No Wireless for the Weary!

I have a WRT54GL that was working fine until I had to replace my modem and then my desktop computer itself. When I attempted to sync the modem and router, no luck. I am able to follow the directions on the disk to step 9 where it asks for Advanced Settings. I called Comcast for this information and I was told that this should not be occurring. However, when I put in the recommended site anyway and the default password, I was told that there was no connection. I have contacted Linksys twice but I'm told that they can't reset my settings with me because my router has expired as of December. Basically the modem works fine directly connected to the desktop or wireless. However, I am unable to follow the steps on here because they rely on the modem actually connecting to the router and it's not. The router itself is working fine. I have done all of the obvious connections checks, etc. Help? Thanks!

I wrote that I did that already: I get all of the lights on the router when connected to the router but the modem light does not come on and I cannot launch any web browsers so I can't proceed. Could it be the modem even though it works directly with the computers?  Please offer another suggestion.  Thanks!

Similar Messages

  • Using a extender for my wireless for the iTouch

    I am looking for an extender for my wi-fi on the iTouch. I saw the Netgear WGXB102NA. Does anyone use this and does it work? I have the Linksys WRT54G. I have tried to go into the online setup, but it doesn't work. I have tried and tried. I know you can set up for repeater mode from there. I thought I would give this extender a try.

    Thanks for the input.
    I recently got a Netgear router because I did have problems with the wi-fi being spotty. I tried to access the online page to configure and update the firmware, but it didn't work. I still can't access my online configuration with the Netgear, but it's less spotty. I have tried many different things to power-cycling and etc, but I still can't get in there. Tech support can't figure it out either, unless I call them, and that will probably take two hours.

  • How do you set up the eprint for the photosmart 5514? asking for a proxy to print from the ipad?

    I have successfully set up my laptop to print wirelessly for the HP Photosmart 5514, but I am unable to print from my iPad.  The message that I receive when I select eprint is to enter my proxy.  Could you please tell me what step I must be missing?
    Thanks in advance for your help.

    Hi,
    Most likely your printer does not support AirPrint. But please check to see if your printer in the list:
    http://support.apple.com/kb/ht4356
    If YES, you can use this to fix
    iPad: http://www.apple.com/support/ipad/assistant/airpri​nt/
    If NO you have to print using other apps (if applicable) such as
       http://itunes.apple.com/au/app/hp-eprint-home-biz/​id299531647?mt=8
    More info from this:
       http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mob​ile/Cloud-Services-Supported-Printers-ePrint-Airpr​...
      http://h30434.www3.hp.com/t5/ePrint-Print-Apps-Mob​ile/Important-Information-for-ePrint-Home-amp-Biz-​...
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • I cannot add a Wi-Fi guest network. Gone to Utilities Airport Utilities and all get is an image/browser of my Airport Extreme. Looking for the browser which has the title Wireless but cannot find anywhere. I need help?

    I cannot add a Wi-Fi guest network. Gone to Utilities>Airport Utilities and all I get is an image/browser of my Airport Extreme. Looking for the browser window which has the title Wireless but cannot find anywhere. What am I doing wrong?

    Open AirPort Utility. The first screen looks something like this:
    Click on the AirPort Extreme and another screen will appear. Click Edit, then the window with the Wireless tab will appear.
    If you do not see these screens, you will need to start over and configure your AirPort again.

  • My Time Capsule has stopped backing up.  I have an Apple Time Capsule which backs up by wireless. For the last 3 days it has not backed up. I get this message: "The backup was not performed because an error occurred while copying files to the backup disk.

    My Time Capsule has stopped backing up.
    I have an Apple Time Capsule which backs up by wireless. For the last 3 days it has not backed up. I get this message:
    "The backup was not performed because an error occurred while copying files to the backup disk."
    I have gone into Mac Help and followed this down to stage 4:
    under shared it lists my time capsule and my husband's iMac - both use the time machine but we have switched his off temporarily.  Clicking on my Time capsule I get "Connected" and "Sharepoint" - I didn't have to enter connect or password
    I don't understand stage 5: how and where do I select the disk or volume that contains Time Machine backups ?  How do I know which it is? My disk utility lists 160.04 TOSHIBA MK... with sub-heading Macintosh HD.  It also lists (with a "CD" icon) HL-DT-ST DVDRW GS22N
    Under stage 6, how and where do I Locate your backup ? I try dragging my Time capsule from Finder to the Disk Utility side panel but it won't go.  What is my computer's name?
    Please someone help!  I'm completely stumped.
    Thanks,
    Maggie
    Mac Help says:
    If you back up to a Time Capsule or network disk:
    Open the Time Machine pane of System Preferences, and slide the switch to Off.
    Open Time Machine preferences
    Open Disk Utility, which is in the Utilities folder in the Applications folder. 
    Open Disk Utility
    Make sure the Time Capsule or network disk is turned on and available. 
    Open a Finder window, select your Time Capsule or network disk in the Shared section of the sidebar, and click Connect. If necessary, enter your user name and password. 
    On the Time Capsule or network disk, select the disk or volume that contains Time Machine backups. Depending on how your Time Capsule is set up, there may be one or more disks or volumes. 
    Locate your backup, and drag it to the Disk Utility sidebar.You can identify your backup by looking for your computer’s name in the backup’s filename.

    Hello,
    Thanks to the great Pondini...
    http://pondini.org/TM/C3.html

  • Using the Mac as a wireless Bridge for the Xbox 360

    Want to use your Mac essentially as a wireless adapter for an Xbox 360 or any console? plug in the ethernet cable between the two devices and follow the setup process!
    Wireless Bridge setup process
    1. Open system Preferences.
    2. Clisk sharing, then the internet tab and select Airport as the “share your connection from” then select the Built-in Ethernet in the list.
    3. Open up the terminal Application and type ifconfig en0 in the window it sohuld display an outcome like this
    ifconfig en0
    en0: flags=8863<UP,BROADCAST,SMART,RUNNING,SIMPLEX,MULTICAST> mtu 1500
    inet 192.168.2.1 netmask 0xffffff00 broadcast 192.168.2.255
    ether 00:16:cb:cc:80:aa
    media: autoselect status: inactive
    supported media: autoselect 10baseT/UTP <half-duplex> 10baseT/UTP <full-duplex> 10baseT/UTP <full-duplex,hw-loopback> 10baseT/UTP <full-duplex,flow-control> 100baseTX <half-duplex> 100baseTX <full-duplex> 100baseTX <full-duplex,hw-loopback> 100baseTX <full-duplex,flow-control> 1000baseT <full-duplex> 1000baseT <full-duplex,hw-loopback> 1000baseT <full-duplex,flow-control> none
    4. This gives you the information of what your computer’s IP address is. On the xbox dashboard in the network setup screen select manual and select the top section which contains the IP address, subnet mask, and Gateway address, for the IP address, input the Highlighted section above plus one, so its 192.168.2.1 (this is for standard configurations, again, just add one to the last digit of your IP address.
    5. Open Airport Admin Utility, the select configure on your airport. Then select the Internet tab This will give you your subnet Mask, input accordingly.
    6. For the Gateway address, you are going to put in the value in the blue box. This is because you are using your Computer as a gateway, therefor you need to tap into its connection.
    So For the Average setup you will use:
    IP Address: 192.168.2.2
    Subnet Mask: 255.255.255.0
    Gateway Address: 192.168.2.1
    7. Now for the DNS server, this varies according to What internet service you have, but, Airport admin utility provides the answer, right below the information we used above, you will see DNS Server. viola! Put that in as your primary DNS server in the second box of edit options in the network menu.
    Now you should be complete, test the connection and you should be Ready to Go!! Happy Gaming!

    Welcome to the discussions, DanSwiggsD!
    If you have a non-Apple device as your main router, unfortunately the AirPort Extreme has almost no chance of compatibility with your main router.
    If you do have an Apple router as your main device, please post back with your model number and we'll let you know how your devices should be configured.
    If you don't have an Apple device as your main router you have a few options to connect the xbox:
    1) A pair of ethernet powerline adapters could be used if you did not want to run a regular ethernet cable from your main router to the xbox.
    2) The new AirPort Express 802.11n model does have a feature called Proxy STA which should allow it to receive a wireless signal from any wireless router and allow the ethernet port to be enabled.
    Message was edited by: Bob Timmons

  • How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.

    How to set up Airport Extreme with Charter ARRIS Modem TM902A for the first time for WIRELESS.
    When Charter Tech goes to your site, have them connect the modem up, but do not connect the modem to your iMAC or MacBook Pro.  What you want to do is connect the Airport Extreme to the iMac or MacBook Pro first with the Ethernet Cable. You have to do this to configure via Airport Utility to set up the Base Station Name & Base Station Password.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple Tv, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.
    WHAT TO DO IF YOUR AIRPORT EXTREME WAS PREVIOUSLY SET UP FOR USE WITH ANOTHER CARRIERS ROUTER OR MODEM.
    NOTE:  If you already had your Airport Extreme connected for example, I previously had ATT Uverse and the Airport Extreme was connected to the Wireless Router Model 3801HGV, I disabled the Uverse Wireless and used the Airport Extreme for the Wireless signal in bridge mode, as the Airport extreme Signal is much stronger than the Uverse router, and I was able to obtain a Wireless signal with the Airport Extreme way much better with no signal loss which was very very frustrating with the Uverse router.
    Anyhow if you had it hooked up like this, now that you will be using it with the Charter ARRIS Modem TM902A, you will need to reset the Airport Extreme to clear out the old data it has in memory, with the previous set up otherwise it will not work. Trust me I spent 6 hours trying to make it work reading all Apple Support Community questions and answers relating to this type issue/problem others have been having trying to get their set up working. I tried all the tips, and I finally decided just to see if by chance I would be able to connect with someone with Charter Tech support who might be familiar with Apple to be able to assist me and by luck I did.  He told me why it was not working and was all due the previous configuration with the ATT Uverse router was still in memory with the Airport Extreme. Finally it was 10:30 PM when I decided to call Charter Tech Support and I had been working on this since 3:00 pm pacific. I did not call them earlier as all the post I read said they never received any good help from Charter. After calling them I finished up by 11:00 PM and was able to finally connect Apple Tv, iMac, iPhones and Macbook Pro. We love our Apple Product and Happy all is connected with the new
    Internet Provider Charter. I must say the speed is way way much better than it ever was with AT&T Uverse. 
    THIS IS WHAT YOU WILL NEED TO DO:
    First you will need to unplug the Airport Extreme, then by taking the tip of a pen or paper clip end you need to push the reset button on the back of the Airport Extreme and hold it
    down and at the same time plug the power cord back into the Airport Extreme count to 5 or 10 then release the reset button. Then once he light in front of the Airport Extreme stops blinking you need to plug the Ethernet cable from the Airport Extreme to your iMAC or Macbook Pro, and restart which ever one you have, then open the Airport Utility once it is back up.  If you see airport extreme pop up with the old network name or it shows and yellow triangle click on the Airport Extreme ICON it will not let you configure it but will ask if you want to get rid of it or remove and just do it.  Then Again restart your iMAC or MacBook Pro, open up Airport Utility again, and on the top left you should see under “Other Airport Base Stations” the MAC ID for the Airport Extreme.
    You will then create/configure a Wireless Network, create your Wireless Password that will be entered on each of your Devices, example, Apple TV, your iPhone, etc., you want to allow access to your Wireless Network you are creating.
    Wireless Security will be -> WPA/WPA2 personal or just WPA2
    Enter the Wireless Password you want
    Verify the Wireless Password (enter it again)
    After it is created you will see it on the Airport Utility window with the name you created for it and to the left, will be a Dot (circle that will be yellow).
    Next you then want to unplug the power to the Airport Extreme, and then take the end of the Ethernet cable you unplugged from the iMac or Lap top MacBook Pro and connect it to the back of the Modem.
    Next unplug the power cord from the modem and wait about 5 minutes, then plug the power back into the Arris Modem and wait until all lights come back on the modem wait
    about 5 minutes, then plug the power cord back to the Airport Extreme and you will see it the light blinking yellow.  Wait about 5 to 10 minutes, during this time Restart you IMAC or MacBook Pro, and once it is back up click on the Airport Utility and you should see on the Airport Utility screen.
    For INTERNET to the left the light should be green and you should see the Airport Extreme also appear and the light to the left on the screen should also be green.  If they are, you then should be able to click on the Wireless Symbol on top of bar of the screen and click to select the Wireless Network Name you created.
    If you Do Not See the light (Icon) next to INTERNET turn Green, or if you see the Internet Light Green, but the Light (Icon) next to the Airport Extreme is yellow, unplug the power again to the modem and unplug the power again to the Airport extreme and wait about 15 minutes or up to 30 minutes. Then plug the power cord back to the modem wait till all the lights light up then, plug the power cord back into the Airport Extreme and Restart your iMAC or MacBook Pro.
    The Airport Extreme light should change from yellow to green. Open up the Airport Utility to see what the indicators are showing they should both be green.  Again select Wireless network you created under the Wireless Icon on the top right of the screen. Open Safari and see if you are able to Route to a web page or the apple site should appear.

    I just got a Charter Modem. Model TM822. While I was moving, my Airport Extreme was still at my old place.
    I have a Linksys WRT320N I used for the initial Charter setup.
    I can get my Airport to work here, but the Internet light on the Modem flashes Yellow.
    Hasn't caused any issues so far but one thing I did notice.
    On the Linksys there were 3 DNS servers listed.
    The Airport Extreme only lists 2 and i don't see where I could add another, only change whats already there.
    I tried everything above, but light on modem still flashes yellow.
    I have the technicians cell phone. Told me "that shouldn't be" and gave the same advice listed above.
    I'll break down and call Charter one day, see if it's on their end. NSA tracking may need a reset LMAO.

  • HT4623 My iPod touch (4th gen) won't seem to get the iOS 7 update on its own. I've been updating it wirelessly for a while now but when I go through the settings to "software update", it searches but says "iOS 6.1.3, your software is up to date". HELP/Why

    My 4th gen iPod touch says iOS 6.1.3 is the latest version of software. I've been updating it wirelessly for a while so I know that isn't the problem &amp; I know I'm connected to the Internet; I typed &amp; submitted it on my iPod. Please help/explain why it's doing this!
    Also, my App Store also says I have an update but I don't. All my apps are up to date when I try to update... Why is that?

    That iPod touch model doesn't have enough RAM to run iOS 7.
    (90990)

  • I have an ipod touch 4g. I want to use our internet hdtv as a monitor so others can see my screen in 40". Sony guy said that can do it wirelessly through the internet router instead of Hdmi without the need for an apple tv.Is this true and how do I do it?

    As I said above, I want to view my iPod screen on our new 40" Sony Internet full HD TV.
    I know that you can do this via HDMI but a Sony guy said that you should be able to do this wirelessly by going through the router. Is this true and can I do this without the need for the Apple TV?
    We are soon going to get the airport extreme, so will it work with that?

    1. Is it a smart TV?
    2. If so.... Is the TV connected to the Internet?
    3. If it is.... Check if your iPod and your TV share the same IP address (Wi-Fi network)
    4. If they do.... Then you should go to wherever your "Other Media" tab is.
    5. After that.... Search for you iPod. Because it is connected to the same network, it should recognize the device they same way AirPrint does.
    6. If you happen to see this fail, then try this method:
    1. Do you have a Bluetooth-enabled computer/laptop?
    2. If so.... Enable the bluetooth on the computer/laptop as well as your iPod.
    3. After that.... Your iPod should be actively searching and it should find the computer/laptop.
    4. If it did.... Transfer the file onto Windows/Mac (preferably Mac) and find the program to open the file.
    5. After doing so.... Connect your computer/laptop to the TV via HDMI Output Cable.
    6. Now it should work!

  • Hi, I bouhgt a used Apple Power Mac G5, I want to buy a blue tooth card for the same to use wireless keyboard and mouse, i am just curious that why do i need to provide the serial number of my computer, is there any compatibilty issue?

    Hi, I am new in Apple Computer, I bought a used Power Mac G5. I want to buy a blue tooth card for the same to use wireless keyboard and mouse. so why it is mandatory to provide the serial number of the machine?

    Hello, Serial# not needed...
    At the Apple Icon at top left>About this Mac.
    Then click on More Info>Hardware and report this upto *but not including the Serial#*...
    Hardware Overview:
    Machine Name: Power Mac G5 Quad
    Machine Model: PowerMac11,2
    CPU Type: PowerPC G5 (1.1)
    Number Of CPUs: 4
    CPU Speed: 2.5 GHz
    L2 Cache (per CPU): 1 MB
    Memory: 10 GB
    Bus Speed: 1.25 GHz
    Boot ROM Version: 5.2.7f1

  • In hotel w/wireless network.  ATV finds network, but does not ask me for password, so can't communicate through network.  MacBook Air, iPad and 2 iPhones connected to hotel wireless, but ATV does not ask me for the password.  Any ideas?

    I have succesfully connected a MacBook Air, an iPad and two iPhones to the wireless network in this hotel.  Apple TV can see the network and "connects" to the network, but w/o asking for password.  I expected to see a screen immediately after selecting the network that asked me for the password as did all of my other devices.  ATV did not ask me for a password.  When I go to Settings>General>Network, it shows the name of the hotel wireless network, but I can't communicate with the network.  It can't set date and time.  When I try to enter my Apple account name and password, it tells me it can't log in w/o setting date and time.
    Any ideas on how to connect to this network?

    I am having the same problem. In my hotel when I connect my laptop a screen will pop up and you have to hit the button "I Accept Terms". However I can't do that with the ATV. I called the internet provider and they said they could not help me. Any ideas? Do you think the guy just doesn't know what he can do for me? I am thinking I will call later and hope to get a different technician who might know how to help connect me.

  • Is there a fix for the MBP wireless dropping issue?

    I began to experience the Macbook Pro dropping wireless connectivity on my very 1st Apple in 2008.  At the end of the day my machine was replaced with a new Macbook Pro mid 2010.  It appeared to be working just fine until about 2-3 months ago when I started dropping my wireless printer connection.  I searched the internet hoping for a driver update from HP or something from Apple and each time I found something, the problem still existed.  I even thought that by upgrading to Lion would resolve any issues that I have with my MBP wireless connectivity issue.  After upgrading to buying a new router, new printer and upgrading to Lion; the wireless dropping issue still remains unresolved!  I know there are several hundred in not thousands of people who are having the same problem so what are we supposed to do?
    When my 1st MBP was replaced in 2010 I had to stop working because I was diagnosed with "Failed Back Surgical Syndrome" and was in the process of applying for disability.  Something in the back of my mind said that I needed to purchase Apple Care for this new replacement however I had used all of my savings & retirement to sustain life for me and my family that there was nothing for Apple Care.  If it weren't for my church and family I am not sure what I would do during the 18 months of no income while waiting for a decision only to receive an appeal until I findly stood in front of an Administrative Law Judge who heard my case and granted me disability.  Besides there was no way I could ask anyone for money to purchase a warranty for a top of the line laptop while the country was falling off an economical cliff.
    I broke down and called Apple Support and was told that I qualified for technical assistance regarding the upgrade to Lion a few weeks ago.  The tech on the phone had me run some disk utility tests and had me repair permissions which she said could be the cause of the problem.  I willingly went along with her in hopes that this was indeed the fix.  However, within 10 minutes of hanging up the phone my MBP began to drop it's wireless connection to my new HP printer and also the Internet.  Hence my question above is what I am really looking to have answered!  What is the fix to this problem that so many people are having issues with?  I couldn't afford to purchase Apple Care back in 2010 and I can't afford to purchase a new 2011 machine today if that truly is the fix!
    I will be disabled for the remainder of my life and I have grown dependent upon my computer to stay in touch with friends and colleges from work.  I worked for the IT Group at Wynn Resorts and I can say that the type of service Appple is providing it's customers is not what I learned over the past 25 years with Mr. Wynn.  Why can't Apple get the simple concept that it's customers are it's life line and keeps them in business.  I need help and I don't know what to do nor where to turn.  It would be different if Apple acknowledged the issue and said they were working on it however they aren't.  I plead to Apple to help me fix my notebook so I can stay connected to the outside world vs. couped up inside my home.
    Best Regards,
    Scott Leavitt

    I am simply lookig for some help not an argument.  I am not an RF specialist however have setup a few wireless networks in my tenure at Wynn Resorts.  I fully agree that wireless networking is an art and a science however the powers that be in Network Land have toughted wireless networking is the easiest and quickest way to get two computers to talk with one another.  As I previously said I have already turned one (1) MBP in for this problem and Apple decided to replace it because they could not fix the problem with my particular MBP.  This MBP was running Leopard when the problems started
    I am having a hard time believeing that there are several other devicces in my home that depend on a wireless network to operate and my MBP is the only one having an issue.  I took this a step further and decided to see what would happen if I tried to connect wirelessly via Fusion.  In Windows 7 I am able to print and scan to my hearts content without any issues.  I am able to browse the internet as much as I want.  I close Fusion and try to connect to my printer via wireless and nothing.
    In order to get Apple to help do I need to get a Network Analyzer and capture packets when I have these problems?  Out of the 1000 + posts is there a consolidation of which answer is the best?  BTW I am accessing the internet via a wireless connection using Fusion and Windows 7.
    In response to Linc's comments, I will look at the router specifications however I did not qualify that these devices are not using the wireless connection at the same time.  Right now I would guess there are maybe two (2) or three (3) at the most that are actively transmitting / receiving information. --  Thanks

  • I have a macbook pro. i have a photosmart 7510. we just bought a new windows tower and the printer works wireless for us, but now the mac does not print anymore wirelessly. i keep getting a message Network host 'HPE93F2A.local.' is busy. what can i do to

    I have a macbook pro. i have a photosmart 7510. we just bought a new windows tower and the printer works wireless for us, but now the mac does not print anymore wirelessly. i keep getting a message Network host 'HPE93F2A.local.' is busy. what can i do to

    it is a windows 8

  • Firmware update for HP OfficeJet Pro 8000 wireless to fix load paper issue - as for the 8500?

    Is there any hope that that soon will be a firmware update to fix the issues loading paper and the printheads for the HP OfficeJet Pro 8000 wireless printer? 
    A month or two ago there came a firmware update to the HP OfficeJet Pro 8500 wireless, which has some of the same issues,
    and allegedly should have the much of the same load-mechanism as the 8000 printer.
    It would be great, as we are on the fourth (4) replacement of this HP 8000 printer. For example, it would be great if we could use normal (80g) paper and not has to use (HP) 90g paper, as this prevents us from using the duplexer and only print on one side.

    Thanks for the advice to contact HP tech support!
    I have tried in multiple ways since November 2009 to contact HP, when I got the first (of 4) printers. The first 3 printers was subsequently replaced.
    Finally in late June 2010 I got the message that there was coming an firmware update for Windows, but not for Mac's. The firmware should improve among other things the paper pick up (load paper issue) and the print-heads life.
    I have applied the Windows firmware on the printer from a pc, but still seems to have load-paper issues, even using HP Bright White paper, when printing from Mac's. I have not tested the printing from a pc, but assumes that a firmware upgrade the printer, and are not specific to a certain OS.

  • This is a workaround for the MBP wireless issue

    There have been many topics on the MBP wireless issues already, but I thought some people might find this workaround helpful.
    Firstly, my system is a 2.2Ghz MBP, running 10.4.10, and also airport extreme update 2007-04. I am using an airport express base station. My previous Powerbook never had any wireless problems, so I really couldn't blame the basestation for the MBPs poor wireless.
    Warning - The workaround requires a little bit of work in the terminal. A little bit of understanding of how networks work is assumed here as well. So it is probably not for everyone ...
    What I have observed - whenever the MBP loses connection, the airport basestation IP and MAC addresses are missing from the ARP table.
    - To view the ARP table, type (in a terminal window) arp -a.
    So, when the MBP wireless hangs, open up the terminal and type that in.
    Do a Cntrl-C if the arp command is hanging and not returning anything.
    In normal situations, a list of IP addresses and MAC addresses will show up.
    As others have already noted, clicking on the airport icon in the menubar, will magically bring the wireless back to life. When this happens, the ARP table also gets magically populated correctly. Coincidence? I think not!
    So, the workaround is to store a PERMANENT entry in the ARP table for the airport basestation IP and MAC address. In my case, I can use the Airport Utility software to confirm what the basestation IP and MAC addresses are (note MAC address = Airport ID in Airport Utility). I found the basestation IP=10.0.1.1 and the MAC=0:11:24:07:d7:f
    To create a permanent ARP table entry for my airport basestation, I opened up a terminal window, and did the following -
    1) login to my administrator account
    2) type in the following command sudo arp -s 10.0.1.1 0:11:24:7:d7:f
    3) type in my administrator password to authorise the change
    4) type in (to confirm the changes have been made) arp -a
    5) logout of my administrator account (from the terminal)
    Ever since I did this, my MBP wireless performance has been flawless.
    Note, if you shutdown or restart your computer, the arp entry disappears. This is ok for me as I hardly ever power down my MBP. As insurance I have added an account startup item to remind me to do the arp table entry.
    This workaround is great for me because I don't have a need to use multiple wireless networks. It might not be practical for people who roam around onto different networks.
    Give it a go and see if it works for you.
    Message was edited by: michael louey

    OK, after some further experimenting, I changed the multicast rate on my airport express. It was set at 6Mbps, and I changed it to 2Mbps.
    I have read that the default multicast rate for previous 802.11g versions of Airport basestations is actually 2mbps. Excellent results so far !! I have set up a terminal command to continuously ping my airport router address every 15 sec, and there have been virtually no dropped packets so far over many hours.
    ping -i 15 10.0.1.1
    Interestingly, in Apple's Airport Admin software in my MBP there is no option to set the rate at less than 6Mbps (!!!!), so I had to use the Windows XP version of Airport admin software to make this change using a windows machine. Using the XP software you can set the muticast rate as low as 1Mbps.
    If you are using Apples airport admin software (Tiger and Leopard) and you commit any sort of change in settings, the multicast rate will be re-set at a minimum of 6Mbps. My understanding of the multicast rate is that setting it too high is similar to shrinking the coverage area of the basestation, and limiting access only to clients who can transmit at the required multicast rate.
    So my new theory is that the dropouts are caused by the MBP dropping off the airport due to not being able to achieve the set multicast rate. (this could be due to factors such as low signal strength, excessive interference or noise).
    If you are using Apples more recent Airport admin software, you are having a minimum 6mbps muticast rate set, and this might be too high for your particular environment.
    Just a theory.
    (oh yeah, I enabled interference robustness on the MBP and the basestation just for good measure)

Maybe you are looking for