Optimal gateway selection list

Group -
With in the AnyConnect profile, OGS can be enabled and deemed user controlable, however documentation speaks to an OGS list...where is this list defined? Is it the Server list or the backup server list? And if I have the server list defined, do I need to define the backup server list?
Thanks in advance

Hi Chris,
this is the Server list. You can, but do not need to define a backup list.
hth
Herbert

Similar Messages

Anyconnect optimized gateway selection question

Hello,
I am in the process of evaluating Cisco Anyconnect VPN for my company. Can anyone please let me know what will happen to the client if optimized selected gateway is full?
Thanks,
Deepak

Deepak,
I think I know what you are asking because I ran into this. If the gateway is available, running, and working but, for some reason you cannot connect, anyconnect will not try the backup list. Some examples where the gateway is reachable but might not connect might be you run out of licenses, DAP policies are denying you, gateway misconfigure, gateway hung etc. In this case, I don't think AnyConnect will attempt to connect to the backup list unless something changed in recent AnyConnect or the ASA codes. In the scenarios I mention, I guess Cisco assumes since you hit a gateway, you're fine regardless of whether it fails or not. I know because I had this issue a while back with our load balancing gateways. One gateway was in a hung state where it was still reachable but would never complete new tunnels. Load balancing kept sending new users to the 'bad' gateway, start connecting, error out, never connect. User tries again to the load balancer, error out. Rinse and repeat. Meanwhile the 'good' gateway was available, was listed individually in the backup list but anyconnect never attempted a connection since the 'bad' gateway was reachable.
I hope this helps. I submitted an enhancement request to Cisco regarding this behavior which asked for anyconnect to try every server in the backup list if a tunnel is not established for any reason. I don't know if that went anywhere though.

Paragraphs to Selectable List Script (optimized)

As this script may be of interest to some, I'm posting this version.
This appears to be a troublefree script for converting paragraphs of text to a selectable list while:
1) Getting rid of leading AND trailing white space
2) Preserving punctuation
3) It eliminates a problem where getting rid of trailing white space did not work if there was no leading white space to begin with
4) It is based on submissions by Yvan Koenig and Hiroto with modifications by osimp
It does NOT eliminate blank paragraphs
set myT to "PARAGRAPH 1, and ?!% for punctuation
PARAGRAPH 2
PARAGRAPH 3"
(*Add leading and trailing white space to each paragraph if
it doesn't show up in this post*)
set L to every paragraph of myT
repeat with i from 1 to (count L)
set para to item i of L
repeat while (para starts with space) or (para starts with tab)
set para to (rest of every character of para) as text
end repeat
--IMPORTANT: 1) THE TRY/END TRY BLOCK IS NECESSARY IN THE EVENT OF A BLANK LINE *if* 2) THE 'REPEAT WHILE LAST CHARACTER OF PARA IS " "' BLOCK (below) IS USED (to delete trailing white space). ALSO: positioning of the "end repeats" is crucial; if incorrect, the trailing white space block won't work if no paragraph has leading white space (etc.)! The arrangement shown here appears to be correct.
try
repeat while last character of para is " "
set para to characters 1 thru {(count characters of para) - (1)} of para as text
end repeat
end try
set item i of L to para
end repeat
set _ to choose from list L --with empty selection allowed
if _ is false then error number -128
set mySelection to _ as string
return mySelection
2.7G5 AND OTHERS Mac OS X (10.4.5)

It does NOT eliminate blank paragraphs
set item i of L to para
It does NOT eliminate blank paragraphs, because you maintaining the structure of L.
If you want to get rid of blank line, you need to reconstruct L by changing the script a bit:
set myT to " PARAGRAPH 1, and ?!% for punctuation
PARAGRAPH 2
PARAGRAPH 3 "
(*Add leading and trailing white space to each paragraph if
it doesn't show up in this post*)
set L to {}
repeat with para in every paragraph of myT
repeat while (para starts with space) or (para starts with tab)
set para to (rest of every character of para) as text
end repeat
--IMPORTANT: 1) THE TRY/END TRY BLOCK IS NECESSARY IN THE EVENT OF A BLANK LINE *if* 2) THE 'REPEAT WHILE LAST CHARACTER OF PARA IS " "' BLOCK (below) IS USED (to delete trailing white space). ALSO: positioning of the "end repeats" is crucial; if incorrect, the trailing white space block won't work if no paragraph has leading white space (etc.)! The arrangement shown here appears to be correct.
try
repeat while last character of para is " "
set para to characters 1 thru {(count characters of para) - (1)} of para as text
end repeat
end try
if para as string is not "" then copy para to end of L
end repeat
set _ to choose from list L --with empty selection allowed
if _ is false then error number -128
set mySelection to _ as string
return mySelection

Sub Select list within the Select List!!

Hi All,
I want one solution, i want to have a sub select list within the select list, i mean i want to have a dropdown shown when we point a cursor on any of the Value of
the select list. Sub select list for that value of the select list.
Hope you all got it,Please Reply me if anybody has the solution, I am using APEX version 3.0.1.00.07
Thanks

Hm,
Service Unavailable
The proxy is currently unable to handle the request due to a (possibly) temporary error. Extended error information is:
* Failed to forward the request to the web server at apps.oraclecorp.com:80. This may be due to a firewall configuration error or a DNS failure.
If this situation persists, please contact your security gateway administrator.
Denes Kubicek
http://deneskubicek.blogspot.com/
http://www.opal-consulting.de/training
http://apex.oracle.com/pls/otn/f?p=31517:1
------------------------------------------------------------------------------

Condition that checks the value of an Item derived from a select list

I want to conditionally display and hide items in a region based on a select list item.
Some items will display when the select list is at the default (%null%) and others will be displayed when the select list user selects from the select list.
The display is then updated when the "SAVE" button is pressed and the page processed.
How do I test the select list item to be null. The condition looks like this;
Type: PL/SQL Expression
:P1_SELECT is null
I also tried, :P1_SELECT is not null and :P1_SELECT = '%nul%'.
The latter changed the condition to :P1_SELECT = ''
How can I test the valu in P1_SELECT?
tia,
Sam
Message was edited by:
After a long day I saw that I did not write the condition correctly. Mea culpa.
slavanaway

I had the problem wrong.
The issue was a second field that could have a Y or N or null. When I checked it in PL/SQL expression as
:P_YN != 'Y' and :P_SELECT is null
assuming the null condition would resolve as != 'Y' I had to do an explicit check as
(:P_YN != 'Y' or :P_YN is null) and :P_SELECT is null
That fixed it.... I like null and I hate null
Thanks for the reply

Set Default Value of Multi-select list item

I have a multi-select list item I want to default the value of to '%' (which is really '%null%') and have it selected. I tried setting default value of item, but it doesn't take '%null%'. I also tried a computation with a static of
:P507_ITEM := '%null%'; How do you get the default value set and selected?

Hi
Shijesh is right, you need to change your null return value and use that return value as your default. Try and use something of the same datatype as your real return values if you plan to use '%' to display all as it will make your queries simpler. eg.
Company A returns 1
Company B return 2
% returns 0
Then your query would be...
SELECT ...
FROM ...
WHERE company_id = DECODE(:P_COMPANY,1,1,2,2,0,company_id)
Hope this makes sense.
Cheers
Ben

Display all records from 4 select list

Hi,
trying to associate 4 select list where i could display all records from a list linked to an other list.
1./ Created an item for each select list
P1_employee_name
P1_departments
P1_employee_type
P1_locations
2./Set both null and default values to '-1' for each item
3./Associated these items to source columns in the Region:
where employee_name=:P1_employee_name
or :P1_employee_name ='-1'
and departments=:P1_departments
or :P1_departments ='-1'
and ......
When running the report, couldn't display all records from a given list associated to an other list.
e.g: Display all emp and type of emp for sales dept in Paris.
Thks for your help

I believe the issue is that you need to group your predicates such as:
where (employee_name=:P1_employee_name
or :P1_employee_name ='-1')
and
(departments=:P1_departments
or :P1_departments ='-1')
Also, if you are not already using the "select list with submit" type items, these work great for this case as the page will be submitted when the user changes the value of employeenam and the report will then reflect this change.

Select List problem

I have 3 select lists: the first two are with submit and the last one is just select list. Each list depends on the previous one.
I have set null and default values for each list. The problem occurs when I first start the application, but after selecting an option in the first list all is fine and when I reset the fields everything works as it should.
So the problem only occurs when the application is first launched....
This is the error message:
Error: ORA-01858: a non-numeric character was found where a numeric was expected performing List of Values query: "SELECT TESTTIME d, TESTTIME r FROM TESTSETUP WHERE TESTDATE = :P3_TESTDATE and TERM = :P3_TERM ".
How can this be corrected?
Any help would be greatly appreciated.
Thank - Greg

I have set null and default values for each list
These values are not available in committed session state for the subsequent select lists to use.
Solution: Create a OnLoad Before Header computation (conditional upon the value of the select list being null) to set it to whatever null/default value you want. This will "initialize" the value so that your dependent select lists can work properly.

Report -- filter with selection list -- show all values after select page

Hello!
I have the following problem:
- I have a report
- this report can be filtered with a selection-list
- the selection list is based on dynamic LOV and has a null-value
- I added the code of the report the following, to filter the report after choosing a value of the selection list:
... and (instr(type, decode(:P8_FILTER_type, '%null%',type,:P8_FILTER_type)) > 0)
This works very well.
But my problem is: When the user logs out and the next time, he logs in, the selection list shows " --- show all values --- " (my null-display-value) and the report is empty "no values found".
---> I want to show the first time, the page is selected ALL the values of the report. (this is now only possile if I press the button which belongs to the selection list)
I hope, somebody understands my problem.
Thank you so much,
LISA

Hello Lisa,
The first time it's probably NULL.
So what you can do in your where: (instr(type, decode(NVL(:P8_FILTER_type,'%null%'), '%null%',type,:P8_FILTER_type)) > 0)
Off topic: I also wonder if that where clause can't be simpler? Do you rely need the instr?
Regards,
Dimitri
http://dgielis.blogspot.com/
http://www.apex-evangelists.com/
http://www.apexblogs.info/

Display and return value in select list.

hi,
i want to display the value in select list coming from this quary .
select student_id from class_record where class_id =:p1_class_id and SECTION =:p1_section
minus
select student_id from STUDENT_TYPE_DETAILS where class_id =:p1_class_id and SECTION =:p1_section;
but i want f_name and last name with student_id .f_name and l_name store in table s_per_det.student is also in that table.
how can i define display value and return value in this quary using 3rd table s_per_det.
How can i do this.
Thanks
manoj

Ooh, MINUS.... Can you not use a NOT EXISTS in this case, could have a big effect on the execution plan?
Something like this perhaps?
SELECT f_name||' '||l_name,
       stundent_id
FROM class_record a,
     s_per_det b
WHERE a.student_id = b.student_id
AND   a.class_id   = :P1_CLASS_ID
AND   a.section    = :P1_SECTION
AND   NOT EXISTS(SELECT 'X'
                 FROM student_type_details c
                 WHERE a.student_id = c.student_id
                 AND   c.class_id = :P1_CLASS_ID
                 AND   c.section = :P1_SECTION)Cheers
Ben
http://www.munkyben.wordpress.com
Don't forget to mark replies helpful or correct ;)

Select list enable / disable in tabular form

Hi,
I have created report on (ACT_COA_SEGMENT_MAS) table and this is master table , and created link on this report, when i click on report link, control moves to tabular form that is based on detail table (ACT_SEGMENT_VALUES_MAS)
In master table there is column,
SEGMENT_ID number primary key;
QUALIFIER varchar2(1);
If in master table qualifier column value is 'N' then
then in detail table (ACT_SEGMENT_VALUES_MAS) column account type cannot be null and column should enable.
If in master table QUALIFIER column value other than 'N' then Account column in detail table should disable . and value should not be enterable.
and ACCOUNT_TYPE column in deatil table is a select list.
How i can do this?
Thanks & Regards
Vedant
Edited by: Vedant on Jan 10, 2013 10:14 PM

Vedant wrote:
If in master table qualifier column value is 'N' then
then in detail table (ACT_SEGMENT_VALUES_MAS) column account type cannot be null and column should enable.
If in master table QUALIFIER column value other than 'N' then Account column in detail table should disable . and value should not be enterable.
and ACCOUNT_TYPE column in deatil table is a select list.
How i can do this?One way - sadly a bit of work - would be to use APEX_APPLICATION_ITEM to generated the detail items as a manual tablular form where you can control the disabled property when generating the tabular form fields using CASE statements, writing manual PL/SQL processes and the built-in APEX_ITEM collection to manually perform insert/update/delete operations on submit. Check the documentation for the full syntax of using APEX_ITEM functions to generate HTML items.
An example from the Oracle docs looks like
SELECT
empno,
APEX_ITEM.HIDDEN(1,empno)||
APEX_ITEM.TEXT(2,ename) ename,
APEX_ITEM.TEXT(3,job) job,
mgr,
APEX_ITEM.DATE_POPUP(4,rownum,hiredate,'dd-mon-yyyy') hiredate,
APEX_ITEM.TEXT(5,sal) sal,
APEX_ITEM.TEXT(6,comm) comm,
deptno
FROM emp
ORDER BY 1where the disabled property could be specified in the unlisted fifth argument to APEX_ITEM.TEXT. The first item to the APEX_ITEM calls is a number defining the G_FXX global variables so that 1 identifies the item later as apex_application.g_f01(9) - 9 being symbolic for a collection identifier -, ename as apex_application.g_f02(i),m and so on. The G_F99 items can be reference on submission in Pl/SQL processes through looping, something like (this example assumes all array items are populated - under some circumstances they may not be)
for i in 1..apex_application.g_f01.count loop
update my_table set sal = apex_application.g_f05(i) where empno = apex_application.g_f01(i);
end loop;Edited by: riedelme on Jan 11, 2013 7:12 AM

Select list works for some users not for others

Apex 3.2, Oracle 10g
I have a page with a select list. (other select lists work fine) This view is a based on a view over a dblink with the chain being (public synonym -> dblink view -> dblink real view )
One user logs into the Apex app and the select list populates.
I log in to the app, either through the developer login or the app login, navigate to the same page and the select list does not populate.
What can cause this in Apex or is it a database issue.
Someone said it may be a rights issue, but I thought all Apex users appeared as the same 'user' to the database.
Miscellaneous points: The app authentication is via LDAP/OID and I can get the select list code work in SQL Developer.
Thanks,
Sam

not sure what you are asking
It is a "Select List"
The sql is
select x d, x r
from view
wher x is not null
order by 1
The view is a synonym in the application schema, points to a view on the same database instance (different user) which points to the real view via dblink to a different database instance.

How to get the value from select list to text box

Hi,
I have a select list i want to retrieve the value from select list to text box.
How can i do that???
Regards,
Sakthi.

Hi Sakthi,
Yo can use the Java script for that..
Dynamically the value will come into text box.
Use the below script.
<script type="text/javascript">
function disFormItems()
var lReturn = $v(here your select list name)
alert(lReturn);
document.getElementById(here your text box name).value =lReturn; }
</script>Cheers,
Shan

How to get a parameter from a HTML select list in a servlet

Hi!
I have the following problem :
In a HTML form I have the following select list:
<select name="tickets">
                                        <option value="1">1</option>
                                        <option value="2">2</option>
                                        <option value="3">3</option>
                                        <option value="4">4</option>
                                        <option value="5">5</option>
                                        <option value="6">6</option>
</select>And in the servlet I try to read the value I have selected doing : String tickB = (String) request.getParameter("tickets");But for my amazement tickB always has the value 1, althought I have selected in the list the value 2,3,4,5 or 6
�Where is the error ? �Have I to do with getParamaterValues instead getParameter to obtain the correct value?
Bye
Edited by: bladu on Jun 4, 2008 1:25 AM

Where is the error ? No error in portion of code you have shown.
But for my amazement tickB always has the value 1, althought I have selected in the list the value 2,3,4,5 or 6Are you sure there are no other form element(hidden field, text field) with same name tickets ? If you are using GET method, you may check the url to see if there are more than one parameters named tickets set in it
Have I to do with getParamaterValues instead getParameter to obtain the correct value? Not required.

How to display a value from Select List by default

I have a Select List on a form and I need to on page load show an entry from the SL depending on the user Id of the user logged on. For example, if the SL had 3 entries: 'Div1', 'Div2', and 'Div3', depending on the division the user belongs to (I can determine that from his user Id using a SQL), say, I need to display 'Div2' to the user in the SL instead of the usual NULL or '---- Select Div ----'. 'Div1' and 'Div 3' entries will still be part of the SL, but for user's convenience I need to display their division.
Any ideas?
Thanks,

Hi Ajay,
you need to specify your apex version, database version and so on to make our help specific.
Anyhow you can create a page process- for example one at On Load before header.
For example;
[code]
declare
v_division varchar2(32);
begin
--select default division
select my_division
into v_division
from my_division
where my_division=:APP_USER;
:P_DIVISION:=v_division;
end;
[/code]
Then in the default of your select list, specify P_DIVISION as the default. Using one of several methods
Understanding Page-Level Items
Kofi

Optimal gateway selection list

Similar Messages

Maybe you are looking for