Permanent settings for touch screen

Hi All,
I am trying to configure the touch screen, for finger touch, for a Thinkpad X200 Tablet. Using xinput_calibrator, I got the correct Area values for having it calibrated, so with:
$ xsetwacom --set "Serial Wacom Tablet WACf008 touch" Area 43 81 952 937
I tested it and worked perfectly. To make the changes permanent, I created: /etc/X11/xorg.conf.d/99-calibration.conf
Section "InputClass"
Identifier "Touch Calibration"
MatchProduct "Serial Wacom Tablet WACf008 touch"
Option "Area" "43 81 952 937"
EndSection
But after rebooting, it doesn't work, it just takes the default uncalibrated values, as can be seen on:
$ xsetwacom --get "Serial Wacom Tablet WACf008 touch" "Area"
0 0 1024 1024
What I am doing wrong? I also tried setting MatchProduct "touch|Touch|TOUCH" just in case, but it doesn't work anyway.
Cheers,
Sergi

on the far left on the bottom of your screen you should see the windows symbol hit it. a widow will open showing various different funtions...Too your right of the screen you should see the word control panel hit it.another window will open look for the word screen Display and hit it.another window will open look for the word adjust brightness and hit it.another window will open and on the bottom of your screen you should see the brightness funtion. to adjust screen brightness.

Similar Messages

What are the new gestures for touch screens?

According to the help file with the Windows 10 Technical Preview for Enterprise build 9879 the same gestures that work on Windows 8.1 are supposed to work on Windows 10.
I cannot get swiping down from the top of the screen or the bottom of the screen to function in Modern apps. It worked fine on the same computer (Dell Venue 11 Pro Core-i5) in Windows 8.1. The touch screen works for other gestures such as swiping in from
the left or right, selecting, etc.
So to close an app, I can no longer swipe down from the top. I have to tap the X in the upper corner, or bring up the new switcher and close it from there. It's also difficult to bring up the additional menus in Modern apps. For instance, the Mail
app has menu options to move a message to a folder. I used to be able to swipe up from the bottom to bring up the menu items. Now I have to try to tap the ... in the lower right corner. On a smaller display, this is difficult.
I also noticed that ALL apps run on the desktop now. When launching a Modern app such as the included Mail app or the Facebook app from the store, they run on the desktop in a windowed mode with the taskbar visible. You can maximize them, but they are just
full screen windows on the desktop. They don't run in full screen mode like in Windows 8.
Windows 10 was supposed to add back features from Windows 7 to make it easier to navigate with a keyboard and mouse while retaining the existing Windows 8 functionality for touch screen devices like tablets. The current build is much harder to use on a tablet
than Windows 8.

The latest update was just bug fixes and improved stability, no new features. That is nearly always the case with series 40 phones like the 6300.
Nokia do not make the changelogs available publicly but often they do appear on unofficial sites. Searching google may provide you with more detailed info that cannot be posted here.

WebDynpro for ABAP applications for Touch Screen Clients?

Hi folks!
Has anybody in the WD4A community experiences in developing WebDynpro for ABAP applications for touch screen clients?
Any hint will be welcome.
Thanx in advance!
Regards,
Volker

Hi,
sorry, but Web Dynpro ABAP does not support touch screen clients. This would mean new Unified Rendering features which are, however, not scheduled.
Regards, Heidi

Need really big combobox for touch screen use-

I’m something of a Flash noob trying to convert an old
Director project to Flash/AS3 for touch screen and web deployment.
The project makes extensive use of comboboxes but the default style
is entirely too small for use on a touch screen. I found (and
mostly understand) the following tutorial for setting the font size
and various other text attributes but the UI elements: scroll bar,
thumb slider, scroll arrows, even the text containers don’t
scale with the text content. Do I really need to resize every
graphic component of the UI independently? Is there no way to just
take a combobox as is but make it bigger? Thanks.
Changing text attributes in an AS3 combobox:
http://www.rockabit.com/2008/04/15/combobox-text-formatting-in-as3/

I’m something of a Flash noob trying to convert an old
Director project to Flash/AS3 for touch screen and web deployment.
The project makes extensive use of comboboxes but the default style
is entirely too small for use on a touch screen. I found (and
mostly understand) the following tutorial for setting the font size
and various other text attributes but the UI elements: scroll bar,
thumb slider, scroll arrows, even the text containers don’t
scale with the text content. Do I really need to resize every
graphic component of the UI independently? Is there no way to just
take a combobox as is but make it bigger? Thanks.
Changing text attributes in an AS3 combobox:
http://www.rockabit.com/2008/04/15/combobox-text-formatting-in-as3/

Transaction IW32 for touch screen

Good evening,
I need release transaction IW32 for touch-screen(display for work by touch hand).
I need something as http://img221.imageshack.us/img221/5707/r3touchmn9.jpg
(i have done this in Graph Editor).
Create all features of IW32 in Web Dynpro from NULL is very difficult.
I think, that ITS server and webgui (transaction call from web) can help me.
But how i can edit standard style.css of webgui and can i, for example, create height button? (for example: width=200, height=200).
But maybe standard ABAP can help me?
It is very important for me.
Please, answer. <b><REMOVED BY MODERATOR></b>
Message was edited by:
Alvaro Tejada Galindo

You wrote
Utilizing the "Save as variant" option from the selection screen itself works out perfectly, but this variant cannot be transported.
But, give the variant a name beginning with "CUS&" and this variant will be transported. Variant beginning with "CUS&" or "SAP&" are so-called "system variant" and are transported automatically. You can then copy the transaction code and use this new variant in the new transaction.
Regards,
Raymond

Hello! The scrollbars in Windows iTunes are too narrow for touch screen. How to make it wider?

Hello! The scrollbars in Windows iTunes are too narrow for touch screen. How to make it wider?
Jan

Dear Experts,
I Developed Screen-exit For IW51 t.codeTypically the custom fields are displayed in the notification on a separate tab, or at the bottom of the u201CGeneralu201D or u201CMainu201D tab. These are configuration decisions that could be made in the build phase.
Sets of custom fields need to be added based on the notification type. The following table provides a list and details of the custom fields required. The table to be extended is the VIQMEL table (to be verified by developer).
Also to extend header fields on the notification you need to include them in the include CI_QMEL where OPEX M&I has already fields in.
All fields should go on the notification header. There are no custom fields on the task or activity level.
All fields should be reviewed for consistency with the M&I design, specifically, Thomas Brothers, Atlas Sheet, district code. See Dale Alano.
Please any Body Helped Coding For this, Already i Created Customfields , I design Subscreen also using Enhancement QQMA0001. Using Exit name EXIT_SAPMIWO0_008 USIN SUBSCREEN 0104 PLEASE ANY BODY help me Coding for this IW52
Regards,
Santosh Ballyapelli

Desing user friendly screen for touch screen at abap

Hi Experts,
I want to make design screen with screen programing for touch screen.
I'm trying some exam but it's not user friendly. For example : Heigth of Button is not greater 1.
How can I desing user friendly screen for touch screen at abap?
Best regards.

Hello,
as far as i know the button heigth in the Screen Painter can't be changed.
Maybe there is a way to display the dynpro bigger like 200% resolution.
Regards
Nico

Best settings for Green Screen Video with Canon Mark iii

HI
What are the ideal camera settings for Green screen video.
Iso?
aperature?
Depth of field settings (best to have the green screen a bit out of focus?)
Any other camera settings would be helpful.
Thanks
Rowby

Hi Rowby!
Thanks so much for writing in about green screen shooting with the EOS 5D Mark III camera. Green screen shooting can come down to some crucial elements and how well you handle the camera and the lighting.
Arguably the most important thing is to have excellent lighting on the screen. Without this, the keys used to replace the green screen will not be accurate. So hopefully you have a good set of lights you will be using to actually light the physical screen.
With regards to ISO, shoot as low as possible. We suggest that you stick in the ISO 200-400 range where possible. With good, high key, proper lighting on the screen this shouldn't be an issue.
Aperture should actually be in the higher end of the range, you would want to stick to apertures around f/8 and above. Again, with adequate lighting this shouldn't be out of reach. This is so the green screen is more in focus, versus having it out of focus, which would not yield successful results.
Use an appropriate lens to the subject, for example if you are doing wide shots- use only the focal length needed for the shoot and no wider. For head shots, close ups- use a lens that will get you close.
Following these suggestions should give you some pretty good results. Remember, if this is your first attempt don't be discouraged, green screen shooting can be difficult to accomplish.
We wish you the best of luck in your endeavor!
Did this answer your question? Please click the Accept as Solution button so that others may find the answer as well.

Desinging for touch screen

I have an educational program that I want to re-develop for
touch screens. It has been designed in Director MX.
Do I need a particular extra for the touch screen
functionality ?
I haven't designed any touch screen projects to date and am
still looking at the hardware.
If you have any experience of knowledge in this area I would
be very greateful to hear from you.
I am desiging it for disabled children so the kiosk will need
to be quite robust - any hints on kiosks?

Writing an app for a touch screen shouldn't require much
custom coding,
because the touch screens usually generate standard mouse
events. Have read
some of the previous post on the topic? I am sure there is
some good info in
many of them.
http://groups.google.com/group/macromedia.director.lingo/search?group=macromedia.director. lingo&q=touchscreen&qt_g=1

Hi - I have a new tool to create a tactile experience for touch screen users. Great for early educational apps. Any idea of how to get it exposure?

Hi - I created new tool to create a tactile experience for touch screen users. Created it for son with auditory processing problems and dyslexia. Great for early educational apps. or just for fun. Any idea of how to get it exposure? Thanks for you help!

Hire a marketer, perhaps? Put it up on Amazon? Only not here, that would be in direct violation of the term of use.

Having to push really hard for touch screen to respond.

I have owned my new iPod touch 5g for about 3 weeks now, and all of a sudden my touch screen has become non-responsive to touch unless I push down very hard on the screen. I have not droped it or anything to cause dameage to it.
Is this matter a defective iPod, or is it somethis that can be fixed?

Is the screen clean:
Try:
- Reset the iPod. Nothing will be lost
Reset iPod touch: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup
- Restore to factory settings/new iPod.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar

Flex for Touch Screen Interfaces

I am evaluating using Flex for the development of a couple of
touch screen kiosk projects. One major issue is the UI elements
like scroll bars. For both these projects, scroll bars are a design
necessity. (For better or for worse) Looking at the class
references it does not seem immediately clear that the scroll bars
can be modified in size. I do see that they can be skinned, but
there is no indication that I can go from the 16 px wide vertical
scroller to one say 48 px wide.
Any thoughts?

I believe you can. If you lookup the source code you can
change these constants, create your own libraries and use them. you
will have to learn FLEX beyond evaluating it to prove this out, but
it could be done. It's open source, but you need to check out the
type of license. You may be able to sell it as a proprietary
component.

Cannot Load Evtouch Module for Touch Screen

I cannot seem to load the evtouch module I need for the touch screen on my laptop. This is the error I get in the Xorg.0.log file in /var/log - any ideas? Is there a way I can recompile this for the cuurent xorg server version?
(II) LoadModule: "evtouch"
(II) Loading /usr/lib/xorg/modules/input//evtouch_drv.so
(II) Module evtouch: vendor="Kenan Esau"
compiled for 4.3.99.902, module version = 0.8.8
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 2.1
(EE) module ABI major version (2) doesn't match the server's version (4)
(II) UnloadModule: "evtouch"
(II) Unloading /usr/lib/xorg/modules/input//evtouch_drv.so
(EE) Failed to load module "evtouch" (module requirement mismatch, 0)

I have patched the evtouch source using Ubuntu diff file for this package (and other modifications to make it work with hal). It is loaded correctly now, but it doesn't work. When I touch the screen with the pen the mouse pointer goes to the upper left or down right corner. I made the calibration with ubuntu live and it works under ubuntu. Do you have the same problem with Arch?
EDIT: nevermind, I tried Ubuntu's binary and it worked, then I realized I forgot another debian patch. Adding this patch to the package I've made I got a working driver.
Last edited by gborzi (2009-04-25 19:37:30)

Best Sleep settings for Touch charging

So what's the best combination of settings in Sys.Pref.>Energy Saver so that my MBP won't sleep when charging my Touch? We charge the Touch like every day since it gets a lot of use, and I'm asking where to set the sliders under Settings for Power Adapter and Battery to insure it won't sleep while charging the Touch.

I would just buy a wall charger for the touch and leave your MBP alone. If you really only wanted to charge it from the MBP, just make sure it doesn't sleep when plugged into the power adapter.

Custom Sequence Settings for Split Screen

Hello all,
FCP 6. I am doing a split screen where I am combining two 720x480 videos side by side. I did the whole project by scaling down both videos to match whatever the sequence settings were. How can I create a custom canvas/ sequence size to avoid scaling down the frames and cutting on the image quality?
I created a custom sequence setting doubling the width to 1440 and keeping height at 480.
Can I copy and paste the clips from the old sequence without the scaled down quality to the new sequence? How can I do that?
If I open a new sequence is the new setting going to be in effect?
Any other suggestions on how to deal with custom size frame/ split screen?
Thank you!

Dear Jim,
Thank you for help! Does make sense. I did all like you suggested. After removing 'basic motion' and pasting into new sequence, the clips appeared big default size instead of small. I re-applied motion attribute like you said, but isn't it scaling down again since I am sizing from big to small (50%) again?
It looks good on the screen but I am not sure about actual resolution of the clip. In clip-item properties-format I read frame size but I am not sure if this info is about the source file or the clip.
I would like to get around this issue without scaling down (keeping the scale in motion tab at 100%).
The way I tried to deal with the scaling and res before I got your answer, was after I changed the 'global' settings for the custom 1440x480 sequence, and after creating a new sequence, I went to sequence settings again (from top menu) and set to custom (1440x480) (with just global settings the pasted clips looked like before). After copying and pasting with removed attributes-distort, all was in the original right/left order normal size and resolution.
The way I tried seems to meet my need (as pasting attributes-motion to all again would be complicated as the design of the project does not stick to the clearly left/right pattern but fluctuates back and forth at times and there is too many short clips).
The only problem I have now is with the RENDER.
After I rendered what I did to your suggested solution and mine (two sequences), the whole project shows in low res. I checked the render settings in Sequence-Render Control, and both resolution and frame rate are set to 100% so I dont know what I do wrong.
Any suggestions??
THANKS!!!

Permanent settings for touch screen

Similar Messages

Maybe you are looking for