OVM 3.2 enable to boot PVM Windows guest via NFS

Hi all,
I am currently trying to create a Windows 2k8 PVM guest. I have extracted the ISO file on the OVM manager and ensured that NFS is currently running. I edited the /etc/exports file to point to the extracted folder with RO permissions.
When I attempt to boot to the nfs network path on the VM I am getting "Error: Boot loader didn't return any data".
Any ideas if I am missing something for these guests to boot to the NFS share?
Thanks!

Thank you for the reply budy!
After talking with our development team, they had brought that to our attention. I am new to the OVM world and currently building new environment for our entire department so I wanted to make sure everything was build to handle the high processing and I/O requirements necessary.
Cheers!

Similar Messages

  • Thinkpad T520 - 4239CTO cold vs warm boot menu (Windows 7 Pro)

    I have a curious situation. I replaced the hard disk in the above named Thinkpad with and Intel 530 SSD (250 MB). The OS is a fully patched Windows 7 Pro. Just for the record, to ensure full details are revealed: The new disk was, as recommended on the Lenovo site, activated as a GPT disk, the original was MBR. The BIOS option is Legacy boot (MBR) or UEFI (no MBR) or both. If I selected the UEFI only, I could not boot to or install the OS from the recovery disks. If I selected both, with legacy first or UEFI first, the recovery DVD's would boot and the inbstall would proceed without issue. This si where the trouble starts: Upon completion of the install, a number of anomalies appear. Regardless of the legacy/UEFI setting on the BIOS, if I warm boot, the options menu appears (tabbed with boot options and application options). I have no way out of this as another warm boot just returns me to that menu. If I cold boot, the proper boot sequence occurs and Windows loads properly, but only if the BIOS is set to BOTH for Legacy/UEFI. If it is set to either Legacy only or UEFI only on a cold boot, I get the option menu with the boot/applications tabs but the applications tab now includes the BIOS menu. If I cold boot with both Legacy and UEFI enabled, it boots to Windows and disk manager reveals that the disk is GPT but it appears to have an MBR. My conclusion is that the BIOS is confused because the disk is in some sort of amorphous MBR AND GPT state or something. I am concerned about aggressively pursuing one path or another (forcing a GPT disk by removing the MBR, for example) and getting into more trouble. I wonder if the Lenovo factory recovery disks are incapable of installing on a GPT disk and if that is the issue. Any comments or help is appreciated. Thank you

    Hi Ran,
    Thanks!
    I haven't tried it yet.
    In the meantime i did more testing and found out that even with only Power Manager version 2.41a installed the latest Intel Pro wireless driver also supported by lenovo is not stabel and FN-F5 or windows network connection also fails to switch the radio back on after a reboot when the radio has been turned off first ;-(
    Reading http://www-307.ibm.com/pc/support/site.wss/document.do?sitestyle=lenovo&lndocid=MIGR-67283
    over and over I decide to revert back to the old Intel wireless driver listed on this page.
    http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-67256
    Reinstalled ThinkVantage Access Connections for Window Vista version 5.12
    I tested it again........ IT WORKS!!!
    Please try this combination:
    BIOS Version: 1.15
    Bluetooth with Enhanced Data Rate Software II for Windows Vista Version: 6.2.0.5000
    ThinkVantage Active Protection System for Windows Vista 32-bit, XP, 2000 Version: 1.62
    ThinkPad Power Management driver for Windows Vista, XP, 2000, Me, 98 SE Version: 1.52
    ThinkVantage Productivity Center Pack Version: 3.02
    Power Manager for Windows Vista Version: 2.41a
    ThinkVantage Access Connections for Windows Vista Version 5.12 !!
    Intel Wireless LAN (11abgn, abg, bg) for Windows Vista 11.05.0 API
    Regards,
    Ritchy
    Message Edited by Ritchy on 01-14-2009 11:56 PM

  • Installing PVM via NFS

    I'm trying to create a PVM Windows machine using NFS in 2.2 and for some reason it's not working. Was this functionality changed in 2.2?
    What I've attempted thus far:
    virt-install os-type=windows os-variant=winxp -p -lnfs:10.0.0.32:/media/winxp -s5 vcpus=1 ram=1024 -nwinxp_test file=/OVS/running_pool/winxp_test/System.img vnc
    Starting install...
    ERROR: Invalid NFS location given: [Errno 2] No such file or directory: '/var/lib/xen/xennfs.PiRhvE/images/xen/vmlinuz'
    This is the same if I try to install via the VM Manager as well. I have tested the NFS mount and can verify that it's working correctly.

    npawelek wrote:
    They're asking me to add an NFS repo to the VM Server, thats why I was asking if something has changed, because the documentation looks the same from the PVM install standpoint from 2.1 to 2.2.Keep in mind that you cannot install Windows as a PV guest, only an HV guest. Windows does not support paravirtualization.

  • Windows 8.1 Ent eval enabled Secure Boot I think

    I want to get my laptop back to its original format.
    Currently dual booting Windows7/8.1
    During the installation of Windows 8.1 Enterprise evaluation it paused to say it was going to enable secure boot.  I did'nt think much of it I thought I could change it back from the bios.  Did it flash my firmware?  I checked the system status
    with msinfo32.exe; was legacy mode and with powershell; secure boot not supported.  I don't have any options to disable secure boot in the bios nor from within Windows -"I know how to disable it in windows 8.1".  I can't boot a foreign
    operating system, but I can boot a Microsoft OS which sounds like secure boot to me.  I want to get it back to running Windows 7 dual booting with Linux.  I use both at work and need both.  I made the mistake by loading the Eval on my primary
    laptop.  I read I need to revert back to Windows 7 completely, formating and re-installing the OS.  Will this clear my secure boot simulation issue?  I have not changed the partitions or removed any O/S's.   What's the best way
    to proceed?

    Hi,
    I want to explain that, Secure Boot is indepent with system, you can disable it in UEFI interface.
    To disable Secure Boot, you can follow the steps below:
    1.Before disabling Secure Boot, consider whether it is necessary. From time to time, your manufacturer may update the list of trusted hardware, drivers, and operating systems for your PC. To check for updates, go to Windows Update, or check your manufacturer's
    website.
    2.Open the PC BIOS menu. You can often access this menu by pressing a key during the bootup sequence, such as F1, F2, F12, or Esc.
    Or, from Windows, hold the Shift key while selecting Restart. Go to Troubleshoot > Advanced Options: UEFI Firmware Settings.
    3.Find the Secure Boot setting, and if possible, set it to Disabled. This option is usually in either the Security tab, the Boot tab, or the Authentication tab.
    4.Save changes and exit. The PC reboots.
    I found an aticle that teach how to install dual-boot Windows 7 and Ubuntu 12.04 on a PC with UEFI hardware:
    http://www.linuxbsdos.com/2012/10/11/dual-boot-windows-7-and-ubuntu-12-04-on-a-pc-with-uefi-hardware/
    Hope this helps.
    Roger Lu
    TechNet Community Support

  • My HP Pavailion 15-n020tu Stuck at Booting in Windows 8.1 Pro when I enable Hyper-V?

    Hi,
    I'm using HP Pavailion 15-n020tu Stuck at Booting in Windows 8.1 Pro when I enable Hyper-V. And I have to enable Hyper-V to test my Windows Phone Apps in MS Visual Studio? Mty friend Dell Laptop does not facing this problem with same configuration which I have. Then why me are facing this problem?
    Help Me?
     I tried on Windows 8 Pro but again same problem. 
    So many things I tried updating Windows, Updating drivers but failed.

    Hello @Vikas_Kumawat80,
    Welcome to the HP Forums, I hope you enjoy your experience! 
    I understand that you are looking to enable Virtualization on your notebook computer, and I would be happy to be of assistance!
    While I do not have any experience with Virtualization, I do recommend taking a look at this resource on How to Enable and Use Client Hyper-V, as well as Run virtual machines on Windows 8.1 with Client Hyper‑V. I am not certain if this processor has hardware virtualization support, it appears that Windows 8.1 pro and enterprise may have built in capabilities.
    If you require further assistance on this, you might have to contact Microsoft on the topic.
    I hope this helps!
    Best Regards
    MechPilot
    I work on behalf of HP
    Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
    Click the “Kudos, Thumbs Up" on the right to say “Thanks” for helping!

  • Windows Guests - OVM vs VMware?

    Which one is the best for Windows Guests? Is it OVM or VMware. I have heard from one of my customer that Windows guests on OVM show poor performance esp when it is run over NFS volumes. The performance would be better using VMware.
    In our environment, there are some Windows guests deployed in OVM using LUNs. I would like to know what specific combination gives good performance(at least no slowness) for running RDBMS, and other applications in the Windows Guests. I would like to promote OVM over VMware.
    My typical deployment would be - a 32/64 bit Windows 2003/2000 server guests running off an NFS volume backed block device. The RDBMS and other middle tier will also come from the same NFS volume probably with a different disk file attached.
    I read in the documents that Windows guests cannot be created with paravirtualization enabled. In that case, what would be the purpose of Oracle VM para-virtualized drivers for Windows? Does installing Windows using hvm require para-virtualized drivers?

    An ordinary install of Windows on OVM will show inferior performance because it will be running in fully-virtualized HVM mode. To get optimal performance, you need to install the para-virtualized device drivers and reconfigure for PVM mode.
    Get the instructions and drivers from http://download.oracle.com/docs/cd/E11081_01/doc/doc.21/e15298/toc.htm site. Or, to bypass all the verbiage, fetch the drivers from the edelivery.oracle.com site.
    Using these PVM drivers will make a significant difference.

  • HP Envy 700-430qe DT CTO - - - Trying to dual boot with Windows 7

                                                                                                       HELP HELP HELP
    I know how to set up double boot for several different HP computers, based mostly from what I have learned in this great forum, but this one has me stumped.
    I have been trying to install Windows 7 on this computer to double boot with Windows 8.1. I have tried to set the bios up correctly, enabled legacy, disabled secure boot, disabled fast boot. I booted under UEFI  to get in to GPT mode, still no luck at all.
    The installation always goes all the way through the first 4 steps and through most of the 5th.  After the reboot in the 5th step, it stops and can not go any further. A message appears without any error code. 
    I think it may be a problem in this computers UEIF  settings, but I do not know if anymore of them to try.
    I can use all the help you all can offer.
    Thank, Brad
    PS, If we ever get this to work, then I will have to ask you where to find drivers for this model, if they exist!

    Hi Brad,
    According to the information that you posted you have a W8 delivered PC.
    If the graphics card in your PC can run in legacy mode then you should be OK.
    I suggest that you use a separate HP for W7 as you will probably run into partition placement issues when you try to install W7 to the same HD. Installation to the same HD is not impossible but you will have to remove some partitions such as the recovery partition and then resize the "C" partition to make room for W7. You should be able to use Disk Management to delete partitions and resize the "C" partition.
    Be sure to create the external HP recovery media as it will be needed. Backup your data to separate external media.You should also consider installing the HP diagnostics to an external flash drive.
    Boot in the BIOS and set the BIOS to legacy mode and fast boot off.  Save the changes on exit.
    Now boot up the external recovery media (don't select the EFI media if shown) and reload your PC with W8.
    If your PC boots up and runs OK then you should be good to load W7.
    If you are using a separate HD for W7 then unplug the original HD.  If you don't then W7 will install a boot manager to the primary HD.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • How can enable switchable graphics in Windows 8.1 (Bootcamp)

    So I just dropped $3,000 on a high end (late 2013) 15" rMBP and immediately installed Windows 8, and then 8.1, through Bootcamp. I need Windows for a lot of engineering programs, as well as occasional gaming. I bought a MacBook because I prefer OSX for programming - I love Ubuntu, but my previous laptop had driver issues (ironically enough, also due to the graphics card) that would cause it to overheat and only give me about 45 minutes of battery life.
    After using it for a little, I realized that the MacBook was VERY hot. I closed all of the power intensive applications and proceeded to browse reddit on low brightness and power saving settings to let it cool down, but it did not cool down much. I shut it down, and turned it on about 15 minutes later, when it had successfully cooled down. I realized that just being booted into Windows caused the laptop to get unreasonably warm - I'm assuming that it's because I have the Nvidia GeForce GT 750M graphics card in it. I can not seem to find an option to enable power saving graphics.
    Is there any way to use the integrated Intel graphics rather than the discrete card? Not being able to run Windows reasonably well would really make me regret this purchase, especially when I could have bought a different laptop for much less and installed a Linux distro on it.
    Any help is appreciated.

    Sorry, but I think the above post is bad advice.  It's unlikely to be a fan issue as these are generally controlled by firmware.  If your laptop is getting very hot in Windows with only minimal and light use then that suggests a power management issue.
    The first thing you'll want to do is check that your Power Management settings are not set to "High Performance".  A lot of people select this option thinking it gives them the most out of their computer and hardware purchase without realising what it does and that it comes with significant issues and tradeoffs.
    What the High Performance setting does is disable CPU throttling, forcing the CPU to run at its maximum speed constantly (on all cores) and draw its maximum power load, even when not required.  This causes the laptop to heat up very hot very quickly even if you aren't doing much, while simultaneously killing battery life.  If you found a way to replicate this behaviour in OS X (and turn graphics switching off) you'd find the laptop would get equally hot and fans would ramp up to maximum speed just to try to keep things cool.  If you hear your fans spinning at maximum then that is evidence that fan control is working.
    It's a very unnatural behaviour and there are almost no situations where you ever need to use it.  Microsoft should really make an effort to hide it and make it harder to access.  High performance sounds nice and "Why wouldn't I want my laptop to run with high performance" is what most people think.  Of course, Microsoft isn't very good at understanding what people think.
    For most purposes "Balanced" is the Power management setting you'll want to use and this more closely reflects what Apple uses in OS X.  Failing this, it could be that whatever software you're using is very badly coded for power management, but this is less likely and unlikely to cause the severe heating issue you described.
    Finally, there's no need to regret your purchase.  It's an amazing laptop and the best way to run Windows in my opinion.  The only thing missing I can think of is switchable graphics driver support but this isn't anywhere near as severe a problem as what you've described.

  • H9-1150 PC wont Boot with WIndows 7 Premium 64 bit with ASUS 960 GTX Card.

    I saw others have posted simular issues but i thought id repost this again in case there is more help.  I have the Pavalion Elite Phonix h9-1150 desktop with Windows 7 Home premium 64 bit.  and the HP 7.07 bios (seems no way to upgrade  the bios).
    The issue is like others have had i install the new graphics card the Asus 960 GTX Card which came out last month and the system starts up  gives about 3 beeps in about 30 seconds each and then it goes to a black screen with a blinking curser and nothing else happens. cant enter bios or  the HP settings..
    I did try to disable UEFI boot devices in the bios settings and only enable legacy devices (after switching back to my original card then switching to the new card) but it still gives the 3 beeps upon booting.   However i was able to enter windows. though i think it may be due to shutting off the computer with the old card in without powering down first. and  after the 3 beeps happens (which still locks you out of the bios menu) it shows up the window where you can select safe mode or normal mode.. as sometimes happens if you boot up your computer with windows 7 if you had just turned it off without powering down or something.  Through that i am able to enter windows and run the PC and graphics card with no issue its just when i try to boot the issue happens.
    and No HP suppor it is NOT a defect with the Card itself. Like many before. i bought a EVGA Card a while back a 780 GTX and the SAME issue happend (though i didnt try the removing the UEFI boot devices then) ...
    There is a spacific issue with HP computers that seem to lock out "new" hardware from booting.
    Honestly ill be blunt. I really think this is poor doings I read somewhere that while HP will never state it they do this on purpose to prevent people messing up warrenty or any "liabity" occuring by people installing other hardware onto HP stock computers
    that makes no since to me.  the PC SHOULD be able to run the card. in fact its running it now once i was able to bypass the lock out (temporarly)  check benchmarks everyhting is fine the card runs 3 times faster  then the old one (as should be the case).
    But its just this lockout that HP for some reason has installed on their bios/motherboards that is the issue.
    Good news is i got it from amazon and i have about a month till i have to return it. which i think this time i will do.  to see if anything crops up in a month or something.
    The ONLY solution it seems HP offically has is that to disable secure boot under windows 8
    but this is not a windows 8 computer. and i do assume even if iINSTALL windows 8 . the issue would not go away because since its an older bios there would be no way to have a secure boot option to remove?
    HP you really need to get on the ball and give us a direct reply on this.  Is there ANY WAY to fix this? Can you not simply  make a update of older bioses to allow this? Or do you just not want to worry about older pCs?
    either way i think this is wrong and very frustrating and to be honest. If this is the case when my pc otherwise SHOULD run the card
    its a PCI express 16x slot that is 3.0
    here is the deetailed specs as per your page
    http://h20564.www2.hp.com/hpsc/doc/public/display?docId=c03273835
    the card SHOULD WORK fine.  I thought the 780 GTX was a bit too much for the PC as it had more then a six pin port and needed a bit more power so at first i thought that was the issue. so i returned it. and got this new card now.
    however the ASUS 960 GTX card requires the SAME power supply as the default GTX 550 Ti card and the SAME SIX PIN connector
    so it SHOULD work.
    and benchmarks show that it DOES its just the stupid bios ..that is having the issue.
    i am afraid to power down the computer at the moment and try again to see if windows boots normally after disabling the UEPI boot devvices because it may not boot  properly.......
    HP you are one of the biggest suppliers of computers you know technology these are YOUR computers.  WHY cant you give us a direct awnser over this.
    ITS VERY frustrating
    and to be honest if i cannot resolve this issue i am very hestient to ever buy another HP product if their computers spacifically have this new hardware lockout mode.
    because i have the card running now on my pc it runs great! 3 times faster as it should! and yet i know in the back of my mind if i cant figure out this issue likely ill just have to send it back.........least i have some time.
    and right now i dont have the money to buy a new pc . this PC is JUST fine for what i need for now other then wanting a bit better card...
    it shoudnt be this much of a hassle should it?
    Thank you.
    This question was solved.
    View Solution.

    Hi,
    You need the BIOS update that is listed under Windows 8 in order to support the newer graphics.   You need to upgrade to Windows 8 or temporarily install Windows 8 so that you can install the BIOS update.  While there may be other ways to install the BIOS update, clearly having Windows 8 running will be the safest way.  The version 8 BIOS is your best chance at getting the newer graphics cards to work.
    You can trial Windows 8 Enterprise for 90 days.
    If you decide to install W8, then create the HP external recovery media and backup your data before you do anything.
    The reality is that there is no guarantee that any particular graphics card will work in any particular PC even if the graphics card works in other PCs or even the same or similar model PCs. Know what the return policy is before you buy.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • Can't boot into Windows 8 Single Language 64 bit or access the BIOS screen with the F1 key

    I have in my possession right now a Lenovo E49, Model name: 3464
    I am unable to access the BIOS settings at POST by pressing the F1 key.  Neither does it respond to the Enter key when it displays the message "To interrupt normal startup, Press Enter".  I am also unable to boot into the installed OS Windows 8 Single Language 64 bit.
    For your informtion, these are the events that led to this issue.
    I accessed the BIOS settings at startup using the CHANGE PC SETTINGS option in the CHARMS menu in Windows 8 Single Languge 64 bit followed by GENERAL and ADVANCED STARTUP.  Then I chose Restart Now.  Windows restarted to produce the startup screen where I chose Troubleshoot, followed by Advanced Options and UEFI Firmware Settings, followed by Restart.  This took me to the BIOS settings screen. Once there I changed the boot settings in BIOS so that SECURE BOOT was turnned OFF.  It was in ON state prior to that.  I also changed the BOOT MODE to LEGACY ONLY.  I also changed the BOOT ORDER to boot from DVD drive first followed by the Hard Disk and USB Hard Disk.  I saved the changes by pressing F10.
    Now the computer is able to boot from the DVD Drive.  I tested this by inserting a Windows 7 Repair DVD and also a Linux Live DVD.  Mind you, I didn't mke any changes to the Hard Drive.  I'm also able to boot from a USB Hard Disk.  This too was tested by inserting a bootable USB HD that had both Windows 7 and Windows 8 OS installers.  I used only the command prompt feature in the Repair option on the Windows 8 installer to ensure that I could access the partitions on the HD.  I did not in any way install Windows 7 or 8 on the HD.
    If there is no bootable DVD or USB HD inserted, the laptop is involved in a loop that restarts followed by a message that says the following:
    "Intel Undi, PXE-2.1 (build 083)
    Copyright (C) 1997-2000 Intel Corporation
    This product is covered by one or more of the following patents:
    US5, 307, 459,  US5, 434, 872,  US5, 732, 094,  US6, 570, 884,  US6, 115, 776 and US6, 327, 625
    Realtek PCIe GBE Family Controller Series v2.41 (06/08/11)
    PXE-E61: Media test failure, check cable
    PXE-M0F: Exiting PXE ROM."
    I am positive that the current state of the BIOS is such that it does not accept any input keys like F1 and F12 at POST so that the BIOS can only be accessed through Change PC Settings in Windows 8 as I had done prior to the occurence of the issue.  Since I cannot boot up Windows 8 I cannot use this method to access the BIOS.  And since it is not possible at this stage to access the BIOS settings through the F1 key, I believe Lenovo must have surely provided another alternative to enter the BIOS.  Can you kindly tell me what other way is there to do this.  In earlier days, one could reset the BIOS by shorting the BIOS through pins on the motherboard.  Is that possible now?  Or is there some Lenovo BIOS utilily that enables me to change the BIOS setting to boot with Legacy and UEFI?  Or do I have to install Windows 8.1 64 bit in Legacy mode?

    I'll see if another member of the team can jump in here and offer more help...
    What I might imagine is that you can only access BIOS from a cold boot. Windows 8/8.1 have hybrid shutdown and don't completely shut down the machine normally, so even when it powers off, it isn't fully off and the next boot is not really a cold boot.
    Please see this KB.  I realize this assumes you can get into windows.
    As you suggest, it also seems as though you have set legacy vs UEFI and that may be why your drive is not currently booting.   Can you remove the battery on your system?  If not, is there a reset hole on the bottom?  Removing battery and AC and pressing and holding the power button several times, then re-attach AC and Battery and try to restart and press F1 to get into BIOS.  (Not familiar with models that use enter for BIOS).
    Mark
    ThinkPads: S30, T43, X60t, X1, W700ds, IdeaPad Y710, IdeaCentre: A300, IdeaPad K1
    Mark Hopkins
    Program Manager, Lenovo Social Media (Services)
    twitter @lenovoforums
    English Community   Deutsche Community   Comunidad en Español   Русскоязычное Сообщество

  • Can I use my Intel-based MacBook to boot into Windows 7 from an external HDD?

    Okay, so I need to use Windows for some simple applications. Problem is, I don't have a Windows desktop anymore and while I have both Windows and Linux partitions along with Mountain Lion on my installed hard drive, I'm probably going to wipe said drive and just use the entire partition for Mountain Lion. That said, I'd like to use an extra hard drive I have lying around to boot Windows.
    My questions are:
    1. Does my MacBook support USB boot to Windows?
    2. If my laptop does support this, can someone point me to a set of good reliable instructions to install Windows onto the external hard drive and boot into it by USB?
    Thank you; have a blessed day!

    You seem to have a triple boot system that was done using the 10.6 installer disk and a copy of rEFIt.
    I know because I had the same thing once.
    I can tell you what will happen if you decide to upgrade 10.7 or 10.8
    1: The EFI and GUID is going to change, rEFIt hasn't been updated in ages since 10.7 started rolling out back in about June 2011. There will be adverse effects with rEFIt so I hear.
    2: The 10.8 upgrader is going to barf at your triple boot system, it will upgrade the 10.6 partition but warn you that the 10.8 RecoveryHD partition (10.7 and 10.8 both install) that it normally installs at the very bottom of the drive will not be installed and you can't enable Filevault.
    Intel Mac's can have only 4 bootable partitions on the drive, the 10.7+ installer is normally dealing with EFI, MacintoshHD, BOOTCAMP, RecoveryHD. It barfs at anything else it doesn't understand and will not install RecoveryHD partition, which on a non-Internet Recovery capable hardware is required to reinstall the currently upgraded OS X operating system version. But you can always go back to the 10.6 disks and wipe and restore that way or via 10.6 USB boot key.
    http://www.maciverse.com/install-os-x-snow-leopard-from-usb-flash-drive.html
    So with 10.7+ you'll have to use something like Carbon Copy Cloner for the OS X partition.
    So since rEFIt is going to be hosed, so will your ability to use the EFI based program to boot into the three operating systems at boot time.
    I assume you found this out and why you want to dump Windows on a external drive. However Apple's EFI doesn't recognize Linux as a boot option.
    There is a rEFIt fork that will allow Linux to boot on a Mac: http://www.rodsbooks.com/ubuntu-efi/index.html
    Windows as you now know can't be booted off a external drive, however if your use of it is minor, you may want to consider using a virtual machine to run it in OS X or Linux instead using the free VirtualBox.
    Windows in BootCamp or Virtual Machine?
    You should Carbon Copy Cloner the OS X 10.6 partition to a external GUID OS X Extended J (JHFS+) drive.
    You can use WinClone 3 in OS X to clone the Windows partition to a external drive, but it's a backup only, no booting capability. Restoring it will boot on the internal drive of course.
    Linux you should already know how to clone it to a external drive using dd.
    I advise you use the 10.6 install disks to set up your new partition scheme, but your going to have to uninstall rEFIt and return the machine and firmware back to basic Apple factory system as possible before doing anything.
    EFI doesn't get erased, it resides in NVRAM and the EFI partition, controls the at boot key commands to boot off OS X install disks, so it's important to uninstall rEFIt completely before upgrading OS X.
    If the Windows version your using is XP, to install that first using BootCamp in a fresh 10.6 install and reverse clone using WinClone before upgrading to 10.7 or above. It will be grandfathered in, but can't be reinstalled later.

  • Dual-booting with Windows 8, Arch Linux first?

    I initially had Windows 7, then Arch. Now, I have a key for Windows 8. I can just upgrade the previous Windows 7 partition, but I only allocated 37 GB originally, so I want to expand it - I would therefore need to delete the partition and make a new one. However, dual-booting guides say that Windows should be first. What is the best way to go about this?

    srs5694 wrote:
    x33a wrote:Thanks, that's interesting. I always thought that it didn't run without secure boot.
    Note that Secure Boot is NOT synonymous with EFI. Secure Boot is one optional feature of EFI. In fact, of five computers I've got that use EFI, only one supports Secure Boot.
    I did know that
    Microsoft requires manufacturers to ship their computers with Secure Boot enabled in order to get a Windows 8-compatible sticker. Because most manufacturers consider the lack of such a sticker to be the kiss of death for their products, this means that nearly all computers that ship with Windows 8 ship with Secure Boot enabled. Because Secure Boot is an EFI feature, this means that these computers also use EFI.
    This does not mean that Windows 8 itself requires either EFI or Secure Boot; the requirement is a marketing requirement for new computers. If you buy a Windows 8 package at the store, it will install on an older BIOS-only computer (assuming it's not too old), on an EFI computer that lacks Secure Boot support, on an EFI computer with Secure Boot support but with that feature disabled, or on an EFI computer with Secure Boot and Microsoft's keys enabled. (It is possible to replace your firmware's Secure Boot keys, which would prevent the installation of Windows unless you re-signed the Windows boot loader yourself.)
    Note also that it's possible to switch Secure Boot on and off, at least on x86-64 systems. (Microsoft's Windows 8 sticker requirements specify that users must be able to do this on x86-64 systems; but on ARM computers, Microsoft's sticker requirements say that users must not be able to disable Secure Boot.) Windows 8 should continue to boot when you turn Secure Boot on or off; however, some versions of GRUB have problems chainloading to other EFI boot loaders (including the Windows boot loader) when Secure Boot is enabled.
    Thanks, that's very informative.

  • How do I toggle num lock in Windows 7 via Boot Camp 4.0 on a MacBook Pro (Late 2011)?

    Is there a keyboard shortcut to enable num lock on the MacBook Pro 2011 (Late) in Windows 7 via Boot Camp 4.0?  I have a mouse with a numpad mapping on the side of it.  When I press the number keys, the cursor responds in the way one would expect it to with the num lock off (ie, 6 moves it right, 4 moves it left, etc); however, I need to use it to produce numbers. 
    I have read http://support.apple.com/kb/HT1220, which covers the previous MBP keyboard (on which the F6 key function was numlock), but I can't find any information regarding the possibility of doing this with the new MBP model keyboard (on which the F6 key function is increasing the keyboard backlight).  Any thoughts?  Suggestions?

    I was looking for this answer and found it on another site. I realize this is an old thread, but just in case someone else stumbles here and needs to do it, here's how to turn numlock on or off in Windows, and to make it stick:
    Run Registry Editor (RegEdit)
    In Windows 8 or earlier you can press Command-R, then type regedit
    In Win7 or earlier, you can also just click Start menu, and type regedit in the search field.
    In the Registry Editor, navigate to HKEY_CURRENT_USER -> Control Panel -> Keyboard
    Within the Keyboard folder, you should have an entry named InitialKeyboardIndicators. Set the "Data" value accordingly:
    0 = Num Lock is turned OFF after login
    1 = Disable Num Lock
    2 = Numlock is turned ON after the login
    I hope this helps.

  • Can't boot from windows 7 usb installation media

    When trying to boot from windows 7 usb installation media no efi boot option availiable. Using "boot from efi file" option whith each and every .efi file on installation media results in a message saying "The selected boot device failed. Press <Enter> to Continue". 
    USB installation media created using original windows 7 iso image and couple diskpart commands(resulting in clean flash storage with a single active primary partition) plus simple copying of the iso image's contents on usb flash. 
    Enabling/Disabling SecureBoot doesn't have any impact whatsoever. 
    Installation boots from aforementioned media successfully when CSM enabled, though i would really prefer installing Windows 7 in uefi mode. Which microsoft claims Windows 7 supports. 
    Any help or suggestions would be much appreciated. Thanks in advance. 
    PS: my disappointment in this particular HP notebook is unspeakable. Aside from issue of the current topic, It keeps defaulting to windows boot manager when dual-booting windows & linux no matter what i do, and windows 8.1 Pro is constantly BSODing whenever i try to run fullscreen games on high-performance GPU whith every graphics driver i could possibly install (including both hp's own and amd's). Found silly workarounds for both of these issues, however still hate HP treating it's customers that way.

    Booting from USB 2.0 port or DVD with SecureBoot disabled gets me to a screen saying "starting windows", just before the actual setup begins and then system simply hangs. Still unable to install. Thanks for your suggestion though.

  • Problem with iWeb Quicktime page using Boot Camp Windows XP

    I used iWeb '08 to create a one-page web site with a short QuickTime movie (.mov file). The movie plays fine in Mac OS X Safari. I have a Windows XP Boot Camp partition, and when I boot into Windows and load the web page using Internet Explorer, the movie will not play. It gives a plug-in error and the browser crashes. The same thing happens with Windows Safari. However, the movie plays fine using Windows Firefox.
    Is this an iWeb problem or Boot Camp problem? I don't have access to a straight Windows PC. An suggestions will be appreciated. The URL for the web page is:
    http://www.hearnweb.com/avian/

    The problem was a setting in QuickTime. I enabled "Safe Mode" in the Advanced tab of QuickTime Preferences, which did the trick.

Maybe you are looking for