Need to get internet working on X3 00

HEY
I need to know what are the settings to get internet working with my Nokia X3 00, I have AT&t services. Please help

I got my X3 working with AT&T Prepaid plan (which is really expensive). I'm not 100% sure of all these steps are necessary due to tinkering around, but at least I'm online.
Settings -> Connectivity -> Packet data -> Packet data settings -> Packet data acc. pt.
Set this to: wap.cingular
Settings -> Configuration -> Personal config. sett. -> Add new -> Access point -> Access point settings -> Bearer settings
Packet data acc. pt. -> wap.cingular
If that doesn't work, I tinkered with the settings from this site: http://www.howardforums.com/printthread.php?t=1630604
HTH,
-will

Similar Messages

Do i need to get internet service with an internet provider?

Do i need to get internet service with an internet provider to use airport extreme or airport express?

Well, either that, or you could simply use your extreme or express to "borrow" your neighbour's WEP encrypted WiFi network..
OH wait.. I think I got you. Are you asking if you can use the bases for just a Lan and no outside connection? You can use them without the internet. It's just an option.

I have an airport express (802.11n) which download do I need to get it work on Windows 8.1?

I have an airport express (802.11n) which download do I need to get it work on Windows 8.1?

That one doesn't work.
Verstuurd vanaf mijn iPhone
Op 19 nov. 2014 om 13:55 heeft "Apple Support Communities Updates" <[email protected]<mailto:[email protected]>> het volgende geschreven:
http://www.apple.com/support/assets/images/external/emails/logo.gif
You received a reply
Bob Timmons<https://discussions.apple.com/people/Bob+Timmons?ac_cid=op123456> has replied to your question. You can view the full discussion<https://discussions.apple.com/message/27128939?ac_cid=op123456#27128939> in Apple Support Communities.
I have an airport express (802.11n) which download do I need to get it work on Windows 8.1?<https://discussions.apple.com/message/27128939?ac_cid=op123456#27128939>
It has been some time since Apple updated AirPort Utility for Windows. The current version is 5.6.1.
It runs on Windows 7, but I have not checked on Windows 8.
AirPort Utility 5.6.1 for Windows<http://support.apple.com/kb/dl1547>
Correct Answer <https://discussions.apple.com/email/thread/6679920/correct/27128939> Helpful Answer <https://discussions.apple.com/email/thread/6679920/helpful/27128939>
Use the buttons above to tell Bob Timmons and the rest of the community if this reply solved your question or helped you get closer to finding a solution.
To reply to Bob Timmons, go to the discussion<https://discussions.apple.com/message/27128939?ac_cid=op123456#27128939> in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile<https://discussions.apple.com/user-preferences!input.jspa>.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved<http://www.apple.com/legal/> | Privacy Policy<http://www.apple.com/legal/privacy/> | Terms of Use<https://discussions.apple.com/docs/DOC-5952> | Apple Support<http://www.apple.com/support/>

How to get internet working?

I bought a blackberry curve 8530 on pay as you go, and I can use my home wi-fi fine but I am wondering, how can i get internet to work anywhere?
Thanks

As long as that is The BlackBerry Data Plan, yes. You might need to give it a few hours to get provisioned to your device, and it will.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

My 7th gen ipod nano wil not show up on my laptop when I plug it in and neither will my brothers new ipad,they don't come up in my computher either and I've installed the new itunes twice but still no change,I really need to get this working,Please help

I need help

Thanks for a reply
The cable that I'm using came with my 5th gen nano. The 6th gen Ipod shows that it's connected but the computer doesn't see it, so I don't think that it's the cable.
I did try this before when looking at the troubleshooting guide and nothing happens. It just resets and then the Ipod screen tells me that it's connected to the computer. It still is unseen by Itunes and no where to be found in my computer.
I don't have another computer to plug it into at the moment but I may be able to visit a friend that owns a decent PC in a few days. If that doesn't work out I will be getting a new lap top in a week and I'm hoping that it will work on that, but it won't be a Mac. So, let's say it works when I plug it into one of these computers, should I reset my Ipod from there or is there something else I should do?

Help needed in getting applet working

import java.awt.*;
import javax.swing.*;
import java.awt.event.*;
public class murali1 extends JApplet{
     private Container contain;
     private GridBagLayout grid;
     private GridBagConstraints c;
* Create the GUI and show it.
public murali1() {
          //super("Assignment 1");
//Create and set up the window.
JFrame frame = new JFrame("Assignment 1");
          //Menu
          JMenuBar bar = new JMenuBar();
          JMenu file = new JMenu("File");
          bar.add(file);
          JMenuItem open = new JMenuItem("Open");
          file.add(open);
          open.addActionListener(new ActionListener(){
          public void actionPerformed (ActionEvent e)
          JMenuItem save = new JMenuItem("Save Random");
          file.add(save);
          save.addActionListener(new ActionListener(){
          public void actionPerformed (ActionEvent e)
          JMenuItem exit1 = new JMenuItem("Exit");
          file.add(exit1);
          exit1.addActionListener(new ActionListener(){
          public void actionPerformed (ActionEvent e)
               System.exit(0);
          //Create 4 panels
          JPanel panel1,panel2,panel3,panel4;
          /*Adding components to Panel 1
          Panel 1 contains one Label and a ComboBox
          Panel 1 is a GridLayout
          panel1=new JPanel();
          String method[] = {"Random","Ascending","Descending"};
          JComboBox combo = new JComboBox(method);//Combo Box
          combo.setMaximumRowCount(3);
          combo.addItemListener(new ItemListener(){
          public void itemStateChanged(ItemEvent comboevent)
          JLabel combolabel;
          combolabel = new JLabel("Choose Prioritization Heuristic");
          //panel1.setLayout( new GridLayout (2,1));
          panel1.add(combolabel);
          panel1.add(combo);
          /*Adding components to panel 2
          Panel 2 contains one label and one text area
          Panel 2 is a GridLayout
          panel2 = new JPanel();
          JLabel textlabel = new JLabel("Evaluator Results");
          JTextArea evalarea = new JTextArea();
          panel2.add(textlabel);
          //panel1.setLayout( new GridLayout (2,1));
          panel2.add(evalarea);
          /*Adding components to panel 3
          Panel 3 contains 5 labels,3 textfields, 1 button
          Panel 3 is a GridLayout
          panel3 = new JPanel();
          JLabel label1,label2,label3,label4,label5;
          label1 = new JLabel("Use the Fields only for Random Heuristic");
          label2 = new JLabel("Enter Maximum # of Tries");
          label3 = new JLabel("Enter # of Tests in TS");
          label4 = new JLabel("Enter ID# of Tests in TS(d) (Separated by Comma)");
          label5 = new JLabel("Please Press SUBMIT");
          JTextField tf1,tf2,tf3;
          tf1 = new JTextField();
          tf2 = new JTextField();
          tf3 = new JTextField();
          JButton submit = new JButton("Submit");
          //panel1.setLayout( new GridLayout (9,1));
          panel3.add(label1);
          panel3.add(label2);
          panel3.add(tf1);
          panel3.add(label3);
          panel3.add(tf2);
          panel3.add(label4);
          panel3.add(tf3);
          panel3.add(label5);
          panel3.add(submit);
          /*Adding components to panel 4
          Panel 4 contains 4 labels,1 textfields, 3 button
          Panel 4 is a GridLayout
          panel4 = new JPanel();
          JLabel label6,label7,label8,label9;
          label6 = new JLabel("Press RUN to start evaluation");
          label7 = new JLabel("Press Exit to Terminate Program");
          label8 = new JLabel("MLP(d) and RP(d) are:");
          label9 = new JLabel("Press CLEAR to start new evaluation");
          JButton run = new JButton("Run");
          JButton exit = new JButton("Exit");
          JButton clear = new JButton("Clear");
          JTextArea area1 = new JTextArea();
          panel4.add(label6);
          panel4.add(run);
          panel4.add(label7);
          panel4.add(exit);
          panel4.add(label8);
          panel4.add(area1);
          panel4.add(label9);
          panel4.add(clear);
          /*panel1.setVisible(true);
          panel2.setVisible(true);
          panel3.setVisible(true);
          panel4.setVisible(true);*/
          /* set Grid Bag Layout
          Add all the panels to the GridBag Layout
          contain = frame.getContentPane();
          grid = new GridBagLayout();
          contain.setLayout(new GridBagLayout());
          c = new GridBagConstraints();
          addComponent(panel1,0,0);
          addComponent(panel2,0,4);
          addComponent(panel3,4,0);
          addComponent(panel4,4,6);
          //setSize(1200,100);
          this.setVisible(true);
          /*Method to Add Components*/
          private void addComponent(Component co,int row,int column)
                    c.gridx = column;
                    c.gridy = row;
                    grid.setConstraints(co,c);
                    contain.add(co);
/*Set up the content pane.
addComponentsToPane(frame.getContentPane());*/
//Display the window.
//frame.pack();
//frame.setVisible(true);
public static void main(String[] args) {
murali1 g = new murali1();
               //g.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);
The Compliation is totally fine,applet loads, but the gui components are not diaplyed.Any suggestions.
Thank you.

That's not really an applet. Or it's a half-done one. It looks like you just took a standalone app (with its own frame and everything), added "extends JApplet", commented out a few things that absolutely shouldn't work, and otherwise changed almost nothing.
The browser won't invoke the applet's main() method. I guess that's not a problem, but are you aware that it's not being invoked?
An applet is a kind of panel. You shouldn't be creating frames. You should put all the GUI elments in the panel...which it appears you did, but can you actually get rid of the irrelevant code? Furthermore, when you post code on these forums, you should wrap it in [code][/code] tags; it makes it much easier to read.
An applet shouldn't call System.exit(). You'll probably get a security exception if you try running that.
That addComponent method looks suspicious to me. You're changing the columns and row of the same object over and over again. I'm not a GUI expert, so maybe I'm wrong, but that seems really wrong.
You shouldn't need to call this.setVisible(true) for an applet.
I'd suggest cleaning your code up, and maybe moving some of that stuff out of the constructor anyway. In an applet it might be better placed in init().
Message was edited by:
paulcw

Can't get Internet working on ASA 5525X

Hello
i have a ASA 5525x
im in testing proccess and cant make internet routing working
im routing between 2 private ip cuz outside interface is connected to the lab switch.
im able to ping anything from ASDM als i tried packet tracer using the ip that assigned to the end-user and it is working fro asa but not on the win7 machine .
after enabing logging on asa i got asa teardown the icmp connection (when trying to ping 8.8.8.8)
any ideas why ?
ASA Version 9.0(2)
hostname MIKUNI-LA-ASA1
enable password nsi9HaIu8epX9MzI encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0/0
nameif outside
security-level 0
ip address 172.30.200.100 255.255.255.0
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 10.10.10.1 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/6
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/7
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
banner motd
banner motd !!!!!!!!!!!!!!!DO NOT LOGON!!!!!!!!!!!!!!!
boot system disk0:/asa902-smp-k8.bin
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 8.8.8.8
same-security-traffic permit intra-interface
object network internet
host 172.30.200.100
pager lines 24
logging enable
logging trap errors
logging asdm informational
mtu management 1500
mtu inside 1500
mtu outside 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-712-102.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,inside) source dynamic any interface dns
route outside 0.0.0.0 0.0.0.0 172.30.200.1 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
sysopt noproxyarp inside
sysopt noproxyarp outside
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption rc4-sha1
username admin password y9JC1OmYlTqCYCh5 encrypted privilege 15
username neocomp password zEZJ79.tgPiYxCsz encrypted privilege 15
class-map inside-class
match default-inspection-traffic
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
policy-map inside-policy
class inside-class
inspect dns
inspect ftp
inspect h323 h225
inspect h323 ras
inspect http
inspect icmp
inspect ip-options
inspect ipsec-pass-thru
service-policy global_policy global
service-policy inside-policy interface inside
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:e8f3db05e9bce814811bac225d27ded8
: end

didnt work
Itried clean configuration but its still same thing cant get to the internet thru firewall
from asa i can ping everything but from end-user side it show DNS is not responding and i can not ping the outside interface on ASA
ASA Version 9.0(2)
hostname MIKUNI-LA-ASA2
enable password 8Ry2YjIyt7RRXU24 encrypted
xlate per-session deny tcp any4 any4
xlate per-session deny tcp any4 any6
xlate per-session deny tcp any6 any4
xlate per-session deny tcp any6 any6
xlate per-session deny udp any4 any4 eq domain
xlate per-session deny udp any4 any6 eq domain
xlate per-session deny udp any6 any4 eq domain
xlate per-session deny udp any6 any6 eq domain
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface GigabitEthernet0/0
nameif OUTSIDE
security-level 0
ip address dhcp setroute
interface GigabitEthernet0/1
nameif INSIDE
security-level 100
ip address 192.168.100.1 255.255.255.0
interface GigabitEthernet0/2
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/3
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/6
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/7
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
banner motd !!!!!!!!!!!!!!!DO NOT LOGON!!!!!!!!!!!!!!!
boot system disk0:/asa902-smp-k8.bin
ftp mode passive
dns domain-lookup OUTSIDE
dns domain-lookup INSIDE
dns server-group DefaultDNS
name-server 8.8.8.8
object network Internet
subnet 192.168.100.0 255.255.255.0
pager lines 24
logging enable
logging console warnings
logging asdm informational
mtu management 1500
mtu OUTSIDE 1500
mtu INSIDE 1500
no failover
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-712-102.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
object network Internet
nat (any,OUTSIDE) dynamic interface dns
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication ssh console LOCAL
http server enable
http 192.168.1.0 255.255.255.0 management
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec security-association pmtu-aging infinite
crypto ca trustpool policy
telnet timeout 5
ssh timeout 5
console timeout 0
dhcp-client client-id interface OUTSIDE
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
ssl encryption rc4-sha1
username admin password y9JC1OmYlTqCYCh5 encrypted privilege 15
username neocomp password zEZJ79.tgPiYxCsz encrypted privilege 15
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:8659ad01179820e90e68d3725961dc2c

Need to get available working day

Hi All,
I'm using oracle 9i version.
i have a procedure which will take 1 in parameter and 1 out parameter.
we will pass one inputdate
now the date which i passed is sunday or holiday then we have to return the next working day that holiday list i'm getting form holiday_list table.
now the problem is suppose i passed a date which is sunday so now i have to return like the inputdate+1 so that it will be monday . but now i need to check weather that monday also holiday or not in the holiday list
if it is then i have to go for next like INputdate+2 again there also i have to check the same for this till i get a available date .
can some suggest how to handle this problem.
Thanks in advance
-RG

SQL> select * from holidays;
DT
01-JUL-07
11-JUL-07
02-JUL-07
07-JUL-07
SQL> exec :your_date := '07-jul-2007';
PL/SQL procedure successfully completed.
SQL> select min(dt) dt
2   from(
3     select trunc(to_date(:your_date,'dd/mm/yyyy')) + level - 1 dt
4     from (select case when count(*) <= 8 then 9 else count(*) end cnt
5         from holidays
6         where dt >= trunc(to_date(:your_date,'dd/mm/yyyy')))
7     connect by level <= cnt
8     )
9   where to_char(dt,'fmday') != 'sunday'
10   and dt not in(select dt
11                 from holidays
12                 where dt >= trunc(to_date(:your_date,'dd/mm/yyyy')))
13   /
DT
09-JUL-07
Message was edited by:
        jeneesh
curved path......

Need Help getting games working...

So I am having trouble getting basically any games working correctly on my arch setup. This wouldn't really bother me but my gf likes playing them and I had a few working when I was using Bodhi Linux so she now thinks that Arch is not as good as Bodhi lol.
Please help me either get one of the games I have working or find some that will work.
Right now, the games I have been trying and problems I'm having with each are as follows:
Supertux: Really slow; I had this working on Bodhi
DJL: Not really a game but this is what I used to use to get games; I found in AUR but it hasn't been updated for awhile; When I try to run it I get the following error (although I think it is generic msg):
File "/usr/share/djl/djl/config.py", line 212, in config
loc = locale.getdefaultlocale()[0].split("_")[0]
AttributeError: 'NoneType' object has no attribute 'split'
bsnes: All the ROMs I find are .smc format and bsnes will only work with .sfc
Anyone have any ideas on how to get any of these working? It would be greatly appreciated. I love Arch so much more than any other distro I've tried because I can set it up exactly how I want and it runs so efficiently on my older computer but if I can't get some games working I'm going to be nagged to switch back to Bodhi.
The other option is to dump the gf lol, but its a tough decidion between Arch and her .
~Boz~

Yeah, I know it definitely doesn't have 3D acceleration bc when I was running Linux Mint I would automatically be put into "Fallback mode" as the MGSE req'd 3d acceleration. What I don't get is how I had the games working while running Bodhi.
It might have been something in Djl that helped tweak the configuration and allow games to work because that was where I was using the games that I did. I just had assumed that using Super Tux w/o Djl would be the same. I do think that Djl not working has something to do with it needing Python 2 but I have tried and can't figure out how to force it to use only that. Not sure if that is bc it is hard to or just bc I don't know how .
I did try to install Zsnes but got an error during the build. I tried the 'zsnes-netplay' version bc it had been updated more recently (although still almost a year ago). I'll give the other version a try today to see if it makes any difference.
Going to leave this as unsolved until after I try that so if anyone else has any suggestions, please feel free. If no progress by EOD, I will mark as solved and take it that the fact that I don't have 3d acceleration is the cause of my problems. As I mentioned at the beginning, I really could care less about the games. Just was trying to keep the gf happy but not always possible .
Thanks again,
~Boz~

How to get internet working when it is already connected

my iphone is new and i used the wifi about three weeks ago on it and it was working all fine. i went oversea's and turned it off and when i turned it back no i turned the wifi on and it connected, but non on my apps are working cause they need internet connection. i have reset the networks, reset the wifi connection and turned the phone on and off multipule times, and tried all the settings but nothing is working! please help

I went into the apple store and how it was explained to me was that the new ios7 update made the ipad even more exclusive and personal. So if you have any apps that were downloaded by an ex or a friend using their apple id on your device it won't sync, because updates of apps are tied to apple id accounts. music is not included because songs are not updated. but if you try to delete apps that were not purchased under your apple id it should fix the problem.

[SOLVED!!!]Need help getting internet cafe software to execute...

Already submitted to AUR: https://aur.archlinux.org/packages.php?ID=56282
I'm building a PKGBUID for a program called Cafe Pilot. I'm using it for the computer lab in my shop and could use some help getting it to execute properly. I'm pretty sure the PKGBUILD is good, because I can build and install just fine, but I get the error message below when I try to execute via CLI:
Caused by: java.lang.ClassNotFoundException: CafePilot_Server.jar
at java.net.URLClassLoader$1.run(URLClassLoader.java:217)
at java.security.AccessController.doPrivileged(Native Method)
at java.net.URLClassLoader.findClass(URLClassLoader.java:205)
at java.lang.ClassLoader.loadClass(ClassLoader.java:321)
at sun.misc.Launcher$AppClassLoader.loadClass(Launcher.java:294)
at java.lang.ClassLoader.loadClass(ClassLoader.java:266)
Could not find the main class: CafePilot_Server.jar. Program will exit.
not quite sure what this means... do I need to use JRE, or can i get away with openjdk on this? ANY input would help... working on the companion client package, but wanted to get the server out of the way first so I can streamline the creation of the client's PKGBUILD... Thanks in advance!
SOLUTION: editing of PKGBUILD and .sh file as posted below
https://bbs.archlinux.org/viewtopic.php … 4#p1051824
Last edited by CPUnltd (2012-02-02 23:42:05)

1. The usage of the -classpath switch is incorrect. Per manpage, you invoke it like "-classpath <somepath>". So when you call
java -classpath -jar CafePilot_Server.jar
java 6 will throw an "NoClassDefFoundError: CafePilot_Server/jar". That means, java failed to find the class "jar" in the package "CafePilot_Server", which is not exactly what you intended to do (in java packages are delimited by dots like com.mypackage.MyClass, which would go into a file hierarchy like ./com/mypackage/MyClass.class). java 7 will give you the more shorter message: "Could not find or load main class CafePilot_Server.jar"
So in short, the -classpath flag eats your -jar flag. The easiest way around this is, to omit "-classpath", which will result the classpath defaulting to the current directory, or to call "-classpath /opt/CafePilot_Server/".
2. About the '/usr/lib/jvm/java-6-openjdk/bin/java' part: Is there a specific reason to not call the "java" command directly? On a java 7 install:
$file `which java`
/usr/bin/java: symbolic link to `/usr/lib/jvm/java-7-openjdk/jre/bin/java'
And on a java 6 one:
$file `which java`
/usr/bin/java: symbolic link to `/usr/lib/jvm/java-6-openjdk/bin/java`
So i would promote one of the following options:
a)
#!/bin/bash
cd /opt/CafePilot_Server
java -jar CafePilot_Server.jar
b)
#!/bin/bash
java -classpath /opt/CafePilot_Server/ -jar /opt/CafePilot_Server/CafePilot_Server.jar
I do not really have an idea of what the program is supposed to do, but as far as i can see, b) has the advantage, that you do not need to call it as root, since the program will write some logs to the current directory. So when you call a) as a normal user, you will get an Permission denied error, because the programm could not write its derby.log to /opt/CafePilot_Server/, whereas for b) you could call it from your home directory, and you will get the log right there.
Both options assume, that the lib/ directory is installed as mentioned in my previous post.
Last edited by Wey (2012-02-02 22:37:39)

My music is so disorganized i need to get it working for me but how?

my music all works fine but it goes in order by the Album name then the artist but i have a lot of Albums that include many different artists and they show up in my library as they are in different albums....it is really annoying when i want to listen to a Album click on the song in the album and it says that is the only song in the album when i now there is more then that in that album....it only does this to CD's i rip into my computer the music i buy from itunes does not do this.....i have tried going to view and changing the album settings but it just does not want to change.... how can i get it to do what i want? to put all the songs in the album they belong too....

I too am also having the same problem with viewing songs by album. I'm sure there is a simple explanation to solve this problem, but after surfing the help menus and discussion pages, I can't seem to find the answer. With my problem, this example will illustrate my fustration. My favorite CD is "In the City" by Kevin Rudolf. When I go to play the album on my iPod Nano, which I just purchased, the album is shown in 'chunks' instead of one album itself. The cd has a total of 12 songs in it, but when I go to the menu on the iPod to select the album "In the City" there are a total of 5 of these albums, each with 1 to 4 songs in each. This is rather annoying in how I would just like to listen to my favorite album in one go, in the proper order as per on the cd, and I can't do this. I'm sure the problem is very simple to fix, and I look forward to using the brand new iPod nano which I have purchased. But sadly if I cannot fix this problem, then I will return the product and all the accessories purchased with it for a different competitors product. Keep in mind, this album is not the only one that is in my selection of music that does this. There are many albums that are sliced up. So fixing this one album in example, will hopefully fix them all.

Need help getting php working, apache not evaluating php doc.

Folks, I have been trying for some time to get JetPhoto Server to work on Snow Leopard Server. It was so easy with SL Client.
In any case I cannot get "<?php phpinfo(); ?>" to be evaluated in Safari and I am not sure why.
Essentially I am taking it step by step to understand why it's so hard to get things up and running - first making sure things apache and php are playing nice.
PHP is enabled
registerlongarrays is on
engine is on
All Safari returns is the same php call instead of the config info.
Please advise.

Default web page is on a second drive right now now that JetPhoto server is running. Otherwise the default is in the default webserver/documents/ directory. I just have Server Admin settings pointing to the photo server until I can restore the company homepage I used to have.
output from first command:
drwxrwxr-x 26 root admin 884 Jul 26 15:37 .
drwxrwxr-x 7 root admin 238 Apr 26 14:35 ..
-rw-r--r--@ 1 lpiadmin admin 12292 Jul 26 15:38 .DS_Store
-rw-rw-r-- 1 root admin 3726 May 18 2009 PoweredByMacOSX.gif
-rw-rw-r-- 1 root admin 31958 May 18 2009 PoweredByMacOSXLarge.gif
-rw-rw-r-- 1 root admin 5063 Jul 20 2009 applestylesheetoverrides.css
-rw-rw-r-- 1 root admin 2636 Jul 20 2009 base_layout.css
-rw-rw-r-- 1 root admin 3754 Jul 20 2009 error.html
-rw-rw-r-- 1 root admin 3754 Jul 20 2009 error.html.default
-rw-rw-r-- 1 root admin 7782 Jul 20 2009 favicon.ico
-rw-rw-r-- 1 root admin 56 Jul 20 2009 grayline.gif
-rw-rw-r-- 1 root admin 3811 Jul 20 2009 grayx.jpg
-rw-rw-r-- 1 root admin 5094 Jul 24 2009 index.html
-rw-rw-r-- 1 root admin 5094 Jul 24 2009 index.html.default
-rw-rw-r-- 1 root admin 44 Nov 20 2004 index.html.en
-rw-rw-r-- 1 root admin 271 Jul 20 2009 info.php
-rw-rw-r-- 1 root admin 2296 Jul 20 2009 logo.gif
-rw-rw-r-- 1 root admin 4399 Jul 20 2009 main.css
-rw-rw-r-- 1 root admin 2028 Jul 20 2009 osxserver.gif
-rw-rw-r-- 1 root admin 1278 Jul 20 2009 poweredbymacosxserver.gif
-rw-rw-r-- 1 root admin 454 Jul 20 2009 v5backgroundlink.jpg
-rw-rw-r-- 1 root admin 435 Jul 20 2009 v5backgroundlinkhover.jpg
-rw-rw-r-- 1 root admin 1580 Jul 20 2009 v5backgroundmain.jpg
-rw-rw-r-- 1 root admin 8889 Jul 20 2009 v5backgroundtop.jpg
drwxrwxr-x 4 root admin 136 Jul 20 2009 weblog
drwxrwxr-x 5 root admin 170 Apr 26 14:35 webmail
output from second:
-rw-r--r-- 1 root wheel 68732 Mar 30 21:34 /etc/php.ini.applesaved
-r--r--r-- 1 root wheel 68970 Jan 29 18:25 /etc/php.ini.default
-r--r--r-- 1 root wheel 68727 Mar 16 09:08 /etc/php.ini.server-default
-rw-r--r--@ 1 lpiadmin staff 68729 Jul 26 12:18 /etc/php.ini.txt

Need help getting PSE5 working on Vista 64-bit

I've read in the Forums that it will work if I download the 5.0.2 update, but when I try to do the download, I get an error message saying it will not work with my version. Can anyone help with this? Thanks.

fluffyhermie wrote:
I've read in the Forums that it will work if I download the 5.0.2 update, but when I try to do the download, I get an error message saying it will not work with my version. Can anyone help with this? Thanks.
I have PSE 5.0.2 working under Vista 64.
Perhaps you could clarify your statements and add some missing details?
You said "when I try to do the download" you get an error message. Do you mean "when I try to install"?
Have you previously installed PSE5 on this computer, and you are trying to update to 5.0.2?
Could you give us the exact error message, and let us know exactly what is happening when the error message appears?

Need Help Getting Internet Capabilities to iPhone

Hi there, so my Moms phone went into Recovery Mode and I fixed that using TinyUmbrella. However, now the phone has no Internet at all, nor can she send any messages. I don't know about receiving but I doubt that would work either. If someone could help A.S.A.P that would be great. Thank you!

Well thats because you've hacked the phone using Tiny Umbrella, it's against the forum term of use to provide help for hacked or jailbroken phones.
Use google.

Need to get internet working on X3 00

Similar Messages

Maybe you are looking for