OSB with HP StorageWorks SDLT 320

Hi;
I'm trying to do a tape backup using OSB to HP storageworks SDLT 320 tape Drive.
I can configure the tape, and OSB can ping it successfully.
But, when i start the backup, OSB indicates that it is waiting for the tape (Pendding hardware ...).
I think that i must mount the tape before doing backup.
If it's the case, i need a script/tool to autoload the tape drive.
Any idea?
Thnx

Hi folks;
I've resolved the problem.
I must disable the tape drive currently used by HP storageworks and let OSB install its own drive.

Similar Messages

Problem with a Toshiba PX1267E 320 external drive

Hello all
I have a problem with a Toshiba px1267e 320 external drive, when all was ok with it I would switch on and the blue led would come on and change blue /violet as it was found on my laptop, a small vibration could be felt if I handled the case indicating that the d/d motor was on.
On that fateful morning I switched on did an explore in my computer and found no ext drive, checked the drive blue led on touched the case could detect no vibration, unclipped the drive from the case put my ear to it heard faint clicking.
I removed device and connected to caddie, this time I could feel the motor going, connected to laptop, new hardware found did my computer explore and found no drive, checked device manager and found it so I uninstalled and reconnected usb with same result.
I am not sure what do next.
I had a word with computer shop if they could recover a while I wait they said at least a 6 hour job if possible (dont want to leave at shop)
Bought me another western digital same model no and also new power supply to try swapping the electronics board just in case therein lies the fault /or possible us power/s but I am clutching at straws here.
Any of you guys here got anything like this happen ? any suggestions?
I am curious to know what they would try in the shop to recover although he said he couldn't guarantee results.
I would welcome any helpful suggestions (not throw it in the bin)

>I removed device and connected to caddie, this time I could feel the motor going, connected to laptop, new
> hardware found did my computer explore and found no drive, checked device manager and found it so I
>uninstalled and reconnected usb with same result.
>I am not sure what do next.
I think the external HDD is dead
Maybe its a head crash this would explain the faint clicking and other noises
Unfortunately, I such case you can do nothing

Solaris Can't detect Quantum SDLT 320 Tape Drive

Hi All,
I have a Quantum SDLT 320 connected to Sun Fire v490 which can't be detected in solaris but can be detected in OBP .
Can someone help about this issue.
Your prompt response will be very appreciated.

Hi All,
Thanks for your help.
The problem is now solved when i proceeded as followed:
1. When i executed the command cfgadm -al
the output showed the below information about the tape drive controller:
c3 Connected unconfigured OK
I disconnected the controller and then run the devfsadm -c tapes which took about 1 hour to complete and then, now the system can detect and tape and the first backup run
successfully.

OSB with AIA

We are trying to use OSB with AIA EBS.
Use case is :
OSB Proxy service will receive the inbound payload, transform into AIA EBO and a Business service will invoke AIA EBS.
Challenge is OSB can't access the AIA EBO schema (EOL) from MDS. Can OSB directly access AIA schema? or we have to import the whole AIA schema library(EOL) to OSB?
Of course we don’t like to maintain two copies of AIA library.
Seeking your expertize in this area.

In my project, the curstomer decided to build EBS layer with OSB, so we have to keep the canonical components into OSB layer. Obviously we have to keep 2 copies of AIA Components as OSB will not recognise MDS paths. So i kept a copy of the entire AIAComponents into a OSB and modified the business services by adding the port information to the EBS services, then only you will be able to see the operations to create a proxy service or business service.
Then you can create proxy service out of the EBS service and then call the provider ABCS component as business service. This is the way i did and did a presentation to customer.
I had provided them the issues as well and decided to go with mediator and MDS.
I think in SOA 12 g, the OSB engine will be part of the SOA then we can use it.
Thanks,
Vijay

Mac mini with HD300 or nVidia 320?

Hi,
I'm picking up a Mac Mini for my son for general use and a little light gaming.
Looking on ebay i can get the current 2.3ghz i5 with the intel HD300 graphics or the previous model with the nVidia 320 for around the same price, (£400)
My question is which is the better graphics performer?
The intel has 512mb and the nVidia 256mb?
Many thanks.

Stay away from the HD3000 if you plan on using Adobe apps or gaming.

[OSB1031] how to call a RESTful service from OSB with authentication

Hi all,
I called successfully a RESTful service from OSB.
We have a business service, named OrderTracer, that wraps the call to the RESTful service.
The RESTful service requires an authentication so we are trying to find out how the OSB business service should authenticate itself against the RESTful service.
In addition the RESTful service accepts username/password coded as base64.
So we defined a Service Account with static resource type and we added the reference to this service account in the business service.
But when the OSB business service calls the RESTful service, we got an error:
<fault>
<con:fault xmlns:con="http://www.bea.com/wli/sb/context">
<con:errorCode>BEA-380000</con:errorCode>
<con:reason>Unauthorized</con:reason>
<con:location>
<con:node>RouteNode</con:node>
<con:path>response-pipeline</con:path>
</con:location>
</con:fault>
</fault>
Does anyone have any hint ?
Any clue would be of great help.
Thanks in advance
ferp

Hi,
There's a sample on JSON REST here...
http://java.net/projects/oraclesoasuite11g/downloads/download/OSB/osb-206-JSONREST.zip
For other samples, see this...
http://java.net/projects/oraclesoasuite11g/pages/OSB
Cheers,
Vlad

OSB with database adapter using stored procedure

Hi All,
We have a following requirement, in OSB while using the DB adapter with stored procedure.
1) the store procedure has custome datatype as inout parameter
2) send reference cursor as input to stored procedure
Can you please let me know how to do this.
Thanks,
Vinoth

Please go through below links -
Section "9.7 Stored Procedure and Function Support" of Tech Adapter user guide - http://download.oracle.com/docs/cd/E17904_01/integration.1111/e10231/adptr_db.htm#CHDFBBCD
http://blogs.oracle.com/middleware/2010/05/using_jca_adapter_with_osb_11113.html
Regards,
Anuj

Caching in OSB with Business Service

Hi All,
I am done with business service development, but I need to configure caching to fetch the data from cache if TTL (Time to Live) <24 if is more then my request to interact with the database can please help how I can I do it, as I am new to caching concept.
Thank You,
Vinay Kumar

Hi Vinay, Select the Business Service - Message Handling Configuration - in Advanced Settings section, you can configure caching for the business service; select Result caching as Supported, and specify cache token (unique key) and expiration time (TTL). Note- once the TTL exceeds for a particular data, the business service will fetch the result from the target system/database and cache it, and the cycle repeats (no specific configuration to be done for this). Also, before configuring the above, first enable the caching globally in OSB; go to Operations - Global settings - select Enable Result caching, and activate the changes.

OSB with request response MQ business service

Hi,
We have OSB webservice whice interacts with MQ via business service. We need to send the request to MQ request queue and get the response from the response queue.
For this, we have configured a business with MQ transport, request-response is enabled, message id is set for the correlation, auto generate correlation value is chosen.
The business service sends the message but unable receive the response from the response queue. Failing with the error message like
The invocation resulted in an error: [WliSbTransports:381918]Failed to receive response, within the configured timeout, for request message with id 42454BD3E5F7647914544E793F9F0000013EC9DF03918057 and correlation id 42454BD3E5F7647914544E793F9F0000013EC9DF03918057.
But we checked with the end system, the response is sent tot he response queue in no time. We also increased the time out but still same issue.
We noticed that if we dont send the message id, we are getting the response but not response of the request sent but some other response.
Please suggest what needs to be done to fix the issue.

Open your business service and navigate to HTTP Transport configuration page and check what is the http type is enabled.
Look to me its with GET method, change it to POST and re-try.
If the above solution is not helping, try to check the Follow HTTP redirects check box below the Advanced Setting in same page.
Thanks,
Vijay

How to configure a Proxy in OSB with Digest Authentication?

Hello, Guys.
I need a help with this subject.
I have a demand to configure a Proxy in OSB 11.1.1.6 with Digest Authentication. I'm using a Embedded Ldap with Identity Asserter.
I'have configured a DefaultAuthenticator and the DefaultIdentityAsserter to support Digest Password and create a new LdapIdentityAsserter pointing to my embedded Ldap.
When I'll create a new Proxy, in the security options, i can see the digest options to authenticate my username and password. I selected the one of all the options, but in the time of the Proxy test the authentication didn't work.
Could anyone help me?
Thanks you.

Unfortunately, a reference trigger can't be used for continuous acquisition after the trigger. The maximum post-trigger count is either 2^24 or 2^32 depending on your hardware. Depending on your sampling rate and how many samples you expect to acquire before issuing a software stop, using the max post-trigger count may be sufficient for you. There are a couple of other options I can think of that you might want to try:
1.) If possible, play with the trigger condition such that it occurs at the start of your pre-trigger data and use it as a start trigger instead. I suspect this may not be possible.
2.) Set up a continuous acquisition and implement detection of the trigger condition through software. This is more software work and is more CPU intensive than the hardware solution, but it can definitely be made to work.
3.) With some creative use of the counters, you may be able to latch the sample clock number that trigger occurred on. This would allow you to setup a continuous acquisition and use the hardware to tell you where the trigger occurred instead of figuring it out in software. What I'm thinking is you would set up a buffered event counting task with the ai/SampleClock as the timebase source of the counter and the trigger signal as the sample clock of the counter. By reading the first count value, you should know which AI sample the trigger occurred. From there, you can seek to the right position in the buffer and begin reading data indefinitely.
Good luck!

Problem connecting weblogic OSB with IBM websphere via foreign JMS

Hi All,
I am trying to setup Foreign JMS. My configuration doesn’t work.
Could you please let me know if I am missing anything .
All my configuration details are done as specified in this link http://www.oracle.com/technology/products/integration/service-bus/docs/osb-websphere-whitepaper.pdf
Here is what I did.
In OSB sbconsole
OSB business Service ENDPoint URL jms://webspherehost:9082/sampleQueuemanager/sampleQueue
In websphere
Created a queue connection factory and a queue from the webspehere administrator console.
Modified JSMAdmin.config to enable the following…/Java/bin/JMSAdmin.config.
INITIAL_CONTEXT_FACTORY=com.sun.jndi.fscontext.RefFSContextFactory
PROVIDER_URL=file:/C:/JNDI-Directory
Ran JSMAdmin.bat to bind the JNDI
def qcf(sampleQueuemanager) qmanager(QMGR) HOSTNAME(webspherehost) PORT(1327) TRANSPORT(CLIENT)
def Q(sampleQueue) queue(sampleQueue) qmanager(QMGR) PERSISTENCE(PERS)
InitCtx> dis ctx
JMSADM4089 InitCtx
.bindings java.io.File
bck_.bindings java.io.File
a sampleQueuemanager com.ibm.mq.jms.MQQueueConnectionFactory
a sampleQueue com.ibm.mq.jms.MQQueue
4 Object(s)
0 Context(s)
4 Binding(s), 2 Administered
In weblogic admin console
Created foreign JMS, destination and connection factory as mentioned in the following link.
http://download.oracle.com/docs/cd/E12840_01/wls/docs103/ConsoleHelp/taskhelp/jms_modules/foreign_servers/CreateForeignConnectionFactories.html
When I execute business service from OSB sbconsole, this is what I get.
+The invocation resulted in an error: [JMSPool:169803]JNDI lookup of the JMS connection factory sampleQueuemanager failed: javax.naming.CommunicationException [Root exception is weblogic.socket.UnrecoverableConnectException: [Login failed for an unknown reason: HTTP/1.1 400 Bad Request]].+
Thanks
siva

Little confusing. Are we not supposed to use osb host name and port along with foreign connection factory created in weblogic for OSB BS?.
You said: jms://webspherehost:9082/sampleQueuemanager/sampleQueue
We have to jms://osbhost:port/ForeignQueueManagerInWeblogic/ForeignQueueInWeblogic
Manoj

OSB With ws-addressing

Hi All,
Does OSB's business service supports dynamic JCA connection JNDI using ws-addressing. I mean, dynamically i am going to get JNDI value, which i need to pass it using ws-addressing in connecting to back-end. Something like dynamic partner link in BPEL.
Any help on this really appreciated
Regards & Regards
Venkata Madhu

Hi Venkata,
I think it is not possible with OSB currently but if I am not wrong then a similar request was raised with product development some time back. You may raise a SR with support and ask for an enhancement anytime. If product development considers your request then this feature might get added in upcoming release or you may get an exclusive patch.
As a workaround, you may create desired number of business services in OSB and use dynamic routing to call them from message flow.
Regards,
Anuj

OSB with Rest JSON webservice

Hi, I am new to OSB and working on making OSB as a pass thru for RestFul JSON webservices. I am able to get JSON response back in case of GET request however for POST request I am getting this error:
<con:fault
xmlns:con="http://www.bea.com/wli/sb/context">
<con:errorCode>BEA-380000</con:errorCode>
<con:reason>Unsupported Media Type</con:reason>
<con:location>
<con:node>AegisRouteNode</con:node>
<con:path>response-pipeline</con:path>
</con:location>
</con:fault>
I have used transport header in response action to convert content type to application/json. I am not sure why it works perfectly for GET request but fails for POST.
I appreciate any help that can be provided. Thanks.

> I have used transport header in response action to convert content type to application/json
Why in response? o_O
My understanding of what is happening is that the remote server rejects your POST with HTTP 415. I.e. you need to set the Content-Type transport header in request pipeline.
For GET though the server may just ignore the Content-Type header or lack thereof, and that's why it may work.
Try to point your call via Fiddler to see the actual HTTP request and response, it should give you the idea what's going on.
Vlad
http://vladimirdyuzhev.com

OSB with Dell PowerVault 100T DAT7 2

Will Secure Backup work with the Dell 100T DAT72 tape drive?

This is an area that I have very little experience. I'm not sure what a library is to be honest. Is this something that installs with the drive, or is it a piece that needs to be purchased or obtained separately? All I can tell you is that I followed the OSB instructions exactly:
10gR2 10.2.0.2.0 Windows 2k3 R2 on Dell PowerEdge rack
Created Library with attachment raw device //./obl0
But the show properties revealed the message "no hardware info is available for library tc-lib - The system cannot find the file specified"

OSB with HP MSL2024

Hi
I have a HP MSL2024 library with two tape drives. When I submit two jobs in the OSB home page I see that backups run concurrently:
library MSL2024 in use by obrobotd on rubxyz, process 21569
drive (1) dte1 in use by obrobotd on rubxyz, process 21569
drive (2) dte2 in use by obrobotd on rubxyz, process 21569
but when I login to HP storage msl2024 tape library webpages I see on the system status that always one of the drives is writing. Never both. For example. For a few seconds drive 1 has status writing, the second drive status is idle, for the next few seconds both drives are idle and for the next few seconds first drive is idle and the second is writing. So backups don't run concurrently but in turn and very slow.
What could be the reason of such behavior?? Is a problem with configuration of the OSB or the HP tape library or somthing else??
thanks for help
Jan

Still the same problem
MSL2024:
Device type: library
Model: [none]
Serial number: [none]
In service: yes
Debug mode: no
Barcode reader: yes
Barcodes required: no
Auto clean: no
Clean interval: (not set)
Clean using emptiest: yes
Unload required: yes
Ejection type: auto
Min writable volumes: 0
UUID: b1cad8e6-af07-102b-b80f-001438b8cffc
Attachment 1:
Host: rubryk-pl
Raw device: /dev/sg1
Connection type: [unknown]
Reservation 1:
Component: obrobotd
Host: rubryk-pl
Process: 25450
Inquiry data:
Vendor: HP
Product: MSL G3 Series
Firmware: 4.20
Serial number: DEC06220KE
Element counts / addresses:
1 mte: 0
23 se : 1001 - 1023
1 iee: 101
2 dte: 1 - 2
Moves:
From mte, to: mte 0 se 1 iee 1 dte 1
From se, to: mte 0 se 1 iee 1 dte 1
From iee, to: mte 0 se 1 iee 0 dte 1
From dte, to: mte 0 se 1 iee 1 dte 1
Ok_ops: move=1, reserve=1 sense_dev=1, sense_ele=1, unload_any=1, sense_dev_range=1
Device characteristics: two_d=0, is_120=0, fake_mte=0, fake_iee=0, one_target=0
State of barcode reader: present
Display: none
Dte 1: target 4 lun * name dte1 (raw device name /dev/sg0)
warning: dte 1 may be misconfigured; (on bus 0) is at target 0, lun 5,
which doesn't match the information provided by the library.
Dte 2: target 5 lun * name dte2 (raw device name /dev/sg2)
warning: dte 2 may be misconfigured; (on bus 0) is at target 0, lun 5,
which doesn't match the information provided by the library.
Warning: bus info unknown or drive not installed
dte1:
Device type: tape
Model: [none]
Serial number: [none]
In service: yes
Library: MSL2024
DTE: 1
Automount: yes
Error rate: 8
Query frequency: [undetermined]
Debug mode: no
Blocking factor: (default)
Max blocking factor: (default)
Current tape: 2
Use list: all
Drive usage: 4 hours, 41 minutes
Cleaning required: no
UUID: aa02df66-af0f-102b-b80f-001438b8cffc
Attachment 1:
Host: rubryk-pl
Raw device: /dev/sg0
Connection type: [unknown]
Reservation 1:
Component: obrobotd
Host: rubryk-pl
Process: 25450
Reservation 2:
Component: obtar
Host: rubryk-pl
Process: 25560
Reservation 3:
Component: observiced
Host: rubryk-pl
Process: 6374
Inquiry data:
Vendor: HP
Product: Ultrium 3-SCSI
Firmware: D22W
Serial number: HU10823PAR
Hardware compression: not available
dte2:
Device type: tape
Model: [none]
Serial number: [none]
In service: yes
Library: MSL2024
DTE: 2
Automount: yes
Error rate: 8
Query frequency: [undetermined]
Debug mode: no
Blocking factor: (default)
Max blocking factor: (default)
Current tape: 4
Use list: all
Drive usage: 4 hours, 38 minutes
Cleaning required: no
UUID: e7e9ec0c-af0f-102b-b80f-001438b8cffc
Attachment 1:
Host: rubryk-pl
Raw device: /dev/sg2
Connection type: [unknown]
Reservation 1:
Component: obrobotd
Host: rubryk-pl
Process: 25450
Reservation 2:
Component: obtar
Host: rubryk-pl
Process: 25636
Reservation 3:
Component: observiced
Host: rubryk-pl
Process: 6374
Inquiry data:
Vendor: HP
Product: Ultrium 3-SCSI
Firmware: D22W
Serial number: HU10823P9R
Hardware compression: not available
sg_map -x -i
/dev/sg0 0 0 4 0 1 /dev/nst0 HP Ultrium 3-SCSI D22W
/dev/sg1 0 0 4 1 8 HP MSL G3 Series 4.20
/dev/sg2 0 0 5 0 1 /dev/nst1 HP Ultrium 3-SCSI D22W

OSB with HP StorageWorks SDLT 320

Similar Messages

Maybe you are looking for