Odd Overheating Problem w/ Neo4-F

I just recently got all the parts for my girlfriend's birthday present but I'm having an odd overheating problem that is only happening on the CPU.
MSI Neo4-F
AMD 64 3200+ Venice w/ stock HSF and thermal grease
Geforce 6800GS
Thermaltake Soprano case
Thermaltake 430w PSU
2GB Corsair Value DDR ram
Seagate 160gb SATAII HDD
Windows XP Home
I built the PC no problem, hooked it up, it POSTs on the first try.  I install and update Windows, install drivers, DirectX, and install City of Villains to see how it runs.  It looks great, no stuttering, but after couple of minutes the PC just turns off.  I turn it back on, go into the BIOS, and the CPU temp is in the high 40s.  I download Prime95 and Core Center to check out the temps during load.
My CPU temp goes up about 1C/second until it slows down before 60C, and when it finally reaches 60C, it shuts down.  All other sensors stay in the 30s.  I put my hand up to the HSF after the shutdown and it was barely warm.  I can barely feel any heat in the entire case.
I flashed the BIOS to the latest, no luck, it doesn't help.  I reseat the HSF, doesn't help.  Tried different Cool 'n Quiet, no change.  I'm out of ideas.  Does anyone know what it might be?

Quote from: MurdoK on 13-January-06, 17:39:24
Hello !!
Try the following:
Doublecheck if your Heatsink sits properly on the Cpu and the thermal grease is applied correctly. Otherwise you could fry you CPU.
Plug out Power Cable from PSU, and push Power On Button for 5sec. The Power On Led should light up.Open PC Case, then replug Power Cable and start the PC. Go into Bios Setup and search under PC Health Options for "Cpu Temperature Shutdown". Set it to the highest possible value.
Check again if you have such high temps. If your Heatsink doesn´t get warm, but the CPU does, this is an indication for poor thermal heat transfer from CPU to Heatsink 
Greetz MurdoK
I see no option in my BIOS to up the CPU Temp Shutdown.  I don't know why the thermal grease would be applied incorrectly, the square of it on the HSF didn't get touched before landing ontop of the CPU.  I also removed and reseated the HSF to make sure it was on correctly.
Quote from: Stick on 13-January-06, 18:07:21
check if you have removed the plastic cover from the bottom of the HSF. happened before 
Definitely got the plastic off.

Similar Messages

  • CPU Overheating problem on Windows 8.1 Pro (installed with BootCamp)

    There is a really important overheating problem on windows 8.1 (installed with bootcamp) even i do nothing Cpu is 50-60-70 Celcius degrees. This is really annoying problem. Most of users necessarily need windows OS for using third part programs that doesnt exist on OS X platform. I think this problem is important and has to be fixed as soon as possible.
    My brand new Mac:
    MacBook Pro (Retina, 15-inch, Mid 2014)
    2,5 GHz Intel Core i7
    16 GB 1600 MHz DDR3

    I have the same problem on macbook pro retina 15 late 2013 - top configuration

  • I am using Firefox 3.6.8. Oddly, my problem appeared a few hours PRIOR to Firefox automatically installing the latest updates (the week ending 7/23), not afterwards. The problem is this: the browser continues to display tabs, the reload/home/history/favor

    I am using Firefox 3.6.8. Oddly, my problem appeared a few hours PRIOR to Firefox automatically installing the latest updates (the week ending 7/23), not afterwards. The problem is this: the browser continues to display tabs, the reload/home/history/favorites icons, URL field and Google search field while in full-screen mode, so it's not really full-screen anymore. How can I correct this?
    == This happened ==
    Every time Firefox opened
    == Oddly, my problem appeared a few hours PRIOR to Firefox automatically installing the latest updates (the week ending 7/23), not afterwards.

    Do you have that problem when running in the Firefox SafeMode?
    [http://support.mozilla.com/en-US/kb/Safe+Mode]
    ''Don't select anything right now, just use "Continue in SafeMode."''
    If not, see this:
    [http://support.mozilla.com/en-US/kb/troubleshooting+extensions+and+themes]

  • Macbook Pro overheating problems.

    I am running OS X Lion on my Macbook pro (late 2008) and it has been over heating for the past 2 months. I noticed that it was getting warmer than usual initially but now it gets too hot it comes up with the grey screen and forces me to do a manual shutdown. I can't even turn it on immediately because I think the it's so hot the pre-boot up check realises it's so hot for it to be start. I get 2 beep sounds and a pause whenever I try and turn it on after a forced shut down. I normally have to wait for it to cool down before I can turn it on again. I have tried cleaning the fans but that did not help. I should take it to the Apple Store but I don't want to give away my laptop for a week or so hence why I am trying to solve it myself if it's possible. Any ideas? My guess is the heat sinks not being as effective as they used to be?
    Thanks,
    Omar

    about my experience in kernel panics, mbp 17 no boot, freezes etc etc, i would recommend an Apple Authorized Repair Center as soon as possible. there are many thing that can goes wrong. Gpu and Cpu becomes very hotter during normal usage and if there aren't some slowing down performaces, it seems normal. A couple of week ago my mbp 17 core 2 duo start to freeze sometimes. Sometimes very often. My first think is an overheating problem due to intense cpu and gpu works but after a while, i realized that is totally random. my mac can stay on in idle mode for hours and freeze as soon i open firefox or safari to load a youtube vid.... and vice versa. Smc gave me an illusion but if there's an hardware problem, soon or late, it occours again. to be honest, ear fans at 6200 rpm most of the time is kinda annoying and noisy. So i decide for the apple authorized repair center. they diagnose a faulty nvidia gpu and after replacing the whole logic board, my mbp seems brand new. it becomes hotter as a brand bew one but it's absolutely normal. it's a laptop..no cooling fan like many others but only 2 fan to extract hot air from inside to outside.... it have aluminum chassis and this work like a big cooling system.
    there are many little pieces on the logic board and a faulty one can be a problem. A broken thermal sensor or a broken diode can compromise some other pieces to work in the right way. So, don't waste your time searching  a band-aid to your problem.... take it to an official repair center.. they know how to solve your problem.... at least, they do a try :)

  • Does anyone know how to email apple re a overheating problem on a third generation ipod

      Does anyone know how to email apple re an overheating problem on a third generation ipod nano

    You don't email them.
    If you click on the Contact Us link at the bottom of this page, and every page at Apple for that matter, you would find a section that looks like this:
    Phone
    Use Express Lane to contact an expert at Apple Support for personalized and convenient support.
    Mac, iPhone, iPod and iPad customers within 90 days of ownership are eligible for complimentary phone support — one support incident per iPod and unlimited incidents per Mac, iPhone and iPad. Online technical support for Apple products is available beyond the initial 90 days.
    U.S. iPod, Mac and iPad technical support:
    (800) APL-CARE (800-275-2273)
    U.S. iPhone technical support:
    (800) MY-IPHONE (800-694-7466)
    Canada technical support:
    (800) 263-3394
    See all worldwide support telephone numbers

  • Ipad 4 overheating problem

    Got a Ipad 4 overheating problem when i had updated 6.1.3 IOS.

    Hello pradipingale,
    Thanks for using Apple Support Communities.
    For more information on this, take a look at:
    iOS devices: Keeping device within acceptable operating temperatures
    http://support.apple.com/kb/ht2101
    Best of luck,
    Mario

  • Servere overheating problems on my T500 =/

    i've been having overheating problems for about 2 month now, basically have had to keep tpfancontrol running to keep from shutting down, constantly 95c ish. goes up to 110c and than shuts down. I cannot even reinstall windows without significant issues. I've tried reseating the heatsink/clear dust/reapply thermal paste but it does not help at all. I haven't called warranty yet because I didnt want to have to send it in but I checked today and my warranty expired on the 8th on this month =[. any idea how much it would cost to repair? I'm hoping visa extended insurance will cover the repair costs

    there is probably a problem with the heat sink, you may need to get it changed. The heatsink contains several heat pipes which use a relative low boiling point fluids like acetone, where the heat of the cpu and GPU is carried away through the evaporation and condensation process. If the fluids in the heat pipe somehow leaked out, then the heat conduction from CPU or GPU to the fan, would be purely through conduction through the copper materials, which is insufficient, hence the high temperature in the CPU.
    The other possibility that the thermal grease between CPU/GPU between the copper heatsink is either too thick or insufficient, and there is large voids where the heat from the CPU can't be efficiently conducted between the CPU/GPU to the heat sink.
    So you must get warranty to look at it and change out the necessary part. 
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • GT60 2PC Dominator - Overheating problems

    Hey guys,
    I am getting desperate here. My 6months old Dominator has been lately suffering from massive overheating problems - 90C+ which happens after in a short while after launching any Dx11 game (but many Dx9 suffers from the same). I have tried two different cooling pads Zalman and now Cooler Master N-1 that has positional fans which I have moved underneath the GPU+CPU, but computer behaves like they are not there, so it is virtually no good at all.
    What happens when PC gets into overheated state is that game starts massively to stutters both audio and video in terms of freezing in and out in short intervals that even ensues in Wind when I close the application. I wanted to check out whether the thermal compound has not been reduced, but comp is still sealed and after 6months that seems rather suspicious.
    What do you recommend ? Are there any other cooling solutions for laptops other than ineffective cooling pads ??
    Cheers
    Mars

    Hi,
    What country do you live in? As in EU (at least as far as I am aware of) opening notebook for repasting (or adding RAM/HDD/SSD) is OK and doesn't void warranty. However if you prefer to hear an official statement, contact MSI. If you live else where, then opening very likely voids the warranty.
    >>How to contact MSI.<<
    At last you can RMA the notebook.

  • [GX620] MSI GX620 Overheating Problem

    Hello,
    I have a MSI GX620 laptop and it overheats all the time when playing games (World of Warcraft)
    When playing the laptop just randomly shuts down after playing for a while.
    I am using a USB cooler to get rid of it but it doesn't seem to help in any way.
    Can someone please help me to fix this overheating problem since it is very annoying and I just can't get rid of it.
    It's been good for a week and now it just happens to shut down very often.
    Thanks in Advance,
    Sam

    Please note that Arctic Silver is slightly conductive. If you're going to use this, be VERY sure not to spill any or that you don't use too much.
    If it does spill and gets in contact with the small pins around the core you might create a short circuit.
    I recommend the following best tested thermal pastes:
    -Prolimatech thermal compound
    -Tuniq TX-3
    -Arctic silver 5 (slightly conductive)
    -Arctic silver ceramique
    -Enermax (Dow Corning TC-5121)
    -Thermaltake thermal compound
    See here for more... http://www.hardwaresecrets.com/article/Thermal-Compound-Roundup-January-2012/1468/5

  • MSI GT70 Dominator Pro - overheating problems

    Hi all! I'm very interested in buying that notebook, but i've heard a lot about msi's overheating problems and it worries me. I am aware that gtx 880m requires a lot of cooling and i would like to know if those infamous overheating problems have been fixed ? i don't want to spend so much money on something that works for a month.... I play a lot and i am very demanding in this case, so i predict i'd be playing 4-5h/day on max settings. Will i have problems ? what to do to avoid it ?

    You know what?  I already buy it in china.  and it's really high temperature .
    For example. I play Call of duty 10, and no matter I open the full effect or normal effect , the temperature always can be 93C  .  I see the Weather temperature is only 20.  and If I'm play Batman:Original    full effect same problem, the 880m temperature is going to 90+ .I'm use normal effect and close the Physical , then the temperature on 82-85....
    I'm very confuse,  If the 880m very high temperature .... why use it on laptop.... because if always a high temperature, you really not  good feeling to play anything, because high temperature will let you laptop retired more fast.
    Any way I also buy a cooling pad, but looks like not any working....maybe that about the laptop inside design....
    well, I search on Internet about GT70 design, and I think maybe the original thermal paste not good. So I buy IC Diamond 7 Carat ICD7 ,but I'm not use it yet. because the MSI chinese customer service tell me if you change it or reload it , They do not offer the warranty........looks like a joke......then what now.....?  I don't know , some friend told me , it's fine to change the thermal paste, but I still warry,  and I'm not continue play the game anymore....because every time the temperature on 90C. I don't any desire to play.
    GT70 only 1 Fan for Radiating, not 2 like ROG or Alien, maybe that is a dead design.......
    So, these all true story, and if any one has any idea or any advice, please tell me . thanks.
    any way I just search the GT70 temperature problem and I in here join every one, so sorry for my bad English.

  • K9N SLI - Overheating problems

    I occasionally get some problems with components overheating.  I have Speedfan 4.37, (from www.almico.com), installed to monitor system temperatures and it gives 7 readings.  Can anyone tell me which components these names refer to so that I can narrow down where the problem originates :-
    Local;   temperature now 46C
    Remote;       temp 60C
    System;          temp 49C
    CPU, (presumably the Athlon 64X2 4800+ processor);      temp 52C
    AUX;              temp 51C
    Core;             temp 45C
    GPU, (I think this is the graphics card  which is an MSI NX7300GT).     temp 62C
    According to the almico website it is the mainboard manufacturer who decides which names to give to which component and they do not list this MoBo on their website.
    The above temperatures are sometimes quite a bit higher.
    I am not sure if removing the CPU, cleaning off the paste and adding some new heatsink paste will solve my problems as there seem to be so many components with high temperatures, and they all seem to increase at the same time when the beast decides to get too hot.  The overheating problem is intermittent and is partly solved by running my computer with the panels off, which I would prefer not to do.
    Any help appreciated,
    Viv

    Quote from: BuD_Sp3NcER on 16-March-09, 21:04:19
    I have the same board as my 2nd Rig, I found speedfan to be a bit off on the readings for the K9N SLi though. Using the Chart Feature in Speedfan you can determine what temps are represented after giving the macine a Full Load, especially gaming. The GPU will in most cases be the highest, The CPU will be the one that tapers down the chart rapidly after exiting a game, the Chipset/Mosfet Not sure exactly what it's reading will also drop but not as much & rapidly.
    Use coretemp for CPU. I remember being concerned about the readings so I modded the Chipset with a Coolermaster chipset cooler by simply Cable-Tying it to the existing heatpipe cooler + some compound thus not voiding any warranty. Sounds weird but It does work as it gets quite warm which means it's moving the heat off the CHIP itself. I MOD all my boards in this way 
    Now that I have installed the blower fan below my graphics card all of the temperatures are lower, which I hope will ensure that I get no more unexpected shutdowns.  Even if the Speedfan temperatures are not accurate, at least monitoring them will show if any are increasing, which is when problems could occur.  The suggestion about adding a Coolermaster is interesting, but I think I would prefer to just replace the CPU cooler as there is no warranty problem because I built the computer myself.
    Viv

  • Did Lenovo cripple my processor to fix an overheating problem? Screenshots included.

    I have an X61s which was suffering from a hot right palmrest and an overheating issue where the system would shut itself off after a few minutes of high CPU load. I sent the system in for depot repair. According to one of the Lenovo techs I spoke with today, they replaced the wireless card (known source of right palmrest heat) and a fan - but I'm beginning to think that's not all they did to solve the overheating problem, at least as far as it pertained to the CPU and the system shutting off.
    The CPU is a 1.6GHz processor. After the system was returned to me, I sensed that it was running slower than before. I performed a test using Orthos and the Intel Thermal Analysis Tool to monitor CPU frequency. Sure enough, as the attached image shows, even with the Power Profile set at High performance, the processor was maxing out at 1200MHz under full load, 75% of it's 1600MHz maximum.
    Screenshot
    I installed RightMark CPU Clock Utility, which includes a CPU frequency monitoring function. It too reported the CPU frequency at 1200MHz. HOWEVER, when I changed the RightMark profile to Maximal Performance, the CPU frequency did hit 1600MHz as shown by RightMark's monitor and Intel's Thermal Analysis Tool. Suspecting maybe this was just a reporting error and my CPU was actually running at 1600MHz despite Intel's tool saying 1200MHz, I tested each with Prime95's benchmark function.
    CPU Benchmark without RightMark (1.2GHz) - 1792K FFT length best time = 65.751
    CPU Benchmark with RightMark (1.6GHZ) - 1792K FFT length best time = 106.146 ms
    Clearly there is a real difference in speed here, not just a CPU frequency reporting discrepancy.
    Given the fact that RightMark is able to bypass the default processor settings, which is what allows you to use it to undervolt a processor, it's not a surprise to me that it would be able to run the processor at it's native maximum speed of 1.6Ghz, where otherwise my processor seems to be somehow limited to 1.2GHz regardless of which power profile I've selected: I've tried High Performance, Maximum Performance and others, and have verified that the maximum processor state in each is set to 100%, yet still the CPU frequency is at 1.2GHz.
    When I sent this machine in for repair, I removed the hard drive - so whatever the Lenovo Depot did (assuming that they did do something to my processor) could not have affected the OS or other software on my system. I did notice that RightMark seems to have "lost" it's previous settings, which may suggest that Lenovo replaced the CPU or motherboard and RightMark reset itself having detected a new processor.
    Note that BIOS settings are all set to enable Maximum Performance (though I believe Windows bypasses these settings anyway), SpeedStep enabled and the other key CPU setting enabled (which I forget right now and don't want to reboot to check my BIOS for the name).
    I've called and spoken with 3 different people at Lenovo about this and none were of any help other than suggesting I start a new case and have my laptop shipped back in - but before I do that, I want to get to the bottom of this. If Lenovo intentionally crippled my machine to "solve" a hardware problem - and without notifying me, no less, then I am far from a happy customer.
    So, please provide any input if you have any. Is it possible that Lenovo did something to either the CPU or the BIOS to limit the CPU speed to 1.2GHz? Or is this just a crazy conspiracy theory? Has anyone else had overheating issues and noticed their laptop running more slowly after it's been fixed?

    Hello kctopitz,
    please install your battery and plug in AC. Without battery, plugged into the wall, you´ll never reveive the full power.
    I would then suggest to measure the CPU clock with Everest, you can download it as a trial.
    Follow @LenovoForums on Twitter! Try the forum search, before first posting: Forum Search Option
    Please insert your type, model (not S/N) number and used OS in your posts.
    I´m a volunteer here using New X1 Carbon, ThinkPad Yoga, Yoga 11s, Yoga 13, T430s,T510, X220t, IdeaCentre B540.
    TIP: If your computer runs satisfactorily now, it may not be necessary to update the system.
     English Community       Deutsche Community       Comunidad en Español

  • Has your Macbook Air overheating problems been solved?

    Hi All,
    Has there been a solution to the Macbook Air overheating problem for you?
    I'm considering selling my MBA but want to see first if there has been any new updates on this issue.
    I have a Macbook Air with the specifications as follows:
    Model: MacBook Air 1.6GHz Intel Core 2 Duo
    Production year: 2008
    Production week: 15 (April)
    OS X Version 10.5.7
    Have had the computer for about a year now and it has been constantly overheating and becoming more or less unusable when doing so. Have been hoping upgrades to the software would solve this eventually but that does not seem to have happened.
    As I'm writing this room temperature is about 20 degrees celcius. Laptop sits on a table with power cable plugged in. Not running any external screen. There is no video streaming or music playing. Only the Firefox browser and a few more idle apps are active such as Mail and Skype (in the background). Even under these conditions the fan is currently running loud at 6100rpm and the Macbook Air is very hot underneath.
    CPU temperature is currently 54 degrees Celsius. Both cores seem to be active.
    Now, as an experiment I will head over to YouTube to watch a video and open up Microsoft Word in the background, a perfectly normal usage for a computer this new. This is what happens:
    The computer starts to become painfully slow. After for example clicking an item in the browser there is a 1-3 second delay before the click actually becomes effective. It's now so hot underneath that I would not want to keep it in my lap. It is hard to use the mouse pointer properly as it does not update in realtime, I have to assume where it will land based on my movements. When scrolling, the spinning wheel icon becomes active. Everything is now happening in slow motion.
    Video is lagging heavily. I can only see probably 1 out of every 10 frames or less of the video. All applications running are very slow. CPU temperature is now 64 degrees celsius. Fan is at 6200. Computer is now unusable for me. When I scroll a page in the browser it takes about 2-3 seconds before anything happens. Changing tabs takes 5-6 seconds after I click them. I will have to shut it down before re-starting and resuming work. When room temperature is even higher on a hot day needless to say everything gets a lot worse quicker.
    Is this normal for Macbook Air's? If that is the case they are more or less unusable for most types of normal 2009 year usage (video, audio, browsing, office work etc).
    What solutions have you found? Coolbook? Software/Firmware updates? Hardware changes? Please let me know if you have been able to make your MBA not overheat under normal usage.

    Hi Everybody,
    Thanks for your replies to start with.
    I have tried to install Coolbook now and has it running. When using 'throttling' and letting it change CPU speeds (I think..) the problem still remains. When watching a video or other demanding task the temperature goes way up. Running a CPUTest (small or big) gets CPU temperatures of up to 84-85 C. Fan of course at 6200rpm all the time.
    Right now, I have Coolbook set to 800Mhz and 0.9V. Apps running are Firefox, Skype, Mail and iTunes with no audio playing. CPU temperature at 56 c and fan speed (as usual) at 6200rpm. I can use the computer now. It is still lagging and not very fast at all. Sometimes text appear 1-2 seconds after I have written it on the keyboard.
    So Coolbook has made a difference for me, but only when putting the CPU speed down to 800MHz. I wouldn't call reducing the CPU speed to half a 'solution' though and will not keep that as a long term solution. Reducing voltages for higher CPU-speeds 0.9875V for 1600MHz does not work, it still heats up massively.
    Have used the MBA for the whole day today and can't recall a single time the fan has not been around 6200rpm except right after boot.
    Thanks for the tips on upgrading to 10.5.8. I will try that right away and let you know how it works out.
    Have also considered buying some cooling device but just as you say that feels like a bit of a last thing to resort to.
    I'm surprised Apple hasn't responded stronger to this. Had this happened in the car industry we would have seen thousands of cars being sent back to the garage to be fixed.
    If this only has to do with some specific production weeks then the right thing to do would be for Apple to let those people have their computers either fixed or replaced.

  • More iMac sleep and overheating problems - any ideas?

    My iMac is about 2.5 years old now. It was working fine until the power supply had problems and was replaced under warranty. It then had could not mount DVDs or CDs and that was replaced under warranty, at the same time it was performing really, really slow, and then give me the spinning beachball for few hours straight before I had to turn off the machine by holding down the power button. The technician ignored that problem and I got my computer back partially fixed; the DVD drive was replaced and in his limited testing the computer did not lock up so he returned it to me.
    After a few days of use I then took the computer back again and he agreed the motherboard had to be replaced.
    While waiting for the motherboard to be replaced, I had extraordinary faith that my computer would come back in perfect working order: I ordered Leopard.
    Before upgrading to Leopard I decided to back everything up using SuperDuper so I could restore if I had problems with the upgrade. As a new father I have tons of photos and my son's iWeb page that I could not risk losing. My previous hardware issues made me act more prudently; I was lucky to have done that.
    Unfortunately the old motherboard was replaced with one that had more problems; after a few days of light use I upgraded to Leopard and was greeted with immediate kernel panics (grey screen of death). I restored from SuperDuper backup and tried again: same problem.
    Since I have lots of stuff on my system I decided to do a clean install: problem solved. I then started importing and consolidating my iPhoto libraries from my old G4 tower and my old "backup" system. The machine would overheat go to sleep after only importing a few photos or give me the spinning beach ball while typing in mail (when it was the only program open).
    After researching the situation one the internet I realized that many people have similar problems and I ended up installing "Temperature Monitor" to find out the temperature of my computer. The reported temperature of my computer is regularly hovering between 76 C - 85 C (169F - 185F). If the machine is idle the temperature is still very warm at 64 C (147F). I reset the SMU but that did not have an effect. I then found out the diagnostic test of the 4th LED that would turn on if the machine detected a heating problem. This test is intrinsically flawed since it can only be done with the case open so the heat can easily escape to the room (note both fans do work).
    I then took the machine in to serviced again. The problem would be easily solved if I lived in the United States or Canada, but I live in El Salvador. The only Apple Certified Technician (at least for warranty repairs that I know of) may be a little tired of trying to fix my computer (I can sympathize with him as I am tired of having it needing to be fixed).
    I dropped off the machine and 2 weeks later (I have learned to be patient for parts to come to this country) I called for an update. It turns out my computer is "fine". I went to pick it up and he performed the 4th LED test in an air conditioned room (with an open case obviously), copied a few files, opened some problems and it worked fine in his limited testing in an air conditioned building. He also said Leopard may have caused some problems.
    I have no faith in that computer right now so everything I do is on my 8 year old G4 "Gigabit Ethernet" tower. I have upgraded the CPU twice from 400 MHz to 800 MHz and then to 1.3 GHz over the years and put in 768 Mb of ram (as an aside I just ordered 512 Mb more ram as it is now my primary computer to edit video).
    I have videotaped the computer acting incredibly unresponsive and slow and am exporting it (currently 277 more minutes for 15 minute video) and overheating. It did not "sleep" when I had chance to tape it, may try again later (currently restoring 10.4.11 backup on iMac so technician cannot blame a clean install of Leopard).
    I called AppleCare and they were supportive with my problems and I hope to take in the computer again soon.
    Exasperated in El Salvador . . .

    Strongly suggest that you contact/call Customer Relations.
    Relay to them what you stated in your post. With all those repairs, you may be entitled to a new iMac.
    Sorry, I do not know the phone number of Customer Relations in your country. You may need to contact AppleCare & ask firmly & politely to be transferred to CR.
    Good luck!

  • Odd marshalling problems with EJB 3.0 stateless session bean

    Hello,
    I began encountering marshalling exceptions when invoking methods on a previously functionining facade bean. The problem seems to be almost arbitrary, in that certain packages receive marshalling exceptions, while others do not (my main client started failing, but then I realized that a simple test class was still working, along with oddly JSFs that invoke that main client, which fails outside of that scope). Is there some config issue with stateless session beans (in 3.0) that I might be missing? There are no duplicate versions of these class; they have not been modified; they've been compiled with the current IDE. Any help would be appreciated. Thanks.
    full stack trace:
    com.evermind.reflect.UndeclaredExceptionTypeException: oracle.oc4j.rmi.OracleRemoteException
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
    oracle.oc4j.rmi.OracleRemoteException: Invocation error: java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:142)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
         Nested exception is:
    java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.EXCEPTION_ORIGINATES_FROM_THE_REMOTE_SERVER(RMICall.java:109)
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:128)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
    oracle.oc4j.rmi.OracleRemoteException: Invocation error: java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:142)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
         Nested exception is:
    java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.EXCEPTION_ORIGINATES_FROM_THE_REMOTE_SERVER(RMICall.java:109)
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:128)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)

    Hello,
    I began encountering marshalling exceptions when invoking methods on a previously functionining facade bean. The problem seems to be almost arbitrary, in that certain packages receive marshalling exceptions, while others do not (my main client started failing, but then I realized that a simple test class was still working, along with oddly JSFs that invoke that main client, which fails outside of that scope). Is there some config issue with stateless session beans (in 3.0) that I might be missing? There are no duplicate versions of these class; they have not been modified; they've been compiled with the current IDE. Any help would be appreciated. Thanks.
    full stack trace:
    com.evermind.reflect.UndeclaredExceptionTypeException: oracle.oc4j.rmi.OracleRemoteException
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
    oracle.oc4j.rmi.OracleRemoteException: Invocation error: java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:142)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
         Nested exception is:
    java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.EXCEPTION_ORIGINATES_FROM_THE_REMOTE_SERVER(RMICall.java:109)
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:128)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
    oracle.oc4j.rmi.OracleRemoteException: Invocation error: java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:142)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)
         Nested exception is:
    java.rmi.UnmarshalException: Error deserializing return-value: java.io.InvalidClassException: com.jwt.gui.menus.persistence.ViewRight; local class incompatible: stream classdesc serialVersionUID = 2365320765203750319, local class serialVersionUID = -8750611773395720631
         at com.evermind.server.rmi.RMICall.EXCEPTION_ORIGINATES_FROM_THE_REMOTE_SERVER(RMICall.java:109)
         at com.evermind.server.rmi.RMICall.throwRecordedException(RMICall.java:128)
         at com.evermind.server.rmi.RMIClientConnection.obtainRemoteMethodResponse(RMIClientConnection.java:472)
         at com.evermind.server.rmi.RMIClientConnection.invokeMethod(RMIClientConnection.java:416)
         at com.evermind.server.rmi.RemoteInvocationHandler.invoke(RemoteInvocationHandler.java:63)
         at com.evermind.server.rmi.RecoverableRemoteInvocationHandler.invoke(RecoverableRemoteInvocationHandler.java:28)
         at com.evermind.server.ejb.StatelessSessionRemoteInvocationHandler.invoke(StatelessSessionRemoteInvocationHandler.java:43)
         at __Proxy1.findAllViewRight(Unknown Source)
         at com.jwt.gui.menus.beans.ViewRightBean.<init>(ViewRightBean.java:34)
         at com.jwt.gui.menus.beans.ViewRightBean.main(ViewRightBean.java:63)

Maybe you are looking for

  • Save sitemap in Dreamweaver CS6

    I can see the site map in the site navigation map view but when try to save it by going to File/save site map, I never get a dialog box.  I have no idea if it is saving and if it is where.  I am trying to have Google crawl my site but the Google mana

  • Computer Not Recognizing my iPhone (iPhone Perfectly Normal)

    Hi, I have a macbook pro and an iPhone 3G. Out of nowhere, iTunes does not recognize my iPhone. I plug it directly into my computer, my iPhone vibrates and says it is getting charge, but iTunes does nothing. No error or anything, just does not show m

  • Export to CSV - order is now by alphabetical column

    I was using 1.2, and exporting to CSV, and the file was in table-layout order, so another app is able to import. Now with 1.5 the export is in alphabetical column-name order - and the other app can't handle it. Is there some setting to change the exp

  • Using || and && within the same Powerpivot Calculate syntax

    hi. i'm trying to isolate two groups of users. the 1st is a group who has suffered one of 3 "negative" experiences, without regarding whether or not they also had "positive" ones - i.e., they are the users from the entire population, who encountered

  • "multiple cursor in a procedure" is possible?

    Hi.. everyone. Is it possible , "multiple cursor in one procedure"? For example, create or replace procedure xxx is vAAA varchar2(10); vBBB varchar2(10); cursor cur_1 is select .............................; cursor cur_2 is select ...................