O' Sol O' Mio

I have a system that's great for video, but now I'm getting into animation and quickly discovering what 'real' render times are all about! just a little math: 1 frame renders approximately at 26 seconds. 30 frames per second X 60 seconds = 1800 frames X 26 seconds per frame = 46,800 seconds or 13 hours to render 1 minute of animation??? it's obvious that I can't dedicate my only computer to rendering full time, and am looking at the MacPro's. the iMac's don't have the expandability, and I'm wondering if it's better to run Windows (XP Pro for instance) on a Mac?
1.25ghz (former 450) Sawtooth Mac OS X (10.4.6) 2 GB Memory, 64 MB Video Card

thanks, Tom. the reason I was considering XP on a Mac is because it's ability to take advantage of 64-bit processing, whereas Mac's don't have the luxury of 64-bit software, as yet anyway. Leopard is coming, but with the jump Windows has with 64-bit in Cinema 4D, Lightwave, etc, and that my MacPro would be totally isolated from the Internet (I have a G4 to take care of that), and that it would be dedicated for animation (because of rendering), I was thinking it would be too advantageous to resist.

Similar Messages

Al mio iphone 4 nn funzionava il microfono,ieri ho sostituito il microfono con uno nuovo,ma ancora non funziona,qualcuno sa dirmi il motivo o cosa possa essere?

al mio iphone 4 nn funzionava il microfono,ieri ho sostituito il microfono con uno nuovo,ma ancora non funziona,qualcuno sa dirmi il motivo o cosa possa essere?

Anche io ho il tuo stesso problema, ma il mio iphone era già aggiornato al 4.3.3 - ho provato tutte le strade possibili pur di non mandare il dispositivo in assistenza, "anche perche il mio era praticamente immacolato senza nemmeno un graffietto" ho anche sostituito la sim perchè la vecchia era stata da me adattata con taglio manuale, ma inutilmente in quanto anche con la nuova non è cambiato nulla, adesso ho resettato tutto e ho fatto richiesta di intervento apple, cosa un pò strana e che mi fa pensare: il 24 agosto 2011 mi scade la garanzia di apple di soli 12 mesi (tutto da dire nella comunità europea) esattamente ad un mese dalla scadenza il primo problema prima finzionava tutto in modo egregio, per paura di rimanere fregato dalla garanzia di 12 mesi ho appena aquistato l'estensione a 24 mesi prima della scadenza al "modico prezzo di 78,48 euro comprensivo di spedizione e iva.
Che dire "i piaceri si pagano" però non credo sia corretto.....
Marco Toscano
[email protected]
iPhone 4, iOS 4.3.3
Message was edited by: mtoscano

Mi MacBook Pro se apaga sola aún estando cargarda

La Mac Book Pro se apaga sola aún estando cargada, se apaga la pantalla y se quedan las teclas prendidas, tengo que forzar el apagado y luego funciona normal, pero a veces la prendo y se apaga y lo hace varias veces, aí que decido dejarla apagada un rato.

El mio tambien pasa lo mismo pero en cuando da el aviso de poca bateria el 10% a los 9 se apaga, sabes como se soluciona?

Fotocamera iphone4 si chiude da sola

salve a tutti, da sabato ho un problema con il mio iphone4, quando scatto una foto, l'app si chiude da sola e non mi salva la foto.
se entro nell'app delle immagini, le foto recenti non ci sono e continuamente cambiano di posizione.
cosa devo fare?
ho provato il reset da telefono, il ripristino da backup... ma niente.....

anche io riscontro lo stesso problema con la fotocamera. Non lo fa sempre ma spesso si blocca dopo lo scatto e devo riavviarlo brutalmente.

Non riesco a scaricare le mie note presenti sull'iPhone nel mio iPod Touch

Ho delle note sul mio iPhone e volevo passare nell'iPod attraverso iCloud, ho attivato in tutti e due i dispositivi le note ma nel mio iPod non compare niente

La sola cosa disastrosa che leggo è il tuo commento.
In primis dovresti conoscere la differenza tra la garanzia legale del rivenditore e quella del produttore: nel caso di Apple la garanzia limitata di un anno va ad AGGIUNGERSI a quella legale del rivenditore.
Continuo:
-hai pagato per parlare con un numero verde? Il numero per l'assistenza è totalmente gratuito, quindi spiegami che numero hai chiamato.
-dici che l'iPad non funziona, però non aggiorni il sistema operativo perché la tua autorità si sostituisce a quella di chi lancia i nuovi aggiornamenti. E paghi per farti dire che iOS va aggiornato. Sei bravo.
-iOS 7 fa schifo? Deduco quanto poco sai utilizzare gli oggetti che hai acquistato al meglio delle loro potenzialità, figuriamoci se sei in grado di giudicarle.
Per il futuro ti consiglio di leggere i termini e le condizioni d'uso dei prodotti che acquisti.
Nel caso del tuo iPad avresti trovato tutto qui:
http://www.apple.com/legal/warranty/products/ipad-italian.html
avresti avuto così modo di informarti su cosa acquisti, anzichè lamentarti in seguito.
P.S. "Alterazioni del software"? Semplicemente i software si aggiornano, migliorano, cambiano.
Se non vuoi essere schiavo di alcun sistema operativo torna al Nokia 3330.

I am trying to download iTunes on my new desktop computer (Windows 7, 64 bit). It starts installing, and then stops with the message- "The System Administrator has set policies to prevent this installation." I am the sole user- please help.

I am trying to download iTunes on my new desktop computer (Windows 7, 64 bit). It starts installing, and then stops with the message- "The System Administrator has set policies to prevent this installation." This is a stand alone computer and I am the sole user.   Please help.

This is a Microsoft Windows Issue.
From a MS Support Engineer:
"Hi,
·        Is the computer on a domain?
·        Is the issue isolated to only this software or you get the same error message with other software’s as well?
Try the steps below and check if it helps.
Step 1:
Run the software setup file as an administrator and check if it helps.
a. Right click on the setup file of the software that you are trying to install.
b. Select “Run as administrator”.
Step 2:
Temporarily disable the antivirus software running on the computer and check if you are able to install the software.
Disable antivirus software
Warning:
Antivirus software can help protect your computer against viruses and other security threats. In most cases, you shouldn't disable your antivirus software. If you have to temporarily disable it to install other software, you should re-enable it as soon as you're done. If you're connected to the Internet or a network while your antivirus software is disabled, your computer is vulnerable to attacks.
Step 3:
a. Click Start, type "Local Security Policy" (without quotes) and press enter.
b. Click on Software Restriction Policies.
c. In the right pane, double click on the "enforcement".
d. Select “All users except local administrators”.
e. Click Ok and restart the computer and check if the issue is fixed."

New Nokia C5-03..need sol...

i bought nokia c5-03 on 14-5-11...i want to know sol for few things....
1.Hanging-whn i type msg and click add contact..it hangs...n if i try to edit any one pic from my gallary..again it hangs..either i hav to lock n lock or switch off it n on.. thn it vl work..one time even the lock key dint work...these all happened whn thr s no running app.hw to manage it..without hanging?
2.Whn i try to tak pic in cam..its coming in landscape mode..whn i turn potrait also the cam icons(to tak pic.A)r in landscape mode itself..the auto turn control is in ON only...the same thing whn viewing vidieos..clarity s not good to feel it as 5mp cam
3.whn i copy songs from pc to mobile using usb cable,in which folder(in memory card) it shld be added?so tht it vl automatically update in music player..i tried all possibilities but no result..tel me in which folder v hav to add those songs..
4.It s mentioned tht 2gb inbuilt memory card..but whn i recieved the mob its only 1.5gb..!!!!whr s rest .5 gb..?whn i scan memory its showing MIDP,SIS n other file occupied memory...wht r those app?
pls give me solutions....

try to download themes at nokia store..there where lot of themes there..

Problem with SUNWmdr and SUNWmdu in sol-9-u8-ga-sparc (9/05)

I'm jumpstarting a 280R with sol-9-u8-ga-sparc (9/05) and it's not installing SUNWmdr and SUNWmdu correctly.
The profile contains:
root_device c1t0d0s0
boot_device c1t0d0s0 update
partitioning explicit
filesys mirror c1t0d0s0 c1t1d0s0 15000 / logging
filesys mirror c1t0d0s1 c1t1d0s1 4096 swap
filesys mirror c1t0d0s6 c1t1d0s6 free /u00 logging
metadb c1t0d0s7
metadb c1t1d0s7
During the jumpstart the 280R displays:
- Selecting all disks
- Configuring boot device
- Configuring SVM State Database Replica on (c1t0d0s7)
- Configuring SVM State Database Replica on (c1t1d0s7)
- Configuring SVM Mirror Volume on / (c1t0d0s0)
- Configuring SVM Mirror Volume on (c1t1d0s0)
- Configuring SVM Mirror Volume on swap (c1t0d0s1)
- Configuring SVM Mirror Volume on SWAP_MIRROR (c1t1d0s1)
- Configuring SVM Mirror Volume on /u00 (c1t0d0s6)
- Configuring SVM Mirror Volume on (c1t1d0s6)
Verifying disk configuration
Verifying space allocation
- Total software size: 211.94 Mbytes
Preparing system for Solaris install
Configuring disk (c1t0d0)
- Creating Solaris disk label (VTOC)
Configuring disk (c1t1d0)
- Creating Solaris disk label (VTOC)
Creating and checking UFS file systems
- Creating / (c1t0d0s0)
- Creating /u00 (c1t0d0s6)
Creating SVM Meta Devices
- Creating SVM State Replica on disk c1t0d0s7
- Creating SVM State Replica on disk c1t1d0s7
- metadb: waiting on /etc/lvm/lock
- Creating SVM Mirror Volume d0 (/)
- Creating SVM Mirror Volume d10 (swap)
- Creating SVM Mirror Volume d20 (/u00)
Beginning Solaris software installation
so all appears ok but then it shows:
Completed software installation
Solaris 9 software installation partially failed
Solaris 9 packages partially installed
SUNWmdr
SUNWmdu
and then
Installation complete
- Creating SVM State Replica on disk c1t0d0s7
- Creating SVM State Replica on disk c1t1d0s7
- metadb: waiting on /etc/lvm/lock
- Creating SVM Mirror Volume d0 (/)
- Creating SVM Mirror Volume d10 (swap)
- Creating SVM Mirror Volume d20 (/u00)
- Making SVM Mirror Volume as boot device (/dev/md/dsk/d0)
- metaroot: acmifsqorc1-js: /a/etc/lvm/mddb.cf: No such file or directory
- cp: cannot create /a/etc/lvm/md.cf: No such file or directory
The system manages to boot but it's not using SVM.
SunOS Release 5.9 Version Generic_118558-11 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
configuring IPv4 interfaces: ce0.
Hostname: xxxxxxx
/dev/md/dsk/d10: No such device or address
Configuring /dev and /devices
The system is coming up. Please wait.
checking ufs filesystems
/dev/md/rdsk/d20: No such file or directory
Can't stat /dev/md/rdsk/d20
/dev/md/rdsk/d20: CAN'T CHECK FILE SYSTEM.
/dev/md/rdsk/d20: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
If I repeat the jumpstart with Solaris 9 (9/04) it works without any problems.
I found the same problem at
http://supportforum.sun.com/sunos/index.php?t=msg&th=131 3&rid=0
which says it's fixed in Solaris 9 (9/04). Is it possible that it's broken again in Solaris 9 (9/05)?

I'm jumpstarting a 280R with sol-9-u8-ga-sparc (9/05) and it's not installing SUNWmdr and SUNWmdu correctly.
The profile contains:
root_device c1t0d0s0
boot_device c1t0d0s0 update
partitioning explicit
filesys mirror c1t0d0s0 c1t1d0s0 15000 / logging
filesys mirror c1t0d0s1 c1t1d0s1 4096 swap
filesys mirror c1t0d0s6 c1t1d0s6 free /u00 logging
metadb c1t0d0s7
metadb c1t1d0s7
During the jumpstart the 280R displays:
- Selecting all disks
- Configuring boot device
- Configuring SVM State Database Replica on (c1t0d0s7)
- Configuring SVM State Database Replica on (c1t1d0s7)
- Configuring SVM Mirror Volume on / (c1t0d0s0)
- Configuring SVM Mirror Volume on (c1t1d0s0)
- Configuring SVM Mirror Volume on swap (c1t0d0s1)
- Configuring SVM Mirror Volume on SWAP_MIRROR (c1t1d0s1)
- Configuring SVM Mirror Volume on /u00 (c1t0d0s6)
- Configuring SVM Mirror Volume on (c1t1d0s6)
Verifying disk configuration
Verifying space allocation
- Total software size: 211.94 Mbytes
Preparing system for Solaris install
Configuring disk (c1t0d0)
- Creating Solaris disk label (VTOC)
Configuring disk (c1t1d0)
- Creating Solaris disk label (VTOC)
Creating and checking UFS file systems
- Creating / (c1t0d0s0)
- Creating /u00 (c1t0d0s6)
Creating SVM Meta Devices
- Creating SVM State Replica on disk c1t0d0s7
- Creating SVM State Replica on disk c1t1d0s7
- metadb: waiting on /etc/lvm/lock
- Creating SVM Mirror Volume d0 (/)
- Creating SVM Mirror Volume d10 (swap)
- Creating SVM Mirror Volume d20 (/u00)
Beginning Solaris software installation
so all appears ok but then it shows:
Completed software installation
Solaris 9 software installation partially failed
Solaris 9 packages partially installed
SUNWmdr
SUNWmdu
and then
Installation complete
- Creating SVM State Replica on disk c1t0d0s7
- Creating SVM State Replica on disk c1t1d0s7
- metadb: waiting on /etc/lvm/lock
- Creating SVM Mirror Volume d0 (/)
- Creating SVM Mirror Volume d10 (swap)
- Creating SVM Mirror Volume d20 (/u00)
- Making SVM Mirror Volume as boot device (/dev/md/dsk/d0)
- metaroot: acmifsqorc1-js: /a/etc/lvm/mddb.cf: No such file or directory
- cp: cannot create /a/etc/lvm/md.cf: No such file or directory
The system manages to boot but it's not using SVM.
SunOS Release 5.9 Version Generic_118558-11 64-bit
Copyright 1983-2003 Sun Microsystems, Inc. All rights reserved.
Use is subject to license terms.
configuring IPv4 interfaces: ce0.
Hostname: xxxxxxx
/dev/md/dsk/d10: No such device or address
Configuring /dev and /devices
The system is coming up. Please wait.
checking ufs filesystems
/dev/md/rdsk/d20: No such file or directory
Can't stat /dev/md/rdsk/d20
/dev/md/rdsk/d20: CAN'T CHECK FILE SYSTEM.
/dev/md/rdsk/d20: UNEXPECTED INCONSISTENCY; RUN fsck MANUALLY.
If I repeat the jumpstart with Solaris 9 (9/04) it works without any problems.
I found the same problem at
http://supportforum.sun.com/sunos/index.php?t=msg&th=131 3&rid=0
which says it's fixed in Solaris 9 (9/04). Is it possible that it's broken again in Solaris 9 (9/05)?

Data acquisition and generation with PCI-MIO-16E-4 card help!!!!

Hello,
I'm using a PCI-MIO-16E-4 card with labview7 (in using DAQmx)and I
would like to draw a frequency response.
My problem is: my program can run correctly in low frequency but, it
can't work correctly in high frequency (after 2KHz the signal is
false).
For verifying my program: I only try to generate and acquire a sweep
sine. I constate after 2KHz the sine I read dosn't resemble to a sine
I wrote.
Can you say me where is the problem?
Thank you.
Le Trong Thao.

"Dr. Imad" wrote in message news:<[email protected]>...
> my understanding is that you are generating a sine wave (on one of the
> anlogoutput channels) and you are trying to read the signal.
> Since you can verify the signal at low frequency, but not at high
> frequency, it looks like you should increase the scan rate of the data
> acquistion (if you can, set it to 10 times the signal frequency)
> You can also use an oscilloscope to verify the signal is what you
> really generated.
Thank you for your response.
I've tried to do it, and I've tried several other possibilities but it
doesn't work correctly.
In fact, I think the problem is in my program. Do you have a program
that works correctly? I f
ound examples in the help but they don't run
correctly.
Le Trong Thao.

How to do a single channel DAQ using NI-DAQ driver software with a PCI-MIO-16XE-10 card

Hi,
I would like to find out how I could do a simple one channel Data Acquisition from a signal generator using the NI-DAQ driver software with a PCI-MIO-16XE-10 card.
I have written some test problem but even when the signal generator is turned on/off I get back some weird values.
Here is my code.
CString sFunctionName("");
double volt[OUTPUT_POINTS*2];
double out[OUTPUT_POINTS*2];
short timebase, ready, code, stopped;
unsigned short sampleInterval;
int i, status, count=0;
unsigned long update, points;
short* ai_buffer;
short output_ch_vector[16];
int local_ITERATIONS = 2;
SAFEARRAYBOUND bound[1];
double dataItem = 9.9;
long j;
long k;
double* pTheValues;
LPTSTR lpsz_ErrMsg;
// Initialise device
status = Init_DA_Brds (deviceNumber, deviceNumberCode)
Initializes the hardware and software states of a National Instruments
DAQ device to its default state and returns a numeric device code that
corresponds to the type of device initialized
Init_DA_Brds(DEVICE, &code);
// Check return code from Init_DA_Brds
Code return should be 204: PCI-MIO-16XE-10.
if (code < 0)
CString sError;
sError.Format("Code error: %d", code);
if (code == -1)
sError = sError + ": No device found";
LPTSTR lpsz = new TCHAR[sError.GetLength()+1];
_tcscpy(lpsz, sError);
AfxMessageBox(lpsz);
delete lpsz;
return S_FALSE;
// Allocate memory for analog output and input arrays
//ao_buffer = new short[OUTPUT_POINTS*2];
ai_buffer = new short[OUTPUT_POINTS];
// Set double-buffering
status = DAQ_DB_Config (deviceNumber, DBmode)
Enables or disables double-buffered DAQ operations.
status = DAQ_DB_Config(DEVICE, 1);
if (status < 0 )
sFunctionName = "DAQ_DB_Config";
goto TidyUp;
// Get the rate parameters
status = DAQ_Rate (rate, units, timebase, sampleInterval)
Converts a DAQ rate into the timebase and sample-interval
values needed to produce the rate you want.
status = DAQ_Rate(RATE, 0, &timebase, &sampleInterval);
if (status < 0 )
sFunctionName = "DAQ_Rate";
goto TidyUp;
// Setup scan
status = SCAN_Setup (deviceNumber, numChans, chanVector, gainVector)
Initializes circuitry for a scanned data acquisition operation.
Initialization includes storing a table of the channel sequence
and gain setting for each channel to be digitized
status = SCAN_Setup(DEVICE, 1, ai_channels, gain);
if (status < 0 )
sFunctionName = "SCAN_Setup";
goto TidyUp;
status = SCAN_Start (deviceNumber, buffer, count, sampTimebase,
sampInterval, scanTimebase, scanInterval)
Initiates a multiple-channel scanned data acquisition operation,
with or without interval scanning, and stores its input in an array
status = SCAN_Start(DEVICE, ai_buffer, OUTPUT_POINTS, timebase, sampleInterval, timebase, 1000);
if (status < 0 )
sFunctionName = "SCAN_Start";
goto TidyUp;
while(count < local_ITERATIONS)
// Check whether we are ready to input another half-buffer
status = DAQ_DB_HalfReady(DEVICE, &ready, &stopped);
if (status < 0 )
sFunctionName = "DAQ_DB_HalfReady";
goto TidyUp;
if (ready == 1)
status = DAQ_DB_Transfer(DEVICE, ai_buffer, &points, &stopped);
if (status < 0 )
sFunctionName = "DAQ_DB_Transfer";
goto TidyUp;
count++;
// Clear the analog input
status = DAQ_Clear (deviceNumber)
Cancels the current DAQ operation
(both single-channel and multiple-channel scanned) and reinitializes the DAQ circuitry.
status = DAQ_Clear(DEVICE);
if (status < 0 )
sFunctionName = "DAQ_Clear";
goto TidyUp;
status = SCAN_Demux (buffer, count, numChans, numMuxBrds)
Rearranges, or demultiplexes, data acquired by a SCAN operation
into row-major order, that is, each row of the array holding the
data corresponds to a scanned channel
status = SCAN_Demux(ai_buffer, OUTPUT_POINTS * 2, 2, 0);
if (status < 0 )
sFunctionName = "SCAN_Demux";
goto TidyUp;
//Convert binary values to voltages (Doesn't actually take a reading from board)
status = DAQ_VScale (deviceNumber, chan, gain, gainAdjust, offset, count, binArray, voltArray)
Converts the values of an array of acquired binary data and the gain setting for that data
to actual input voltages measured.
status = DAQ_VScale (1, 0, 1, 1.0, 0.0, OUTPUT_POINTS , ai_buffer, volt);
if (status < 0 )
sFunctionName = "DAQ_VScale";
goto TidyUp;

Hello,
Please take a look at lots of examples available at :
1. www.ni.com >> NI Developer Zone >> Development Library >> Measurement Hardware
2. C:\program files\national instruments\ni-daq\examples\visualc
Sincerely,
Sastry V.
Applications Engineer
National Instruments

How to generate a sinewave with at-mio-16de

I have an at-mio-16de Daq card. I want to generate a sine wave on the analog o/p. I believe that I would use the WFM_load function. I do not understand 1) how to load a buffer for this function and 2) what mode I am supposed to use. The modes in the help file all say the description is for the DAQArb 5411. I am using visual basic for my app.

There are a number of examples which ship with the NI-DAQ driver which perform an analog output using the WFM commands. If you installed support for Visual C or Visual Basic when you installed the NI-DAQ driver you will find examples in the \Program Files\National Instruments\NI-DAQ\Examples directory. You didn't mention what language you were using; however, if you look in the VisualC\ao subdirectory you will find manu examples which demonstrate generating a waveform from your device. Use these examples in conjunction with the NI-DAQ Function Reference Manual, which can be downloaded from http://www.ni.com/manuals, and you will be able to better understand what is happening in these examples.
Regards,
Justin Britten

How can I use a GPIB and AT-MIO-16L with a common NI-DAQ?

I'm using a GPIB card for recording data and a AT-MIO-16L for sending an analog output to my instrument. Earlier, both the devices (GPIB and AT-MIO-16L) were running correctly. Until I reformated my hard disk. Now I'm trying to install NI-DAQ 6.1.1 for AT-MIO-16L but that doesn't detect my GPIB card. On the other hand if I use NI 488.2 along with MAX 1.7 or MAX 2.2, I'm unable to use AT-MIO-16L. Is there a way I could get both my devices running on a common platform?

NI-DAQ is not supposed to detect your GPIB and NI-488 software will not detect your daq board. When you installed MAX, was this from a LabVIEW driver install CD that also put a new version of NI-DAQ on your pc. Open MAX and check your currently installed versions of NI-DAQ and NI-488. They should both be listed. If you have a new version of NI-DAQ than 6.1, you can uninstall the newer version and install 6.1.

AT-MIO-16E-10 Gate signal,how can i configure it as in input or as an output ?

Hi there ! I have AT-MIO-16E-10 board and i want to control a counter (the GPCTR0 counter of the bord) to count up depending on the gate signal.Now i have the following missunderstanding.I've read in the AT-MIO-16E-10 manual that the gate signal can be treated eather as an input or as an output.So i want to control my counter (to count up) until a signal that comes on my gate counter's entry changes his states from 1 to 0 (to reset the counter) and then when it changes his states back to 1 form 0 i.e a transition from 0 to 1 to start counting again from zero.Now here i have 2 questions : 1. How can i config the gate signal as an input signal (in the AT-MIO-16E-10 manual it sais that the signa
l can be treated as an input or output and it's known if i configure the port as an output and if i came with an external signal to the gate i can damage the board if the signal it's set to zero ) 2. What it's the default state of the gate signal ?
Any vi files would be very usefully,Thank you very much for reading this and i'll be waiting for your answers as quick as possible.

Antonios,
The shipping example VI Count Edges does what you describe.
>Quoted from VI Description
Count Edges (DAQ-STC).vi
DESCRIPTION:
This VI counts rising edges, using an STC based device (e.g.: E-series). The counter increments its event count everytime a pulse comes into its source input. A gate signal can be added such that if a low signal occurs on the gate, then the counter will pause (scroll the front panel left to access the gate settings). The current value of the counter is read continuously in the while loop, until the Stop button is clicked or an error occurs.
I/O CONNECTIONS:
Connect the gating signal, if any, to the gate input of the selected counter.
If you selected the Source Selection to be "PFI line", connect your event count base signal to the PFI line indicated by "Source PFI line number used". (If you selected "Internal Timebase", no source connection is necessary.)
NOTE: For actual I/O pin numbers, please refer to your hardware user manual.
INSTRUCTIONS:
1. Enter the device and counter you want use.
2. Make your Source selections, as desired.
3. Optional controls are located on the left side of the front panel. You will have to use your scroll bar to reach these.
4. Connect your signals as described below in I/O CONNECTIONS.
5. Run the VI.
>End quote
If you look inside the Diagram of the Count Edges VI you will see a subVI, Group Config CTR, that has a constant set to "simple event counting." This configures the gate in the correct manner. You have 17 or so options to choose from (right-click to see the other choices). Each choice configures the counters as needed. No special effort is needed on your part.
If you really must know more details double-click on the Group Config CTR icon. On the Diagram of that VI is a Call Library function. Right-Click that and see more ugly details that you don't need to know. The functions of the counters are fully implemented by the options already available, so you don't need to know how the details, but it is intersting.
Hints:
Keep in mind that the counters require TTL level signals. 0V to 5V. Limit the current to the level the DAQ board can handle. You will false trip the counter if your low is higher than 0.8V. I have had problems with this when using noisy signals.
Also make sure you debounce any switches you wire to the counters. It is instructive to hook up an unbounced switch to the counter inputs and see just how many false trips they can generate!
Mike

AT-MIO-16XE-50 device is not responding to the selected base address

I'm trying to install my AT-MIO-16XE-50 DAQ board onto my Windows NT desktop computer, but I'm having trouble.
Here's what I've done: I've installed LabView 5.1 and the NIDAQ 7.0 software onto my computer first. Then I've physically installed the DAQ board into my computer. After starting the computer, the plug-and-play system seems to recognize the new hardware and install drivers for it. It then says I need to reboot the computer, so I reboot the computer.
When I then look at my device manager, it lists AT-MIO-16XE-50 twice. Under the properties/resources tab, one of them lists "input/output range", "interrupt request", "direct memory access", and "direct memory access" (i.e., 2 "direct memory access"s). The second one only lists "direct memory access" once and nothing else under the properties/resources tab. Also, the first one says that it is working properly while the second one says that it is not working properly (Code 10). I've played around with chaging the "direct
memory access" numbers and after rebooting the computer have gotten both AT-MIO-16XE-50's in the device manager to say that they're working properly. So, now the DAQ board appears to be installed correctly, because the device manager reports no problems with it. However, there are still 2 of them. My first question is this: should there be only 1 entry in the device manager list, or are there supposed to be the 2 that I see? The entries do appear to be different from each other, but they're for the same device, so that's a little confusing.
When I open my Measurement and Automation explorer, only one AT-MIO-16XE-50 device is listed (so this looks good), and under "properties" all 3 "direct memory access" numbers are listed. So, this all seems good. But, when I click on "test resources" or "test panel", I get an error message saying that "the device is not responding to the selected base address". Considering that this device was plug-and-play, and I did not set the base address manually, I don't understand why I'm getting this error message.
What I've tried is to change the "input/output range" number by using the device manager. I've tried a few different settings (rebooting the computer after each change) and none of the different "input/output range" settings seem to work.
I'd appreciate it if you could give me any help on figuring out how to resolve this "not responding to base address" problem. The info on your web site
appears to suggest flipping dip-switches on the DAQ card, but my card does not have any dip switches because it is plug-and-play. So, right now I'm
clueless! Thanks for reading this, and I hope that you have more insight than I do.

Smaria,
The AT-MIO-16XE-50 shows up twice in the Device Manager because it reserves three DMA channels, and the ISA bus only allows two DMA channels per ISA slot. You mentioned that you were able to get both devices working properly in the Device Manager. Below is a link to a KnowledgeBase that describes the proper procedure to successfully accomplish this. You should verify that this is the procedure you followed:
Exclamation Mark Appears with Error Code 10 on Windows XP/2000/98 After Installing AT-MIO-16E-10
Spencer S.

Error while copy document in Sol Man

Dear friends,
I am working in Sol Man 4.0.
I have loaded the doc 'ABC" in SOLAR02. Now i want to copy the document in RMAMAIN using the option
"Assign Document" ---L> as a copy, i am getting the following error
"FOLDER CLASS IWB4FOLDER is NOT valid for objects of info object class SOLARGEN"
Please guide to solve this..
Regards
Kumar

Also have a look at the following notes:-
=> Note 26050 - FIPP:Posting not poss. (SAPMF05A,0700,batch input)
=> Note 800177 - FB01: No batch input data for SAPMF05A 0700
thanks
G. Lakshmipathi

O' Sol O' Mio

Similar Messages

Maybe you are looking for