation a box appeared telling me the update had failed. I clicked the 'Restart' button. Now it won't go past the grey screen with the apple logo and the rotating wheel; it just loads indefinitely. I have a very important document saved on the Mac which I've added to without backing it up. I'm worried that I will lose (or have already lost) a great deal of writing. Is there a way to get my computer running again without damaging my files? Because this computer was a gift, I don't have the software installation CDs that came with it (or Disk Utility). I'm also not very familiar with computers in general, so if you explain your solutions in a really basic way, I'd appreciate it. Any kind of advice would be extremely welcomed...

This one?
http://docs.info.apple.com/article.html?artnum=106214
Resolve startup issues and perform disk maintenance with Disk Utility and fsck
* Last Modified: June 25, 2009
* Article: TS1417
* Old Article: 106214
[Email this article]
[Print this page]
Symptoms
If your computer won't start up normally, you may need to use a disk repair utility to fix the issue. Mac OS X includes two utilities for this—Disk Utility and fsck (a command-line utility). You can also use these even when your computer starts just fine but you want to check the disk for possible file system issues. For Mac OS X 10.4.3 or later, check out "About live verification in Mac OS X 10.4.3 or later," below.
Important: If you're using Mac OS X 10.4 or later, you should use Disk Utility instead of fsck, whenever possible.
In some situations, file system errors may prevent your computer from starting up. This can occur after an improper shutdown, forced restart, or power interruption. If your computer shows any of the following symptoms on startup, use a disk repair utility:
* Your computer partially starts but then displays a command line in a text-only environment. You may see the message, "file system dirty, run fsck." Below it, you'll see what's called a command-line prompt, indicated by a number sign (#), that allows you to type a command. If you see this, you'll need to run fsck from the command line (see "Use fsck if necessary," below).
* Your computer starts but either it won't reach the login screen, or it may reach the login screen but not load the Desktop after you log in. However, you can start up in single-user mode.
If your computer exhibits either of the above issues, here are some things to try to get your computer back to starting up properly again. If you can't find the system discs that came with your computer, see "Use fsck," below.
Products Affected
Mac OS X 10.4, Mac OS X 10.3, Mac OS X 10.2, Mac OS X 10.1
Resolution
Try a Safe Boot
If you're using Mac OS X 10.2 or later, you can start up your computer in Safe Mode, which includes an automatic disk check and repair. If you're using Mac OS X 10.1.5 or earlier, skip to the next section. A Safe Boot, which starts up your computer into Safe Mode, may allow you to start up your computer successfully using a reduced version of the system software. To do this, follow these steps:
1. Start up in Safe Mode.
2. After the system has fully started up, restart your computer again normally.
If the computer successfully restarts, you do not need to do any more troubleshooting. If the issue persists, try Disk Utility.
Try Disk Utility
1. Start from your Mac OS X Install disc: Insert the installation disc, then restart the computer while holding the C key.
2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.
3. Click the First Aid tab.
4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
5. Select your Mac OS X volume.
6. Click Repair. Disk Utility checks and repairs the disk.
Tip: Always start up your computer from an Install or Restore disc when using Disk Utility to verify or repair your startup volume. Otherwise, you might see some disk error messages.
Use fsck if necessary
fsck is a command-line utility that may be able to verify and repair a disk. If you can successfully start up in Safe Mode or use Disk Utility while started up from a disc, you don't need to use fsck. Here are some situations in which fsck may be necessary.
* Your Mac OS X disc isn't available.
* Your optical drive isn't available.
* You can't start with a Safe Boot by holding the Shift key during start up.
Tip: If you use a Mac OS X Extended (Journaled) formatted volume, such as with Mac OS X 10.3 or later, you probably won't need to use fsck. If you do use it for any reason, please be aware that benign error messages can appear.
If you're not sure how your volume is formatted and you can't start up from your Mac OS X volume to find out, type the following command in a command-line interface and then press Return: diskutil info /
If you see "File System: Journaled HFS+" returned, you have a Journaled volume.
To use fsck, you must run it from the command line. Unlike using your mouse pointer to open an application to do something, you'll need to type a text command at the prompt (#) to tell fsck what to do. The Terminal application (/Applications/Utilities) and single-user mode are two examples of command-line interfaces in which you can type such commands. To use fsck:
1. Start up your computer in single-user mode to reach the command line.
Note: If necessary, perform a forced restart as described in the Emergency Troubleshooting Handbook that came with your computer. On desktop computers, you can do this by pressing the reset/interrupt button (if there is one) or holding down the power button for several seconds. On portable computers, simultaneously press the Command-Control-power keys. If your portable computer doesn't restart with this method, you may need to reset the Power Manager.
2. At the command-line prompt type:
/sbin/fsck -fy
3. Press Return. fsck will go through five "phases" and then return information about your disk's use and fragmentation. Once it finishes, it'll display this message if no issue is found:
** The volume (nameofvolume) appears to be OK
If fsck found issues and has altered, repaired, or fixed anything, it will display this message:
*** FILE SYSTEM WAS MODIFIED ***
Important: If this message appears, repeat the fsck command you typed in step 2 until fsck tells you that your volume appears to be OK (first-pass repairs may uncover additional issues, so this is a normal thing to do).
4. When fsck reports that your volume is OK, type reboot at the prompt and then press Return.
Your computer should start up normally and allow you to log in.
Additional Information
About live verification in Mac OS X 10.4.3 or later
In Mac OS X 10.4.3 or later, you can verify your Mac OS X volume while started from it. This is known as live verification, and can be used in three different ways.
Option 1: Verify your disk using Disk Utility while started from the startup disk. To find out how to do this, see this article. Please note that live verification does not involve any disk repair, so if verification finds something that should be repaired, start up from your Mac OS X Install disc and use Disk Utility as described above in "Try Disk Utility."
Option 2 (advanced): Use the command line and the command-line utility, diskutil.
1. Start up your computer and log in as an administrator.
2. Open Terminal (/Applications/Utilities).
3. At the prompt, type the following command and then press Return:
diskutil verify /
Note: Don't use this method to check non-startup volumes.
You should see messages such as the following during the disk check:
Could not unmount disk for verification, attempting live verify
Started verify/repair on volume disk0s3 Macintosh HD
Checking HFS Plus volume.
Checking Extents Overflow file.
Checking Catalog file.
Checking multi-linked files.
Checking Catalog hierarchy.
Checking Extended Attributes file.
Checking volume bitmap.
Checking volume information.
The volume Macintosh HD appears to be OK.
Mounting Disk
Verify/repair finished on volume disk0s3 Macintosh HD
Option 3 (advanced): Use the command line and the fsck_hfs -l command.
1. Start up your computer and log in as an administrator.
2. Open Terminal (/Applications/Utilities).
3. At the prompt, type the following command and then press Return to determine your filesytem ID:
df -hl
4. Look for some lines of text that look like this:
Filesystem Size Used Avail Capacity Mounted on
/dev/disk0s3 37G 20G 17G 55% /
/dev/disk0s5 37G 37G 641M 98% /Volumes/Storage
5. Make a note of the first "disk" name that appears after /dev/, such as "disk0s3." This is your filesystem ID for your startup volume.
6. At the prompt, type the following command and then press Return:
df -hl
7. Then type the following command, where "disk0s3" is your filesystem ID you noted in step 4, then press Return:
sudo fsck_hfs -l /dev/disk0s3
8. When prompted, enter your admin password, then press Return to begin the verification.
9. You should see messages like these during the disk check:
** /dev/rdisk0s3 (NO WRITE)
** Root file system
** Checking HFS Plus volume.
** Checking Extents Overflow file.
** Checking Catalog file.
** Checking multi-linked files.
** Checking Catalog hierarchy.
** Checking Extended Attributes file.
** Checking volume bitmap.
** Checking volume information.
** The volume Macintosh HD appears to be OK.
Advanced information
If you're interested in UNIX-style command-line syntax, here's a look at how a couple of flags used above can influence fsck:
* The -y flag: Tells fsck that you want to answer "yes" to all questions about fixing, repairing, or salvaging information. This is the optimal approach, as answering "no" to any question causes fsck to stop. You cannot determine that all necessary repairs have been made until fsck completes and gives its final report.
* The -f flag: Forces fsck to check "clean" filesystems when preening.
See also
* Handling "overlapped extent allocation" errors reported by Disk Utility or fsck
* Disk Utility reports "Underlying task reported failure" when repairing a volume

White Screen with apple logo after screen replacement Iphone 5

So my friend gave me her phone because she dropped it and had someone repair it but it only worked for a second before the screen went to the apple logo that is black and has a white background. So the guy put the screen back on and gave it back to her. Anyways she gave me the phone and i was wondering what the problem is. Did he fry the mother board.
Here is a detailed description: the phone turns on and off with a white screen and black apple logo then it goes black. When u press home and the sleep button then it goes black with purple on the bottom and two vertical lines. When i plug it into my computer it will sometimes go completely blue. What happened and is it repairable cause i want to ditch my iphone 4s and use her iphone 5.
The person who gave me the phone is a girl to clarify the she and the person who tried to repair it was a guy. He repaired 2 phones so far so i think he is somewhat reliable
BTW the computer wont recognize the phone and the old screen is back on.

Take the iPhone back to the 'someone' who repaired it. Apple will not touch that iPhone
now that a 3rd party has opened it.

Start up stuck on gray screen with apple logo on startup

I have tried booting in Safe Mode by pressing shift, but after I see the bar load it goes right back to the apple with the spinning wheel.
I tried refreshing the pram (command option p r) and that didn't do anything.
I tried shift command v and the last line that it got stuck on was BootCache Control: could not unlink bootcache playlist/var/db/bootcache.playlist 22 invalid argument. Then it just stopped there.
Also, I am running Mountain Lion on Mid-2010 Macbook Pro.
Any suggestions?

I took it to the Apple store by me and they said it wouldn't read the hard drive. I took it to a data recovery place and they said they could easily get the data off my hard drive - for $350 bucks. I did more research and found that I needed a new hard drive cable. This is what I got for the Macbook Pro - http://www.amazon.com/gp/product/B009JGNKSA/ref=oh_details_o05_s00_i00?ie=UTF8&p sc=1 but I am sure you will need a different version of the part for the Air. Look up the part by the date of your Macbook Air (something like Late 2011, Mid 2012, etc.).
It was easy to take out and re-install myself. Good luck.

IPod touch is frozen at black screen with apple logo after updating to OS 6

I was updating to new software, it told me to plug into itunes. clicked restore ipod and then the problems started. my computer doesnt even recognize it now. I've tried restarting with no luck. Done many steps recommended by Apple and still cant get it to work.

Try:
- iOS: Not responding or does not turn on
- If not successful and you can't fully turn the iPod fully off, let the battery fully drain. After charging for an least an hour try the above again.
- If still not successful that indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
The above may be repetitive but you did not say what you tried.

I have an iMac from 2008. When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen. Now just back and forth blue to light blur

I have an iMac from 2008. When I start I get gray screen with apple and turning gear. Next blue screen. Then light blue screen with turning gear. Back to blue screen. Now just back and forth blue to light blur

Reinstall OS X:
Reinstall OS X without erasing the drive
Do the following:
1. Repair the Hard Drive and Permissions
Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
2. Reinstall Snow Leopard
If the drive is OK then quit DU and return to the installer. Proceed with reinstalling OS X. Note that the Snow Leopard installer will not erase your drive or disturb your files. After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.
Reinstalling Lion Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall Lion: Select Reinstall Lion and click on the Continue button.
Note: You can also re-download the Lion installer by opening the App Store application. Hold down the OPTION key and click on the Purchases icon in the toolbar. You should now see an active Install button to the right of your Lion purchase entry. There are situations in which this will not work. For example, if you are already booted into the Lion you originally purchased with your Apple ID or if an instance of the Lion installer is located anywhere on your computer.

My iMacG5 shutsdown from the Gray screen with Apple logo after the fans run

Similar Messages

Maybe you are looking for