Permanent wired connection for Time Machine how to set up

Just upgraded from 10.4 to 10.5.3 and I like to give TM a go but it seems to only work over wireless.
I see in the forums that some references are made as to making the first backup over Ethernet. However I do not seem to find how to set this up.
I would do my backups over my Ethernet network to my server with a external HD attached.
And I would like to do my backups only over Ethernet, is this possible?
Thanks

Ethernet needs to be an active network service in System Prefs/Network.
Before turning Time Machine on, with your MBP connected via Ethernet, Open System Prefs/Network and activate Built-In Ethernet, then move Built-In Ethernet to the top of the network interface list so it is the first choice. Then mount the destination drive on your MBP and in TM Prefs set that drive as the TM destination, make sure TM is set to NOT erase the destination drive, and turn TM on.
Your MBP should then back up to the desired mounted volume over Ethernet. Ethernet is faster than wi-fi, so your first backup with Time Machine will take less time.
Thereafter, if Time Machine is on it will attempt to back up every hour provided it can find and mount the destination volume. If that happens wirelessly it's no big deal because subsequent backups don't take all that long. If the destination volume is not available TM will simply wait until the volume can be seen again, and then continue.
One caveat: Since TM backs up a new copy of every changed file, very large files, such as a movie, Windows partition or Entourage mail database, can lengthen the time required for subsequent TM backups and use up space faster on the destination. Very large files like this I exclude from TM backup and back up separately.
Hope this helps.
Ken

Similar Messages

I need to configure a new hard disk as backup disk for time machine. The set up program is running and it says it will take 9 days to backup about 56 GB. Is it normal ?

I need to configure a new hard disk as backup disk for time machine.
The set up program is running since two hours and it says it will take 9 days to backup about 56 GB.
Is it normal ?

Roberto 17 wrote:
I started this morning at 12 and after 5 hours now the backup is about 6 GB up on 56 GB.
The new HD is a WD My Passport Edge 500 GB capacity
5 hours to do 6 GB of transfer is NOT normal, even for USB 2.0 so there's something wrong here. I'd say cancel it, wipe the drive and then test the integrity of the drive. Do some file transfers over to and see if it's behaving normally. It could be a bad USB cable, it could be a bad drive or bad enclosure. As it's new, I suspect you haven't really put it through its paces yet and it's important to do that first before commissioning it to serve as your "reliable backup."

Preferences are missing for Time Machine,how can I fix this?

Preferences are missing from Time Machine,how can I fix this?

Please don't SHOUT!
We're all users here and you'll get more help if you give us some coherrent information.
Firstly, do you have an external Hard Drive connected to use for your Time Machine backup?
Secondly "stacks" is not a programme; it's one method of presenting folder icons in the dock, and is accessed from the 'view options' choice which appears if you click on the folder. Right-clicking the folder will go straight to the options menu.

I recovered my back up via a wired connection. now Time Machine does not recognise older back ups wirelessly and wants to do a first back up

I recovered a back up from my time machine via a wired connection after getting the 'white screen of death'. Now Time Machine does not recognise any back ups on the time machine when connected wirelessly and wants to do a first back up of the whole machine. How do I get my mac to recognise these older back ups? It connects to the wifi network the time machine creates fine, with the same name and password.

I recommend the following.
1. Reset the TC to factory.
Universal Factory Reset.. any model TC or AE.
Unplug your TC/AE from power or turn off at the power point.
Hold in reset. and power the TC/AE back on.. all without releasing reset and keep holding in for about 10sec. (this is often difficult without a 2nd person or a 3rd arm).
Release it when the status light flashes rapidly. If it doesn’t flash rapidly you have missed it and try again.
Note..
Be Gentle! Feel the switch click on. It has a positive feel.. add no more pressure after that.
TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations of the router.
No files are deleted on the hard disk in a TC.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
2. Rename the TC to SMB standard.
That means short names.. 2-20 characters but less than 10 is excellent. eg TCGenx (use number for x that is actual generation of the TC)
No spaces.
Pure alphanumeric. No apostrophe.
3. Ensure IPv6 is set to link-local..
Do the same thing for ethernet if that is used.
4. Manually mount the TC disk in Finder.
Use Go in the top menu.. connect to server.
Type in
AFP://TCname.local (where TCname is your new short name for the TC and local is default domain .. it helps using the domain I found).
You will then find the computer either can or cannot find the network resource.. if it fails something else is wrong with the actual network and you will need to fix that.
It will request the password if it is found.. password is public by default unless you changed it.. type in the password and check to keep it in your keychain.
5. Delete current TM setup and redo it with the newly named TC.
See A4 here. http://pondini.org/TM/Troubleshooting.html
If your backups cannot be found, try B6 again, now that you actually know that the disk has been properly discovered.

Why no disks listed for time machine

I got my MACBOOK yesterday. When I ran time machine for the first time. it shows: A storage for time machine backups isnt set up. I clicked "set up time machine" , and click: choose backup disk. Howeve, none disks are listed, neither the internal HD, nor a portable disk connect to my MAC.
Don'tknow whether i missed anything, or just did something stupid. Can anybody help? Thanks a lot!!

I have the same problem with my EZQuest 120GB HD that I have been using for many years. I sent all folders/files to trash before trying Time Machine which failed to see this disk. In disk utility, it checks ok (repair permissions and repair disk) but it fails to recognize the disk for partition.
Any suggestions? The "Get info" results are pasted below.
David
Name : Indigita
Type : Disk
Partition Map Scheme : Unformatted
Disk Identifier : disk1
Media Name : Indigita Generic 1394 dev Media
Media Type : Generic
Connection Bus : FireWire
Connection ID : 13753799005283824
Device Tree : /PCI0/RP04@1C,3/FRWR@0/node@30dd01e005a5f0/sbp-2@c000/@0:0
Universal Unique Identifier : E2117719-B767-3D51-8FCC-5D78AAAFA5F2
Writable : Yes
Ejectable : Yes
Mac OS 9 Drivers Installed : No
Location : External
Total Capacity : 111.8 GB (120,034,123,776 Bytes)
Free Space : 89.9 GB (96,504,556,544 Bytes)
S.M.A.R.T. Status : Not Supported
Disk Number : 1
Partition Number : 0

How do I connect Airport Extreme and Time Capsule to my new iMac so that AE is used for network and TC only used for Time Machine backup?

I didn't realize that Time Capsule will only support the print function of a wireless multifunction printer. So I want to use Extreme for my network to have full use of my printer and use TC as the Time machine backup only. How to I make the connections?

Thanks for your response and this is getting complicated but I just purchased a new iMac as well as the Airport TC. I've had the Airport Extreme for a year or so. The Airport Extreme worked perfectly with my old iMac wirelessly and I had all functions of my printer with no problems. I was expecting the same with the TC. But the instruction that came with TC say to connect the printer to the TC via USB...which I did. And the print function worked perfectly but nothing else. In researching I discovered that when wired that way the TC only supports the print function...not scan or fax or anything else. I tried going wireless since my AE worked perfectly via wireless but I got no printer functions at all that way. But I'm wondering also if I tried that during a time I was having other issues...I had to delete and re-add my printer which solved some other problems. I may try that again...and see if I can get all print functions with just the TC connected
As far as connecting both your AirPort Extreme and Time Capsule on your network, we're not clear on exactly how you want to do this. Will the AirPort Extreme connect to your modem using an Ethernet cable and the Time Capsule connect to the AirPort Extreme using an Ethernet cable?.......or......do you want the Time Capsule to connect to the network using wireless?
Well... first of all I would like not to have to use the AE at all...I would prefer using just my TC for network, all print functions and Time Machine backup if that's possible. My printer will not accept Ethernet connections (Canon MX512).
After failing at getting this to work, I decided I would try to use my AE for net and print functions and just use my TC for Time Machine backup. I tried several different connection configurations with no success until finally I connected cable modem to my AE via Ethernet and went wireless with the AE and printer. but connected the AE to the TC via Ethernet and amazingly everything worked like a charm (for a while) and I was patting myself on the back for being so smart. But now I find that the connection only lasts for a short time. If I leave it for a while the TC goes invisible...or at least I see a message saying the Ethernet is unplugged...but it is not... and I lose internet connection even though I have a green light on my AE. So now I'm at a loss. I don't know why I keep losing network signal and why my system thinks the Ethernet is unplugged.
So... after all this...I figured I wasn't so smart after all and I must have things wired incorrectly.
So... it sounds like you are saying I should go back and try again to get my new TC to work as I want it to via wireless instead of connecting via USB...is that correct? Could you tell me exactly how I should wire my equipment from cable modem to AE and/or TC to achieve net capability, full functions of my printer and Time Machine backup...
Thanks...

I have a 1TB external hard drive (NTFS) that has all my files from my old PC, how do I create a partition on it for HFS without formatting it so that I can use it for Time Machine and the like?

I have a 1TB external hard drive (NTFS) that has all my files from my old PC, how do I create a partition on it for HFS without formatting it so that I can use it for Time Machine and the like?

There aren't any 3rd party apps or anything. I use PC's and Mac's at school and the only computer connected to a printer at my house is a PC so i need access to both

If I don't want to use my Seagate hard drive anymore for Time Machine...How do I go about this?

I want to use the external hard drive still, but not as my back up disk for Time Machine anymore. How do I make it so that my Macbook doesn't associate this specific external hard drive with TM when I plug it in?
Thanks

chenango232 wrote:
Missing a pretty big step here.... How does one install a new OS on an external drive? You can't install an OS without first booting into an OS. I don't have a disk to boot to, but have gotten as far as downloading the install software. Perhaps the answer you should be providing is that I need to create an install disk somehow?
Is not the current HDD in your MBP a boot drive? If so and you have Yosemite installed, you can boot into the recovery partition. From the 4 option menu you can use Disk Utility. If you have the NEW HDD connected to the MBP it will appear in Disk Utility. Click on that drive to format in Disk Utility>Erase. After formatting, go to the 'Reinstall OSX' option and install the OSX onto the external HDD. When finished swap the drives.
Ciao

HT201250 How do I find out what portable drive was the drive I used for Time Machine Backup?

Hi, I have 10.7.4 and need to figure out what drive I was using for Time Machine Backup. I have three drives and I have connected each of them to my macbook pro, but I get an error, "Time Machine Error, The backup disk is not available" when I hit the time machine icon on the top of the screen and the "backup delayed" prompt. If I try Back up Now I get message, "Time Machine could not complete the backup. Back up disk is not available." I am trying to figure out what the time machine back up would actually look like as a file on the drives but I don't see a folder/file name Time Machine. If I enter Time Machine I can see in the far right column, in purple, the last back up date (Sept. 12, 2012), but when I hit it nothing happens. In the Time Machine preference box the select disk has, in red and to the right, "Delayed" with an "i" within a circle, and the option indicates, "Next backup: when disk is connected."
I know I have a years worth of backups on one of the three drives, but I can't figure out how the heck to find them or how to determine what was the last drive I used for the backups within Time Machine. Help please.

Hi, I have 10.7.4 and need to figure out what drive I was using for Time Machine Backup. I have three drives and I have connected each of them to my macbook pro, but I get an error, "Time Machine Error, The backup disk is not available" when I hit the time machine icon on the top of the screen and the "backup delayed" prompt. If I try Back up Now I get message, "Time Machine could not complete the backup. Back up disk is not available." I am trying to figure out what the time machine back up would actually look like as a file on the drives but I don't see a folder/file name Time Machine. If I enter Time Machine I can see in the far right column, in purple, the last back up date (Sept. 12, 2012), but when I hit it nothing happens. In the Time Machine preference box the select disk has, in red and to the right, "Delayed" with an "i" within a circle, and the option indicates, "Next backup: when disk is connected."
I know I have a years worth of backups on one of the three drives, but I can't figure out how the heck to find them or how to determine what was the last drive I used for the backups within Time Machine. Help please.

HT201250 How can I revert to my internal drive for time machine backups after using an external drive?

Hi. I've been using an external drive for time machine back ups and decided to revert to my internal drive, but it isn't available in the time machine options. The only available option is to set up a time capsule, which I don't own.
Is it because not enough space is available on my internal drive (approx 50GB)?
Thanks!

50 Gb free on your internal drive is relly very low and of course not enought for a any kind of backup.
How big is your internal HD ? If you have left only 50 GB free it is probably 90% full. Let's imagine you have a 500 Gb. This means 450 Gb data and 50 Gb free. How can you backup 450 into 50 ?
Second point. The backup on your internal HD is a nonsense evenif it is big enough. If it stops working you will have no bakup.
Do you have an iMac or a portable ?
The portable automatic uses the internal HD if the external is not connected, but this is intended for a short time.
This could give you some more links to read about https://discussions.apple.com/message/20726927#20726927

New External Drive how do I set it for Time Machine?

I just bought a new 250g firewire to back up my hard drive - I formatted it and it's ok and all but I want to use it to back up my entire hard drive.
I thought I was supposed to make a Disk Image?? but browsing these forums it seems I was supposed to designate it for Time Machine? I didn't know that. Can I still do that? If so what do I do? and how do I do it?
also what is disk image? I thought that was supposed to be the back up feature -
and if anyone else knows and I'm allowed more questions - I really wanted to install Final Cut Studio Pro on the external drive because apparently it ***** up disk space like a --- -well you know ----- - but it says it has to be on my regular drive - does that mean I have to uninstall some programs? can I set other software to work off the external or am I going to have the same problem?
I'm so ******!! I bought the 120 g drive thinking it was enough to run programs off of and use the other for data storage - apparently not!
I'm about 10 gigs short right now and that doesn't even count leaving something for extra space.
I'm in a time crunch too - ok who isn't I know - but really - I'm on vaca now and was supposed to be working on my projects but instead am babysitting this freakin' computer and am really getting ******!!
so anyone that can jump in here and help please do so. I appreciate it very much am used to windows machines am new to mac in case that wasn't already blatantly apparent!

No disc image is required. Prepare the drive as follows:
Extended Hard Drive Preparation
1. Open Disk Utility in your Utilities folder. If you need to reformat your startup volume, then you must boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger or Leopard.)
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Click on the Options button, set the partition scheme to GUID (only required for Intel Macs) then click on the OK button. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Connect the drive to a Firewire port. Open Time Machine preferences and select the drive as the TM backup drive and turn on TM.
If you use the external drive for backups you should not use it for installing applications or storing other files. It should be used as a dedicated backup drive. If you need additional storage space get another external drive.
See Disk Image for discussion of what a disc image is.
Visit The XLab FAQs and read the FAQ on Backup and Restore.
Hopefully the next vacation you go on you will prepare for more thoroughly in advance. And, don't swear at the computer - it's a machine and only does what you tell it to do. If you need to swear at something look in the mirror!

Is using external HD connected to AP Extreme for Time Machine supported?

Hi,
I'm reconfiguring my network and looking at different back up options for the family's computers. I have a few external drives that I use to back up but I'd like to connect them to an Airport Extreme so I can centralize them.
After doing some research I can't seem to get a clear answer on this-
-Can I back up via Time Machine to external HDs that are connected to an Airport Extreme?
-How much of a hack is this/is this officially supported or am I better off going with a time machine?
Thanks.

If you don't have an AirPort Extreme base station (AEBS) yet you may want to save some money and simply share the drive from one of your Macs. The other Macs can use that as a destination for Time Machine backups.
I have a TB drive connected to an iMac which shares the drive. Time Machine on my iBook uses that drive as the destination for it's backup. The iBook is wirelessly connected to the network while the iMac is connected via Ethernet to the network.

I DONT HAVE STACKS AND I DONT HAVE ANYTHING FOR BACKUP ON TIME MACHINE HOW CAN I FIX THIS

I DONT HAVE STACK ON MY COMPUTER I THINK I ACCIDENTALLY ERASED IT AND EMPTIED THE TRASH AND I DONT NOW HOW TO GET IT BAC AND FOR TIME MACHINE IT DOESNT LET ME BACK UP ALL MY FILES HELPPPPP!!!!!

Please don't SHOUT!
We're all users here and you'll get more help if you give us some coherrent information.
Firstly, do you have an external Hard Drive connected to use for your Time Machine backup?
Secondly "stacks" is not a programme; it's one method of presenting folder icons in the dock, and is accessed from the 'view options' choice which appears if you click on the folder. Right-clicking the folder will go straight to the options menu.

I have a lion server set up to host storage for time machine backups. Is there a limit to how many different computers can back up to the single server to back up. I am only backing up the users folders . The backup drive is an external Drobo with 6 TB.

I have a lion server set up to host storage for time machine backups. Is there a limit to how many different computers can back up to the single server to back up. I am only backing up the users folders . The backup drive is an external Drobo with 6 TB. Right now it seems to back up my users all day long. I set their time machine interval to every 5 hours but it still runs all day long and is very slow. Server is on a new Mac Server mini.

AFAIK, there is no user limit.. it is simply a question of the network load. AFP is a fairly clean protocol.. but TM is not.. it does a lot of testing of the backup.. infact your setting of 5hour gap could well make it worse.
I would sort out the clients that are doing 100GB backups to a different backup location.. no matter how fast your network.. 100GB takes time to backup.. and over wireless forever.. it will never end.
I guess some of these clients are on wireless?? I would separate the TM of wireless to those that are wired. No more than 4 or 5 wireless clients to a target device. Otherwise you are saturating your network with backup data. And use 5ghz.. so close by.. it is much faster than 2.4ghz and you will get much better transfer rates.

I used a partitioned HDD for time machine, using a partition already containing other data files. I am now no longer able to view that partition in Finder. Disk Utility shows it in grey and "not mounted". Any suggestions of how to access the files?

I used a partitioned HDD for time machine, using a partition already containing other data files. I am now no longer able to view that partition in Finder. Disk Utility shows it in grey and "not mounted". Any suggestions of how to access the files? Does using time machine mean that that partition is no longer able to be used as it used to be?
HDD is a Toshiba 1TB, partitioned into two 500GB partitions.
OS X version 10.9.2

Yes, sharing a TM disk is a bad idea, and disks are cheap enough so that you don't need to.
Now
Have you tried to repair the disk yet

Permanent wired connection for Time Machine how to set up

Similar Messages

Maybe you are looking for