Parallel port cvi 9 XP

Hello All,
Has anyone had any luck with direct IO inp and outp access to the parallel port using CVI 9 under XP 32?
I tried it using the parallel.zip example provided by NI and found it did not work.
Thanks!

lunchbreak,
Just out of curiosity, what operating system are you using. The parallel.zip example was written using CVI 5.5 and the parmon.exe attached appears to only work in Windows 95 and 98. Also, I downloaded and ran the example in CVI 2009 and was able to run it fine. I was able to write a value to the port and read the value back correctly. Are you getting some sort of an error when you run this example?
Raj
National Instruments
Applications Engineer

Similar Messages

  • Parallel Port under CVI

    Hi,
    is it possible to write to the parallel Port or to other
    adress ports under Win95 or WinNT with CVI ?
    Do you know a good book about that subject ?
    thanx.

    Yes, CVI has a kernel mode driver (cvintdrv.sys) which loads automatically when the CVI environment starts. It enables Port I/O under NT (95/98 aready allows it)
    a good reference on the parallel port:
    www.beyondlogic.org
    a good book on the parallel port:
    Parallel Port Complete
    by Jan Axelson
    www.lvr.com

  • Reading/writing to parallel port LabVIEW 7.0 Win2000

    I'm using LabVIEW 7.0 on a Windows 2000 machine which also has the CVI runtime engine version 6.0.4.105.
    I wish to write to the parallel port, simply on/off signal to eight lines. I have previously done this with LabVIEW 5+Win98. I have downloaded the accessHW libraries and installed them but have discovered that I also need the CVI rte version 5.0 . When IT personnel try to install this run time engine "A newer version of this run time engine is currently installed"
    appears and won't install version 5 over version 6. Has anyone else come up against this and is there a way around this (without having to install an older version of LabVIEW)?

    Leeser wrote:
    > I'm using LabVIEW 7.0 on a Windows 2000 machine which also has the CVI
    > runtime engine version 6.0.4.105.
    > I wish to write to the parallel port, simply on/off signal to eight
    > lines. I have previously done this with LabVIEW 5+Win98. I have
    > downloaded the accessHW libraries and installed them but have
    > discovered that I also need the CVI rte version 5.0 . When IT
    > personnel try to install this run time engine "A newer version of this
    > run time engine is currently installed"
    > appears and won't install version 5 over version 6. Has anyone else
    > come up against this and is there a way around this (without having to
    > install an older version of LabVIEW)?
    You could also use the PortIO library from the OpenG project
    http://www.openg.org.
    It is currently only in the CVS source code
    repository on that site and not yet part of the OpenG Toolkit. Because
    it is not everybodys thing to use CVS I include that library as
    attachement here.
    I tested it myself on Win95, NT4, 2000 and XP and had no problems at all
    with it. But please consider it beta software and if you have problems
    let me know with as much details as possible.
    Rolf Kalbermatter
    Rolf Kalbermatter
    CIT Engineering Netherlands
    a division of Test & Measurement Solutions
    Attachments:
    portio.zip ‏195 KB

  • Parallel port / NT 4.0 / Labview 5.0

    How can I control the parallel port i/o pins with labview 5.0 and NT 4.0 ?
    The sub.vi "out.port" doesn't work.
    Thanks for any advice
    Andreas

    I use a DLL that was written in CVI to control the parallel port. CVI
    drivers for Inport and out port will work under windows NT. This is not a
    fast solution but it does work.
    Also a long time ago (In a galaxy far far away) there was a canned Import
    and outport DLL that worked with LabVIEW under Windows NT on Nationals
    Instruments web site. If you cannot find it, I could email you the dll I
    wrote but it is designed to work with EPP printer ports.
    From John Harmon
    Web Page: www.bright.net\~harmonj
    Email: [email protected]
    Land Line: 330-848-0460
    Pager: 330-490-0091
    ==========================================
    Andreas Balzer wrote in message
    news:[email protected]..
    > How can I control the parallel port i/o pins with labview 5.0 a
    nd NT 4.0 ?
    > The sub.vi "out.port" doesn't work.
    >
    > Thanks for any advice
    > Andreas
    >
    >
    >

  • PC parallel port access with XP

    I recently got In Port and Out Port working on XP.
    I searched the ni site for AccessHW. The CVI Run Time Engine has to be
    version 5.510 or earlier. I checked the version number of one file, i.e.
    cvirte.dll to verify.
    I directed the installer to install accesshw to the directory where the new
    In Port and Out Port and the rest of the new parallel port .vis were going
    to be, i.e. Labview\Labview 6\vi.lib\platform.
    I downloaded parallel.zip from ni.com and moved the parallelnt.llb file to
    this same directory. Parallelnt.llb has a number of parallel port vis, not
    just replacements for In Port and Out Port. I replaced the In Port.vi and
    Out Port.vis in the diagrams I was trying to make work with the new .vis.
    So, on this XP machine, with
    a monitor program, parmon.exe, running to
    display the bits on the parallel port, Labview can be seen to be using the
    new parallel port .vis, and, bits on the port are changing.

    I wonder if there's a reason why there's a javax.comm 3 series for *nix, but not for windows. Hmmm.                                                                                                                                                                                                       

  • Problem with JNI and Parallel Port dll

    Hi. I'm doing some testes with JNI. Firs i followed the netbeans tutorial for doing a C programa that prints somthing for java.. like.. "Hello java from C".
    So i tried to load a dll from my dll. Like, I have this dll to use the parallel port on windows Xp. So i created a dll to access it an comunicates eoth java.
    I did everything just fine.
    When I start my Java app, the first thing it does is to load this parallel port dll and configure the functions of it.
    After that .. I get this error
    EXCEPTION_FLT_STACK_CHECK (0xc0000092) at pc=0x0093d269, pid=2284, tid=3000
    Can someone explain why ?
    (Sorry if i wasn't clear enough, english is not my native language, so ask if you don't understand something.. )

    hi ,
    I met the same problem this morning, and searched the www.google.com in order to solve it, as a result, your article was shown on my screen. :)
    Till now I have read some technical information and solved my problems. Maybe the solution be useful to you:
    ==============================
    error message : (Environment : Tomcat 5, Windows 2003, Mysql5)
    2006-3-29 11:53:48 org.apache.catalina.core.StandardWrapper unload
    message: Waiting for 2 instance(s) to be deallocated
    ==============================
    cause: the number of connection to database exceeded.another word,too many connections.
    ==============================
    solution: close the connection when it becomes useless for your program. :)
    ==============================
    ps. Sorry for my weak English . hehe ....

  • Control parallel port (data and control lines)

    I need to control the output on the parallel port (LPT1) - Both data and control lines.  Once the data is written (Pins2-9), I then need to toggle the Sprocket signal (PIN1) - on the parallel port. The sprocket signal is also referred to as the Data Strobe Output.
    The required method is as follows:
    1. Lower the sprocket signal on PIN1
    2. Send the data (Pins2-9) and wait
    3. Raise the sprocket signal and wait.
    4. Repeat.
    I am looking for a method to control the data on LPT1 pins 2-9 and then be able to toggle PIN1 - Strobe signal - without the data falling from the other pins. What I have found is that whenever the state is changed on the strobe - the data that was written to Pin2-9 falls to zero. This will not work for my application - the strobe tells the hardware device that the data is ready. If it falls to zero when I toggle the strobe - that will not work.
    Regards,
    Guy

    Hello Adam,
    I am familiar with both references.  If you look more closely at the library reference - it allows me to communicate using VISA across the parallel port pins 2-9.  It does not permit direct communication to pin1 (the strobe signal) - property nodes don't allow the strobe to be refereced either (similar to control lines/signals for COM ports).
    Worse, I have also located examples using OUT PORT that does enable pin1 to be toggled.  The problem is, when those VIs are used, the data falls from the data pins when the strobe signal is written, even if its value is not changed.  For example, if the strobe is already high, if another high value is passed, the data falls from the data lines.  The other issue, when using VISA, as soon as the data is writen, the strobe signal automatically goes high even though I need a wait before setting the strobe high.  This is in complete contradiction to the second article you referenced which clearly discusses writing data to pins2-9 then taking the strobe high to indicate to the printer that new data is available.  It must be possible since this is the typical handshake.
    I am still looking for a more complete answer/solution.
    Regards,
    Guy

  • Parallel Ports vs. Trashing Printers

    Recently bought 3 new workstations:  2 w/Windows 7 - - 1 w/Windows XP Pro... Question is:  my old HP Laserjet 2100tn will not work with these computers due to their not being a paralel port on the back of the computer.  
    Do they make converters for the cables to make them work? Or is the printer basically worthless at this point?
    This question was solved.
    View Solution.

    You can purchase and install parallel port adapter cards and the printer will work. I can't specify which cards as you haven't stated what the specs are on your workstations. There are also usb to parallel port converter cables available.
    Best regards,
    erico
    ****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
    2015 Microsoft MVP - Windows Experience Consumer

  • Connecting a HP LaserJet 4000 parallel port to Windows 7 USB port

    I have been using a HP LaserJet 4000 via a parallel port for years on a variety of machines / Operating systems without issue. However, having purchased a new Laptop (Windows 7  64bit), there is no parallel port (unsurprisingly). So the question is 'How do I connect my legacy parallel printer to the USB port ?
    Regards
    John Bennett

    Hi,
    You need something like this:
      http://www.shopbot.com.au/pp-belkin-usb-parallel-printer-adapter-f5u002-price-106075.html
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How can I write to the parallel port using LabVIEW 6.0.2

    I have tried updating the labview.ini file and also using the parallel.llb available on the site. When I execute the program it gives me error 37 saying,"device not found". I am running this code on windows 98. I tried to use VISA write,serial port write (using port 10) but nothing seems to work. I also tried to develop a sample code using inPort and outPort, but no success, it is not able to read the data back from the parallel port, even if it seems (????i don't know any way to cross-check it though????) to write.
    Does anybody know the problem here?
    THanks.
    Pari.

    Thanks Brian.
    Well here is the next problem. I got a VI (attatched) off ni.com and it works fine on a windows98 platform. But quits working on NT.
    I can write perfectly (which i checked by hooking an LED display unit at the other end of the parallel port cable). I observed that the LEDs respond to the toggling of individual bits (data bits). But the error occures at the "out port.vi", when I try to run it on a NT machine (where I actually wanna use it). Are you aware of any changes to be made in order to run a VI on NT that works on 98?
    Thanks again.
    Pari.
    Attachments:
    parallelPortSwitcher.vi ‏124 KB

  • How to Install a parallel port printer to usb port of Pavilion dv5 Notebook

    In trying to install my HP DeskJet 610C Parallel Port printer to my HP Pavilion dv5-1235dx Notebook PC with Windows Vista Home Premium 64-bit, I followed instructions given by HP Support some two years back.
    I connected up the two units through a Parallel-to-USB ports cable. The PC loaded and confirmed suitable driver. (Following advice from sites on the Internet, I have made repeated attempts to carefully install the printer, but to no avail).
    Upon my issuing the Print instruction, the printer invariably prints two copies of what appears to be 'gibberish' in two lines at the start of the sheet. Thereafter it picks up and then ejects 6-8 sheets of blank paper.
    Any help in resolving this anomalous situation will be be most welcome and much appreciated.
    I might add that the printer works normally when connected in parallel to an older, Compaq Armada 1750 Notebook (XP OS). In this instance too, the Parrallel/USB worked as in the Pavilion PC, above.  
    This question was solved.
    View Solution.

    Hi khalidem, 
    Sounds like you have a communication problem with the printer cables. Have you tried a new parallel to USB cable or adapter?
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as "Accepted Solution"

  • Using XP software with a parallel port dongle in windows 7 professional

    Please help...  Looking to have my parallel port dongle recognized for my older version software (XP) in Windows 7 under the XP PC mode.  Help in figuring out if LPT1 is set correctly or what I am doing wrong.
    Thanks

    Hello,
    I have W7 Professional 64 bit with Windows Virtual PC/Windows XP Mode installed. I have some older programs installed in XP Mode and they are working properly.
    Unfortunately, I have one older program that I currently have working on an older XP Machine and that program requires a Sentinel dongle to be seen on the LPT1 Parallel Port. Since my W7 computer has an LPT1 Header on the mother board, I have purchased and
    installed a PCI-Express Parallel Port and I have the ribbon cable connected to the LPT1 Header.
    After I enabled the parallel port in the bios, I could see LPT1 in the W7 Device Manager and in the Windows XP Mode Device Manager. However, when I click on
    Windows Virtual PC, highlight Windows XP Mode.vmcx and click on Settings, LPT1 does not appear.
    I have installed my old program in Windows XP Mode and it starts to run but, when it gets to the point where it must see the Sentinel dongle on the LPT1, the
    program does not find the dongle.
    I also purchased a Manhattan MHUSB to DB25 Parallel Converter and plugged it in. It said that it found new hardware and installed drivers for it but that didn’t
    work either.
    I am not married to any particular solution. So, I would use a USB Adapter or LPT1 connected to the mother board but there must be some code editing or changes
    in settings to make the dongle work in XP Mode.
    Can you tell me how to get W7 Professional 64 bit with Windows Virtual PC/Windows XP Mode to find the Sentinel dongle 
    on LPT1?
    Thank you,
    Dan
    Dan

  • Problem in sending data to parallel port

    Hello,
    I can open a parallel port (LPT1) using java comm api i,e javax.comm.
    but problem in sending data to parallel port,
    I choose the appropriate port(LPT1), it is in bi-directional mode according to BIOS configuration.
    but according to the java program the mode is SSP.
    when i write data to parallel port the volt-meter give a reading of high state for all data pin (pin1 to 9) i,e the parallel port doesnot change state. I am using windows XP.
    What is the solution?

    try it on Open Solaris 10 or Linux platform.
    also just try using the new FileWriter("LPT1").write("Hello");
    on windows platform
    Pravin

  • Sending trigger through parallel port, C++, Visual Studio 2010, Windows 7

    Hi, I have a problem that I am really stuck with, and I am novice to the task so any help would be extremely helpful.
    I an trying to write to parallel port on my PC in order to send a trigger to EEG recording machine every time the new goal appears in a Virtual Reality game that I wrote in C++ (I want to record EEG brain signals while subjects are playing the game).
    I tried to follow the instructions from here: http://msdn.microsoft.com/en-us/library/ff802693.aspx
    I wrote the following code:
    BOOL FileExists(LPCTSTR szPath)
    DWORD dwAttrib = GetFileAttributes(szPath);
    return (dwAttrib != INVALID_FILE_ATTRIBUTES && 
    !(dwAttrib & FILE_ATTRIBUTE_DIRECTORY));
    BOOL WriteABuffer(char * lpBuf, DWORD dwToWrite)
    OVERLAPPED osWrite = {0};
    DWORD dwWritten;
    DWORD dwRes;
    BOOL fRes;
    // Create this write operation's OVERLAPPED structure's hEvent.
    osWrite.hEvent = CreateEvent(NULL, TRUE, FALSE, NULL);
    if (osWrite.hEvent == NULL)
    // error creating overlapped event handle
    return FALSE;
    // Issue write.
    if (!WriteFile(ghComm, lpBuf, dwToWrite, &dwWritten, &osWrite)) {
    if (GetLastError() != ERROR_IO_PENDING) {
    // WriteFile failed, but isn't delayed. Report error and abort.
    fRes = FALSE;
    else
    // Write is pending.
    dwRes = WaitForSingleObject(osWrite.hEvent, INFINITE);
    switch(dwRes)
    // OVERLAPPED structure's event has been signaled.
    case WAIT_OBJECT_0:
    if (!GetOverlappedResult(ghComm, &osWrite, &dwWritten, FALSE))
    fRes = FALSE;
    else
    // Write operation completed successfully.
    fRes = TRUE;
    break;
    default:
    // An error has occurred in WaitForSingleObject.
    // This usually indicates a problem with the
    // OVERLAPPED structure's event handle.
    fRes = FALSE;
    break;
    else
    // WriteFile completed immediately.
    fRes = TRUE;
    CloseHandle(osWrite.hEvent);
    return fRes;
    I get none of the specified errors, but game fails to start and it seems nothing gets written to parallel port. Any suggestions on how to proceed from here would be more than appreciated.
    Thank you, Joanna

    Hi, I have a problem that I am really stuck with, and I am novice to the task so any help would be extremely helpful.
    I an trying to write to parallel port on my PC in order to send a trigger to EEG recording machine every time the new goal appears in a Virtual Reality game that I wrote in C++ (I want to record EEG brain signals while subjects are playing the game).
    I tried to follow the instructions from here: http://msdn.microsoft.com/en-us/library/ff802693.aspx
    I wrote the following code:
    BOOL FileExists(LPCTSTR szPath)
    DWORD dwAttrib = GetFileAttributes(szPath);
    return (dwAttrib != INVALID_FILE_ATTRIBUTES && 
    !(dwAttrib & FILE_ATTRIBUTE_DIRECTORY));
    BOOL WriteABuffer(char * lpBuf, DWORD dwToWrite)
    OVERLAPPED osWrite = {0};
    DWORD dwWritten;
    DWORD dwRes;
    BOOL fRes;
    // Create this write operation's OVERLAPPED structure's hEvent.
    osWrite.hEvent = CreateEvent(NULL, TRUE, FALSE, NULL);
    if (osWrite.hEvent == NULL)
    // error creating overlapped event handle
    return FALSE;
    // Issue write.
    if (!WriteFile(ghComm, lpBuf, dwToWrite, &dwWritten, &osWrite)) {
    if (GetLastError() != ERROR_IO_PENDING) {
    // WriteFile failed, but isn't delayed. Report error and abort.
    fRes = FALSE;
    else
    // Write is pending.
    dwRes = WaitForSingleObject(osWrite.hEvent, INFINITE);
    switch(dwRes)
    // OVERLAPPED structure's event has been signaled.
    case WAIT_OBJECT_0:
    if (!GetOverlappedResult(ghComm, &osWrite, &dwWritten, FALSE))
    fRes = FALSE;
    else
    // Write operation completed successfully.
    fRes = TRUE;
    break;
    default:
    // An error has occurred in WaitForSingleObject.
    // This usually indicates a problem with the
    // OVERLAPPED structure's event handle.
    fRes = FALSE;
    break;
    else
    // WriteFile completed immediately.
    fRes = TRUE;
    CloseHandle(osWrite.hEvent);
    return fRes;
    I get none of the specified errors, but game fails to start and it seems nothing gets written to parallel port. Any suggestions on how to proceed from here would be more than appreciated.
    Thank you, Joanna

  • Push button signal to parallel port to trigger a process

    I just need to connect a push button to the parallel port to set it as a trigger signal for a process.
    When push button is pressed, labview executes a process.
    Kindly help me how to do this, the wiring please
    Regards
    Grugh Mike
    Success is Everything !!
    Solved!
    Go to Solution.

    Data Lines to be used as inputsSome parallel ports can be configured to use the data lines as inputs. It depends a great deal on the way the manufacturer designed the parallel port. With some models the data lines can be read the same way we read the control lines, by driving them to high logic so they will take on the value of an external signal. However, most parallel ports require that you set the direction bit for input. This is bit 5 in the Control register (base+2). If the port is capable of it, setting the direction bit high has the effect of making the lines tri-state so it can be driven externally. Sometimes it is also necessary to toggle bit 6 high or low. However, it should be noted that some manufacturers actually lock these bits so that software cannot change them. An example is shown below in Figure 7.
    To test whether your data lines can be used for input, try the following:
    Set bit 5 of the control register high (at base address+2).
    With nothing connected to the port, write a couple of values to the data port, and read each back after you write it.
    If the reads DON'T match the writes, your port is probably bidirectional. Setting C5 disabled the data outputs and you're reading the open inputs of the data-port buffer. If the reads DO match the writes, your port isn't bidirectional. The data outputs are still enabled, you're reading back what you wrote, and you won't be able to read external signals. If it is possible to use your data lines for input, then you just need to set control register bit 5 high and read from the value of the data lines at the base address.

Maybe you are looking for