* OggPlayFonts make N82 (S60 v11. ) un-bootable *

I've found what caused my N82 to become unbootable.
(See my thread !!!My N82 refuses to boot / start !!!)
Now that the phone was set-set, and I've lost all my settings and apps I've installed, I've started with the last thing I did before phone got stuck in infinite loop on boot.
Last thing was I started install OggPlay, and started with OggPlayFonts, as per readme.
So I just did install it, and re-started the phone, per readme.
Bam, the phone is stuck again, in the loop, can't be switched off normally, and can't boot. So I have to re-set it again, this time not much to loose ...
I guess, if the phone's model is not listed as supported, one should not mess with that soft ...
But it does say that "This version of OggPlay should work on all Series 60 V3 phones, except for the Nokia E90"
(http://symbianoggplay.sourceforge.net/S60V3.html)
The packages I've tried are:
OggPlayS60V3_1_72
OggPlayFonts (came in same archive with OggPlay)
So no OggPlay for me on this phone... Hmm, i did not have any trouble on my ol' Nokia 9500

Similar Messages

  • How can I make the second internal drive bootable drive bootable for trouble shooting?

    I suspect that a newly installed SSD boot drive may be causing instability in my new 2012 Mac Mini Server. The logic board and RAM have been replaced and boot drive wiped and partitioned and 10.10.2 reinstalled. I'd like to make the second drive bootable in order to take the SSD boot drive out of the equation.
    Could some please describe the correct method for making the second internal drive bootable.
    Thanks.

    A quick addendum: your Mac will have a default boot drive set, and if not then it will choose the first one it identifies on the disk (usually the first partition on the first disk, followed by subsequent partitions on this disk, and then moving to the second identified disk, etc.). As a result, if you have to hold Option to select your second boot drive, the next time you restart, your Mac will boot back to the first drive. To make the second boot drive the default one, you will need to select it in the Startup Disk system preferences. This will update the hardware to use this as the default boot drive.

  • Partition Question:  Can I Make One HD Intel & PPC Bootable?

    Hello,
    I bought an OWC FireWire external drive to use as a bootable repair drive. My plan was to partition it in half and then make the first partition bootable on an Intel and then make the second partition bootable on PPC Macs.
    So, when I try to do this (via Disk Utility), I discover that I can't choose a partition scheme for each individual partition. Instead I have to choose one scheme for both partitions. GUID apparently boots Intel Macs and Apple Partition Map boots PPC Macs. Is there a way to do what I want to do, and if so, then how? Many thanks!

    Some confusion here. "I kept all of the drives as one partition" doesn't make any sense. You have partitions on a drive - not the other way round.
    •  Each partition of a drive is a separate volume with its own icon on the desktop.
    •  Every drive has partitions, even if only one! Another way of saying that is to say that no partitions means one partition.
    In Disk Utility if you select the drive, and not an indented volume beneath it, you will see the 'Partition' tab appear and in that tab you will see the "Options…" button which gives you the choice of partition scheme. That applies whether the drive has one partition (aka "no partitions"!) or multiple partitions.
    =-=-=-=-
    Your drives do not need to be re-zeroed. What you should do with all drives is occasionally (interpret that according to degree of carefulness /anxiety /paranoia)) run a 'surface scan' to check that no additional bad blocks have appeared, which is a warning to immediately get rid of that drive.

  • How do you make a new internal drive bootable?

    I have an early 2009 Mac Pro running 10.8.4, and just installed two new internal sata drives. I initialized them (Mac OX Extended (journaled). Are they now ready to install a system on (bootable)? I want to install 10.7 on one drive, and OSX 10.6.8 on the other. Other than the system, I want to keep them empty for now. I don't need files moved from the original drive with Mountain Lion. How do I accomplish this? Thanks.

    They are not bootable unless:
    Partitioned using GUID.
    Formatted Mac OS Extended, Journaled.
    Have a compatible version of OS X installed.
    Use your Snow Leopard DVD to install Snow Leopard. After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
    Upgrading from Snow Leopard to Lion or Mountain Lion
    You can upgrade to Mountain Lion from Lion or directly from Snow Leopard. Mountain Lion can be downloaded from the Mac App Store for $19.99.
    If you sign into the App Store and try to purchase Mountain Lion but the App Store says your computer is not compatible then you may still be able to upgrade to Lion per the following information.
    A. Upgrading to Mountain Lion
    To upgrade to Mountain Lion you must have Snow Leopard 10.6.8 or Lion installed. Purchase and download Mountain Lion from the App Store. Sign in using your Apple ID. Mountain Lion is $19.99 plus tax. The file is quite large, over 4 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
         OS X Mountain Lion - System Requirements
           Macs that can be upgraded to OS X Mountain Lion
             1. iMac (Mid 2007 or newer) - Model Identifier 7,1 or later
             2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) - Model Identifier 5,1 or later
             3. MacBook Pro (Mid/Late 2007 or newer) - Model Identifier 3,1 or later
             4. MacBook Air (Late 2008 or newer) - Model Identifier 2,1 or later
             5. Mac mini (Early 2009 or newer) - Model Identifier 3,1 or later
             6. Mac Pro (Early 2008 or newer) - Model Identifier 3,1 or later
             7. Xserve (Early 2009) - Model Identifier 3,1 or later
    To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
         Are my applications compatible?
             See App Compatibility Table - RoaringApps.
         For a complete How-To introduction from Apple see Upgrade to OS X Mountain Lion.
    B. Upgrading to Lion
    If your computer does not meet the requirements to install Mountain Lion, it may still meet the requirements to install Lion.
    You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax.  It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
         Lion System Requirements
           1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
               or Xeon processor
           2. 2GB of memory
           3. OS X v10.6.6 or later (v10.6.8 recommended)
           4. 7GB of available space
           5. Some features require an Apple ID; terms apply.

  • Change "Say Caller's Name" voice in N82 S60 3rd Ed...

    Hi,
    i would like to know if it is possible to change the default "Say Caller’s Name" voice to some other voice in my nokia n82?
    Please help.

    Hiiii !!!!
    I am also looking out for the same solution. They should allow us to select the language in similar way as the message reader.

  • BIOS Update for Thinkpad (x121e) in order to make Sandisk Cruzer Extreme finally bootable?

    Hello,
    will there every be a BIOS update for Thinkpads (in my case x121e) so that it (the BIOS of the thinkpad) will finally be able to recognize and therefore boot from usb flash drives / sticks like Sandisk Cruzer Extreme???
    (Once the OS is running, the drive is recognized just fine, but that's not what I'm here for.)
    My old desktop pc from 2006 has no problems with such a "modern" drive, but my 5 years younger x121e isn't able to boot from that drive? Come on, Lenovo, you can do better, at least you should...!
    I'm not sure, if that is the right place for such an inquiry, but as Lenovo apparently doesn't offer a proper support e.g. by email, I just try it this way. I once use the support by phone, only to find out that the lady on the other end had no clue whatsoever of computers and was just looking up answers in her system, which were, of course, not at all helpful.
    So, for now, this is my only hope, that someone from the technical team at Lenovo reads this and gets the BIOS programmers to work...
    Cheers,
    Mike
    [btw: I read about a similar entry where the guy finally marked his problem as solved just because he used another usb stick to boot the first one. That's not a solution, that's a work-around. I'm looking for a solution (= BIOS update), not a work-around!]

    Hi, I have an x120e and when I get into the BIOS > Startup > Boot, I see the following list:
    Boot Priority Order
    1. ATA HDD0 Samsung SSD 830 Series (my main disk)
    2. USB HDD SanDisk Cruzer Fit (a tiny usb drive that is always attached and holds assorted files)
    3. USB CD
    4. USB FDD
    5. PCI LAN
    The device can indeed boot from a USB stick. I think you will have to follow this order of events: first attach the USB you want to boot from, yet boot only from your main hard drive, to let the system recognize the attached USB drive and put it in the Boot Priority Order list, then shutdown, restart and get into BIOS. F1: to either to change the ordering in the list to put USB FDD or USB HDD SanDisk first) or F12 (I think): to choose a temp device to boot from. Or....... (another thought), the USB you want to boot from hasn't yet been made "bootable" (I think you may have to go into diskpart > etc to set it active) so isn't recognized in BIOS.
    I've used a USB flash drive with my recovery partition on it to restore to factory state. That was also a Sandisk Cruzer USB. I've also booted directly into a WinPE sort of environment using another bootable USB made for the purpose of restoring from system images. Mine is an x120e; your x121e can't be much different.
    Cheers!

  • How can I make a drive bootable without losing data on it?

    Is there a way to make a second internal drive bootable without losing the data that is already on it?
    The second drive was created under Panther 10.3.9. My main internal drive has had a clean install of Tiger 10.4.3. The second drive used to appear in the start up disk list when I was running 10.3.9 on the main drive. That is, it used to be bootable under 10.3.9. No kidding. After the main drive was given a clean install of Tiger, the second drive disappeared from the start up disk list. Please note: the second drive remains completely accessible when I am running off the main drive in 10.4.3. I can even use the few applications I had placed on the drive. It appears as separate drive under disk utility.
    I assume the second drive was installed as slave. (Both it and the main drive were independently bootable under 10.3.9.) It is not locked. "Ignore ownership" is not checked. The system has read-write privileges. Admin has read-write all others are read only. I am the only person who has access to this machine. It is not networked.
    I tried to ask this question a few days ago, but I think the way I phrased it confused the issue. My real question is NOT how did this get like this? It is can I make a drive bootable when it already has data on it?
    Thanks
    G4 Panther & Tiger   Mac OS X (10.4.3)  

    Hi,
    Thanks for your reply.
    You replied:
    the drive that you cannot
    boot from is a separate physical hard drive from the
    internal drive with 10.4.3. Is that correct?
    Yes.
    Have you used System Preferences > Startup Disk and
    looked to see if the 10.3.9 system shows up there?
    Yes, I have looked and it's not there.
    I got the impression that you have backed up the 10.3.9
    disk and that you do not really need the data there.
    Yes, I backed up a drive that was bootable, but then it lost its "bootabilty" and what I got was two non-bootable drives--the original second internal drive that I'm asking about and the back-up of it. I want the data on the drive and I wan the drive to be bootable.
    One thing that you might try when you are booted off
    your 10.4.3 system is to use Disk Utility, select the
    other disk and do a Repair Disk.
    Done that and it says there is no problem. Nada. Zero. It just won't boot, no more, no how, no way. BUT it remains fully accessible--I can access all my info. It's just become a storage drive that cannot be booted. Go figure.
    reformatting means
    destroying the data on the disk.
    Yup, which is why I asked my original question. Does anyone know if there is any way to make a drive bootable without destroying the data on it?
    I suspect the answer is no (given these particulars), but I thought some wise super-techie out there might have a trick up their sleeve.

  • What do I need to make a bootable external disk?

    I got a response from Apple support that said I could make an external disk a bootable one, like a flash drive or ext hard disk, by using an OS X Installer app that was supposed to be available at the Mac App Store.  I looked and couldn't find it.  Since we no longer get a hard-copy of the system install disk, I was trying to figure out what to do to make a 500Gb external disk one I could boot using the MacBook Air with its limited GB storage.
    So if anyone can give me the simple solution I'd appreciate it.

    Get an external disk drive. Start by partitioning and formatting it:
    Drive Partition and Format
    1. Open Disk Utility in your Utilities folder.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
    Next, clone your existing system disk to the external one:
    Clone Mavericks, Lion/Mountain Lion using Restore Option of Disk Utility
    Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
         1. Select Disk Utility from the main menu then press the Continue
             button.
         2. Select the destination volume from the left side list.
         3. Click on the Restore tab in the DU main window.
         4. Select the destination volume from the left side list and drag it
             to the Destination entry field.
         5. Select the source volume from the left side list and drag it to
             the Source entry field.
         6. Double-check you got it right, then click on the Restore button.
    Destination means the external backup drive. Source means the internal startup drive.
    Test the new clone by:
    Boot Using OPTION key:
      1. Restart the computer.
      2. Immediately after the chime press and hold down the
          "OPTION" key.
      3. Release the key when the boot manager appears.
      4. Select the external disk's icon.
      5. Click on the arrow button below the icon.

  • How to make any CUCM image, bootable image

    Como estas everyone
    I have non bootable CUCM image and i want to make it bootable
    Any help with this
    Thanks

    Hello,
    there are N number of software available for to make image from non-bootable to bootable
    http://brezular.com/2013/11/18/how-to-make-cisco-unified-communication-manager-bootable-iso-from-non-bootable-image-on-linux/
    Br,
    Nadeem

  • How to edit a time machine backup to make it bootable in single user mode

    I am away from home and do not have snow leopard install disk. My MacBook just keeps loading. I have my time machine backup and I was wondering if I could make my time machine backup bootable by deleting and editing files in single user mode and then booting from the external hard drive. I have already tried a lot of things like fsck and haven't gotten it to work so I thought all you command lovers could help me edit my time machine backup to make it bootable. Maybe I could somehow install applejack from the command line too?
    P.S. Right before it broke I restarted my computer and when it was turning off, There was a blue screen with a loading symbol and when it started to turn on it just kept loading with the apple symbol, if that helps you fix the problem.

    To begin with, there is no way to make a Time Machine backup bootable.
    You say you've tried a lot of things; does that include a safe mode boot? (hold down 'shift' during startup)
    I'm not myself familiar with Applejack, so you'll need someone else to confirm this, but I believe that it should be possible to install from the command line.

  • How to make a bootable hard drive

    I will be purchasing an external hard drive for my G5 for extra storage. Is it possible to make the second hard drive bootable without actually installing OS X on it? Is there a way to just install a system folder? Or can I just copy the OS X installer to that drive?
    I just want to be able to boot so I can run Disk Utility on the main drive when needed without having to use the startup DVD.

    Hello! You can also follow Kappy's suggestion below. Tom
    Kappy's step by step guide to ext cloning.
    This requires two steps and the external drive must be a Firewire drive:
    Prep external FW drive:
    1. Open Disk Utility from your Utilities folder.
    2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Click on the Partition tab in the DU main window.
    3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.
    Clone Using Restore Option of Disk Utility
    1. Open Disk Utility from the Utilities folder.
    2. Select the startup or source volume from the left side list.
    3. Click on the Restore tab in the DU main window.
    4. Drag the startup or source volume to the Source entry field.
    5. Select the backup or destination volume from the leftside list and drag it to the Destination entry field.
    6. Check the box to Erase Destination. Skip this step if you've already formatted the drive.
    7. Double-check you got it right, then click on the Restore button.

  • Can i make a bootable usb drive for os x yosemite on a windows pc?

    I have a Macbook Pro 13" 2009 that I've installed a new hard drive in.  How do I make an OS X Yosemite bootable USB drive (I have a 16 GB available)?  I'm traveling, so all I have with me is a Windows 8 laptop.  I have an iMac at home, so I expect I'll be able to do it easily there, but I have time now...  Thanks.

    No. You need a Mac for that.

  • Need to make an ISO bootable.

    Does anyone know of a free utililty that will make an ISO over 300MB bootable?  The only free ones I have found have  a limit of 300 MB.
    Thanks,
    Matt

    Sounds like someone is trying to make downloaded ISOs from CCO bootable.  Cisco doesn't support this at all.

  • Firmware Update on N82 - Software Updater Problem

    Hi
    This is my fisrt post to this forum but I have read a fair bit of the information already posted.
    I realise this question is asked frequently, but my problem seems to be a little different. Phone is N82 with V11 firmware and it is unbranded. Nokia site indicates V30 firmware available.
    Have loaded latest versions of Nokia PC Suite and Software Updater (several times!!).
    Software suite works OK for Map and Music stuff. But when I try to load the Software Updater software, the installation goes through the first stage OK and always hangs on the configuration stage. There is no Windows error message.
    I have to go into Windows Task Manager to kill the Software Updater application and then the PC will not shut down properly until I kill the nsl_host_process.exe application, - so this seems to be related to the problem.
    I am using Win XP SP2 (German) and have tried both the English and German versions of PC Suite and Software Updater, but problem is always the same.
    I have no Virus Checker or Firewall operating (except a Firewall on the Router, which I think will not affect this file). Internet connection and downloading are fine for all other operations.
    (I have tried to use another PC (Thinkpad) but unfortunately the Software Updater will not install here because in needs 256MB free RAM Memory.
    So, I am stuck at present, unless any of you knowledgeable folks have any ideas!
    Thanks
    Stonefish28

    Hy.
    Sorry but my english is not so fantastic.
    I have the same problem with my Vista, and now my Messanges dont work  and i can not make a syncronisation with my pc.
    I have tryd a lot but no resolution.
    thank you for your help.

  • Help with "No bootable Device -- Insert boot disk and press any key" problem

    Alright, I am on an Early 2011 17inch macbook pro.  I have removed the superdrive to install a secondary disk drive for mass storage, then replaced the original one with an SSD blah blah blah.  I do everything from the books, run bootcamp, make my USB windows 7 bootable in Bootcamp, go through everything and allocate 65gb towards windows.  I have tried 4 different USB sticks and 3 different ISOs.  Every time I try it, I get the same "No bootable device -- insert boot disk and press any key".  I then have to hold down the power button, then restart, hold down option/alt key, and boot regularly into mac.  I also read that holding option/alt whilst starting the macbook pro will show the windows USB stick, well it never appears.  I dont know what I need to do, what I am doing wrong, but nothing is working.  I guess the last thing I have to try is buying a superdrive and burning ISO to disc then try that.  But I dont want to go out and spend more money.  Other people have gotten it to work just fine from USB, I dont know what I must do or what I am doing wrong...
    Open to suggestions and in desperate need of help.  Anything is appreciated.
    Thanks!

    Don't bump
    get a new usb2 only flash drive and try the solution posted by kunu here and report back
    https://discussions.apple.com/thread/5105056?tstart=0
    How to install Bootcamp on a 2009 Macbook Pro that does not have a disc drive

Maybe you are looking for