My question has to do with analog input and triggering? Does anyone have any suggestions on how i can improve the attached vi so it can trigger on a 50kHz ten cycles pulse after the pulse has been sent out on the output?
Could you just look at this vi and tell me if i am doing anything wrong? I get errors that are different each time I change something. here are the inputs I am using
Output Side:
amplitude = 1
freuency = 50kHz
Sampling Frequency = 1MHz
3 of Samples = 200
Input Side:
Input Buffer 4000
trigger type = analog
pretrigger = 5
edge or slope = rising
scan rate = 500kHz
# of scans = 2000
Conditional Retrieval
mode = on
slope = rising
skip count = 0
level = .1
offset = 0
hysteresis = 0
So what we want to do is capture the ten
cycles of the 50k output pulse on the input and need to store that so we can plot it later, do you have any suggestions. we are using the PCI-MIO- 16E board.
Thanks,
Jarrod
Attachments:
InputOutput2.vi 88 KB
1) Toss the sequence frames (no flames please).
2) Set you read and have it ready to trigger before oing the output.
3) After the output, go back and read the data that is waiting for you.
4) If you have errors tell us what they are and under what conditions they occured.
End of Ben's suggestions for now.
Ben
Ben Rayner
I am currently active on.. MainStream Preppers
Rayner's Ridge is under construction
Similar Messages
-
My video app that is preloaded on the IPAD will not open. all I can see is a blank screen. Does anyone have any suggestions on how I can fix it?
The "The connection was reset" error message can be caused by a bug fix for the BEAST (Browser Exploit Against SSL/TLS) attack that the server doesn't handle.
*[[/questions/918127]]
*[[/questions/918028]] -
Hi all.
My headphones are new form apple as they came with the phone. They have been good for the few times i have used them but out of the blue after about a weeks use they have stopped allowing me to skip forwrd or backwards???????? I am still able to pause and use my mic for Siri so im a little bit confused as to what the problem can be.. Is there anyone out there who knows what the problem might be or how to fix it??
Thanks.Go to the settings in your Jeep, "forget" the iPhone. And on the iPhone "forget" the jeep. Then put the Jeep in Pairing Mode and tap Settings/BlueTooth on the phone and pair them anew (which sounds less confusing than "repair them").
-
My iPad2 has repeatedly refused to update to iOS7, whether connected to a PC or not. The error message indicates an unknown error has occurred, with error code 6. Does anyone have any idea what the problem might be and how to solve it? Many thanks.
Hi
I followed this guy's instructions and it worked:
http://evsiphone.blogspot.com/2009/05/iphone-iphone-could-not-be-restored.html
I did disable the security (AVG and Zone Alarm) when I tried on my own PC. My wife's laptop which eventually got it working also uses AVG and Zone Alarm but on an XP O/S whereas my PC is Vista - maybe this is why.
Cheers for you help.
Andy
Message was edited by: bigbadandy -
Photos either do not arrive at all or arrive as an unrecognized file type, or sometimes go straight through. Apple support has been unable to resolve. Does anyone have any suggestions??? I am experiencing this on all my devices -- MacBookAir, iMac, both running most current version of Lion; iPad v1.0; and iPhone 4S
Turnmerv wrote:
Photos either do not arrive at all or arrive as an unrecognized file type, or sometimes go straight through. Apple support has been unable to resolve. Does anyone have any suggestions??? I am experiencing this on all my devices -- MacBookAir, iMac, both running most current version of Lion; iPad v1.0; and iPhone 4S
If you can not send from any of these devices then it has to be your e-mail service - the e-mail clients for OS X and for IOS 5 are totally different - the only common thread between all of these devices is your e-mail service
LN -
I've been working on our church website and all of a sudden this week, my computer will not connect to the site. I keep getting a message saying that the the connection to the server was reset while the page was loading. Does anyone have any ideas of how I can fix this?
The "The connection was reset" error message can be caused by a bug fix for the BEAST (Browser Exploit Against SSL/TLS) attack that the server doesn't handle.
*[[/questions/918127]]
*[[/questions/918028]] -
Since updating my iphone 4S it has started showing no service, i have gone into the apple store and they couldn't fix it does anyone have any suggestions?
They offered to value my iPhone and then put that money towards buying me out of my contract however I don't want to have to spend more money when my contract ends on august anyway.
-
I have an early 2008 Mac Pro, 8 gb ram with a Dell 27” display and a 42” LG TV. I am thinking about upgrading the stock ATI Radeon 2600 graphics card for better resolution, preferring 2 dvi outputs or 1 dvi and 1 vga vs 1 dvi and a mini. I don't do a lot of Final Cut Pro, gaming, etc. I am interested in best value for the graphics card.
Does anyone have any suggestions on the best graphics card for these larger displays for the best value?
Thanks,
KevinI recommend you install nothing older than the Apple-firware 5770, about US$250.
RE: Mac Pro Replacement Graphics cards
1) Apple brand cards,
2) "sold in the Apple store" cards, and
3) "Mac Edition" cards ...
... show all the screens, including Boot up screens, Safe Mode, Installer, Recovery, debug screens, and Alt/Option boot screens. At this writing, these choices include:
1) Apple brand cards:
• Apple-firmware 5770, about US$250** works near full speed in every model Mac Pro, Drivers in 10.6.5
• Apple-firmware 5870, about US$450
2) "sold in the Apple store" cards
• NVIDIA Quadro 4000, about US$1200
• NVIDIA Quadro 5000, about US$2500
3) "Mac Edition" cards -- REQUIRE 10.8.3 or later:
• SAPPHIRE HD 7950 3GB GDDR5 MAC Edition, about US$480** Vendor recommends Mac Pro 4,1
• EVGA GTX 680 Mac Edition, about US$600
The cards above require no more than the provided two 6-pin aux power connectors provided in the Mac Pro through 2012 model. Aux cables may not be provided for third-party cards, but are readily available.
If you are Meet ALL of these:
• running 10.8.3 or later AND
• don't care about "no boot screens" etc AND
• can re-wire or otherwise "work out" the power cabling, THEN:
You can use many more cards, even most "PC-only cards" -
After moving to iCloud I can only get my email through the cloud, no new emails are making it to my home computer and .mac account. Does anyone have any advice on how to fix this issue?
Welcome to the Apple Community.
Which OS are you using. -
tried installing Icloud calendar on windows 8.1 and get the message "Calendar has stopped responding". does anyone have any suggestions?
Hey there Alex,
Welcome to Apple Support Communities.
It sounds like you’re running into an issue installing iCloud Control Panel on your PC, you’re seeing an alert message related to an iCloud server not responding. Take a look at the article linked below and try running through the troubleshooting steps it provides.
iCloud: iCloud Control Panel setup cannot be started - Apple Support
So long,
-Jason -
Why can't I connect to my work e-mail (Outlook 2003) using either the regular e-mail account set-up or Mail 2003? Does anyone have any suggestions?
I have yet to find an email server that does not work with Mail.app. Your solution will be to configure its ports and send/receive protocol according to the email server's requirements.
Try the Zimbra support forums. I found this excerpt from a relevant post:
http://www.zimbra.com/forums/users/46221-mac-mail-app-dont-work-outside-company. html
in which the following ports were suggested
ports 25, 465, and/or 487 to send mail.
port 143/993 to retrieve mail over IMAP -
I have been noticing videos on hulu, youtube and even itunes have been downloading slow and pausing in the middle of watching them. Does anyone have any suggestions on what I should do? Someone told me its my media player, but I am not very good at computers and don't want to download the wrong thing.
I have been noticing videos on hulu, youtube and even itunes have been downloading slow and pausing in the middle of watching them. Does anyone have any suggestions on what I should do? Someone told me its my media player, but I am not very good at computers and don't want to download the wrong thing.
-
I am trying to connect my Macbook pro 2010 to my Samsung HDTV using a mini display port to hdtv cable. Trying to play a slide show in IPhoto but I only get sound with no picture. Does anyone have any suggestions?
I keep saying this over and over, in the hope that people who do a search will find it. Apple cannot possibly test for or be reponsible for the bazillion combinations of adapter, cables, and TV's out there. The only monitors that are 100% guaranteed to work with the MacBook Pro are the Cinema Displays and Thunderbolt Displays, because, they're made by Apple. They're expensive, but they work perfectly.
My guess is that you bought a cheap MDP to HDMI cable, or have a defective one. From my reading of these boards over the past few months, cheap cables have a high failure rate. And the regular priced ones have only a slightly less of one. Try a new one. Make sure you do not damage the Thunderbolt port. -
I have purchased the VGA Connectors for both a iMac and Macbook Pro so that i can connect my promethean board projector to the computer and I can not get the image on the screen. Does anyone have any suggestions?
Irelandbound wrote:
thank you, I have the adaptors so glad that would work. I just heard adaptors burn out often. So Just thought for my main iMac computer, a plug would be best. I will get one once I move.
Any other suggestions or things I should know about apple products in Ireland. I know there are no Apple stores there.
An adaptor doesn't burn out. It merely serves as a means to connect the power prongs on your device to the power supply.
I believe you are thinking of a transformer, which you do not need. A transformer converts one voltage to another.
You don't need to do that as the power supply of modern electronics can take almost any worldwide voltage.
Look at the label on the device. It should indicate the input power acceptable of 100-240 VAC, 50-60 Hz.
Additionally, I found the adapters cheaper in the UK than I found them in the US. They were available in most supermarket chains. I wasn't in Ireland, so I can't say one way or the other.
If you have something that doesn't have that input power spec, it would require a transformer.
On other items like electric clocks or things with motors, you can connect them up to a transformer and the voltage will be correct, but the frequency may not. For clocks, that will cause them to not keep time well. For motors, they will burn out. -
Hi. I can't get the flash on my iPhone 5 to work. Does anyone have any ideas on how to troubleshoot this. Any help would be appreciated. Thanks.
Tap Camera App > switch to video > see if the flash will turn ON. If still problem, Restore your iPhone with iTunes on computer. See if fixed. If still problem, your iPhone has full Warranty with Apple.
Maybe you are looking for
-
Convert RoboHelp for Word project to RoboHTML
I have a couple projects which are created RoboHelp for Word in RH6. The projects now need to be converted to RoboHelp HTML projects and Flash generated outputs. In conjunction with this I have the following questions: 1) Can RH Word projects be open
-
Netweaver JAVA vs Netweaver ABAP
Hi, I am new to SAP having java background. Going through some of the information provided i have few questions: There are two servers now- Netweaver ABAP and Netweaver JAVA. Are both of these application servers provide same functionality, ie, can I
-
Heap errors in Windows NT 4.0
Running a Java app under JRE version 1.4.1_03-b02 on a PC running NT 4.0 with 256 MB RAM. The app runs 7x24 doing OCR and business logic. The app uses JNI to talk to a C++ DLL, uses Oracle JDBC thin driver, Javacomm 2.0. It has been stable for severa
-
I am not able to open the CC app in the tray or from the progam file. Tried douple clicking the and and also right clicked on the app clicked open. still dosen't open. The app in tray is gray.
-
I Have some photos I took with my DSLR. When I import them to my iphone camera roll they show up as if they are taken today rather than in June 2011 which is the original date of the photos. Is there anyway to change the date of the photos in my came