Overlay inspection info in VBAI running in Labview

Hi,
I'm running an inspection using the NI Vision Builder AI palette in Labview.
I show images in Labview using "VBAI Interface - Get inspection Image.vi" but the images appears without info (Overlay objects like ROIs, edges,...)
Is there anyway to overlay some inspection info???
Thanks so much for helping me :-)

Does the image have overlay information when you run the inspection in Vision Builder AI? If so, are you reducing the image size with the Get Image function? Reducing the image size, removes any overlays, although this is fixed in the 2013 version that will release soon.
If you aren't reducing the image size using the Get Image VI, you can add overlay information in Vision Builder using the Overlay step, or you could get the results in LV using the Get Measurements VI and overlay the info there. I would recommend using the Overlay step in VBAI since it makes it easier to align all your results and easily get them from a simple UI.
Hope this helps,
Brad

Similar Messages

Execute a VBAI code with Labview

Hello
I work with a CVS, and for that I create a VBAI code that I need to use with Labview, I already use the tool "migrate inspection to labview" and tryed this VI. I added the "inspect main" VI on my cvs target, but I did'nt do what I put on the VBAI code.
How can I do to execute exactly the VBAI steps in Labview.
Thank you for your help
Attachments:
Inspect Main.vi ‏103 KB

Here's a sample LV 2013 project with a CVS target and the build specs to get a startup app.
1. Right clikc on the CVS and select Properties. Change the IP Address to match your target's.
2. Right click on the "My Real-Time Application" under Build Specification for your target and select Build
3. Once the Build is done, right click again and select Deploy. This should automatically create a Configuration Files folder on the target with the correct files.
4. Right click again and select "Run as Startup" and this will ask you to reboot. Now the VI will start running when the target reboots.
If you need to debug, you can stop the startup app on the CVS by right clicking on the target and connecting. Then just open the Inspect Main.vi from the project when it's under your CVS target) and run it. The Configuration Files should already be downloaded to the target after following the above steps.
Hope this helps,
Brad
Attachments:
Sample Project.lvproj ‏36 KB

How do i run a Labview file through a windows phone?

Hello there
How do i run a Labview file through a windows phone or a tablet? is it possible
is there any phone specifications required? or steps?
Thanks alot

Blokk wrote:
na1992 wrote:
hahaha my baad
i mean if i have done my labview file on laptop and i want it to connect my file to a microcontroler using usb or any serial connection, i want a way that my labview file will run if i store it on a phone.
i searhced about exe format but i didnt find enough info
Sorry, but you should define more precisely what is your goal:
" i searhced about exe format but i didnt find enough info"
If you build an exe using Labview, that exe will not run on iOS, or Android, if this is what you ask...
Nor Windows Phone or Windows RT. A LabVIEW exe is compiled and linked for x86 or AMD64 architecture with Win32 API architecture and will only run on Windows for x86 or x64 systems.
Windows Phone and Windows RT are despite the similarity in the name technically completely different platforms to the normal Desktop Windows system, just as different as MacOS X or iOS.
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

Running A LabVIEW executable in Windows 7

Can I run a Labview executable created with Labview 8.6(32-bit) in windows 7 or Vista. If this can be done then how to do it? I've tried copy the lvrt.dll(run-time engine) into the system 32 folder, but it doesn't solved my problem. For info, My Labview exe file also consist the fuzzy logic toolkit.
Hope someone will help me. Thanks.
Lojius.
Solved!
Go to Solution.

hi lojius,
For that you need to install labview 8.6 run time engine which is freely downloadable....Please find it at the link
http://joule.ni.com/nidu/cds/view/p/id/1101/lang/en
thanks and regards,
srikrishnaNF
Message Edited by srikrishnaNF on 03-23-2010 05:46 AM

How can I run a labview executable file inside a VI

How can i add and run a labview executable file inside the vi and grab the output of the executable file to be used in the vi?
mytestautomation.com
...unleashed the power, explore and share ideas on power supply testing
nissanskyline.org
...your alternative nissan skyline information site

Hi cmdrb,
to run an executable you use SystemExec function.
To get the output of your (LabVIEW-made) executable you need to program some data transfer means: you may use network functions or file functions. In both cases your "LabVIEW executable" needs to provide that options…
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Error when running the LabVIEW program

hello...........
I'm newbie in LabVIEW....I have a problem when i'm running the LabVIEW program...i want to analyse data using the LabVIEW through the real experiment....
My problem is, there is an Error when i try to start the program...This Error forced me to restart the program several times until it can run.......By the way, i'm using Picoscopes 3206 to connect the LabVIEW program in PC with the real experiment.....
Here, I'm attached the picture that I snap when the Error occur....
Attachments:
error.JPG ‏222 KB

You have to try to isolate the problem...
Use 'Diagram disable' or 'Case' structure to run special part of code or try write a specific code to access and manage your equipment.
Several questions could help:
- Are you up to date with your hardware driver?
- Do you call external ressources (ex: dll)? perhaps with instability
- Do you properly close connection with your equipment after using?
- With your offline mode, do you load all the code, including hardware driver or do you use a special method without no loading the specific code?
- When you are able to run after many tries, is the program stable? Can you re-start it without exiting LabVIEW?

)How can we schedule the info package daily run at 6 AM, with out useing in

Hi
   Can any one explain 1) what is information broadcasting &how can we use this.
2)What are the settings we have to do when we use the charts in WAD's
3)How can we schedule the info package daily run at 6 AM, with out useing in process chains
Thanks
Bharath

Hi,
Information broadcaster :
      you can precalculate and distribute(thru mail) the query, workbook and webtemplate through online link or html file to the receipents (users).
have a look at the below link.
     http://help.sap.com/saphelp_nw04/helpdata/en/3a/0e044017355c0ce10000000a1550b0/frameset.htm
Infopackage scheduling:
     you can schedule the infopackage daily at your desired time .In the schedule tab ,select the start later in background and in the scheduling option give the date and time and give the period values as daily.
Regards,
Siva.

How to run the LabVIEW exe as background process?

Dear All,
               I want to run my LabVIEW exe as background process, which wont show as the process in the task bar as shown in the .jpeg file.
                I want to run it as a background services as like runs in the windows processes.
                Please suggest me something.
Thanks,
Nishant

Dear Smercurio,
           Thanks for the good one, but it still requires the windows XP or later OS, when i extract the software, it gives me this error.
           Even Fire Daemon software (same one provided by Alessio in this post) is also running the same, and we even dont have to make it Automatic to start at boot up time, it automatically creates the automatic service which also runs at boot time, so not to worry about anything.
Thanks,
Nishant
Message Edited by Nishant on 12-05-2006 10:12 PM
Message Edited by Nishant on 12-05-2006 10:16 PM
Attachments:
rktools error.jpg ‏12 KB
rktools error.jpg ‏12 KB
rktools error.jpg ‏12 KB

Is it possible to run a LabVIEW LLB from Version 8.6.1 on a Version 8.6 platform?

We need to move a Version 8.6.1 LLB to a Version 8.6 platform. Assuming our 8.6.1 LLB does not use any 8.6.1 specific features, can I convert it to run under LabVIEW 8.6? Thanks!

TCPlomp wrote:
One thing as a tip, don't usean LLB as a way to develop VIs in. Only use them for distributing code. If one of your VIs become broken, your whole LLB will be broken.
Ton
Actually this is not entirely true. The VIs itself are independant entitities in an LLB, so the brokeness of one of the VIs does not automatically have any influence on other VIs inside that LLB.
That said, the VIs do get written to the LLB individually, and although writing changes to an LLB is always done on a shadow copy of the LLB, which only replaces the original LLB AFTER the writing has been finished without any errors, there is of course always a chance that writing of a VI itself goes havoc in some ways. This could in principle destroy the integrity of the LLB data structure, and in such a way make the LLB as whole inaccessible. But because of the shadow copy technique it is a rather seldom event.
Rolf Kalbermatter
Rolf Kalbermatter
CIT Engineering Netherlands
a division of Test & Measurement Solutions

How to save a screenshot while VI is running in LabVIEW 8.5

I am wondering how to save the screenshot of PC while the VI is running in LabVIEW 8.5.1?
Thank you.

I like using the Snipping Tool built into Windows 7 and later.
http://windows.microsoft.com/en-us/windows7/products/features/snipping-tool
A couple things I like,
1. When you make a snip, it automatically puts it in the clipboard so you can quickly paste it into a document
2. If you hit "Cancel" on the current snip process you put it into a kind of "triggered" mode. So, I can put my mouse over a drop down menu or other interactive component in LabVIEW, then press ctrl+PrtScn to call the Snipping Tool to action, and it allows me to snip whatever interactive components were open. For example, here is a snip of a right-click on a control that shows it being highlighted and the right click menu.
Tim A.
National Instruments

How can I run a LabVIEW app as a service in 8.2

I have need to run a LabVIEW created Executable as a Service using LabVIEW 8.2. I have heard 8.2 can host it but I cannot find any docs on this. Any help would be appreciated. SvcAny was not an option that worked.

I would suggest trying to add the exe to the services under Control Panel >> Administrative Tools >> Services. This should cause the exe to launch as a service.
Brian R.
District Sales Manager
Washington DC
National Instruments

Once running the labview program which contain DAQ Assistant ,the message of "ERROR-50405....." appear.

Once running the labview program which contain DAQ Assistant and can be run without any error before, the message box of "ERROR-50405....." appear which capture down in the attachment. We use PCI6221 and LabVIEW 8.0 in Windows XP. I also found that the Device Manager of Window have recognized the PCI6221.
Any help on this situation would be great.
Attachments:
labview error.JPG ‏145 KB

Hi~
This error is due to signal interference between the device and the computer. This could be environmental or due to the PCI Controller. You can on a different computer to see whether this problem persists.

Can multiple executables run on Labview RT?

Can I execute processes on the Labview RT that are non-VI processes? From what I understand, the Labview RT is tightly coupled with the Pharlap RTOS. NI has tools to create an executable to run on Labview RT. Can I run other executables created from other applications? What if I want to run a Labview RT executable and a non-Labview RT executable on the Pharlap RTOS? The PXI-8196 RT controller will have a FAT file system? Can the PXI-8196 RT, with its Labview RT and Pharlap RTOS, initiate multiple executables?
Wayne

Hi Wayne,
Chris' answer was spot-on. To clarify the other points, the RT controller will require the FAT file system (FAT32 in the case of the 8196 RT), and you can only run one executable at a time. From within this executable, you can call DLLs and other VI's, but calling an external executable will not work. If you choose to create a DLL, I recommend using the DLL Checker 7.1.1 utility, which can be found in our KnowledeBase. This will verify that the DLL does not make calls to functions or libraries not supported on the Pharlap OS, since some windows libraries and function calls are not available in RT.
Cheers,
Matt Pollock
National Instruments

How to run a labview program(*.vi) in VB6?

Hi:
I use measurement studio 6 and VB6.I want to run a labview program(*.vi) which is no parameters to input to judge whether spectrum ananlyzer is in ready state.How can I run the program? Can the judgement be implemented through measurement studio 6?
Thanks for your help!

You can do this with VI Server. Here are a few articles and examples that you can look at to get started:
LabVIEW and Visual Basic - Example 3: Sharing Code with Visual Basic
Calling a LabVIEW Executable from Visual Basic
Calling a LabVIEW VI from Visual Basic through ActiveX
Passing Data between LabVIEW and Visual Basic Using the ActiveX Server
Calling LabVIEW as an ActiveX Server from Visual Basic
- Elton

How can I get a Mac to run a LabVIEW VI that was created for Windows? (it calls DLL files)

This is for a spectrometer. A motor controller is connected by serial and a lock-in amplifier is connected through GPIB. I have a Windows version of the VIs I need to get it all running, but I need to get it running on a Mac. The program was written in LabVIEW 6.0.1 and I have both version of 6.1. Is there a type of file that Mac uses that are similar to DLLs? Is this even possible? Any advice is greatly appreciated.

> Thanks for your help. The supplier of the VIs hasn't made a Mac
> version. Is there a way I can find what the information is that is
> being passed? and use a static library to pass the information to the
> Mac? I'm very interested in hearing the 'not necessarily easy' answer
> if you would share it. ([email protected])
>
You can open the VIs on a PC or Mac and double click on the DLL node.
It will show you the parameter info, the function name, path to the DLL,
etc.
If you have the source code to the DLL, then make it on the mac using
the Metrowerks CodeWarrior compiler. If you don't have the source, then
you need to either shift to using diagram nodes exclusively or come up
with some other way of replacing the DLL.
For the details on compiling a DLL, you should look at your manual that
came with CodeWarrior and look at the CIN Manual or search online for
something ...
Greg McKaskle

Overlay inspection info in VBAI running in Labview

Similar Messages

Maybe you are looking for