NEO 4 platinum sli sound issue...Please help

Hello,
I am having a "no sound" issue as well...but I have the -5v line....and a 24 pin connector. I have read as much as I can about this and cannot figure out why I still have no sound...
I am using a Thermaltake 680W Power Supply. It has three 12V rails 15A, 15A, and 8A. The -5V rail is 1A
The SB Live 24 bit drivers are loaded
All shows well in Device manager
I did run the sound test in Windows and the microphone works!
But no sound.... Any suggestions? Help....
I am running the orginal 3.0 bios...
Thanks
-M

It was set to using the analog outs....
I have tried everything....no go....I finally just slapped in my Audigy 2 ZS!
Did not want to mess with it any more.....
It took me three days to put together this SLI water-cooled system....I do not want to RMA for that....
Everything elase works great..
Thanks!
-M

Similar Messages

Msi k8n neo 4 platinum sli sata issue?

hi i am planning to buy a new motherboard and i decided to buy k8n neo 4 platinum sli board. but recently i heard that it has an issue with
silicon image SIL3132 controller that If there was no drive connected to the controller, the system wouldn't complete the POST. does that issue resolved now? please tell me. any new bios update for that?

hi satya123 ,
Quote
silicon image SIL3132 controller that If there was no drive connected to the controller, the system wouldn't complete the POST
not heard of that one.
But it's easily sorted :-
Bios - Onboard Devices
OnBoard Sil3132 RAID
This setting controls the onboard Sil3132 RAID chip. Setting options: [Enabled],
[Disabled].
OnBoard Sil3132 Mode
This setting allows you to select either SATA and RAID mode for the onboard
Sil3132 RAID chip. Setting options: [SATA], [RAID].
just set OnBoard Sil3132 RAID to disabled.
Sorted

MOVED: Looking for feedback on K8N Neo NF4 Platinum SLI, LUV THIS BOARD

This topic has been moved to Overclockers & Modding Corner.
Looking for feedback on K8N Neo NF4 Platinum SLI, LUV THIS BOARD

Im no pro but with your raid setup you need to stay with bios 3.0, 3.1 or 3.2. I understand that 3.3 & 3.4 causes problems but the new 3.53 beta bios fixes the problems in 3.3 & 3.4. See below:
https://forum-en.msi.com/index.php?topic=80933.120
Regarding your pcie clock, if you are using coolbits and nvidia drivers only (no MSI drivers at all), then I have used nvidia's ntune to help set the clock. For my x1 msi 6600gt, working backwards from the bus speed optimization it equalled to 106...but I am really not good at this and you should post your question under the VGA portion of this forum for a better answer to that 1 question.
However, using MSI's DOT works well too and its automated.
Btw, the pcie setting has nothing to do with your cpu/memory overclock.

NO Sound; experts please help

I currently have no sound on my HP Spectre XT Ultrabook PC!!! Upon buying the laptop it had Beats audio on the laptop. That stopped working recently, but I still had the normal reduced audio, until that stopped completely soon after. I have tried multiple things to fix this problem, all without success; I tried troubleshooting the problem, I tried updating the audio driver (it said I already had the most current version), I tried uninstalling and reinstalling the driver, I tried updating the BIOS on my computer and NONE of these have worked; I still have no sound! Please help to fix this problem!
The product number is B6V42PA#ABG and it currently has Windows 7 Home Premium installed on it!

Hi
Please try doing a system restore to the date where unit was working fine. In case this does not work last option is to run a recovery please back up your data. This does not work please call HP technical support & get the Speaker replaced.
Let us know how it goes!
"I work for HP."
****Click the (purple thumbs up icon in the lower right corner of a post) to say thanks****
****Please mark Accept As Solution if it solves your problem****
Regards
Manjunath

Mid 2010 15" MBP i5 A1286 POWER ISSUE-PLEASE HELP-

The MBP works fine when mains connected but the only issue is every time I take the charger out it shuts down on me!!! So I have checked with a multitester & looks good the only thing i find hard to check for power is the battery itself as its hard to get a good connection, also I took to local Apple store & they checked with a new battery but said its still same issue so the guy disconnected nearly all the connecters off to check if they causing issue & he said now the battery is charging.
So they still have the laptop to do further tests etc, but I’m not sure what could be the problem hear as maybe there is some component which is bad so the battery’s not charging or what else could be the issue please help & advice as I’m really confused as if it was something to do with the logic board then surely it would not even charge even after checking with the multitester or like Apple genius done by disconnecting other components...
ANY HELP OR ADVICE WOULD BE HELPFULL,
THANKS GUYS

THANKS FOR THE HELP GUYS!!! BEEN AROUND 5 DAYS & NOT ONE PERON HAS HELPED...
BUT YEAH THANKS AGAIN...
WASTE OF TIME THIS IS...

Trackpad Issue - Please Help!

Hi there,
Hope you can help me out here.
I've recently purchased a 15" i7 Macbook pro. The machine is but 3 weeks old &, of course, very well looked after.
A few days ago, the built-in trackpad started behaving eratically. Cursor moving by itself, not responding to touch, clicking and opening things involuntarily. Not good at all. Many users seem to have had this exact same issue.
These problems seemed to miraculously stop after a few re-boots and possibly a software update? I really couldn't tell you what resolved the problem.
Unfortunately I now have a totally different problem.
There is a thin, possibly 8 to 10mm horizontal strip across the centre of the trackpad that no longer responds to touch. If I move my finger from the botom of the trackpad upwards (or vice versa), the cursor will stop momentarily as it passes over the horizontal strip. The buttons are fine and the rest of the trackpad is fine. For the moment, I've increased the cursor acceleration so that I can at least navigate round the screen with a smaller area of the trackpad. USB magic mouse seems to work fine.
If anyone else has experienced this &/or found a solution for this issue, please help me out here. I have rifled through endless threads about MBP trackpad issues with little success & do not live close to an apple store/genius bar.
This is a 3 week old machine that cost me a small fortune. To be getting software/hardware issues so early on in it's lifespan is really rather worrying for the future.
Appreciate your help here.
J

I'm not sure what caused this, but I extended my lunch break and drove the machine down to the Westfield apple store. I didn't have an appointment with the Genius Bar but I managed to persuade one of the staff to speak to a technician in the workshop. She came back into the store and told me that they had replacement trackpads and that , considering the machine was only 3 weeks old, the technicians kindly sandwiched the repair into their timetable at zero cost. 2 Hours later, I now have a perfectly functioning trackpad/machine.
I can't thank them enough.
My only gripe is that I couldn't speak to a technician to find out what the problem was, how they resolved it or what causes these issues for future reference. Understanding why these problems occur often helps to build your own framework of understanding. Most of the threads i've read about trackpad issues are largely unresolved with people only speculating the problem/solution.
The initial issue I had with the trackpad's erratic behaviour seemed to be a well known problem that many are associating with a trackpad firmware update. Unless by pure coincidence I had an immediate & major hardware fault after it, which is unlikely, my personal guess is that the two issues were related.

Transport Issue Please help

Hello,
I have got a major prolen during transport.
I have GEMPLOYE1 Which is a time dependient master data. which has Attribute called 0COUNTRY_ID.
I have a custome attribute Called Actual PSGroup/Grade GPAYSCGR which has a compounpunding attribute 0COUNTRY_ID
Now when I am trying to transport PSGroup/Grade GPAYSCGR to QA that transport is failing , the log massage is
Characteristic GEMPLOYE1: Attribute GPAYSCGR compounded to 0COUNTRY_ID has a diff. time-dpdncy
If any one saw this issue, please help me to fix the same.
Samit

Hi Venu,
We can't add authorisation objects on Individual servers.We need to add authorisations on BWD ie Dev system and transport to BWI QUA system.This is the Process we need to follow as per our rule set.
So,As the problem mentioned above if i add some auth. objects on BWD DEV system and transport it to BWI QUA system,it is getting transported Successfully to BWI,but the auth.objects what i have added on BW DEV system is not found on BW QUA system.
What could be the problem for that,Is that the problem with transports like TP error or is it related with some tables of auth.objects...................
Could u please analyse the problem and tell me the solution for this..........
Thanks Much
Swapna.D

Headerrenderer issue -Please help

Headerrenderer issue -Please help
hi
I have a datagrid and I am doing a custom sorting on the grid(by getting data from DB).
I achieve this by capturing the headerrelease event of datagrid .In thee venthandler I will query from DB and do event.preventdefault to prevent standard grid sorting.
Now I need to display my own custom ascending/descending arrows in the header.i have created an header renderer for this,
In the headerrenderer I am lsitening to the headerrelease event of datagrid and in the eventlistener, as per the sortfield, i am trying to make the sort arrow visible/invisible.
But somehow making the sort arrows visible/invisible is not working.The initial arrow works fine.it is shown the correct column(Name) as done in the init() method.
The eventhandler is invoked on clicking the column headers and all the alerts are shown.
Please see the headerrenderer code below and help me.(code is not complete only the relevant part is included)
<?xml version="1.0" encoding="utf-8"?><mx:HBox
xmlns:mx="http://www.adobe.com/2006/mxml" width="100%" height="100%" horizontalScrollPolicy="off" creationComplete="init()" implements="mx.controls.listClasses.IDropInListItemRenderer">
public function init():void{
headerLabel = dataField.label;
_dataGrid.addEventListener(DataGridEvent.HEADER_RELEASE,sortChanged,false);
if(_dataField.localeCompare('Name')==0)asc.visible=true; }
private function sortChanged(e:DataGridEvent){
var dg:DataGrid=e.currentTarget asDataGrid;
varcolumn:DataGridColumn = DataGridColumn(e.currentTarget.columns[e.columnIndex]);if(_dataField.localeCompare(e.dataField)==0)
if(asc.visible ||(!asc.visible&&!desc.visible))
Alert.show(
'in..');
asc.visible=false;
desc.visible=true;
else if(desc.visible){
asc.visible= true;
desc.visible=
false;
else{
asc.visible=
false;
desc.visible=
false;
]]>
</mx:Script>
<mx:Text text="{_headerLabel}" />
<mx:Image source="{ascIcon}" id='asc' visible="false">
<mx:Image source="{descIcon}" id='desc' visible="false"/>
</mx:HBox>

I got the solution!!
i need to assign the headerrendereer to the columns dynamically inorder for this to work:
if anybody wants to know details of solution let me know

K8N Neo 4 Platinum Sli & Athlon 64 3200

Somebody know if the mobo "K8N Neo 4 Platinum Sli" can work good with an Athlon 64 3200 (939)

Quote from: jrb357 on 10-March-05, 11:29:32
It'll work just fine with a 3200+. Just use some quality TCCD ram. If you plan OC'n some people are having some difficulty getting over a 220fsb. It seems that the newer cpu's are more prone to this, ones with a manufaturing date of under 0451 seem to OC better.
Aint that the truth!
IF you are planning to o/c then forget about this board for the moment, until a new bios is available......
That is the only downside to this board, otherwise its a very stable board!
I have corsair 4400 and cant get over 220 fsb with it....

MSI K8N Neo4 Platinum SLI sound needs -5V; newest Antec 550W has no -5V rail

I came within a whisker of ordering a non-returnable 3700 Venice, MSI K8N Neo4 Platinum SLI mobo and an upgraded Power Supply, Antec's newest 550W PS the TP2-550 EPS12V ($117). This has dual 2x24pin 12V 19A rails and is touted as the new V2.0 EPS12V/ATX12v compatible power supply for high performance SLI systems. By accident I came across a page at MSI for this mobo
http://www.msi.com.tw/program/products/mai...ail.php?UID=641
At the end is this warning: MSI Reminds You...
• For this model, you must use a Power Supply which has a -5V pin supply. Also, the users manual which I downloaded on Pg 2-10 says the same thing
The above Antec PS specs do not show a -5V rail, nor does an Enermax 600W I looked at. The V2.0 specs for ATX12v which added 2x24pin 12V rails dropped -5V rail from the spec and it appears MSI is not conforming to the spec (See Antec response at end) None of the web sites selling these PS & mobos contain any warning. I vaguely recall from a forum a while back it may have something to do with the Soundblaster system in the mobo.
http://www.antec.com/us/productDetails.php?ProdID=22551 (click specifications)
Isn't this a major showstopper which is going to cause a lot of grief for those of us upgrading to SLI systems using this mobo and upgrading our PS to the newest & best power design? We won't know the PS won't work until we build the system.
Regards, Ron
Antec reply to me:
>>>>Thanks for the link. Since MSI's website does state the motherboard needs the -5v, the True550EPS12V will not work with this motherboard. The Standard (http://enhanceusa.com/documents/atx12v_v2.01.pdf) has removed the use for the -5v rail and it is no longer needed. MSI has not manufactured that motherboard to the Standard. Finding an ATX12V v2.0 power supply with the -5v might be hard to find. You should contact MSI for a compatibility list of power supplys that were tested to work with the K8N SLI Platinum.

Quote from: ccve3 on 21-May-05, 07:27:40
Wow!! syar2003 thanks for that post. I've spend an hour going through it & fasteddies links. Now I are a power expert. The dual rail argument is enough for me to go back to the MSI K8N Neo4 Platinum SLI with one of the single rail PS -5V units listed by fasteddie. The only question left now refers to computerpro3 recommendation on ultra power supplies for SLI
>>I quite simply wouldn't dream of putting anything else in my machine. Keep in mind, this section is for 2x 6800 models, not the 6600's which most any good psu will handle (like Antec Neopower, ocz 520, etc). . Pc Power and Cooling 510 Deluxe SLI edition (refer to list)
2. Zippy/Emacs 550-700w models
3. OCZ 600w (personally I would get the pcp&c for the price, but it's been proven here, so I'll be fair...).
These are really high end, expensive and only 3-4 choices. Since I'm getting one 6800GT and eventually another & possibly eventually a 4800 X2, I was hoping the OCZ 520W would do it but computerpro3 says Powermaster 520 isn't good enough for SLI. I found that there is an OCZ 600W ATX12 dual rail which surprisingly has a -5V rail needed for K8N Neo4 SLI Soundblaster. Will this meet computerpro3's preference for a high end PS for SLI systems even though I'm losing the 1 rail advantage. Maybe the 600 Watts just overwhelms the 1 rail/2 rail question.
Thanks again for the teriffic help
Regards, Ron
Wondering what you settled on. I got the Antec TP550 and it's flawless on the board. I even have the older 20pin model which works perfectly (including sound). If you really wanted what I would consider to be a top dog (pcpower and cooling), and find the -5v rail missing, all you have to do is place a phone order and request they add a -5v rail. It's a minimal cost and a total solution for having everything. Just my $0.02

How to fix imessage error on ios8.1.2 .. Already reset network still same issue please help

How to fix imessage error on ios8.1.2 .. Already reset network still same issue please help

Hi ashmanryan36,
Thanks for using Apple Support Communities. Based on what you stated, it sounds like you are having trouble with iMessage. It looks like you have already done some troubleshooting. I would recommend that you read these articles, they may be helpful in troubleshooting your issue.
If you can't send or receive messages on your iPhone, iPad, or iPod touch - Apple Support
You did not mention what the error was but since you are running 8.1.2 and update is available and my help.
Update the iOS software on your iPhone, iPad, and iPod touch - Apple Support
Cheers,
Mario

IDE/SCSI Problems with Neo 4 Platinum/Sli

I am routinely getting Event 11 and Event 9 errors in my event viewer which are basically "The controller detected an error on device " then lists a controller and a harddrive. I never got errors like this on my old rig (an Asus A7Pro Motherboard) and I'm using many of the same components. I get controller errors on my Adaptec Card/HDD which is very odd since I'd imagine they were totally separate from the nVidia or Silicon Image SATA/IDE on the board.
New Rig:
MSI Neo4 Platinum/SLI
Athlon 64 3500+
Thermaltake K8 SilentOrb
1 GB (Dual Channel 512MB DDR) Kingson Hyper-X
1 BFG 6800GT OC (PCI-E) (with an Artic Cooling NVSilencer rev2)
Turtle Beach Santa Cruz (although I may change to the onboard 24bit SB Live)
Adaptec 29160 PCI Ultra 160 Controller
Belkin 54G Wireless Adapter
Pioneer SCSI II slot load DVD-ROM drive
Toshiba SCSI II CD-R/CD-RW drive
500+ Watts Vantec Stealth PSU (with good voltages on all rails)
74GB Western Digital Raptor (SATA connected to Slot 4 - nVidia SATA channel, no RAID)
80GB Western Digital 8MB RAM, Special Edition UDMA 4 IDE HDD
36GB Seagate Ultra2 Cheetah
Old Rig had the WD IDE drive, the SCSI card and dvd/cd drives, the sound card, and the wireless card.
I originally had a 40GB IDE Maxtor drive (which I replaced with the Digital Raptor) but it had all sorts of event 11 and 9 errors and exhibited slow IDE performance and even created conflicts with the WD IDE Drive outside of windows. I had problems running the WD diagnostsics software (runs in DOS) when the Maxtor drive was set to primary master on either of the two IDE channels.
What I'm wondering is if there is a BIOS upgrade or Driver release or anything that fixes these problems for people. I'm using BIOS 3.1 (when I upgraded to Bios 3.4, my computer would BSOD in normal and safe modes, and I didn't feel like reinstalling Windows, so I downgraded back to 3.1) The nVidia IDE drivers (6.53) caused massive problems with my drives (event 11 and 9 and endless lockups with the IDE light remaining on, requiring cold boots) so I ditched them for the windows default drivers.
I'm curious if people have checked out their own event viewer (Control Panel->Administrative Tools->Event Viewer->System for all you non-power users) and checked out the errors listed there.
The only other stability problem sI've noticed is when playing Half Life 2 in 1280X1024 resolution (1024X768 didn't have the problem) would cause complete crash of the machine. Monitor would lose signal and a cold boot was required... reset button didn't fix the problem. I figured this might be a cooling issue so I checked temps and they were fine. Then I figured it may be a power problem so I upgraded to the Vantec Stealth PSU (from my Antec 380W SilentPower) I haven't tested HL2 extensively since, so I'm not sure if this problem has gone away. The other problem occurs when trying to rip a CD in iTunes with "cd error checking on" System totally stalls out and a cold boot is required to get the SCSI happy again. If I rip using error checking off, things seem to work, however I get a problem sometimes where a track will suddenly squeel and crack in the middle and then the remainder of the song will be the first track on the album. The next track in the sequence will have a half second blip of the previous track on it, essentially meaning that two tracks are "broken rips" Ripping in AudioGrabber with ASPI doesn't seem to exhibit these problems.
Any similar experiences or sollutions/advice would be greatly appreciated.

It's been fixed for the Neo2. I am using a modded version called 1C3 EasyBios [rev.2]. I think it is based on the latest version or new beta of the official 1.B. Read all about it:
https://forum-en.msi.com/index.php?topic=88384.0
https://forum-en.msi.com/index.php?topic=59711.msg622296#msg622296

Vista Premium Home Edition 32-bit on newest Macbook Issues PLEASE help!

Please someone help me with my problem, I'm begging! I've asked around a bunch of places and everyone comes back to me with "well it's a mac.. use it as a mac why do you have vista on it" and never seem to help me. I love my mac, but I also use Vista for many other programs.
Okay here's some backstory...
I recently had to buy a new macbook because my old white macbook came back to me unrepairable! So I had bought the newest model of the macbook, the aluminum 13-inch. Now on my old white one I had installed vista no problems at all, no issues. It ran beautifully! Now I thought I'd have no issues doing the same on the new macbook. Boy was I wrong! I portioned my disc - installed vista, installed the bootcamp drivers and started vista.
It was fine for a while but then I started getting sound cut outs and screaching noises! When I am gaming the sound cuts out completely but not before the game freezes. Then I started having issues watching videos and listening to audio on firefox. Then it'd crash completely! Now it's started shutting off completely giving me a blue screen for a couple seconds telling me there may be a conflict or driver issue. It doesnt stay on long enough for me to read but I ended up checking windows problems and solutions and found this:
"This problem was caused by a compatibility issue between Intel 82801GBM (ICH7-M) LPC Interface Controller - 27B9 and this version of Windows.
Intel 82801GBM (ICH7-M) LPC Interface Controller - 27B9 was created by Intel Corporation and is distributed by Apple Inc.."
Also driver not found? - "Windows detected a new device attached to your computer, but could not find the driver software it needs to make the device usable. Each device manufacturer typically includes driver software of a CD that comes with the device, or as a download from its website. The hardware ID of your device is ACPI\APP0001."
I don't know how to fix it. I've been trying everything - reading forums, trying to update drivers, reinstalling bootcamp drivers, and vista repair... I just have no idea what to do! Please help me!!! Please please! If you need more information ask for my email so I can talk to you more in-depth so I don't go insane trying to figure this out!

What do you want someone to say or do.
The story slides into information about Intel chipsets and crashing. That to me says take it into Apple and have AppleCare do something.
There is no reason to deal with an issue. A Mac is a personal computer. There is nothing that says it can't run Linux or Vista or has to run Leopard (though it isn't supported on older versions of OS X).
I've used Vista for over two years now, from RC1 pre-release to the latest SP2 beta.
Is your version of Vista SP1 or the older original?
I've found lately that I need to install some software even before Vista starts doing all the updates. Apple Boot Camp but also AV software etc. HOWEVER, given some of the reports, I sometimes wonder if the Apple Windows drivers are current and were tested on late 2008 to work with Vista and XP SP3.
I would think Vista SP1+ would be best bet. I'd even install Vista and then see when Windows 7 beta is officially available to the public, it runs better on laptops than Vista or XP. Better battery life, support for mobile and wireless devices etc.
You could play around and I've downloaded drivers or looked for drivers on Intel, something you would do on any PC running Vista. Maybe these links and discussions or Intel's. And find people and places that support you rather than "lecture." I don't know, haven't read up, on the device, or use a MacBook, but maybe these will help you.
"Intel 82801GBM (ICH7-M) LPC"
From Intel: "Intel 82801GBM"
A number of reviews have come out looking at "who makes the best Vista capable laptop" and MacBook Pro and Air have both gotten high marks from reviewers like ComputerWorld.

Sound problem, please help

Hello, An year or 2 ago, I bought this HP computer, a DX7200 Slim Tower. Due to it's poor performance, I decided to buy another GPU, an Asus R7240. I installed it, and then noticed the sound was not working anymore. To my understanding, it was because the sound card was no longer detected. Fastforward half an year. I just decided to play my games without sound. I then moved a considerable distance and had my computer shipped over in a truck. While in truck, my computer was probably shaken a bit and the graphics card was no longer properly "plugged" in the slot and thus didn't work. I started my computer without knowing this and then noticed that I could the sound was working. I also noticed a severe issue with my FPS on games so I figured that there must be a problem with the graphics card; I therefore opened my case, put the gpu back how it should be. And then I start my computer and notice that the sound is no longer working. tl;dr GPU= No soundNo GPU= sound I really want to fix this now, please help me! This is a screenie of what I see wen I click on "playback devices"

Satellite A105-S4384
Try reinstalling this driver.
Realtek Audio Driver for Windows XP/2000
-Jerry

MacBook Pro: Sound Issue. Help needed.

Hi. Recently, my headphones (I use on my iPod Touch too), and my MacBook Pro sound have not been working lately. I have been looking for a red light, but cannot find it. I left my Mac asleep (with headphones in!), and when I opened back up, niether my sound on both haven't been working. I'm trying to configure my Mac settings, but I'm stuck.
Can someone please help me answer this? If you do not know the answer, and have the exact (or close to the exact) same problem, please do not post. I will need all the assistance I can possibly get. Thank you so much.
~AppleFan17

In troubleshooting, often a concrete or exact solution is elusive. Here's what I can offer:
Troubleshooting no audio issues with built-in speakers: http://support.apple.com/kb/TS1574
Reset SMC: http://support.apple.com/kb/HT3964
Reset PRAM: http://support.apple.com/kb/ht1379
Good luck.

NEO 4 platinum sli sound issue...Please help

Similar Messages

Maybe you are looking for