Netscreen firewall authentication by Cisco ACS
Since Netscreen firewall only supports RADIUS authentication, is Cisco ACS server able to support it? If yes, which version and where can I find more info about it?
If it supports RADIUS then ACS should be able to support it.
I belive the latest version of ACS is V6.33, you can download a trial version from this site.
All the information you require should be here:
http://www.cisco.com/en/US/products/sw/secursw/ps2086/index.html
HTH
PJD
Similar Messages
-
User authentication in Cisco ACS by adding external RADIUS database
Hi,
I would like to configure the below setup:
End user client (Cisco Any connect/VPN client) -> ASA 5500 (AAA client) -> ACS server -> External RADIUS database.
Here ACS server would send the authentication requests to External RADIUS server.So, i have added the external user database (RADIUS token server) in
ACS under External databases.I have added AAA client in Network configuration (selected authenticate using RADIUS(VPN 3000/ASA/PIX 7.0) from the drop down.
Here how do i make ASA recognize that it has to send the request to ACS server. Normally when you use ACS as RADIUS server you can add an AAA server in ASA and test it.But here we are using an external RADIUS server which has been configured in ACS, so how do i make ASA to send the requests to ACS server?
Any help on this would be really grateful to me.
Thanks and Regards,
Rahul.Thanks Ajay,
As you said nothing needs to be done on ASA side, if we are using an external user database for authentication.
Im a newbie to ACS and this is the first time i'm trying to perform a two factor authenticaton in Cisco ACS using external user database.
By two factor authentication i mean, username + password serves as first factor (validated by RADIUS server), username + security code (validated by RADIUS server) serves as second factor.So, during user authentication i enter only username in username field and in "password" field i enter both "password + security code". Our RADIUS server has already been configured with AD as user store, so we dont have to specify AD details in ACS. I have done the following in ACS to perform this two factor authentication.
-> In external user databases, i have added a external RADIUS token server.
-> In unknown user policy , i have added the external data base that i configured in ACS into the selected databases list.
-> under network configuration, i have added the Cisco ASA as AAA client (authenticate using RADIUS (Cisco VPN 3000/ASA/PIX 7.x+)).
Just to check whether user authentication is successful, i launched the ACS webVPN using https://IP:2002, it asked me to enter username and password. So, i entered username and in password field i entered "password + security code". But, the page throws an error saying "login failed...Try again".I cant find any logs in external RADIUS server.
Here is what i found in "Failed attempts" logs under Reports and activities.
Date,Time,Message-Type,User-Name,Group-Name,Caller-ID,Network Access Profile Name,Authen-Failure-Code,Author-Failure-Code,Author-Data,NAS-Port,NAS-IP-Address,Filter Information,PEAP/EAP-FAST-Clear-Name,EAP Type,EAP Type Name,Reason,Access Device,Network Device Group
02/28/2012,00:31:52,Unknown NAS,,,,(Unknown),,,,,10.204.124.71,,,,,,,
02/28/2012,00:41:33,Unknown NAS,,,,(Unknown),,,,,10.204.124.71,,,,,,,
02/28/2012,00:42:18,Unknown NAS,,,,(Unknown),,,,,10.204.124.71,,,,,,,
Filtering is not applied.
Date
Time
Message-Type
User-Name
Group-Name
Caller-ID
Network Access Profile Name
Authen-Failure-Code
Author-Failure-Code
Author-Data
NAS-Port
NAS-IP-Address
Filter Information
PEAP/EAP-FAST-Clear-Name
EAP Type
EAP Type Name
Reason
Access Device
Network Device Group
02/28/2012
00:42:18
Unknown NAS
(Unknown)
10.204.124.71
02/28/2012
00:41:33
Unknown NAS
(Unknown)
10.204.124.71
02/28/2012
00:31:52
Unknown NAS
Am i missing any thing in configuration side with respect to ACS?
Thanks -
CS-MARS user authentication using Cisco ACS
Hi,
I would like CS-MARS (Web Interface) user authenticaiton to be done by Cisco ACS Server. Please let me know, either it is possible or not? And if possible then reply how to configure it.
Thanks and Regards,
Ahmed Shahzad.Hi,
I would like CS-MARS (Web Interface) user authenticaiton to be done by Cisco ACS Server. Please let me know, either it is possible or not? And if possible then reply how to configure it.
Thanks and Regards,
Ahmed Shahzad. -
Configuring Cisco ACS 5.1 with Juniper Netscreen Firewall wit Radius & Tacacs+
Hello,
Can anybody tell me the step-by-step configuration of Cisco ACS 5.1, to configured it with Juniper Netscreen Firewall for radius & tacacs+ authentication and authorization?
I am able to configure this with Cisco ACS 4.2 with customise VSA file but can't understand how to configure it on ACS 5.1.
Thanks in Advance.Hi Eduardo,
Can you tell me how to map ACS 4.2?
service=junos-exec
local-user-name=Engineering
Into the new "shell profiles" on ACS 5.2? How do I verify these attributes are passed onto ACS 5.2? I don't have access to a sniffer or tap nor do I have writes on this box. I have to instruct our systems folks to investigate. It has been a back and forth battle.
Also, I'd like to see where I'd map this on ACS 5.2. Keep in mind in both cases I have a JUNOS config mapping to a login user Engineer and operations respectively.
local-user-name=opertions
allow-commands=((^ping *)|(^mtrace *)|(^traceroute *)|(^monitor *))
deny-commands= ((^start *)|(^file delete *)|(^file rename *)|(^request *)|(^set cli restart-on-upgrade *)|(^set cli prompt *)|(^set chassis *)|(^set date *)|(^test *)|(^clear *)|(^op *)) -
Using Cisco ACS for Solaris login authentication
Hi all
I am planning to authenticate ssh logins to Solaris 8/9 systems using PAM and radius (while radius is considered the primary solution, tacacs+ could be used, too). The radius/tacacs+ server is provided by a Cisco ACS.
Can anybody out there confirm that the combination "Solaris & PAM & radius/tacacs+ & Cisco ACS" is correctly doing this authentication stuff? Is there anything to specially consider?
Thanks, DavidHard to comment with any certainty but provided the client implementation of RADIUS is sound AND the authentication protocol is one that ACS supports, eg PAP, CHAP, MSCHAP, LEAP, EAP (PEAP/FAST/TLS/GTC/MSCHAP) then should be fine.
-
Cisco ACS 4.2 authenticating Cisco 4710 ACE appliance failed
Hi,
I've got a problem with Cisco ACS 4.2 authenticating Cisco 4710 ACE appliance.
ACS4.2 has been configured to use both internal and external database. It's been working fine for a couple or years.
Recently we bought a Cisco 4710 ACE appliance. When I use ACS4.2 internal username and password to login the Cisco 4710 ACE appliance, I have no problem. I can also see the passed authentication log on ACS4.2. However, if I use AD username and password, I couldn't login in. The message is "Login incorrect". I checked the failed attempts log on the ACS4.2, there was no log regarding the failed attempt. My AD username and password works fine on all other cisco routers and switches.
I've posted my AAA configuration of the 4710 ACE below. ACE is running on the latest version A4(1.1). Please help.
tacacs-server key 7 "xxxxxxxxxxxxx"
aaa group server tacacs+ tac_admin
server xx.xx.xx.xx
aaa authentication login default group tac_admin local
aaa authentication login console group tac_admin local
aaa accounting default group tac_adminHi,
Since the ACS is receiving the request.
Could you please ensure that In ACE on every context (including Admin and other) you have following strings:
tacacs-server host x.x.x.x key 7 "xxx"
aaa group server tacacs+ tac_admin
server x.x.x.x
aaa authentication login default group tac_admin local
aaa authentication login console group tac_admin local
aaa accounting default group x.x.x.x
On ACS side for group named "Network Administrators" you should configure in TACACS settting:
1. Shell (exec) enable
2. Privilege level 15
3. Custom attributes:
shell:Admin*Admin default-domain
if you have additional context add next line
shell:mycontext*Admin default-domain
After loging to ACE and issuing sh users command you should see following
User Context Line Login Time (Location) Role Domain(s)
*adm-x Admin pts/0 Sep 21 12:24 (x.x.x.x) Admin default-domain
Hope this helps.
Regards,
Anisha
P.S.: please mark this thread as answered if you fee your query is resolved. Do rate helpful posts. -
Cisco ACS 4.2.1 authentication problem
We are using cisco ACS 4.2.1 on windows 2003 to authenticate with windows 2003 Actice Directory. We have update Active directory server windows 2008 version. We have checked the configuration of ACS on windows database and no problem but we can't see in ACS dynamic user. I have authentication problem ACS 4.2.1 to Windows 2008 R2 active directory.
Hi there,
There is a section in the ACS 4.x where you can define if the ACS should show the dynamic users or not, make sure that this option is unchecked, for this go to External User Databases/Unknown User Policy/Configure Caching Unknown Users
Also if you are facing authentication issues with ACS 4.x and Windows 2008 R2, you may want ready my previous answer.
Let me know if this helps. -
[Cisco ACS] 11036 The Message-Authenticator RADIUS attribute is invalid
Hi,
I got many Cisco AP which are linked to 2 Cisco WLC.
On each WLC, I configured a primary and a secondary RADIUS Server.
RADIUS servers are Cisco ACS 5.2.0.26 (patch 10)
Primary and secondary ACS configurations are synchronized.
There are no problem between primary WLC and Cisco ACS (primary and secondary).
When secondary WLC requests primary Cisco ACS, I get this error "11036 The Message-Authenticator RADIUS attribute is invalid"
Secondary WLC automatically contacts secondary Cisco ACS and it works fine.
Cisco ACS description for this error: "This maybe because of mismatched Shared Secrets."
The two Cisco ACS are synchronized so I should have same error on them...
Why does primary ACS generate this error?
Thanks for your help,
PatrickTarik Admani wrote:Amjad,That is a good observation, shouldnt 7.3 (which recently released) help put these types of issues to rest? I hear that the configuration can now be replicated from one controller to the next in a failover setup.Thanks,Tarik Admani
*Please rate helpful posts*
Yes. That is a good point.
With 7.3 you can use high availability (HA) between two WLCs and you can configure only one WLC (the primary) and all the configuraiotn can be replicated and synched to the other WLC (the secondary).
The two WLCs in the HA must be on same subnet though. Otherwise hot-standby HA between WLCs can't be used.
Rating useful replies is more useful than saying "Thank you" -
Cisco ACS for Unix authentication
My company is looking for a single sign on for all the windows and unix servers mainly for admins. I was wondering if Cisco ACS will work for this.
Basically the authentication will be all for the servers and routers ofcourse. I am thinking if I specifies windows AD in ACS config, Can I get the unix boxes to get authenticated against Radius?
Any help will be appreciated.
MannyHi,
Authentication of unix servers via ACS over radius protocol can be achiveable,check out the below link client end configuration needs to be done for radius authentication
Hope that helps out your query !!
http://www.ibm.com/developerworks/library/l-radius/
Regards
Ganesh.H -
Please help me configure authentic connection with Caller ID via ISDN 30B+D using Cisco ACS
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
Hi all
I have set up a dial up connection between to PC's at remote site and center. It using ISDN 30B+D which is configured on Router 3845. Currently I have configured authentic connection with username and password using Cisco ACS. To enhance the security configuration I want to authenticate both the phone number which dialup with Cisco ACS. And currently I have not done this. Please help me solve this problem.
Thanks so much
Longn1) I deleted bridge-utils, netcfg
2) I edited /etc/hostapd/hostapd.conf:
interface=wlan0
#bridge=br0
edited /etc/dnsmasq.conf:
interface=wlan0
dhcp-range=192.168.0.2,192.168.0.255,255.255.255.0,24h
and edited /etc/rc.local:
ifconfig wlan0 192.168.0.1 netmask 255.255.255.0
ifconfig wlan0 up
3) I added in autostart these daemons: hostapd, dnsmasq and iptables.
Profit! -
ACE 4700 and Cisco ACS aaa authentication
ACE version Software
loader: Version 0.95
system: Version A1(7b) [build 3.0(0)A1(7b)
Cisco ACS version 4.0.1
I am trying to authenticate admin users with AAA authentication for ACE management.
This is what I've done:
ACE-lab/Admin(config)# tacacs-server host 192.168.3.10 key 123456 port 49
warning: numeric key will not be encrypted
ACE-lab/Admin(config)# aaa group server tacacs+ cciesec
ACE-lab/Admin(config-tacacs+)# server ?
<A.B.C.D> TACACS+ server name
ACE-lab/Admin(config-tacacs+)# server 192.168.3.10
can not find the TACACS+ server
specified TACACS+ server not found, please configure it using tacacs-server host ... and then retry
ACE-lab/Admin(config-tacacs+)#
Why am I getting this error? I have full
connectivity between the ACE and the ACS
server. Furthermore, the ACS server
works fine with other Cisco IOS devices.
Please help. Thanks.Thanks. Now I have another problem. I CAN
log into the ACE via tacacs+ account(s).
However, I get error when I try going into
configuration mode:
ACE-lab login: ngx1
Password:
Cisco Application Control Software (ACSW)
TAC support: http://www.cisco.com/tac
Copyright (c) 1985-2007 by Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
ACE-lab/Admin# conf t
^
% invalid command detected at '^' marker.
ACE-lab/Admin#
The ngx1 account can access other Cisco
routers/switches just fine and can go into
enable mode just fine. Only issue on the ACE.
Any ideas? Thanks. -
Cisco ACS 4.2 and Radius authentication?
Hi,
I have a Cisco ACS 4.2 installed and using it to authenticate users that log on to switches using TACACS+, when I use local password database, everything is working. But if i try to use external database authentication using a windows 2008 radius server, I have problem that I can only use PAP, not CHAP. Anyone who know if it's possible to use CHAP with external radius authentication?To access network devices for administrative purpose, we have only three methods available :
[1] Telnet : Which uses PAP authentication protocol between client and the NAS device. So the communication between Client and NAS is unencrypted, and when this information flows from NAS to IAS server gets encrypted using the shared secret key configured on device/IAS server.
[2] SSH : Which uses public-key cryptography for encrypting information between client and the NAS device, i.e, information sent between client
and NAS is fully secure. And the communication between NAS and IAS is encrypted using shared secret same as above. Good point on SSH side is that commincation channel is secure all the time.Again the authentication type would remain same that is PAP.
[3] Console:Which is also the same it will not allow to use MSCHAP as there is no need to secure it as you laptop is connected directly to the NAS and then if you are using TACACS it will encrypt the payload .
Summarizing, we cannot use CHAP, MS-CHAP, MS-CHAP V2 for communication between client and NAS device or administrative access.
And the most secure way to administer a device is to use SSH.
Rgds, Jatin
Do rate helpful post~ -
Cisco ACS 5.2 authentication against multiple LDAP servers
Hi Folks,
I have a wireless network that uses ACS 5.2 to handle authentication. The ACS is integrated with an Active Directory LDAP server (my_ldap) and is working correctly at the moment. The authentication flow looks like this:
- User tries to associate to WLAN
- Authentication request is sent to ACS
- Service selection rule chooses an access-policy (wireless_access_policy)
- wireless_access_policy is configured to use my_ldap as identity source.
A sister company is about to move into our offices, and will need access to the same WLAN. Users in the sister company are members of a separate AD domain (sister_company_ldap). I would like to modify the wireless_access_policy so that when it receives an authentication request it will query both my_ldap and sister_company_ldap, and return a passed authentication if either attempt is successful. Is this possible?Assuming you're already authenticating using your AD binding and AD1 as your identity source, you can add a further LDAP server as another identity source and add this to your identity store sequence in your access policy to authenticate against both.
You can also add multiple LDAP servers and add them both to the identity store sequence (if you're not using AD1). -
Unable to generate reports in Cisco ACS 4.2
Hi All,
I have configured AAA on Firewall & i am successfully able to login into it using ACS username & password but unable to generate Accounting & Administration logs. Whenever i check either of these logs it shows me blank page. Below is the AAA config on Firewall.
I have installed Cisco ACS 4.2 on windows 2003 server.
aaa-server test protocol tacacs+
aaa-server test (inside) host X.X.X.X
key **********
no aaa authentication http console AAA LOCAL
aaa authentication http console test LOCAL
no aaa authentication ssh console AAA LOCAL
aaa authentication ssh console test LOCAL
aaa authentication telnet console test LOCAL
aaa authentication enable console test LOCAL
aaa accounting enable console test
aaa accounting ssh console test
aaa accounting telnet console test
aaa accounting command test
Awaiting for soln.
Thanks in advance.
Regards,
Amit.I had the same experience. I even reinstalled Remote Desktop on Leopard, which caused all the passwords and machines I had registered were hosed and I could build up the user/password database again.
Look in your console log. If you see something like:
Feb 12 10:55:22 dhcp46 [0x0-0x1a01a].com.apple.RemoteDesktopAgent[660]: IpcMemoryCreate: shmget(key=5433001, size=1466368, 03600) failed: Cannot allocate memory
It means that the postgresql database that is started for collection this information can startup. It will try several times, and then fail. The way to fix this
-Apple supplies their postgresql with some sensible memory settings for the trivial task they are asking postgresql to do
-increase the memory settings from the complete system. In Leopard you do that by creating a file called /etc/sysctl.conf
and add something like this:
kern.sysv.shmmax=167772160
kern.sysv.shmmin=1
kern.sysv.shmmni=32
kern.sysv.shmseg=8
kern.sysv.shmall=65536
See also:
http://forum.servoy.com/viewtopic.php?p=47461 -
hi,
I'm trying to setup a VPN solution, connecting to a 800 series router and authenticating off a Cisco ACS tacacs server.
I've basically followed the suggested config at http://www.cisco.com/en/US/customer/tech/tk59/technologies_configuration_example09186a00800a393b.shtml and the setup works fine if I use local authentication, but as soon as I switch to using TACACS the client authentication fails.
Debugging tacacs on the router i can see the requests being sent to the server, and the replies coming back - the login detail are definitely correct so I'm guessing that TACACS isn't authorising me to use VPN or IPSEC or something. But there is nothing in the ACS logs to suggest why I'm not getting through - no failed attempts are shown.
Any ideas?here is some debug from the router:
Feb 24 12:28:58.973 UTC: TPLUS: processing authentication start request id 129
Feb 24 12:28:58.973 UTC: TPLUS: Authentication start packet created for 129(vpngroup)
Feb 24 12:28:58.973 UTC: TPLUS: Using server 10.10.10.10
Feb 24 12:28:58.973 UTC: TPLUS(00000081)/0/NB_WAIT/823A9F04: Started 5 sec timeout
Feb 24 12:28:58.989 UTC: TPLUS(00000081)/0/NB_WAIT: socket event 2
Feb 24 12:28:58.989 UTC: T+: Version 192 (0xC0), type 1, seq 1, encryption 1
Feb 24 12:28:58.989 UTC: T+: session_id 1729330768 (0x67137E50), dlen 16 (0x10)
Feb 24 12:28:58.989 UTC: T+: type:AUTHEN/START, priv_lvl:1 action:LOGIN ascii
Feb 24 12:28:58.989 UTC: T+: svc:LOGIN user_len:8 port_len:0 (0x0) raddr_len:0 (0x0) data_len:0
Feb 24 12:28:58.989 UTC: T+: user: vpntest
Feb 24 12:28:58.989 UTC: T+: port:
Feb 24 12:28:58.989 UTC: T+: rem_addr:
Feb 24 12:28:58.989 UTC: T+: data:
Feb 24 12:28:58.989 UTC: T+: End Packet
Feb 24 12:28:58.989 UTC: TPLUS(00000081)/0/NB_WAIT: wrote entire 28 bytes request
Feb 24 12:28:58.993 UTC: TPLUS(00000081)/0/READ: socket event 1
Feb 24 12:28:58.993 UTC: TPLUS(00000081)/0/READ: Would block while reading
Feb 24 12:28:59.009 UTC: TPLUS(00000081)/0/READ: socket event 1
Feb 24 12:28:59.009 UTC: TPLUS(00000081)/0/READ: read entire 12 header bytes (expect 16 bytes data)
Feb 24 12:28:59.009 UTC: TPLUS(00000081)/0/READ: socket event 1
Feb 24 12:28:59.009 UTC: TPLUS(00000081)/0/READ: read entire 28 bytes response
Feb 24 12:28:59.009 UTC: T+: Version 192 (0xC0), type 1, seq 2, encryption 1
Feb 24 12:28:59.009 UTC: T+: session_id 1729330768 (0x67137E50), dlen 16 (0x10)
Feb 24 12:28:59.009 UTC: T+: AUTHEN/REPLY status:5 flags:0x1 msg_len:10, data_len:0
Feb 24 12:28:59.009 UTC: T+: msg: Password:
Feb 24 12:28:59.009 UTC: T+: data:
Feb 24 12:28:59.009 UTC: T+: End Packet
s9990-cr#
Feb 24 12:28:59.009 UTC: TPLUS(00000081)/0/823A9F04: Processing the reply packet
Feb 24 12:28:59.009 UTC: TPLUS: Received authen response status GET_PASSWORD (8)
"AUTHEN/REPLY status:5" is a permanent fail according to the TACACS RFC
In the VPN Client log it say "User does not provide any authentication data"
So to summarise:
-Same ACS server\router\username combination works fine for telnet access.
-VPN works fine with local authentication.
-No login failures showing in the ACS logs.
Maybe you are looking for
-
How can I get only the dual rows?
Dear gurus, I want to retrieve the rows that are dual in my SQL. select grb.num_matricula from gb_ficha_financ_assistido gff, gb_rubricas_previdencial grp, gb_recebedor_beneficio grb where gff.cd_rubrica = grp.cd_rubrica and (gff.cd_fundacao = grb.cd
-
Help: Can't get iTunes to work with VTBook from Village Tronic
After installing a Village Tronic VTBook display card into my windows laptop, iTunes will no longer recognize/sync with my 5th Gen iPod. Additionally, CPU useage gets maxed out between service.exe and iPodService.exe taking 98% CPU. When I uninstall
-
Convert simplified to traditional chinese
I have opened an epub in digital editions and it is showing up with simplified chinese font. Is there a setting to change the display to traditional chinese font?
-
I know the people behind this commercial " http://vimeo.com/7307911 " used xfrog and a couple of months to achieve this stunning result. There's a lot of tools out there to render out full grown trees, BUT is i possible to make a naturally , grow
-
Hi I am doing file - Xi-R/3 synchronous scenario . in that i used the wrapper RFC to send the Multiple materials to the BAPI ..in Mapping and when i tested the BAPI its working fine ... but the problem is File is not picking up and even i am not abl