Need for 2 vlan to ping to each other
Hi
On a 3750 I have configure a new vlan 114 and assigned it the adress 192.168.114.254, I've put my port in trunk mode with with the other vlan wich is vlan 1 192.168.14.254. I would like for both network to ping each other, when I received a adress from the dchp I get 192.168.14.20/24 with the gateway 192.168.14.254
Thanks for your help
You will need to setup SVIs (Switched Virtual Interfaces) or connect the switch to a router so traffic between the two VLANs can be routed. Take a look at the following link for more info/explanation:
http://www.cisco.com/c/en/us/td/docs/ios/12_2/switch/configuration/guide/fswtch_c/xcfvl.html
Thank you for rating useful posts!
Similar Messages
-
PCs connecting to ME3400 Switch not pinging to each other!!
hi,
We have a new ME-3400-24TS-A Switch.Its a 24 10/100 Mbps switch.But when we connect the two PCs on its any of the two ports ,they are not pinging to each other.Both the PCs are in the same Network.
basic switching is not happening.Kindly help me!!The IOS version is :S340XBT-12225SEG
Cisco ME 340X SERIES IOS METRO BASE W/O CRYPTO TARThe ports in the same vlan don't do local switching per default on a ME3400. You have to enable local switching for a vlan with the commands "vlan xxx" and "uni-vlan community".
But, only 8 ports can be in the same vlan. So, maybe you have choose the wrong switch if you need a normal L2 switch. Normally, in Metro Ethernet you don't want local switching between user ports.
I hop this helps. Please rate all posts.
Cheers
Rene -
I have two location one is Delhi(IP-192.168.100.*) and another is Mumbai(IP-192.168.1.*) and both are connected by MPLS line and ping with each other.
We have one DC in Delhi location and domain name is CAPLDC and Delhi location all PC is member of this domain and working properly.
now i am trying join the Mumbai location PC with my Domain(CAPLDC) but they are not join with my DC and generate the error.
I have chek the DNS and nslookup all are correct but this is generate error.
Is this possible Mumbai location join with this Domain(CAPLDC)???
One more thing when i have created another DC with this name (papldc.com) then Mumbai location is joined properly.
Pls find the error message below and also find the attachment.
Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt.
The domain name "capldc" might be a NetBIOS domain name. If this is the case, verify that the domain name is properly registered with WINS.
If you are certain that the name is not a NetBIOS domain name, then the following information can help you troubleshoot your DNS configuration.
DNS was successfully queried for the service location (SRV) resource record used to locate a domain controller for domain "capldc":
The query was for the SRV record for _ldap._tcp.dc._msdcs.capldc
The following domain controllers were identified by the query:
capldcserver.capldc
win-dyfq2poc88q.capldc
However no domain controllers could be contacted.
Common causes of this error include:
- Host (A) or (AAAA) records that map the names of the domain controllers to their IP addresses are missing or contain incorrect addresses.
- Domain controllers registered in DNS are not connected to the network or are not running.
Pankaj KumarWhy are you using a single labeled domain? I would recommend renaming the domain name to be something like domain.com.
Please refer to the articles below to fix your current issue:
http://www.wincert.net/tips/networking/1614-cant-join-pc-to-a-domain-with-single-label.html
http://www.itgeared.com/articles/1128-using-single-label-dns-names-for-active/
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile -
My wife and I have Iphone 5's. For some reason, we can call each other, no problem, but if we text she receives my texts but I don't recieve hers. Any one ever have a problem like this, and more importantly, a solution? Thanks!
In Settings> Messages
make sure iMessage is turned on, and
in Settings> Messages> Send & Receive...
make sure you have your phone number listed under "you can be reached by imessage at" -
Anyconnect VPN peers cannot ping, RDP each other
I have an ASA5505 running ASA 8.3(1) and ASDM 7.1(1). I have a remote access VPN set up and the remote access users are able to log in and access LAN resources. I can ping the VPN peers from the remote LAN. My problem that the VPN peers cannot ping (RDP, ectc..) each other. Pinging one VPN peer from another reveals the following error in the ASA Log.
Asymmetric NAT rules matched for forward and reverse flows; Connection for icmp src outside:10.10.10.8 dst outside:10.10.10.9 (type 8, code 0) denied due to NAT reverse path failure.
Below is my ASA running-config:
ASA Version 8.3(1)
hostname ciscoasa
domain-name dental.local
enable password 9ddwXcOYB3k84G8Q encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.1.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address dhcp setroute
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns domain-lookup inside
dns server-group DefaultDNS
name-server 192.168.1.128
domain-name dental.local
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network RAVPN
subnet 10.10.10.0 255.255.255.0
object network NETWORK_OBJ_10.10.10.0_28
subnet 10.10.10.0 255.255.255.240
object network NETWORK_OBJ_192.168.1.0_24
subnet 192.168.1.0 255.255.255.0
access-list Local_LAN_Access remark VPN client local LAN access
access-list Local_LAN_Access standard permit host 0.0.0.0
access-list DefaultRAGroup_splitTunnelAcl standard permit 192.168.1.0 255.255.255.0
access-list VpnPeers remark allow vpn peers to ping each other
access-list VpnPeers extended permit ip object NETWORK_OBJ_10.10.10.0_28 object NETWORK_OBJ_10.10.10.0_28
pager lines 24
logging enable
logging asdm informational
logging mail informational
logging from-address [email protected]
logging recipient-address [email protected] level informational
logging rate-limit 1 600 level 6
mtu outside 1500
mtu inside 1500
ip local pool VPNPool 10.10.10.5-10.10.10.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-711.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static any any destination static RAVPN RAVPN
nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
nat (inside,outside) source static any any destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
object network obj_any
nat (inside,outside) dynamic interface
object network RAVPN
nat (any,outside) dynamic interface
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community *****
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA-TRANS mode transport
crypto ipsec transform-set ESP-DES-SHA-TRANS esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-192-SHA-TRANS esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA-TRANS mode transport
crypto ipsec transform-set ESP-AES-256-SHA-TRANS esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-SHA-TRANS mode transport
crypto ipsec transform-set ESP-3DES-SHA-TRANS esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA-TRANS mode transport
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-192-SHA ESP-AES-256-SHA ESP-3DES-SHA ESP-DES-SHA ESP-AES-128-SHA-TRANS ESP-AES-192-SHA-TRANS ESP-AES-256-SHA-TRANS ESP-3DES-SHA-TRANS ESP-DES-SHA-TRANS
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto ca trustpoint LOCAL-CA-SERVER
keypair LOCAL-CA-SERVER
crl configure
crypto ca trustpoint ASDM_TrustPoint0
enrollment self
subject-name CN=ciscoasa
keypair billvpnkey
proxy-ldc-issuer
crl configure
crypto ca server
cdp-url http://ciscoasa/+CSCOCA+/asa_ca.crl
issuer-name CN=ciscoasa
smtp from-address admin@ciscoasa
crypto ca certificate chain LOCAL-CA-SERVER
certificate ca 01
**hidden**
quit
crypto ca certificate chain ASDM_TrustPoint0
certificate 10bdec50
**hidden**
quit
crypto isakmp enable outside
crypto isakmp policy 10
authentication crack
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto isakmp policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto isakmp policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.1 255.255.255.255 inside
telnet timeout 5
ssh timeout 5
console timeout 0
management-access inside
dhcpd auto_config outside
dhcpd address 192.168.1.50-192.168.1.99 inside
dhcpd enable inside
threat-detection basic-threat
threat-detection statistics
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
ssl trust-point ASDM_TrustPoint0 outside
webvpn
enable outside
svc image disk0:/anyconnect-win-3.1.04072-k9.pkg 1
svc profiles DellStudioClientProfile disk0:/dellstudioclientprofile.xml
svc enable
tunnel-group-list enable
internal-password enable
smart-tunnel list SmartTunnelList RDP mstsc.exe platform windows
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.1.128
vpn-tunnel-protocol l2tp-ipsec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value DefaultRAGroup_splitTunnelAcl
default-domain value dental.local
webvpn
svc modules value vpngina
group-policy DefaultRAGroup_1 internal
group-policy DefaultRAGroup_1 attributes
dns-server value 192.168.1.128
vpn-tunnel-protocol l2tp-ipsec
default-domain value dental.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.1.128
vpn-simultaneous-logins 4
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
group-lock value RAVPN
split-tunnel-network-list value Local_LAN_Access
default-domain value dental.local
webvpn
url-list value DentalMarks
svc modules value vpngina
svc profiles value dellstudio type user
svc ask enable default webvpn
smart-tunnel enable SmartTunnelList
username wketchel1 password 5c5OoeNtCiX6lGih encrypted
username wketchel1 attributes
vpn-group-policy DfltGrpPolicy
webvpn
svc profiles value DellStudioClientProfile type user
username wketchel password 5c5OoeNtCiX6lGih encrypted privilege 15
username wketchel attributes
vpn-group-policy DfltGrpPolicy
webvpn
svc modules none
svc profiles value DellStudioClientProfile type user
username jenniferk password 5.TcqIFN/4yw0Vq1 encrypted privilege 0
username jenniferk attributes
vpn-group-policy DfltGrpPolicy
webvpn
svc profiles value DellStudioClientProfile type user
tunnel-group DefaultRAGroup general-attributes
address-pool VPNPool
authorization-server-group LOCAL
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
tunnel-group DefaultRAGroup ppp-attributes
authentication pap
authentication ms-chap-v2
authentication eap-proxy
tunnel-group RAVPN type remote-access
tunnel-group RAVPN general-attributes
address-pool VPNPool
authorization-server-group LOCAL
tunnel-group RAVPN webvpn-attributes
group-alias RAVPN enable
tunnel-group RAVPN ipsec-attributes
pre-shared-key *****
tunnel-group RAVPN ppp-attributes
authentication pap
authentication ms-chap-v2
authentication eap-proxy
tunnel-group WebSSLVPN type remote-access
tunnel-group WebSSLVPN webvpn-attributes
group-alias WebSSLVPN enable
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
smtp-server 173.194.64.108
prompt hostname context
hpm topN enable
Cryptochecksum:3304bf6dcf6af5804a21e9024da3a6f8
: endHi,
Seems to me that you could clean up the current NAT configuration a bit and make it a bit clearer.
I would suggest the following changes
object network VPN-POOL
subnet 10.10.10.0 255.255.255.0
object network LAN
subnet 192.168.1.0 255.255.255.0
object-group network PAT-SOURCE
network-object 192.168.1.0 255.255.255.0
network-object 10.10.10.0 255.255.255.0
nat (inside,outside) source static LAN LAN destination static VPN-POOL VPN-POOL
nat (outside,outside) 1 source static VPN-POOL VPN-POOL destination static VPN-POOL VPN-POOL
nat (any,outside) after-auto source dynamic PAT-SOURCE interface
The above should enable
Dynamic PAT for LAN and VPN users
NAT0 for the traffic between LAN and VPN
NAT0 for traffic between VPN users
You could then remove the previous NAT configurations. Naturally please do backup the configuration before doing the change if you wish to move back to the original configuration.
no nat (inside,any) source static any any destination static RAVPN RAVPN
no nat (inside,outside) source static NETWORK_OBJ_192.168.1.0_24 NETWORK_OBJ_192.168.1.0_24 destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
no nat (inside,outside) source static any any destination static NETWORK_OBJ_10.10.10.0_28 NETWORK_OBJ_10.10.10.0_28
no object network obj_any
no object network RAVPN
In the event that you dont want to change the configurations that much you might be fine just by adding this
object network VPN-POOL
subnet 10.10.10.0 255.255.255.0
nat (outside,outside) 1 source static VPN-POOL VPN-POOL destination static VPN-POOL VPN-POOL
But the other above configurations changes would make the current NAT configurations simpler and clearer to see each "nat" configurations purpose.
- Jouni -
I have a MB pro (10.7.5) and two PC's(windows 7). I am unable to ping either of PC through Mac. However, Both PC's reply ping made to each other and to Mac as well. Help me with this. Searched Internet. Cant resolve till now
Regards
MacIts.Request timeout for icmp_seq 0
Request timeout for icmp_seq 1
Request timeout for icmp_seq 2
Request timeout for icmp_seq 3
Request timeout for icmp_seq 4
Request timeout for icmp_seq 5
Request timeout for icmp_seq 6
is the reply m getting. -
Is it possible for two admin setups to control each other?
Hi,
I have the admin portion installed on mac pro that is specifically managing 3 workstations on a private subnet. I have installed the same ARD 3.2 I guess admin version on my Mac Pro. I want to be able to use ARD to connect to the admin console that is on my subnet and in turn be able to control the 3 clients.
I can see the admin console but it won't connect to it. And when I go over to that admin console and try to connect to my Mac, it won't.
Is there an issue with two admin console trying to connect? Does it have to be a admin/client relationship only?
Thanks
Grego I installed from our 10 server license pack.
Note that it's actually a 10 client license, not a 10 server license. As Templeton said, for each system on which you want to install the ARD administration application, you need to purchase a separate copy of ARD.
How do I get different serial numbers on each machine from the same license pack?
You don't. If you want to have the administrator application installed on two systems, you will need to purchase a second 10-client copy of ARD.
Message was edited by: Dave Sawyer -
How to make 2 clients on same VLAN communicate to each other when tunnel-loop-prevention is enabled?
Requirement:
How to make two clients on same VLAN communicate to each other when tunnel-loop-prevention is enabled on tunneled-node configuration at controller?
Whenever we enable tunnel-loop-prevention on controller while we configure tunneled-node, the communication between two tunneled-node client on same VLAN is blocked or dropped.
If the tunneled-node clients are of different VLANs then they can communicate between them even when the tunnel-loop-prevention is enabled on the controller.
Solution:
To make two tunneled-node client on same VLAN to communicate between them, we need to enable "local-proxy-arp" for the interface VLAN on the controller.
Once it is enabled now the tunneled-node clients on same VLAN can communicate between each other.
Configuration:
To enable "local-proxy-arp":
Get to the interface of the VLAN on the controller
Example :
(config)#interface vlan 5
(config)#ip local-proxy-arp
To enable tunnel loop prevention on controller
(config)# tunnel-loop-prevention
Verification
Show commands:
To check if tunnel-loop-prevention is enabled or disabled
#show tunneled-node config
Tunnelded node Server: Enabled
Tunnel Loop Prevention: Enabled
To check if local-proxy-ap is enabled:
#show interface vlan 5
Look for in the output "ProxyARP enable"streetfi8er wrote:
Server ready,waiting for client:
Exception in thread "New THREAD" java.lang.NullPointerException
at server4$server4Thread.run(server4.java:88)
Failed to accept client
when i run the second client programme on different a console in the same system i get the error that:
Unknown HostOK, I'm no socket programming expert; but I can see a few potential problems with what you've written.
1. First off, which line is line 88? Line numbers would be useful. Also, indenting your code properly would make it easier to read.
2. Your 'while(!str.equalsIgnoreCase("close"))' will always fail with a NullPointerException because 'str' is initially set to null.
3. Your 'while(true)' loop worries me. How does it exit? Relying on an exception is usually very bad practise.
4. You are not handling SecurityExceptions. While it's unlikely to happen on your machine; it could easily happen on another.
5. It might be worth indicating the actual exception thrown in your "Failed to accept client" message. accept() can throw three different types of IOException.
6. All the threads you create will be called "New THREAD", which doesn't provide much value.
HIH
Winston -
Just bought a new Macbook and it's on the same subnet as my iMac. I have the firewall running in stealth mode on both machines. Neither one sees the other and Finder sidebar does not show any "shared" computers.
I'm assuming that I need to disable the firewalls for these two machines to see each other.
The question is: Once these two machines have located each other, will turning on the firewall in stealth mode shut down the sharing once more, or will it stay active?Got it working. Disabled the firewalls, set up the sharing, set up the user accounts (different user names on different machines thanks to the Migration Assistant) and away it went. Re-established the firewalls and everything is cool.
Interesting how working on Macs changes ones thinking. I've become so used to everything just working well that I just slap things together without any advanced thinking -- on occasion that bites back. It didn't help that from a security standpoint, I had tightened down every nut I could find. If these had been Windows machines, I would've planned much more thoroughly and would have expected and anticipated trouble at every step of the way.
Thanks -
I need to make 3 vlans to ping one another
Hello I have a problem and I need to connect 3 different vlans that have a full class c address to each other. I am also using a spanning tree which I am allowed to use any address I like so I already set it up. Any help would be greatful. I am not really good packet tracer as I am using an example in my work :/
I added the file that I am using in the Packet tracer.Hi Jack,
A small correction on your DHCP scope configuration. It looks like you have configured wrong default gateway's on your DHCP scope.
Your Current Configuration
ip dhcp pool vlan5
network 198.1.253.0 255.255.255.0
default-router 195.1.253.254
ip dhcp pool vlan10
network 198.1.255.0 255.255.255.0
default-router 195.1.255.254
Modified DHCP Scope Configuration
ip dhcp pool vlan5
network 198.1.253.0 255.255.255.0
default-router 198.1.253.254
ip dhcp pool vlan10
network 198.1.255.0 255.255.255.0
default-router 198.1.255.254
Once you correct this verify the PC's are picking the correct gateway address and try pinging between the vlans. That should work.
Regards
Najaf
Please rate when applicable or helpful !!! -
Can i use my creative cloud membership on laptop and desktop? Or is one membership needed for each device?
Yes you can!
-
I see people from different ages at my work and every month I need to count how many people from each age I've seen that month. How can I do to give the entries to numbers in a single cell and make numbers count them for me? The final result would be a spreadsheet telling there were 8 people from 20 to 39 years old, 14 peolple from 40 to 59 and so on...
jpqcampos wrote:
This appears to be an 'input form' using 'Radio Buttons' to select the category. Neither of these features are supported in Numbers '09.
You can input the data on one table and summarize it on a second table, but the input table will continue to hold data for each event.
And by using the Reorganize button, you can hide all but two rows of that table to approximate the appearance and performance of an input form.
Here are the two tables, Data on the left and Summary on the right. Notes below.
The grey-filled columns in both tables are 'working' columns, and may be hidden (as shown in the image below).
Data table:
D1 contains the word "TRUE" (in capital letters). (This row is always shown.)
D2 is empty, or may contain any value except "TRUE" (This row is always hidden under the Reorganize rule.)The rest of Row 2 of this table requires the data shown: a number outside the range to be counted (999), and two checkboxes, both checked.
D3 (and filled down the rest of column D): =AND(OR(B2,C2),NOT(OR(B3,C3)))
The formula returns TRUE only for the first unused row in the table (ie. the first row for which neither checkbox has been checked)
Summary table:
Column A contains labels for the age ranges to be counted.
Column B contains the same information in the form necessary for the formulas in columns C and D. They need a numeric value, and that value must be the largest acceptable value in the range to be counted.
C2 (and filled right to column D, then both filled down to row 5):
=COUNTIFS(Data :: $A,"<="&$B,Data :: B,TRUE)-SUM(C$1:C1)
Two changes from the previous example:
COUNTIFS is used to separate the Native and Foreign counts as well as the age range to be counted.
The amount subtracted from each result is the SUM of the earlier results, and includes the text value in the first cell of the column (which is interpreted by SUM as a zero).
See note below regarding my earlier formula.
When the greyed columns are hidden and the checkbox in the Reorganize pane is checked, the two tables will appear as shown below:
Close the reorganize pane, and the 'data entry form' is ready to use.
To use, enter the age first, then check one of the boxes.
As soon as one box is checked, the row will be hidden, and the next (unused) row will be shown.
Regards,
Barry
Note regarding formula in my earlier post:
The earlier formula will give erroneous results as it subtracts only the count directly above it from its count of persons in the age range 0-n.
In E2 of that table, replace "-E1" with "-SUM(E1:E$1)
Fill down to E8.
Ignore the instructions (in that post) following "Fill down to E8."
B -
I just updated to 10.8 Mountain Lion from 10.7.5. Now I must enter my admin password each time I attempt to access my main hard drive. How do I reverse the need for the password? It's a real PAIN!
I'd think you have a Keychain problem (Keychain storing passwords and the likes).
When you are being asked, are you offered the checkbox, "Remember this password in my Keychain"? If so, check and see if it stops asking. -
How do you change apple id for icloud if phone is already set up. Need to give each phone in my account their own apple id for icloud so that we dont receive each others messages but can still all use same id for purchases.
Settings-icloud-scroll to the bottom, select delete, if you want to keep the content select keep, otherwise it'll remove it. Then once it is done add the account information for the account you want on that phone. Your apple ID in settings-store will remain the same and each device can still purchase/use content from that account.
-
On a port or vlan that doesn't need acl filtering is it more effecient to have nothing or a single permit ip any any? I understand that there's a default implied deny ip any any to block anything not allowed in a proceeding permit statement but I assume that only applies if an acl is assigned so I would think if you're going to just permit ip any any in an acl with out any denying before it i's better not to waste any processor time running packets through an acl filter since there's nothing to be rejected anyway.
Hi Vini, if I interpret correctly, there is no need for an acess list as it just takes system resources for no need.
-Tom
Please mark answered for helpful posts
Maybe you are looking for
-
Logic 7.1, 10.3.9 and MT4 NOT WORKING
Latest drivers from Emagic but the MT4 is not working in 10.3.9 and Logic. audio/midi prefs see the MT4 but the usb-light won't come on at starting Logic. MT4 is OK and working perfect under OS 9.2 for instance. Even tried another MT4 with same resul
-
Problem using ant 1.6.2 scripts for weblogic 8.1
hai, i downloaded ant 1.6.2 and started writting ant scripts. these ran fine when i am doing jobs related to websphere application server but they are failing when i am running the same targets in weblogic. i know that this problem is mainly due to t
-
How to get the online user who are browse some view?
i want to get the current users who are browsing some view in EP6.additonal:which is developed as web dynpro project.
-
Is there a way to control the section prefix (chapter, section, ...) to say something else ?
i would like to use different section prefix text than author uses by default. i would not find a way to change the text anywhere.
-
How Do I uninstall all versions of Firefox silently via script?
I have been tasked to remove Firefox from 200 computers in our company due to security reason. I have scanned all the computers for versions of firefox installed on them and noticed there are different versions of firefox on our computers. I need to