Need help f8 format

Recently I've had some malware problems with my PC, and to deal with it I've decided that I am going to format.
I turn on my PC, and press F8 for advanced boot options.
Select Repair my PC.
It loads a bit, then I encounter a problem on startup I get to the logon screen and all it shows is "other user" with the username/pass fields blank.
this is my personal computer and has only one user account. Mine, which is the administrator.
The problem is, that when I enter the information for this account, which is the only one on my PC, It says that it is not recognized or cannot be contacted.
If anyone has experienced similar problems, or if this is NOT referring to a user account but something else instead, I would greatly appreciate some help from you. Thanks!

I used the function key (if the key is f8) but when it get to "repair my pc" then it goes to "Other User" log on page and no password/user name I have ever used will work. I need a way to start up recovery without using the f8 or the installation cd's (which
I Don't have). I do Thank You for your reply.

Similar Messages

Need help in formatting the Date - Date does not

Need help in formatting the Date - Date does not formats and give Not a valid month error in the below scenario.
select oc.ST_PGM_MGR, r.ag_dnum, get_major_work_type(r.perf_eval_rtng_id) "v_work_code", r.ag_dnum_supp "supp", r.intfinal, to_char(r.formdate,'MM/DD/YYYY') "formdate", to_char(r.servfrom,'MM/DD/YYYY') "srv_from", to_char(r.servto,'MM/DD/YYYY') "srv_to", descript, add_months(to_char
--- Bellow line of Code on trying to format it to mm/dd/yyyy gives the error
(r.formdate, 'DD-MON-YYYY'),12) "formdate2"
from table REdited by: Lucy Discover on Jul 7, 2011 11:34 AM
Edited by: Lucy Discover on Jul 7, 2011 1:05 PM

Your syntax is wrong - look at the post above where this syntax is given:
to_char (add_months(r.formdate,12), 'MM/DD/YYYY') "formdate2"Look at the formula from a logical perspective - "inside out" to read what is happening -
take formdate, add 12 months
add_months(r.formdate, 12)then apply the to_char format mask - basic syntax
to_char(date, 'MM/DD/YYYY')Compare to your syntax:
to_char(add_months(r.formdate, 'MM/DD/YYYY'),12) "formdate2"You will see your format string inside the call to add_months, and your 12 inside the call to to_char.
Good luck!

Need help for Format HD

Hi I need Help for Formating HD so Wat Key need hold on start up for format HD I apprciated you Help

Jesus:
Formatting, Partitioning Erasing a Hard Disk Drive
Warning! This procedure will destroy all data on your Hard Disk Drive. Be sure you have an up-to-date, tested backup of at least your Users folder and any third party applications you do not want to re-install before attempting this procedure.
• With computer shut down insert install disk in optical drive.
• Hit Power button and immediately after chime hold down the "C" key.
• Select language
• Go to the Utilities menu (Tiger) Installer menu (Panther & earlier) and launch Disk Utility.
• Select your HDD (manufacturer ID) in left side bar.
• Select Partition tab in main panel. (You are about to create a single partition volume.)
• _Where available_ +Click on Options button+
+• Select Apple Partition Map (PPC Macs) or GUID Partition Table (Intel Macs)+
+• Click OK+
• Select number of partitions in pull-down menu above Volume diagram.
(Note 1: One partition is normally preferable for an internal HDD.)
• Type in name in Name field (usually Macintosh HD)
• Select Volume Format as Mac OS Extended (Journaled)
• Click Partition button at bottom of panel.
• Select Erase tab
• Select the sub-volume (indented) under Manufacturer ID (usually Macintosh HD).
• Check to be sure your Volume Name and Volume Format are correct.
• Click Erase button
• Quit Disk Utility.
cornelius

Need help in formating a form dealing with negative currency

Need Help!!!
Creating forms in Adobe acrobat Pro I could format a number cell to calculate additions/subtractions of currency. If the result was negative I could get the cell to show the negative result in red text and show parentheses around them. How can I do that in LiveCycle?
If i have to use formcalc - what would i type in?

In LiveCycle can be done using the Numeric Field object and some formcalc script.
Use the "Numeric Field" from the Object Library. For the Field patterns (Select the placed numeric field, On object Window Object -> Field) use "num.currency{}" to show the currency(Ex: $) and "parentheses" if its negative. Write some script to show red text/border in red .
On exit event of the Numeric Field here is the script:
if($.rawValue <0) then $.font.fill.color.value = "255,0,0" endif // This will make entire text in red color if the value is negative.
if($.rawValue <0) then $.validate.nullTest = "error" endif //This will make border of the field in red color if the value is negative.
Hope this helps.

Need Help with Format/Partition.. using cmd

Okay guys.. Im kinda sick of trying to get my Recovery to work. Seems like its about to finish and everything is perfect.. then suddenly I get an error message saying that Recovery didnt work, or something like that..
I figured I might as well try starting with a fresh hard drive, then trying the recovery again..
So someone told me that if I have the HP Recovery disks, then I would be able to try them, even on a brand new hard drive, or a formatted one or whatever..
Is this true?
If so, then what I am asking you guys, is, if there is anybody that would be able to help guide me thru the steps needed, in order for me to Format my hard drive, & then partition it or whatever…
& I wanna be able to do all this, using cmd (command prompt)
So Please.. anyone.. your help would be greatly appreciated..
I have an HP Pavilion dv6653cl
Thanks!!

Hi,
There's no need to pre-format a new Hard Drive - if you perform a 'Factory Reset' using your Recovery Discs, these will perform a quick format and also re-create all the original partitions on the new drive as part of the process.
A complete guide to using Recovery Discs can be found on the relevant link below.
Performing An HP System Recovery - Windows 7.
Performing An HP System Recovery - Windows Vista.
Performing An HP System Recovery - Windows XP.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Need help in formatting the report created using SSRS

I have created an image and used it as the body background. But I want that image to come at right
Set bodyRepeat as RepeatY.
Currently its showing as below I need this blue image at the right most side of the report as below
Also I need to display text on the image.
Need Help!!!
Abhinav

Hi AbhinavSultania,
According to your description, you created a report and added background image to it, you want to display the image at right side of the report and display text on the image.
According to my knowledge, we could not control position of background image, as a workaround, we can refer to the following steps:
Create an image with the blue line at right side of it using Paint.
Right-click body of the report to open Body Properties dialog box, then import the image as background image.
Drag text box from Toolbox to the blue line of the image. Right-click inside of the text box and click Expression, we can use expression to show dynamic contents at runtime.
The following screenshot is for your reference:
If you have any more questions, please feel free to ask.
Thanks,
Wendy Fu
Wendy Fu
TechNet Community Support

Need help in formatting a number field with same precision for excel output

I am trying to get the same preciision for a field in RTF template when the output is in EXCEL
i.e. same number of digits after decimal. So, I would like to show 150 as 150.00 and 123.2 as 123.20 etc !! Is there a way to do it. the Built in formatting will not display 150.00 for 150 . but if i add $ symbol it will display. But i dont need $ syambol. please help.

I found this on one of the forum questions.
Excel dont preserve the trailing zeros.
try opening the xcel and type 5.0000 and tab out, it wont preserve the trailing zeros after decimal.
try finding out how to disable the option in excel. if you do that, you will see what you send out from the report.
But you can try to convert the number into a text by trying to append a space at the beginning. See if that would work.
Thanks
Swarna

I need help in formating in Pages

I need formating help in Pages: I need two columns for text, but other text not in the columns. How do I do both?

Hi Mandy,
I'm not sure if I've understood what you want to do, but here's an example, based on what you've said. These instructions apply to a word processing document.
The Columns control button toward the right end of the format bar is used to set the number of columns. It's the dark one (indicating it's been selected) just above the top left corner of its menu in the image:
The 'other' text (I've called it 'extra text' in the image) can be placed in a text box. Click the T in the toolbar to insert a text box, resize to fit your 'other' text, and position as desired.
One recommendation I'd make to everyone learning to use Pages is to download and read through the first few chapters of the Pages '09 User Guide. Then check in the other chapters when you want to learn how to use specific features of Pags.
You'l find a download link in the Help menu in Pages.
Regards,
Barry

I need help to format my laptop

I am Brazilian and do not speak well in inbles, please forgive me first of all. I want to ask for help at all, I'm having trouble formatting my Toshiba laptop I bought with windos 8, I want to downgrade to windows 7. Cant work the DVD system.
photo:
Solved!
Go to Solution.

Once you change the bios your hard drive will show up to install windows 7, sometimes the bios will need to be updated before the CSM option will appear.
INSTRUCTIONS:
First - Burn recovery media before you make any changes! -you may want or need to go back to windows 8 later-
Second -
Important Bios changes when changing from Windows 8 to Windows 7:
Completely shut down laptop (Shut down Windows 8 while pressing the Shift key to completely power off.) then restart computer and hold f2 when the screen goes black and wait for the bios setup utility to launch.
Select advanced, then system configuration, then boot mode
UEFI and CSM or legacy (UEFI for Windows 8 and CSM or legacy for windows 7)
For windows 7 change to CSM or Legacy mode.
Third - Also in bios setup utility select - Security, then Secure Boot, then you have to disable secure boot for windows 7.
You will need to delete all partitions before installing windows 7 this is done forth step.
Forth - Insert your windows 7 disc and select custom install, your partitions should show up - click on each one and below you will see advanced drive options, click that and you will have options to format - format each one, then delete each one. You will be left with one raw partition, select to install and windows will do the rest while installing the operating system.
Fifth - install drivers
Installation order is important:
Install chipset driver then video driver before other drivers. Then install Toshiba Value added package before other applications
Your support page is here - http://support.toshiba.com/support/modelHome?freeText=1200007943
These windows 7 64 bit drivers may work for Satelite C55-A5105 - http://www.toshiba.eu/innovation/download_drivers_bios.jsp?service=EU&selCategory=2&selFamily=2&selS...
Post your results!
S70-ABT2N22 Windows 7 Pro & 8.1Pro, C55-A5180 Windows 8.1****Click on White “Kudos” STAR to say thanks!****

Need help - Date format in es Tag / LoadedData

hi,
I have one Date attribute called 'EXPIRATION_DATE' in DOCUMENT table.
I mapped this column entry in 'application-config.xml' as jdbc.column.EXPIRATION_DATE=ExpirationDate;
And when I am trying to get this value in JSP,within '<es:forEachInArray>' tag
scope, using the syntax below
<%
String strDate = (String)doc.getProperty("LodedDate","ExpirationDate");
%>
I am getting different formatted results in different environments
Like , when I executed this in windows ,
I got the resulted string as "Mon Jul 07 00:00:00 EDT 2003" , which can be converted
to 'Date' type
using <% Date exp_date = new Date(strDate); %> which solves my problem.
But , when I executed same code to UNIX ,
I got the resulted string as "2009-02-01 00:00:00.0" , which is not convertible
to 'Date' format.
I got the following exception , when I try to convert this resulted String to
date format like.
<% Date exp_date = new Date(strDate); %>
java.lang.IllegalArgumentException
at java.util.Date.parse(Date.java:585)
at java.util.Date.<init>(Date.java:267)
Finally , I need to convert the resulted string to "MMM dd, yyyy" (Feb 22, 2000)format.
If not above method , what is the best way to get the resulted value in this "MMM
dd, yyyy" format.
/***** My Sample code ********/
<es:forEachInArray array="<%=BankerMsgs%>" id="doc" type="Content" >
<%String strDate = "";
     strDate = (String)doc.getProperty("LodedDate","ExpirationDate");     //strDate =
"Mon Jul 07 00:00:00 EDT 2003"; // Windows
     //strDate = "2003-07-07 00:00:00.0"; // UNIX
     out.println("Original Date is :" + strDate); // In windows env I got this formatted
result 'Mon Jul 07 00:00:00 EDT 2003' and In UNIX I got the string as '2003-07-07
00:00:00.0'
     SimpleDateFormat formatter = new SimpleDateFormat ("MMM dd, yyyy");
     Date strDate12 = new Date(strDate);
     String strExpDate = "";
     try
          strExpDate = formatter.format(strDate12);
          out.println("Formatted Date is :" + strExpDate); // in windows I got correct
result as 'Jul 07, 2003' and in UNIX java.lang.IllegalArgumentException
     catch(Exception e) {}
%>
</es:forEachInArray>
Any help will be much appreciated.
thanks
-Amar Purumandla

hi,
I have one Date attribute called 'EXPIRATION_DATE' in DOCUMENT table.
I mapped this column entry in 'application-config.xml' as jdbc.column.EXPIRATION_DATE=ExpirationDate;
And when I am trying to get this value in JSP,within '<es:forEachInArray>' tag
scope, using the syntax below
<%
String strDate = (String)doc.getProperty("LodedDate","ExpirationDate");
%>
I am getting different formatted results in different environments
Like , when I executed this in windows ,
I got the resulted string as "Mon Jul 07 00:00:00 EDT 2003" , which can be converted
to 'Date' type
using <% Date exp_date = new Date(strDate); %> which solves my problem.
But , when I executed same code to UNIX ,
I got the resulted string as "2009-02-01 00:00:00.0" , which is not convertible
to 'Date' format.
I got the following exception , when I try to convert this resulted String to
date format like.
<% Date exp_date = new Date(strDate); %>
java.lang.IllegalArgumentException
at java.util.Date.parse(Date.java:585)
at java.util.Date.<init>(Date.java:267)
Finally , I need to convert the resulted string to "MMM dd, yyyy" (Feb 22, 2000)format.
If not above method , what is the best way to get the resulted value in this "MMM
dd, yyyy" format.
/***** My Sample code ********/
<es:forEachInArray array="<%=BankerMsgs%>" id="doc" type="Content" >
<%String strDate = "";
     strDate = (String)doc.getProperty("LodedDate","ExpirationDate");     //strDate =
"Mon Jul 07 00:00:00 EDT 2003"; // Windows
     //strDate = "2003-07-07 00:00:00.0"; // UNIX
     out.println("Original Date is :" + strDate); // In windows env I got this formatted
result 'Mon Jul 07 00:00:00 EDT 2003' and In UNIX I got the string as '2003-07-07
00:00:00.0'
     SimpleDateFormat formatter = new SimpleDateFormat ("MMM dd, yyyy");
     Date strDate12 = new Date(strDate);
     String strExpDate = "";
     try
          strExpDate = formatter.format(strDate12);
          out.println("Formatted Date is :" + strExpDate); // in windows I got correct
result as 'Jul 07, 2003' and in UNIX java.lang.IllegalArgumentException
     catch(Exception e) {}
%>
</es:forEachInArray>
Any help will be much appreciated.
thanks
-Amar Purumandla

Need help applying formatting in GREP search

I'm trying to work out how I can apply character formatting to a specific character within a pattern rather than applying the character style to the whole pattern.
I can create a search which returns the text string that contains the particular character I want to format, but I want to apply a character style to a single character within that string. For instance:
The text I am searching for might be 7b9. I want to be able to apply a character style to just the "b" and not the 7 or 9. Obviously I can't apply the formatting to all instances of "b"...
Is that possible?
Thanks for any help. I'm on v5.5.

Sure
(?<=\d)b(?=\d)
Should do it.
If you need it to be any letter inbetween then try
(?<=\d)\w+?(?=\d)
If you have any other complex examples let me know

Need help Playing/Formatting videos!!

I have several music videos saved as Quick Time files, but my iPod is not recognizing them, or downloading them? any suggestions???

Do you have a Video iPod and if you do you need to
convert all your video to a format that your iPod
understands. I believe that the tool you need is
built right into iTunes 6.0.3
Thanks for the replies...I do have the new video ipod. Is the tool that you are referring to the "convert to AAC" option? I've tried it....but keep gettin some -50 error message? ( I am using 6.0.3 by the way) thanks again for the help.

Need Help in Formatting Spool data

Hi,
Can anyone of you let me knw how to obtain the output flat file in the below format ?
"ID"|"NAME"|"PARENT_ID"
"NQ TEL"|"14"|"Macetown"
But I am gettin the output.. as below.
VENDOR_NAME||'|'||VENDOR_ID||'|'||CITY
NQ TEL|14|Macetown
NA TEL|14|Molokai
I am using the following script in SQL PLUS and calling it with @ < file path>.
set heading on
set echo off
set feedback off
spool Y:\Spool\output1.txt
select Vendor_Name || '|' || Vendor_ID || '|' || City from vendor where city like 'Ma%';
spool off;
set feedback on
set echo on
set heading on
Can anyone help me on this.? In Addition to this, I also need to remove the line separating Header and the Data .
Thanks a ton. :)

Try this:
select ' " ' || Vendor_Name || ' " ' || ' "|" ' from vendor where city like 'Ma%';

Need help to format data

Hi Gurus,
I am extracting the field "CATEGORY" from oracle to BW. But I found data in the InfoCube is in exponential format (Example Cateory = 4.1030000000000000E+03 ). I don't need data in exponential format. What's the best way to fix this problem.
Thanks
Liza

Hi,
Check the downloaded file from Oracle. I guess, you opened up in Excel and then loaded into BW.
Open it in Notepad and suppose you are creating .csv file, then open it as text file in the Excel.
Hope, it helps.
Thanks
Viswa

Need help to format the output of the query.

First of all i would like to say I m newbi in oracle query
and of course thanks to read the thread.
I have a problem formatting a query output.
Actually the query is like the following :
select a1
,b1
,c1
from table
where id.table=1
UNION
select a2
,b2
,c2
from table2
where id.table2=1
order by 1;
exit;
my actual output
a1 b1 c1
a2 b2 c2
a1 b1 c1
a2 b2 c2
my desired output
a1 b1 c1
a2 b2 c2
a1 b1 c1
a2 b2 c2
So what i need is an empy row between the groups of results
and to shift the union query.
thanks in advance

SQL>select * from t1;
        C1         C2         C3
         1          2          3
         2          3          4
         3          4          5
SQL>select * from t2;
        C1         C2         C3
        30         40         50
        20         30         40
        10         20         30
SQL>select c1,c2,c3
2 from( select c1,c2,c3,1 flg
3           from t1
4           union all
5           select c1,c2,c3,2
6           from t2
7           union all
8           select null,null,null,1
9           from dual)
10 order by flg,c1,c2,c3 nulls last;
        C1         C2         C3
         1          2          3
         2          3          4
         3          4          5
<br>
        10         20         30
        20         30         40
        30         40         50
7 rows selected.
Funny.......

Need help f8 format

Similar Messages

Maybe you are looking for