NAM and NTP

I have a NAM blade in my 6513. I would like the packet captures to be time stamped with NTP time. I configured the NAM to pull time from the switch which uses NTP. There doesn't seem to be a way to get the packets stamped with the NTP time.

Thanks for replies. I have set the time for:
Current NAM System Time: Thu 06 Jul 2006, 09:09:35 PDT
Synchronize NAM System Time With: X Switch
The above shows that time is accurate, the switch gets it's time from NTP and the NAM gets it's time from the switch. The problem is that captures are not time stamped with the NTP absolute times.
Times in the capture decodes start with 0.000, as a reference, and count up from there, not absolute times. Is there a way to make them true NTP times?
I also tried setting the NAM's time source to NTP, using the gateway address for the NTP source. That produced the same results.
There appears to be no real NTP time stamping capability, something that the Fluke Optiview Series II Gigabit sniffer won't do either, even from it's XP OS level.
Thanks again. It appears that I may need to find a better method of using relative times or investigate other types of sniffers to run my tests, the sources of which are done in NTP times but not ethernet.

Similar Messages

  • How to change host name and domain name in installed Cisco Meeting Place Express 2.0?

    Hi
    I have  Cisco Meeting Place Express 2.0 installed on server. Meting Place uses Linux (Red Hat) as base operation system. Please tell me how I can change host name and domain name for Meeting Place Express application to integrate it into corporate domain infrastructure.
    Thanks in advance!!!
    Sincerely yours
    Sergey Bondarenko

    Hi
    Thanks for your attention for my humble problem.
    I have performed Meeting Place Express configuration through the “net” command.
    But now unfortunately I can't connect to meeting place through web browser. I just get blank page.
    Though I can reach the server with help of ssh. I think my DNS works properly because I can resolve the ip address of  cumpxvoice .uclab.com and cumpxweb. uclab.com with help of dig command.
    Have you any idea?
    A lot of thanks in advance!!
    Sincerely yours Sergey Bondarenko
    Here I have printed the net configuration output of Cisco meeting Place Express:
    [root@cumpxvoice root]# net
    This is the MeetingPlace Express network configuration utility.
    Up to the point where you save changes, it is safe to hit ^C to get
    out at any time, in which case nothing will have changed.
    1) List current configuration
    2) Configure Ethernet port 1
    3) Configure Ethernet port 2
    4) Configure service bindings
    5) Set host names
    6) Set domain name
    7) Configure DNS service
    8) Configure NTP service
    9) Configure routing
    10) Done
    Select: 1
    Primary/audio host name: cumpxvoice
    HTTP host name:          cumpxvoice
    RTMP host name:          cumpxweb
    Domain name:             uclab.com
    Service bindings:
    Audio:                   port 1 (eth0)
    Web browsing (HTTP):     port 1 (eth0)
    Web conferencing (RTMP): port 2 (eth1)
    Port 1 (device eth0):
    IP Address:      10.62.60.116
    Network mask:    255.255.255.0
    Default gateway: 10.62.60.1
    Link setting:    autoneg on
    Port 2 (device eth1):
    IP Address:      10.62.60.117
    Network mask:    255.255.255.0
    Default gateway: 10.62.60.1
    Link setting:    autoneg on
    Static routes:
    Destination      Gateway          Network mask     Port
    0.0.0.0          10.62.60.1       0.0.0.0          1
    DNS Servers:
    10.62.60.115
    10.0.1.4

  • Help - Class name and descriptions for a function location.

    Hi Guys
    i have to write a report that displays the class and class descriptions for a function location. the user passes in either the function location(TPLNR) or the class name and  the report should display the the class characteristics and resp. values. Is there a FM that i coud use?
    please help.
    many thanks.
    seelan.

    sadiepu1 wrote:
    When I set up Words with Friends on my Fire it asked for my username and password which from a previous reply to my inquiry above stated that the S 3 doesn't store due to privacy issues. I have tried all my usual combinations of usernames and passwords and my Fire won't let me access the game as it keeps telling me that one or the other is not correct. I have deleted the app from my Fire and re-downloaded it but have the same error comes up. I have accessed the Words with Friends support both on my phone and their website but there is no live chat. I might have to take both to a Verizon store. Also, my Fire won't let me access the game without a correct username and password. To say that I am frustrated would be an understatement as well I have tried everything I can think of with no luck! Thanks for any help you can give!
    Did you use facebook to log in? 
    Verizon will not be able to help you retrieve any of the information you need.  You will have to contact Zynga.

  • I'm having trouble downloading an update to my MacBook Pro. It comes up with my husband's name even though the MacBook is registered under my name and I have my own ITunes acct.  how do I get his name off the ITunes update on my Mac

    I'm trying to download an automatic update from ITunes but when I click on "Update" it comes up with the message, "You have updates available for other accounts" an tells me to sign in to my husband's account, even though the MacBook is registered in my name and I have my own ITunes account.  My husband has his own MacBook and ITunes acct. How do I fix?

    Anything Downloaded with a Particular Apple ID is tied to that Apple ID and Cannot be Merged or Transferred to a Different Apple ID.
    Apple ID FAQs
    http://support.apple.com/kb/HE37

  • Hi. I am using a time capsule for few PC s. I have made 5 different account to access time capsule. but in windows when i enter account name and password for one account, i cannot access other accounts, because windows saves username

    Hi. I am using a time capsule for few PC s. I have made 5 different account to access time capsule. but in windows when I enter account name and password for one account, i cannot access other accounts, because windows saves username. how can i prevent this from happenning. I really need to access all my accounts and dont want it to save automaticlly.

    Why have 5 accounts if you need to access all of them.. just have one account?
    Sorry I cannot follow why you would even use the PC to control the Time Capsule. Apple have not kept the Windows version of the utility up to date.. so they keep making it harder and harder to run windows with apple routers.

  • Reading MS Project column names and data on the fly from a selected View

    Hi guys,
    I have several views on my project file (MSPROJECT 2010) and I want to build a macro so that;
    1. User can select any view ( Views can have diffrent columns and the user may add new columns as well)
    2. User runs the Macro and all the coulmns along with the tasks displayed in the view will be written to a excel file. ( I don't want to build several macro's for each view, I'm thinking of a common method which would work for any selected view)
    The problem I'm facing is that how will i read the column names and data for a particular view on the fly without hard coding them inside the vba code ?
    The solution needs to work on a master schedule as well.
    Appreciate your feedback.

    Just to get you started the following code writes the field name and data for the active task to the Immediate window.
    Sub CopyData()
    Dim fld As TableField
    For Each fld In ActiveProject.TaskTables(ActiveProject.CurrentTable).TableFields
    If fld.Field >= 0 Then
    Debug.Print Application.FieldConstantToFieldName(fld.Field), ActiveCell.Task.GetField(fld.Field)
    End If
    Next fld
    End Sub
    Rod Gill
    Author of the one and only Project VBA Book
    www.project-systems.co.nz

  • How to find out the user name and email address from SAP user id?

    Hi experts,
    In sto3n I find out the the user id with most navigations. I like to know his name or email address to contact him. Which table stores the user details? how to do it?
    Thanks in advance.
    Sharat.

    hi,
    The below tables will give only the name .
    USER_ADDRS
    USER_ADDR
    USER_ADDRP
    USR02
    i think you need email address .
    you can use this Tcode : su01d
    and give the user name and excute it
    i hope it will help you.
    Ram
    Edited by: Ram velanati on Jun 30, 2008 6:57 PM

  • Pdf portfolio source file name and date in file details

    Is it possible to import the source file name and extension as well as the source file created date in the portfolio file details?  Need to document source to portfolio in working with 3rd parties that will only have the original source.  Need to document what was converted into pdf as not all files in a directory will successfully convert to pdf.  Sometimes need to convert 100's of files.  Manual entry is inefficient.  the file names and modified dates are displayed on the Combine Files dialog.  is there a way to capture the detail on that page?

    I don't need the detail of when the pdf was added to the portfolio.  I
    need know which dwg or jpg or word file was converted and the original
    created date of that file for control of information.
    That is impossible; sorry. For some *very specific* types of conversion to PDF the pdfx:SourceModified XMP tag will be set to show the last-modification date of the source file (for example DOCX files converted using MS Word), but there will never be a human-readable record of the source filename or its creation date unless you have manually added them as document XMP properties after conversion (this is what the "Custom Properties" dialog is for). To embed source data automatically would raise no end of privacy and security problems for customers, who most certainly do NOT want their recipients seeing details of internal documents.
    Without writing a plugin there's no access to the internal workflow of the Combine Files dialog, so you cannot use a script to read the names and dates of the files *before* conversion and store them automatically in the new PDF Portfolio's Fields array.

  • TS3276 Cannot send mail from my iPad...."user name and or password is incorrect"......mail can be sent from my iPhone

    Why do I get the message   "Cannot send mail, the user name and or password for my email outgoing server is incorrect"?  I use the same account, etc. on my iPhone and haven't any trouble sending mail.

    If your email requires a password for the SMTP server you can set it up in the settings in the General mail setup. Some i.e Gmail require a password for SMTP.
    Otherwise you will probably get better answers in the iPad forum.
    https://discussions.apple.com/community/ipad/using_ipad

  • What determines whether the Label name and/or Caption appears in the context help window but in other cases, both the label and caption appear in the context help window?

    I am trying to polish an application, and find that I cannot seem to reliably control which of the label or caption text appears in the context help window because I don't understand what rules are in place to determine which should appear. It seems like if I reate a named constant, then use it's right click menu command "Create Indicator" I get a control with only a Label (as long as I don't add a caption). This then appears in the context help window as the label name followed by the description text (after entering some description text). But if I add a caption, the label name is shown in bracket
    s which is a 'feature' I would like to avoid, because I have certain controls where I would like to use a descriptive variable name on the block diagram side without using so much space on the front panel. It seems like there is no way to avoid showing the Label name in the context help for a control/indicator. Is this true?
    I thought the purpose of having a seperate caption was to make the text that appears with a control programmatically controllable, but if that control is not extended to what appears in the context help window, it limits the usefulness of the caption and forces me to re-consider some Label names. However, the problem goes deeper than that because then even when I make the label and caption exactly the same, or if I delete (via a select caption text-backspace or select caption text- delete key .. sequence) the caption for a control, the label name in the context help window still appears in square brackets!
    Can I have complete control over the context help fo
    r a particular control (or has anyone found a third-party context help solution that functions compatibly with LabVIEW 7 in a built application that they will be so kind as to recommend?)
    I have used LabVIEW for three years, and I am now using LabVIEW 7.0.

    Sorry for that.. I was changing the text of my question and didn't read carefully enough in the preview stage. I wanted it to read "What determines whether the Label name and/or Caption appears in the context help window?"

  • Local characters in Name and Address Details

    Hi,
    For an Thailand Employee,
    I need to print his Name from PA0182(Alternative Names) and the Adress Details from Pa0006 with a custom subtype 0026(Thailand Address).
    The source of Name and Address is different if I want to do the same for a Taiwan PERNR.
    Is there a way to dynamically determine the source of Data based on Country Grouping?
    Please suggest.
    Thanks,
    Suryakiran D.

    Sorry for misreading your question!
    In the view T588M, you can choose the infotype 0006 and subtype too it is probably already customized for Thailand!
    There is probrably a feature with county grouping!
    Just add the country grouping of taiwan to the one of thailand!

  • Iphone 4 voice Dial used to work great, but now, I can't get it to recognize voice commands. When i give it a command to call someone, it ends up repeating someone elses name and starts the call. Does anyone know how to solve this problem?

    I have an I phone 4 with 32g.  The voice dial used to work just fine, but now it doesn't recognize the words and ends up saying someone elses name and starts calling the wrong person.  It even won't recognize a number when spoken to it and speaks back and calls the wrong numbers.
    Lately, the phone has really slowed down.  I am not sure if this is the problem.. I have closed all the open apps and deleted any extra picture off the card and extra songs that I have downloaded and the slow problem still exists. 
    Would a reset work to restore the phone to factory settings and if I then resync the phone, would all contacts pictures and songs be restored?
    Ron
    Oklahoma

    What is wrong with your Mac?  You still haven't told us what the problem is. Is the computer still under warranty or Apple Care?
    the next time i attempted to use the computer it wasn't fine
    What do you mean by "wasn't fine".  We can't see your computer so you'll have to describe what your're experiencing in detail without the editorializing.
    Download and run Etrecheck.  Copy and paste the results into your reply. It's a diagnostic tool that was developed by one of the most respected users here in the ASC to help identify the more obvious culprits.

  • The publishing settings page does not open when I click on the domain name and the iWeb application will not stay on the dock.

    Hello,
    I have been trying to help a friend who is having problems publishing her website. (She has done so previously using Mobile me)
    There seem to be a couple of things wrong with the application,
    1     if I drag the application icon onto the dock, it won't stay there
    2     I wanted to change where her site is published to (she has bought a domain name and has a hosting service now) but when I click on the domain name I do not get the "site publishing settings page" so we can't enter the new details.  All that comes up is the main page of her website.
    I would suggest uninstalling and re-installing Iweb, to see if that clears the problem, but as Iweb came pre-installed with her Imac, I am not sure that we can do this.
    Any ideas please?
    she's using and imac 24 in (approx 4 years old) and running osx 10.5.8

    NO - not correct.  Even if you are still using iWeb 08, you can still publish to another host and not MobileMe.  You do this by selecting the option 'Publish to a local folder" and this will publish the site to your desktop and you can then use an ftp programme such as Cyberduck to upload your site to your host.
    MobileMe will not be here after the end of June, so you will have to find alternative hosting.  They are not taking any new subscriptions.
    On new Macs, iLife 11 is pre-installed, but only iPhoto, iMovie and GarageBand are included, not iWeb and iDVD. The Apple Online store is not selling the boxed version of iLife 11 any longer, so if you want to upgrade to iLife, then you'll have to look online at Amazon.com or Amazon.co.uk for a boxed set of either iLife 09 or iLife 11.  Both contains iWeb 09, which is what you would want.

  • Question Regarding Name and Address Clensing

    Hello,
    Can someone help me with understanding the Name and Address Cleansing operatior of OWB.
    I am currently using OWB Client 9.2.0.2.8
    Before using the Name and Address operator should you do any configuration for it to function? Based on the viewlet which i tried there were no configuration steps and once i finished doing the steps in the demo there were rows inserted but with *null data.
    Is Trillium packaged with the OWB or should you still purchase it?
    Thank You

    Thank you for the information Mark, I still have another question.
    Here is my situation:
    I have been tasked to integrate a 3rd party DQ ventor to the name and address cleansing operator of OWB. In relation to that I have downloaded the OracleAdaptorKit provided by Oracle for such development. The problem is I still dont really understand how the whole thing works. My understanding is that once you use the Name and Address operator in a Map and execute the it OWB will call the Name and Address Server which will trigger the Adaptor (which should be created by the vendor or me in this case) that will do the Parse() function based on the libraries of the 3rd party DQ vendor. Is my understanding correct?
    My second question is on how will the Name and Address Engine call the Adaptor(JAVA applet?) which will use the Parse() function and what are the values that Name and Address Engine throw to the Adaptor? And how will you know if you have successfully created a connection between the Name and Address Engine and the Adaptor you created?
    My third question is in regards to the components to be created. So given that the Name and Address Engine is by default installed with OWB does that mean that the only thing left to program are the Adaptor and Libraries?
    I hope you can help me, Thank You

  • Old name and password won't work when networking to new Win7PC.

    I have a name/password problem when trying to network a new Win 7 PC via a new Netgear 2200 Router to a MacMini.
    It networked 100% OK with the old XP System and old Netgear Router, but now when I click on the PC icon that shows up in Workgroup the old password doesn't work and there is a different popup menu that won't allow the old name and password.
    Interestingly the Mac Mini still networks with the XP laptop using the old pupup box with name and password.
    Netgear say it's not their problem - even though they list 'mac compatible' on their box.
    The PC manufacturer (Acer) say Mac issues are outside of their free technical support.
    Apple support said the Macmini was 'out of warranty'.
    So I'm stuck using a USB stick or email to transfer files from one to the other!
    Please help, I need that network connectivity back asap.

    Option 1
    If you've enabled root logins, log in as root and promote the other user to an admin.
    Option 2
    Recover your entire system from the last Time Machine snapshot taken before the damage was done, if you know when that was. Afterwards you can restore any data that has changed since then from a later snapshot. If you’re an advanced user familiar with the shell, there may be a quicker fix, but I prefer not to get into that.
    Option 3
    Back up all data, then boot in single-user mode (command-S at startup.) When the text stops scrolling, follow the prompts to make the boot volume writable. Then enter the following command very carefully:
    rm -i /var/db/.AppleSetupDone
    You should get the following line of output below what you entered:
    remove /var/db/.AppleSetupDone?
    If you do, then enter
    y
    and press return. Then type
    reboot
    Press return again. The system will boot into the Setup Assistant, as if you were setting it up for the first time. Skip the prompt to transfer information. Create a user with the same name as the old admin user. Log in and test. You may need to recreate your other user accounts, if any. Their files won't be deleted.
    Option 4
    If you're not comfortable with any of the above options, get someone more experienced to help you. One way to do that is to make a "Genius" appointment at an Apple Store. It's a free service.

Maybe you are looking for