Need OID for rxload and input rate

Hi all,
I want to monitor the rxload and input rate on interfaces but I can't find the correct OID can someone help me with this please.
Can someone also provideme a good document for this
GigabitEthernet4/8 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet Port, address is 000d.657d.3387 (bia 000d.657d.3387)
Description: --- 2924_MAIN ---
MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,
     reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, link type is auto, media type is 10/100/1000-TX
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:47, output never, output hang never
Last clearing of "show interface" counters 20w1d
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 5000 bits/sec, 4 packets/sec
5 minute output rate 153000 bits/sec, 26 packets/sec
     143271178 packets input, 34567505950 bytes, 0 no buffer
     Received 2731549 broadcasts (295416 multicast)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     253476590 packets output, 117220536494 bytes, 0 underruns
     1341644 output errors, 542074 collisions, 0 interface resets
     0 babbles, 259071 late collision, 0 deferred
     0 lost carrier, 0 no carrier
     0 output buffer failures, 0 output buffers swapped out

Hi,
     I haven't been able to find any documentation on CCo regarding this, but in my searching, I have come across the following MIb Object, which will tell you the input rate on the interface :
.1.3.6.1.4.1.9.2.2.1.1.6
locIfInBitsSec OBJECT-TYPE
    -- FROM     OLD-CISCO-INTERFACES-MIB
    SYNTAX          Integer
    MAX-ACCESS     read-only
    STATUS          Mandatory
    DESCRIPTION    "Five minute exponentially-decayed moving                            average of input bits per second."
     There is a similar object locIfOutBitsSec (.1.3.6.1.4.1.9.2.2.1.1.8) for the output rate.
     To so rxload = 255 * locIfInBitsSec / (1000000 * ifHighSpeed )
Regards
Derek

Similar Messages

OID for CPU and MEMORY utilization for wrv4400n

Hi,
Can any one please tell me the OID for CPU and MEMORY utilization for wrv4400n?
Thanks
Vipin

CISCO-SYSTEM-EXT-MIB.my is a good place to start and you can determine the OID from the MIB.
Once you feel as though you are on the right track, have a look at:
http://www.oidview.com/mibs/9/CISCO-SYSTEM-EXT-MIB.html
I gather that what you need is:
1.3.6.1.4.1.9.9.305.1.1.1
and
1.3.6.1.4.1.9.9.305.1.1.2
Enjoy.
Stephen

Infoobjects for currencies and exchange rates related data

Hi Experts,
Please tell me standard Infoobjects for currencies and exchange rates related data that have been made available for third party tools?
Any useful answer will be rewarded with suitable points.
Thanks!

Rohan
Use 0currency - for currency
0unit for unit of measures
Arun

I created an account but haven't yet purchase any products yet! I'm a publisher launching a magazine so i need something for design and making a layout for magazine! Please help is there a number i can talk to someone ?

created an account but haven't yet purchase any products yet! I'm a publisher launching a magazine so i need something for design and making a layout for magazine! Please help is there a number i can talk to someone ?

Adobe Connect Support phone numbers
or
Cloud Plans https://www.adobe.com/products/creativecloud/buying-guide.html

SNMP OID for 5108 Chassis input and output Watts?

Anybody know these?
Craig

Craig,
OID for cucsEquipmentChassisStatsTable -- 1.3.6.1.4.1.9.9.719.1.15.10
UCS MIBs are available here
ftp://ftp.cisco.com/pub/mibs/supportlists/ucs/ucs-manager-supportlist.html
HTH
Padma

SNMP OID for CPU and Memory Utilization on a MDS 9509

Does anyone know what the OIDs are for CPU and Memory utilization on a MDS 9509?
Thanks

CISCO-SYSTEM-EXT-MIB.my is a good place to start and you can determine the OID from the MIB.
Once you feel as though you are on the right track, have a look at:
http://www.oidview.com/mibs/9/CISCO-SYSTEM-EXT-MIB.html
I gather that what you need is:
1.3.6.1.4.1.9.9.305.1.1.1
and
1.3.6.1.4.1.9.9.305.1.1.2
Enjoy.
Stephen

PLEASE: How can I save my iphone texts and "notes" (not "the note") to my computer? I need them for reference and legal purposes. I have yet to find an app for this and iphone doesn't sync either one.

Greetings!
I am brand new to using a Support Community -- I'm more of a in-person show me learner but...huge snowstorm and I don't want to
to make an appointment at a Genius Bar, driving 15 miles, especially since I asked about this once before and no one there was able to
give me an "official" Apple answer . I do hope I am posting my question (and plea) for help properly.
LOL when I had my first lil' Mac Classic, over 20 years ago, my participation in the techno world was soooo much easier, simpler.
My current situation: I have soooo many texts on my iphone and I haven't deleted many because I need the information contained in them for
future reference and for legal purposes. I would really like to find a means and way to save them other than on the phone itself.
I've done searches for various apps yet I'm not finding what I think I would need. It appears Apple does not sync the texts between the iphone and
my MacBook Pro.
Also I often use Notes for quick journaling as well as copy and pasting from other apps, usually inspirational, that I know I am going to want
to read again (always with credit noted ) and these too are taking up space. If I could email myself I would but the apps I'm using don't offer that and each day there is a new commentary -- no way to go "back".
I am currently using OS 10.6.8 on my MacBook -- my disc drive doesn't work and upgrading has to be done at the Apple Store so I don't have iCloud yet.
My iphone 4 is running OS 6.0.1 -- no upgrade until I'm at a wifi connection -- most of the time I'm using my personal hotspot.
I'm a very busy self-employed Nana raising grandchildren and a great-grandchild. I don't have a lot of time and certainly not enough for copying and pasting every text as well as note and emailing it to myself. There has got to be a better, easier way, yes?
I'd be most appreciative of any and all assistance here. Oh, someone mentioned to me I ought to get a "stick" for downloading but were talking
in a language I'm still learning.
Thank you!
Melinda

SkyDaughter29 wrote:
My current situation: I have soooo many texts on my iphone and I haven't deleted many because I need the information contained in them for future reference and for legal purposes. I would really like to find a means and way to save them other than on the phone itself. I've done searches for various apps yet I'm not finding what I think I would need. It appears Apple does not sync the texts between the iphone and my MacBook Pro.
Try the computer apps PhoneView (Mac) or TouchCopy (Mac & PC):
http://www.ecamm.com/mac/phoneview/
http://www.wideanglesoftware.com/touchcopy/index.php
Best of luck.

Need table for customer and vendor carry forward balance

Hi,
I need to fetch the carry forward(opening) balance for GL, customer and vendor account for my report.
I have table which contains c/f balance for GL accounts which is "GLT0" and now looking for a table for customer and vendor accounts.
Please let me know if anyone have idea in which table i can get the c/f balance for customer and vendor accounts.
Thanks in advance.
Regards,
Swati

Hi Gurus
The requirement from the client side in my case is to have opening balance in Tr code ZFBL1n, ZFBL3N and ZFBL5N.
Now, from the above thread i got the Tables where i could find the Vendor and Customer Opening Balance but i also want Opening Balance for GL.
and my 2nd query is how to get these opening balance in Z report, at Header Level.
Thanks and Regards
Dnyanesh

Need Ideas for creating and using Custom Business Object

Hello Guys,
I am developing an application which uses a Request->Approve->Create approach for creating Purchase documents.
Now I am a little puzzled about how to make use of the Business Object BUS2014.
The application I am developing has its own unique 'Request Number' (say REQID) which will point to the Request for Creation of a purchase order.
Whenever a Request is created (from a Z-Tcode) a workflow needs to be initiated and it has to be sent to the approver.
The Purchase Document will be created once the approver approves.
Now my confusion here is, if I use BUS2014, the object will be instantiated only during the final step of the workflow. But I need an instance during the beginning of the Requestor ->Approver negotiations as I am playing with events. These events needs an Object_key.
How should I proceed here?
Should I create a new logical Business Object like ZPOREQ where I have the above mentioned REQID as the key?
And should I have an attribute of type BUS2014 inside the custom BO?
How will I make use of the methods like BUS2014.Create etc which I may need to create the purchase document?
Any small direction will be a huge help for me to get used to this wilderness.

Hi,
You should continue with the ABAP class idea. The business objects are kind of "obsolete" already, and if there is a need to create a new "object", ABAP classes are the way to go. Business objects are still useful, but I normally use them only when an existing standard business object fulfills the requirements (possibly with slight additions) which is almost never.
From my point of view you can use the existing class. Depending on the circumstances I normally have just one class that I use for both workflow and the possible other functionality that is required, but you have to understand that I have this goal in my mind already when starting the development process. As your class most probably has many useful features already (such as you have the header and item data as attributes etc. (if I understood correctly?), these are also useful in in workflow (class attributes will be available in WF container etc.).
If you are hesitant to use the same class directly in your workflow, you could also create a new class ZCL_REQUEST_FOR_WF (with the workflow interface), and then simply add your existing class ZCL_WF_REQUEST as an attribute to this new class. Then this new workflow class could include the pure workflow stuff, and your existing class the non-workflow stuff. But this most probably will not make much sense - just implement the if_workflow interface in your existing class (this is just one possibility that you might consider.)
Regards,
Karri

Bootcamp: Two keyboards needed -- one for Windows and one for Mac?

Oh, the ground-pounding frustration! I bought the Apple wireless (Bluetooth) keyboard with my new dual-core Intel iMac, and was told it would work in both Windows and Mac worlds. Not so! It works fine with Apple OS, but not with Windows XP. Frustratingly, the wireless mighty-mouse works (after you left-click), but the keyboard won't work. Sometimes it will work if I turn it on and off a few times. And yes, I have activated the bluetooth finder in "control panel" under the Windows OS, and yes, both are recognized and "connected." (So is an HP printer which works well, albeit slowly.) I had to buy a Microsoft wired USB keyboard to get through the Windows setup. Curiously, this Microsoft wired keyboard works with both the Windows and Mac OS.
I have another issue, also, but perhaps it would best if I posted it separately. Still, if anyone can tell me why this computer cannot come out of "standby" in Windows without hanging up (weird colors on screen, half-brightness in screen, locked mouse and keyboard), I'd appreciate it very much.
Please reply to: [email protected]
And thank you very much indeed for any insight you can provide. Maybe I should just go buy the wired Apple keyboard and mouse?
20" iMac Intel dual core Running Bootcamp

Sorry, but here's the work from the BootCamp Requirements/FAQ page (emphasis mine):
"Are there any Macintosh features that I should not expect to work when running Windows XP on an Intel-based Macintosh computer?
Even after installling the Macintosh Drivers CD, the Apple Remote Control (IR), Apple Wireless (Bluetooth) keyboard or mouse, Apple USB Modem, MacBook Pro's sudden motion sensor, and MacBook Pro's ambient light sensor will not function correctly when running Windows."
So it does indeed look like you'll need a wired keyboard and mouse, at least for now (we'll have to see what's supported when Leopard comes out).

Is there a single snmp oid for flash and dram ?

Does a single univeral oid (or 1 for flash and one for dram) exist that will provide total amount of flash and total amount of dram across all chassis families ?
Thanks

This link is your best bet:
http://www.cisco.com/warp/public/477/SNMP/contiguous_memory.html

Need help for Update and cancel SalesOrder

Hi All,
I written java code for create sales order based on salesquotation,now i want to update and cancel sales order ,i need help to update and cancel salesorder.
can give any related links for update and cancel salesorder.
Thanks and Regards,
Srinivas

Hi srinivas.L
It is simple, here is some sample code. You must use getbykey to get the document. Then once you got it you can make whatever changes you need. Then update it. where i have oOrder.Update() you can have oOrder.cancel
Dim oOrder As SAPbobsCOM.Documents
        oOrder = oCompany.GetBusinessObject(SAPbobsCOM.BoObjectTypes.oOrders)
        If oOrder.GetByKey(530) Then
            oOrder.Lines.SetCurrentLine(1)
            oOrder.Lines.WarehouseCode = "01"
            If oOrder.Update() <> 0 Then
                MsgBox(oCompany.GetLastErrorDescription)
            End If
        Else
            MsgBox("Nothing found")
        End If
Hope this helps

I need help for cloud and ios5

Help me for cloud and ios5

Sounds like I have a similar problem. I just updated iPad, and iPhone to iOS5. I synced these devices with my iMac on iCloud. Calendars and contacts synced just fine. However for some strange reason I can no longer sync any music on my 32 GB iPhone. iTunes is telling me that I am beyond the phone's capacity with an "Other" item that is nearly as large as my music collection. Am I missing something here? Your help will be greatly appreciated.

I need help for install and configure password sync from AD to OID

Hi guys!
I need to sync passwords from AD to OID, first all, ¿What software do I need? I read some docs and don't find the good config.
I'm trying with:
-Database 11g
-Weblogic 11g
-SOA 11g
-IDM 11g
-IAM 11g
First I install the Database and load the schemas with RCU, next install Weblogic without domian, next install SOA, next install IDM (OID and DIP) in a new Weblogic Domain, next install IAM, next configure IAM in the domain created before, next configure SSL, check the config by using ldapbind, next configure DIP.
It's that ok?
¿What I am doing wrong?
Thank you all.

If all you need is AD & OID then OIM is not required. DIP alone can handle this
Password sync should work using DIP. if this is not working then check synchronization mapping and verify that password attribute is also part of this AD-OID sync. Enable debug in synchronization profile or raise an Service Request with Oracle support.
Check
http://docs.oracle.com/cd/E23943_01/oid.1111/e10031/odip_actdir.htm#CHDIGDEH
and
http://docs.oracle.com/cd/E23943_01/oid.1111/e10031/odip_config_integration.htm#BABBFAAJ
and
http://docs.oracle.com/cd/E23943_01/oid.1111/e10031/odip_adpasswordsync.htm#CHDBIIJC
Atul Kumar

Need help for ACL and NAT

Hi all
I setup a router 2911 with the configuration below for the phone system inside handle all calls in and out from and to the outside provider VoIP.
I can receive the calls from outside all time but I cannot make the call from the inside to outside.
I think that I miss some configuration in router.
The 172.a.b.c is the IP phone system.
Please give me any advice
Thanks a lot.
The router configuration:
interface Embedded-Service-Engine0/0
no ip address
interface GigabitEthernet0/0
description internal-LAN
ip address 172.x.x.4 255.255.x.x
ip accounting output-packets
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.1
encapsulation dot1Q 11
ip address 172.16.208.1 255.255.240.0
interface GigabitEthernet0/2
description internet
ip address 50.x.x.93 255.255.x.240
ip accounting output-packets
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 100 interface GigabitEthernet0/2 overload
ip nat inside source static udp 172.a.b.c 5060 50.x.x.93 5060 extendable
ip route profile
ip route 0.0.0.0 0.0.0.0 50.240.226.94
ip route 172.16.240.0 255.255.254.0 172.10.0.5
ip route 172.16.242.0 255.255.254.0 172.10.0.5
ip access-list extended VLAN-voice
access-list 100 permit ip 172.x.0.0 0.0.255.255 any
access-list 100 permit ip 172.16.240.0 0.0.0.255 any
access-list 100 permit ip 172.16.242.0 0.0.0.255 any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login
transport input all
scheduler allocate 20000 1000
end

You really don't want to use NAT with SIP. Odds are it won't work. This is because SIP embeds hostnames/IP Addresses inside the packets, and standard NAT does not look inside packets.
If you want a NAT-type functionality for SIP, you need something called a session border controller. Look up Cisco CUBE
http://www.cisco.com/c/en/us/products/unified-communications/unified-border-element/index.html
https://supportforums.cisco.com/docs/DOC-17964
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-border-element/99863-cube-config.html
GTG
Please rate all helpful posts.

Need OID for rxload and input rate

Similar Messages

Maybe you are looking for