New HDD Test and SMART Errors

I have two brand new Samsung Spinpoint F3 HD103SJ 1TB harddisks.  To check the drives before using them, I ran `badblocks -b4096 -w -s -v` on both drives.  No errors.
I then checked `smartctl -a`
The first disk has the following entry:
191 G-Sense_Error_Rate FLAG:0x0022 RAW_VALUE:1
The second disk has the following entry:
200 Multi_Zone_Error_Rate FLAG:0x002a RAW_VALUE:2
The raw values for both drives were 0 before I started the test.
The drives have just 15 power on hours.  Should I be concerned about the attribute error count?  Any suggestions on other tests to run to further check the reliability of the new drives?

Hi Dunsin,
Welcome to Lenovo Community!
As per the query we understood that you are facing issue smart test failed in your Laptop.
As the HDD is faulty you have to replace the hard drive take a data backup. Recovery disc is available in the service center, if the recovery is performed only the operating system is will be freshly installed but the data will be lost hence please take a data backup.
Best regards,                                                          
Ashwin. S
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Similar Messages

  • TS1424 Trying to download the new StarTrek film and get error 8008

    Trying to download the new StarTrek film and get error 8008. This is on paid and rent!

    Other people are getting the same problem with that film : https://discussions.apple.com/message/22872157#22872157
    You could try the 'report a problem' link to contact iTunes Support : http://reportaproblem.apple.com

  • Ran hardware test and found error code 4SNS/1/40000001:YPOR-0.592 ? can't find the signification of this error code

    ran hardware test and found error code 4SNS/1/40000001:YPOR-0.592 ? can't find the signification of this error code.

    Back atcha!

  • How could I restore everything in Firefox having new hdd replaced and Windows reinstalled?

    Due to some reasons (possibly boot sector problems/virus infection) my laptop (running Windows XP Pro) failed to boot up last week. I've replaced a new hdd and just have Windows reinstalled.
    The old hdd is in place and data on it is still accessible.
    Version of Firefox was 3.6.4 (continuously upgraded from 3.0 beta 2), with all defaults installed on the old hdd.
    Is it possible to restore everything (bookmarks, addons, history, preferences etc) in Firefox on the new hdd by copying files/folders from the old one? And what files/folders in specific?
    Thank you so much for help in advance.

    I was using another PC to post the question, please disregard the firefox version and plugins information above.

  • Can't watch Netflix on new Macbook Pro and getting error message.

    I recently got a new MacBook Pro and I am new to using Macs. I logged into Netflix and clicked on a movie but I get a message saying "An unknown error has occured". I tried setting up the device or whatever but where am I supposed to get the code? I tried the 6 numbers at the bottom of the site and nothing works. Am I supposed to download Silverlight for Netflix to work on this computer? As I've said before, I do not know anything about Macs and I am not computer savvy and I just need to know how to get Netflix going on this computer. I had searched on Google if Netflix could even be played on a Mac and it's my understanding that one is able to view Netflix on a Mac. Please help. Thanks.

    Nevermind I got it working. Not sure if it's possible to delete this thread. Let me know if it is.

  • Got a Screen named hardware teste and a error msg

    I was playing World of Warcraft,
    i went to sleep, turned the MBP off,
    when i woke up, i turned it on, a diffrent screen apeare named "Hardware Test"
    and give me an error MSG:
    4SNS/1/40000000:TGOD-86.500
    what that means?
    what should i do ?

    Call applecare or take it into an apple store. I got the same error message once, but without the 86.500 part, and ended up having to get my logic board replaced. Only those at apple know exactly what the error codes stand for though, so best to get in contact with them, and I would back up any important data just in case.
    -John

  • I tried to set up my new ipod shuffle and a error message popped up saying Ipod not found cannot update.  I can't sync my ipod now but it is showing on itunes.  What should I do?

    I bought a new 4th gen ipod shuffle and tried to sdet it up last night.  I installed the latest itunes software and started to sync my ipod, but error boxes kept popping up saying ipod not found cannot sync.  It was showing in itunes, then it would disappear, then it would come back.  I am not very good with computers so I don't know what to do.  Can someone help?

    Do you have an iCloud backup?  If you backed up your old phone to iCloud you can go to Settings>General>Reset>Erast All Content & Settings (which will erase your phone), then go back through the setup screens again and when prompted choose Restore From iCloud Backup.  However your backup won't contain everything in your iTunes library (such as your music) so you'll need to be able to sync with your computer unless you purchased everything from iTunes and want to redownload it to your phone.

  • Just restore a backup on a new apple imac and get error message 43 when trying to update creative cloud ... is there something to do to suppress the old imac and identify the new one ??

    I just move to a new imac following a crash.
    Is there something to do to suppress any trace from the old one in order to be able to install creative cloud on the new one ?
    I got an error when trying to update CC.
    Flo

    helps resolve installation problems for CS3 thru CS6 and for Creative Cloud
    http://helpx.adobe.com/creative-suite/kb/cs5-cleaner-tool-installation-problems.html

  • Sony's New HDD Cameras and FCE (or iMovie)

    Help! I just bought a new Sony camera that does not use tapes. It is the DCR-SR40. They files are saved as Quicktime, but I cannot use them in FCE. Sony support says that they are not compatible with Mac. I can buy an editing program from Pixela, for $100, but then I can't use FCE. Any help in getting the files to work? Any third party software to convert the files? Sony support said I could use an analog capture card, but again, another expense, and I lose the digital. Grr!

    Hey, thanks a bunch! I got Streamclip to work finally. I did have to d/l the quicktime add. I tried it without, to no avail. This twenty dollar fix is a lot better than the hundred dollar one.
    I tried to email you, but the forum wouldn't give me your address. Is there any difference to the export choices? Export to DV is the best choice? It worked with one dvd I just made. Since you have this camera, am I supposed to format the HDD drive before I use it? I did not, as I was in a hurry to film. I just grabbed it out of the box and shot. I seem to remember that I had to do that as well when I bought a still Sony camera a few years ago. Same problem, had to format to get the disk to read.
    Again, thanks a great deal for your help. I appreciate all here, both of you guys who helped me answer this problem.
    Best,
    LT

  • Trying to look Contents for a new custom InfoCube and giving ERRORS ?????

    Hi all,
        I have created a custom InfoCube (ZTEST_PS) in similar to 0PS_C04. When I try to look the Contents of this InfoCube through Manage --> Contents or Listcube Tcode option, it is giving the following warnings/errors for every attempt:
    1. Your user master record is not sufficiently maintained for object Company Code Hierarchy
    Diagnosis
    When checking your authorizations for object 'Company Code Hierarchy' (technical name: ZCOMPHIER) it was established that you do not have authorization in your user master record for this object (return code 12).
    Procedure
    How you continue depends on the return code. See the online documentation for ABAP language element "AUTHORITY-CHECK". Please note:
    With a return code of 12, the object 'Company Code Hierarchy' has not been maintained in the user master, meaning there is no profile in the user master record in which this authorization object has been entered. This is, however, absolutely necessary, as all of the authorization objects created in the development class RSR are validated in the 'and' link. If the authorization is missing for only one object, the request is rejected as unauthorized.
    Get the person responsible for your authorization to create you a profile containing authorization for object Company Code Hierarchy.
    2. System error: RSDRC / FORM AUTHORITY_CHECK USER NOT AUTHORIZED ZTEST_PS ZTEST_PS
    3. System error: RSDRC / FUNC RSDRC_BASIC_CUBE_DATA_GET ERROR IN RSDRC_BASIC_QUERY_DATA_GET ZTEST_PS 64
    Message no. DBMAN100
    4. System error: RSDRC / FORM DATA_GET ERROR IN RSDRC_BASIC_CUBE_DATA_GET ZTEST_PS 64
    When I try to run a query against this custom InfoCube, I am getting the same First Warning.
    How can I fix theses warnings/errors, PLEASE ?
    Thanks.

    Venkat,
    You dont have authorizations for the 'Company Code Hierarchy'ZCOMPHIER , you dont have authorizations.
    What you will have to do is ask the basis person to give you authorization for the Hierarchy , Or if you can ..switcg off authorization checks for the Cube in T-Code RSSM.
    Regards,

  • HP G62-b23SA - Imminent Hard drive failure - SMART Error (301)

    My HP G62-b23SA  reports a imminent hard disk failure. Hard disk test reports SMART Error (301).  Advised to back up the system and contact HP support to enquire if Hard disk  needs to be replaced or just needs repair. I have since backed up the system, should it be replaced?
    This question was solved.
    View Solution.

    Hi,
    The 301 Smart error would indicate that your Hard Drive is failing and will need to be replaced.
    If your notebook is still under warranty, contact HP and arrange to have the drive replaced.  You can check your warranty status Here.
    If you live in the US, contact HP Here.
    If you are in another part of the world, start Here.
    If you are out of warranty and would like a guide on replacing the Hard Drive yourself, please let me know - include the size ( ie 500Gb ) of your current HDD.
    Regards,
    DP-K
    ****Click the White thumb to say thanks****
    ****Please mark Accept As Solution if it solves your problem****
    ****I don't work for HP****
    Microsoft MVP - Windows Experience

  • Help.New HDD recovery of factory default hanged

    My Satellite M645-S110 Hard disk failed.I called Toshiba support and was advised to create a Recovery disk (4dvd) which I did and buy a new HDD. I bought and installed a new HDD (WD5000BPVT) and loaded the Recovery disk. It started the Recovery of Factory Default Software but failed on error in restoring PREINST10.WMM file. I tried this 2 more times and gave the same error. I assume the file was corrupted already when I created the recovery disk. So fortunately I have a set of recovery disc created when I first bought the laptop. This is what I have: 3 Recovery DVDs, 3 System Image dics, 1 System Repair disc, and 1 Windows Recovery Environment disc. 
    I loaded the no1 Recovery disc and the screen shows <Recovery of Factory Default Software> Preparing. Initiliazing the partition. Please wait...  so far I've been waiting for 4hours. Is there another way of recovering? Please help!
    Toshiba Satellite M645-S110
    Windows 7
    WD5000BPVT

    im having the same proplem with  my A205, the excact same proplem, but i havent recieved help with that issue yet, best of luck to you.

  • IMac G5 won't recognize new HDD restored from TM

    Hi All -
    Close to the finish line but can't cut through the ribbon -
    Received the gray screen with kernel panic dump - concluded HDD failure (no rotation). 
    Installed new HDD (2TB) and restored from TimeMachine (nice!).
    iMac would not recognize the HDD at boot - so I have been trying everything I can find in the discussions:
    Reset PRAM, Reset-all
    New PRAM battery
    Apple Hardware Test passes OK
    Disk Utility sees new HDD and formats/partitions OK (HFS Journaled)
    Power supply caps look good (main power supply was also rebuilt last month)
    Tried DiskWarrior - but it only gets so far before the grey screen and kernel panic (where this all began).
    With DiskUtility, I can see contents of the new HDD as restored by TM - just can't boot from it.
    Disk Utility was able to verify Disk - OK.
    I've run out of things to try -
    Looking for suggestions.

    I belive it was running 10.5.8 (my footer is out of date).  I would have upgraded further if not for the PPC limitation.
    I did use the original disk that came with the computer for the restore activity (which basically copied the TM to teh new internal HDD).
    Since the original disk (10.4) did not support TM, could that be the root of the disconnect?  If so, do I need to repeat the recovery with the 10.5 install disk?   

  • Sender mail adapter : no messages and no error log

    Hello,
    I have configured a sender mail adapter to read mails from the inbox. I have used IMAP protocol. URL is specified as imap://EMHBSEXM01/Inbox. User name and password is also specified properly. I have kept poll interval to 1 minute. Messages in the inbox are in unread status. But the mail is not getting processed. I do not see anything after 1 minute. I tried using generate fetch report flag. But even then it does not create any message in SXMB_MONI. I checked runtime workbench for Mail adapter but I do not see any message for the same. Is there something that I am missing?
    Thanks,
    Dev

    Hi All,
    I chekced your responses and tried accordingly. Our basis team has given me new link now and the error message has changed. I am getting following error message.
    exception caught during processing mail message; java.io.IOException: unexpected login response; read 001F BAD Command received in Invalid state.
    Does anyone have any idea what this error is?
    Thanks in advance,
    Devendra

  • Series link and Smart Series

    Until Sky stop prefixing programmes with the moniker NEW:, series link and Smart Series will not work because the planner thinks they are another programme.  E.g. last night UNDER THE DOME restarted, and was set in my Smart series.  Unsurprisingly, it did not record as the programme was called NEW: UNDER THE DOME.,...... Not technical, you can keep on rebuilding your planners all day, but the solution is obvious, except to Sky, no surprise there......

    The 'new' issue (which was fixed I think in R010) never stopped programs recordings, it just mixed up the stacks if you had episodes both with 'New' and without. This has been fixed in the majority of cases.
    Your issue appears to be entirely different. Did the next episode (ie last night's Falling Skies) appear in the Scheduled Tab at all and fail to record or didn't it put it in after last week's episode?
    is correct in that it is up to the channels themselves what constitutes a series. For example, it is the BBC who has decided that the new Top Gear specials being shown are not part of the aborted series, so Sky boxes won't have picked them up automatically.

Maybe you are looking for

  • LDAP Error 0x34=LDAP_UNAVAILABLE

    Hi, I am using Sun Iplanet Directory Server 5.2 and LDAP Version 3.0 to fetch records. The Problem currently i am facing is as follow I have made three conection to Iplanet Directory with same authentication level. Each connection apply diferent filt

  • Finally Closed setup control in Purchasing

    Hi All, Is there a way to disable users from "FINALLY CLOSING" PO's. If so what is the procedure to do that? Is that something done in workfloww???? Any Ideas? Thanks, Prathima

  • How to change check title from WACHOVIA to Wells Fargo

    Hi Friends, Where do I change to let our check header show different name of the bank? Thanks in advance, L

  • Error: oracle.jbo.NameClashException: JBO-25001:

    Hi, I am getting the error "JBO-25001: Name iterator of object type View Row Set Iterator already exist" when a button is clicked. The scenario is as follows A dialog page by invoking the OADialogPage class when a button (ArCmSubmit) is clicked. The

  • Did not find needed xsi:type attribute on element anyType

    The followings exception is thrown when using the access a web service using the proxy jar. The return xml contains <debts xm:bind="debts is return.safaccount.debts"> <anyType xm:multiple="debt in return.safaccount.debts">{debt}</anyType> </debts> de