Phase 1 Negotiation Problems
Hi everybody,
I'm working on creating a tunnel between an ASA 5505 and a box running Check Point NG/AI. I've set up a couple of other Cisco to Check Point tunnels with this same Check Point peer without any problems. This time however, a SA is never created and I get the following when I debug ISAKMP on the ASA:
Dec 19 03:48:14 [IKEv1]: Group = x.x.7.225, IP = x.x.7.225, Received an un-encrypted PAYLOAD_MALFORMED notify message, dropping
Dec 19 03:48:14 [IKEv1]: Group = x.x.7.225, IP = x.x.7.225, Error, peer has indicated that something is wrong with our message. This could indicate a pre-shared key mismatch.
Dec 19 03:48:14 [IKEv1]: Group = x.x.7.225, IP = x.x.7.225, Information Exchange processing failed
The pre-shared key is not mismatched. Does anybody have any ideas as to what else I might check?
Thanks in advance,
Ryan
Ryan, you are correct in original post. The sa fails processing,I do not see anything indicating key matching or found peers. Have you guys try changing the keys for sake of trying different pre share key, what version code are you running.
[IKEv1 DEBUG]: Group = x.x.7.225, IP = x.x.7.225, Generating keys for Initiator...
[IKEv1 DEBUG]: Group = x.x.7.225, IP = x.x.7.225, constructing ID payload
[IKEv1 DEBUG]: Group = x.x.7.225, IP = x.x.7.225, constructing hash payload
[IKEv1 DEBUG]: Group = x.x.7.225, IP = x.x.7.225, Computing hash for ISAKMP
[IKEv1 DEBUG]: Group = x.x.7.225, IP = x.x.7.225, constructing dpd vid payload
[IKEv1]: IP = x.x.7.225, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + ID (5) + HASH (8) + VENDOR (13) + NONE (0) total length : 84
[IKEv1]: IP = x.x.7.225, IKE_DECODE RECEIVED Message (msgid=a3377722) with payloads : HDR + NOTIFY (11) + NONE (0) total length : 40
[IKEv1]: IP = x.x.7.225, IKE_DECODE RECEIVED Message (msgid=a3377722) with payloads : HDR + NOTIFY (11) + NONE (0) total length : 40
[IKEv1]: Group = x.x.7.225, IP = x.x.7.225, Received an un-encrypted PAYLOAD_MALFORMED notify message, dropping
Similar Messages
-
Custom tasklist variant - Phase Controller Internal Problem
Hello,
I am trying to work with a custom tasklist variant. For that I have created a ZSAP0 variant, and copied all tasks for H*** tasklist (cannot use the Urg* word, forbidden by the guidelines) and Maintenance Cycle. I did not put anything custom yet, I just want to have the custom variant working first.
I then create a maintenance project, assign a logical component and all that, as usual. Then, when creating the tasklist, I get the "Phase Controller Internal Problem" message. The task list is created but not active, and no service transaction is created.
I think maybe the link between the tasklist variant and the transaction type SDMN is not done, but I have no idea where this should be done, I cannot find anything about this in the IMG.
Would someone know that? Or have any other idea about why this is not working?
Thanks in advance.
ThomasHi,
Try this note
926087
If problem still persists, carry out activities as mentioned in the note 1129073.
Hope this solves your problem.
Feel free to revert back
-=-Ragu -
Xerox Phaser / IMac -Printer -Problem
Printing on my Xerox Phaser 8550 only works for ONE document. The second document always comes out as nonsense. Drivers are up to date, only solution is restarting the mac... Any ideas ?? Whenever I do this under Parallels there is no problem......
The latest Mountain Lion driver support begins with the Phaser 6130N. Tough break on the Phaser 6100.
Xerox has a page with links by operating system to PDF files containing all US Xerox printers compatible with the specific OS. There is a Mountain Lion link there.
If instead, you are wondering what supported non-Xerox printer to buy, look at the manufacturer specific driver updates on apple/support/downloads. Click the name of the driver update, rather than download it. You will see a link to a kb article that lists all currently supported printer models. For that manufacturer and other vendors. -
Phase import abap (problem in the import of the export)
Hello!:
We are doing the IMPORT of the EXPORT (for the CU&UC), and has appears the next error in the IMPORT ABAP PHASE:
(GSI) INFO: vname = "MSSQL "
(GSI) INFO: hostname = "IBA3SAP\MIG "
(GSI) INFO: sysname = "Windows NT"
(GSI) INFO: nodename = "IBA3SAP"
(GSI) INFO: release = "5.2"
(GSI) INFO: version = "3790 Service Pack 2"
(GSI) INFO: machine = "2x IA64 Level 31 (Mod 1 Step 5)"
(DB) INFO: ACCTIT created
(DB) INFO: ACCTIT~0 created
Interface access functions from dynamic library dbmssslib.dll loaded.
(IMP) INFO: ExeFastLoad failed with <2: BCP Commit failed>
(IMP) ERROR: ExeFastload: rc = 2
(DB) INFO: ACCTIT~1 created
(DB) INFO: disconnected from DB
M:\usr\sap\MIG\SYS\exe\uc\NTIA64\R3load.exe: job finished with 1 error(s)
M:\usr\sap\MIG\SYS\exe\uc\NTIA64\R3load.exe: END OF LOG: 20080409193447
Can you help me?
Thanks and regards,
Alfredo.IMPORT_MONITOR.LOG
ERROR: 2008-04-09 19:34:48 com.sap.inst.migmon.LoadTask run
Loading of 'ACCTIT' import package is interrupted with R3load error.
Process 'M:\usr\sap\MIG\SYS\exe\uc\NTIA64\R3load.exe -i ACCTIT.cmd -dbcodepage 4103 -l ACCTIT.log -loadprocedure fast' exited with return code 2.
For mode details see 'ACCTIT.log' file.
Standard error output:
sapparam: sapargv( argc, argv) has not been called.
sapparam(1c): No Profile used.
sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline
ERROR: 2008-04-09 19:53:03 com.sap.inst.migmon.LoadTask run
Loading of 'SAPAPPL1_34' import package is interrupted with R3load error.
Process 'M:\usr\sap\MIG\SYS\exe\uc\NTIA64\R3load.exe -i SAPAPPL1_34.cmd -dbcodepage 4103 -l SAPAPPL1_34.log -loadprocedure fast' exited with return code 2.
For mode details see 'SAPAPPL1_34.log' file.
Standard error output:
sapparam: sapargv( argc, argv) has not been called.
sapparam(1c): No Profile used.
sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline
ERROR: 2008-04-09 22:08:11 com.sap.inst.migmon.LoadTask run
Loading of 'SAPAPPL1_67' import package is interrupted with R3load error.
Process 'M:\usr\sap\MIG\SYS\exe\uc\NTIA64\R3load.exe -i SAPAPPL1_67.cmd -dbcodepage 4103 -l SAPAPPL1_67.log -loadprocedure fast' exited with return code 2.
For mode details see 'SAPAPPL1_67.log' file.
Standard error output:
sapparam: sapargv( argc, argv) has not been called.
sapparam(1c): No Profile used.
sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline
ERROR: 2008-04-10 08:22:35 com.sap.inst.migmon.LoadTask run
Loading of 'SAPAPPL0_17' import package is interrupted with R3load error.
Process 'M:\usr\sap\MIG\SYS\exe\uc\NTIA64\R3load.exe -i SAPAPPL0_17.cmd -dbcodepage 4103 -l SAPAPPL0_17.log -loadprocedure fast' exited with return code 2.
For mode details see 'SAPAPPL0_17.log' file.
Standard error output:
sapparam: sapargv( argc, argv) has not been called.
sapparam(1c): No Profile used.
sapparam: SAPSYSTEMNAME neither in Profile nor in Commandline -
Gigabitethernet negotiation problem with cisco 2960
Hi
I have 2 cisco 2960 switches. one is a WS-C2960-48TT-L Version 12.2(25r)SEE1 and the other WS-C2960-48TC-L Version 12.2(25r)FX.
When i build a trunk between the gigabit ethernet ports, WS-C2960-48TC-L end shows me half duplex with autonegotiation whereas it is hard coded on the WS-C2960-48TT-L.
Iam not able to set the speed and duplex for the port on the 2nd switch.
Is this a bug with the 2960 or a compatibility feature between the 2 2960's
NarayanHello Narayan,
Has the speed and dubplex settings on the 2960 been configured? In that case auto-negotiation frames are not sent and the switchport cannot determine the speed/duplex from it's link partner. It will automatically choose 1000 half-duplex.
Refer to the following document: http://www.cisco.com/warp/public/473/3.html
HTH
--Leon
* Please rate posts. -
Phase/nano3G authorisation problem!
Can anyone help?
I just purchased and downloaded Phase for my 3G nano but keep getting "not authroised" message when synching. Have confirmed I have latest versions of itunes 7.5 (19) and ipod s/w 1.0.2. Created Phase playlist in itunes then tried to synch - no joy. Disconnected ipod and reconnected/synch, again no joy.
Account info shows that I only have this one macbook authorised (no deauthroize all option presented and I haven't deuathorized previously ever, so that isn't the issue).
What gives? Why cant I play the game I already paid for?!Thanks Tariq,
Understood. Later what i undestood is that at Juniper end PFS Group-2 was enabled & cisco router end PFS Group-1 was enabled..Do you think in that case telnet will work & apps dont.
In same setup with another cisco edge router PFS Group-1 was cofigured but looks that override & applications worked perfect. At offshore it was same Juniper & configurations.
Yogesh -
OTA : Phase 1 certificate problem
Hello,
I'm trying to setup OTA Enrollment and succeeded in downloading the first Profile Service....but I'm unable to install and got the given message : "The server certificate for <my profile service URL> is invalid."
This is exactly the same server as the one I used to get the initial profile with self signed certificate.
The profile is not signed....How can I make it work ?
DavidI request a free SSL server certificate from 3rd party CA which is in the list of http://support.apple.com/kb/HT3580. And then set my profile server's domain to be the same as the common name of the server certificate. Then this issue can be resolved. However, There still is a warning before installing the last .mobileconfig which apple said there will be no user intervention required.
-
Problem with USRPs (phase offset)?
Hi I used this configuration (2 receivers (USRPs) and 1 transmitter (generator of sin wave)):
I did time and phase synchronisation .
the problem:
The received signals by the 2 USRPs are not superposed !??
how can I do to supperpose the signals received by the two USRPs??
please help me
Best regardsfirst of all, thanks for your answer.
unfortunally i didn't understand it in total.
do you mean, it is NOT possible to use any timezone setting, which is not based on a "standrad one" ?
as far as i know, there are countries using daylight saving time periods, which are not fixed to the "same start- and endtime for every year" (like israel for example).
i thought i can handle this "problem" using the posix string method to set the TZ environement.
so, is it not possible to use this linux feature (to use the export TZ=XST-1XDT..... command) combined with java ????
thanks for your help again.
regards
alex -
Problem with VPN client on Cisco 1801
Hi,
I have configured a new router for a customer.
All works fine but i have a strange issue with the VPN client.
When i start the VPN the client don't close the connection, ask for password, start to negotiate security policy the show the not connected status.
This is the log form the VPN client:
Cisco Systems VPN Client Version 5.0.07.0290
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1 14:37:59.133 04/08/13 Sev=Info/6 GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
2 14:38:01.321 04/08/13 Sev=Info/4 CM/0x63100002
Begin connection process
3 14:38:01.335 04/08/13 Sev=Info/4 CM/0x63100004
Establish secure connection
4 14:38:01.335 04/08/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "asgardvpn.dyndns.info"
5 14:38:02.380 04/08/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 79.52.36.120.
6 14:38:02.384 04/08/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
7 14:38:02.388 04/08/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 79.52.36.120
8 14:38:02.396 04/08/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
9 14:38:02.396 04/08/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
10 14:38:02.460 04/08/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
11 14:38:02.460 04/08/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, VID(Unity), VID(dpd), VID(?), VID(Xauth), VID(Nat-T), KE, ID, NON, HASH, NAT-D, NAT-D) from 79.52.36.120
12 14:38:02.506 04/08/13 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
13 14:38:02.460 04/08/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
14 14:38:02.460 04/08/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
15 14:38:02.460 04/08/13 Sev=Info/5 IKE/0x63000001
Peer supports DWR Code and DWR Text
16 14:38:02.460 04/08/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
17 14:38:02.460 04/08/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
18 14:38:02.465 04/08/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
19 14:38:02.465 04/08/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 79.52.36.120
20 14:38:02.465 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
21 14:38:02.465 04/08/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xCEFD, Remote Port = 0x1194
22 14:38:02.465 04/08/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
23 14:38:02.465 04/08/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
24 14:38:02.502 04/08/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 79.52.36.120
25 14:38:02.502 04/08/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 79.52.36.120
26 14:38:02.502 04/08/13 Sev=Info/4 CM/0x63100015
Launch xAuth application
27 14:38:07.623 04/08/13 Sev=Info/4 CM/0x63100017
xAuth application returned
28 14:38:07.623 04/08/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 79.52.36.120
29 14:38:12.656 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
30 14:38:22.808 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
31 14:38:32.949 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
32 14:38:43.089 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
33 14:38:53.230 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
34 14:39:03.371 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
35 14:39:13.514 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
36 14:39:23.652 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
37 14:39:33.807 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
38 14:39:43.948 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
39 14:39:54.088 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
40 14:40:04.233 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
41 14:40:14.384 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
42 14:40:24.510 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
43 14:40:34.666 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
44 14:40:44.807 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
45 14:40:54.947 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
46 14:41:05.090 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
47 14:41:15.230 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
48 14:41:25.370 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
49 14:41:35.524 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
50 14:41:45.665 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
51 14:41:55.805 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
52 14:42:05.951 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
53 14:42:16.089 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
54 14:42:26.228 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
55 14:42:36.383 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
56 14:42:46.523 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
57 14:42:56.664 04/08/13 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
58 14:43:02.748 04/08/13 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
59 14:43:02.748 04/08/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DWR) to 79.52.36.120
60 14:43:03.248 04/08/13 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=2B1FFC3754E3B290 R_Cookie=73D546631A33B5D6) reason = DEL_REASON_CANNOT_AUTH
61 14:43:03.248 04/08/13 Sev=Info/4 CM/0x63100014
Unable to establish Phase 1 SA with server "asgardvpn.dyndns.info" because of "DEL_REASON_CANNOT_AUTH"
62 14:43:03.248 04/08/13 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
63 14:43:03.262 04/08/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
64 14:43:03.262 04/08/13 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
65 14:43:03.265 04/08/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
66 14:43:03.265 04/08/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
67 14:43:03.265 04/08/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
68 14:43:03.265 04/08/13 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
And this is the conf from the 1801:
hostname xxx
boot-start-marker
boot-end-marker
enable secret 5 xxx
aaa new-model
aaa authentication login xauthlist local
aaa authorization network groupauthor local
aaa session-id common
dot11 syslog
no ip cef
no ip dhcp use vrf connected
ip dhcp excluded-address 10.0.1.1 10.0.1.10
ip dhcp excluded-address 10.0.1.60 10.0.1.200
ip dhcp excluded-address 10.0.1.225
ip dhcp excluded-address 10.0.1.250
ip dhcp pool LAN
network 10.0.1.0 255.255.255.0
default-router 10.0.1.10
dns-server 10.0.1.200 8.8.8.8
domain-name xxx
lease infinite
ip name-server 10.0.1.200
ip name-server 8.8.8.8
ip name-server 8.8.4.4
ip inspect log drop-pkt
ip inspect name Firewall cuseeme
ip inspect name Firewall dns
ip inspect name Firewall ftp
ip inspect name Firewall h323
ip inspect name Firewall icmp
ip inspect name Firewall imap
ip inspect name Firewall pop3
ip inspect name Firewall rcmd
ip inspect name Firewall realaudio
ip inspect name Firewall rtsp
ip inspect name Firewall esmtp
ip inspect name Firewall sqlnet
ip inspect name Firewall streamworks
ip inspect name Firewall tftp
ip inspect name Firewall vdolive
ip inspect name Firewall udp
ip inspect name Firewall tcp
ip inspect name Firewall https
ip inspect name Firewall http
multilink bundle-name authenticated
username xxx password 0 xxxx
crypto isakmp policy 3
encr 3des
authentication pre-share
group 2
crypto isakmp client configuration group xxx
key xxx
dns 10.0.1.200
wins 10.0.1.200
domain xxx
pool ippool
acl 101
crypto ipsec transform-set myset esp-3des esp-sha-hmac
crypto ipsec transform-set xauthtransform esp-des esp-md5-hmac
crypto dynamic-map dynmap 10
set transform-set myset
crypto map clientmap client authentication list userauthen
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
archive
log config
hidekeys
interface ATM0
no ip address
no atm ilmi-keepalive
pvc 8/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode adsl2+
hold-queue 224 in
interface FastEthernet0
interface FastEthernet1
interface FastEthernet2
interface FastEthernet3
interface Vlan1
ip address 10.0.1.10 255.255.255.0
ip nat inside
ip virtual-reassembly
interface Dialer0
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp pap sent-username aliceadsl password 0 aliceadsl
crypto map clientmap
ip local pool ippool 10.16.20.1 10.16.20.200
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
ip route 0.0.0.0 0.0.0.0 10.0.1.2
ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer0 overload
ip nat inside source static udp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 1056 interface Dialer0 1056
ip nat inside source static tcp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source static udp 10.0.1.60 3111 interface Dialer0 3111
ip nat inside source list 101 interface Dialer0 overload
access-list 101 remark *** ACL nonat ***
access-list 101 deny ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
access-list 101 permit ip 10.0.1.0 0.0.0.255 any
access-list 150 remark *** ACL split tunnel ***
access-list 150 permit ip 10.0.1.0 0.0.0.255 10.16.20.0 0.0.0.255
control-plane
line con 0
no modem enable
line aux 0
line vty 0 4
password xxx
scheduler max-task-time 5000
end
Anyone can help me ?
Sometimes the vpn can be vreated using the iPhone or iPad vpn client...I am having a simuliar issue with my ASA 5505 that I have set up. I am trying to VPN into the Office. I have no problem accessing the Office network when I am on the internet without the ASA 5505. After I installed the 5505, and there is internet access, I try to connect to the Office network without success. The VPN connects with the following error.
3 Dec 31 2007 05:30:00 305006 xxx.xx.114.97
regular translation creation failed for protocol 50 src inside:192.168.1.9 dst outside:xxx.xx.114.97
HELP? -
Remote Access VPN Problem with ASA 5505
After about ~1 year of having the Cisco VPN Client connecting to a ASA 5505 without any problems, suddenly one day it stops working. The client is able to get a connection to the ASA and browse the local network for only about 30 seconds after connection. After that, no access is available to the network behind the ASA. I tried everything that I can think of to try and troubleshoot the problem, but at this point I am just banging my head against a wall. Does anyone know what could cause this?
Here is the running cfg of the ASA
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password xxxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxx encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http **.**.***.*** 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
And here is the logs from the Cisco VPN Client when it browses, then fails to browse the network behind the ASA:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600026
Attempting to find a Certificate using Serial Hash.
2 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600027
Found a Certificate using Serial Hash.
3 09:44:55.693 10/01/13 Sev=Info/6 GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
4 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100002
Begin connection process
5 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100004
Establish secure connection
6 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
7 09:45:02.802 10/01/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
8 09:45:02.818 10/01/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
9 09:45:02.865 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
10 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
11 09:45:02.896 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
12 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
13 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
14 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
15 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
16 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
17 09:45:02.927 10/01/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
18 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
19 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 10/01/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end is NOT behind a NAT device
21 09:45:02.927 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 09:45:02.943 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 09:45:02.943 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 09:45:02.943 10/01/13 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 09:45:03.037 10/01/13 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
26 09:45:03.037 10/01/13 Sev=Info/4 CM/0x63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
28 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
29 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
30 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
31 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
32 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
33 09:45:03.083 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
34 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
35 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
36 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
37 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
38 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
39 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
40 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
41 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
42 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
43 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
45 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
46 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0x00002710
47 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
48 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
49 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
50 09:45:03.146 10/01/13 Sev=Info/4 CM/0x63100019
Mode Config data received
51 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
52 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
53 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
54 09:45:03.177 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
55 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
56 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 1 seconds, setting expiry to 86399 seconds from now
57 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
58 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
59 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
60 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to **.**.***.***
61 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=967A3C93 OUTBOUND SPI = 0xAAAF4C1C INBOUND SPI = 0x3EBEBFC5)
62 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xAAAF4C1C
63 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 10/01/13 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
66 09:45:03.896 10/01/13 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
67 09:45:03.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 10/01/13 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
69 09:45:07.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**.**.***.*** 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 10/01/13 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
71 09:45:07.912 10/01/13 Sev=Info/4 CM/0x6310001A
One secure connection established
72 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 96.11.251.149. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 10/01/13 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
75 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
76 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
77 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x1c4cafaa into key list
78 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
79 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xc5bfbe3e into key list
80 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
81 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
83 09:45:13.459 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
84 09:45:13.459 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205276
85 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
86 09:45:13.474 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
87 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205276, seq# expected = 107205276
88 09:45:15.959 10/01/13 Sev=Info/4 IPSEC/0x63700019
Activate outbound key with SPI=0x1c4cafaa for inbound key with SPI=0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
90 09:46:00.947 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205277
91 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
92 09:46:01.529 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
93 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205277, seq# expected = 107205277
94 09:46:11.952 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
95 09:46:11.952 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205278
96 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
97 09:46:11.979 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
98 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205278, seq# expected = 107205278
Any help would be appreciated, thanks!I made the change that you requested by moving the VPN pool to the 192.168.3.0 network. Unfortunately, now traffic isn't flowing to the inside network at all. I was going to make a specific route as you suggested, but as far as I can see the routes are already being created correctly on the VPN client's end.
Here is the route print off of the computer behind the (test) client:
===========================================================================
Interface List
21...00 05 9a 3c 78 00 ......Cisco Systems VPN Adapter for 64-bit Windows
10...00 15 5d 01 02 01 ......Microsoft Hyper-V Network Adapter
15...00 15 5d 01 02 02 ......Microsoft Hyper-V Network Adapter #2
1...........................Software Loopback Interface 1
13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
23...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
69.61.228.178 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 On-link 96.11.251.149 261
96.11.251.149 255.255.255.255 On-link 96.11.251.149 261
96.11.251.255 255.255.255.255 On-link 96.11.251.149 261
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.1.0 255.255.255.0 On-link 192.168.1.3 261
192.168.1.3 255.255.255.255 On-link 192.168.1.3 261
192.168.1.255 255.255.255.255 On-link 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.3.1 192.168.3.70 100
192.168.3.0 255.255.255.0 On-link 192.168.3.70 261
192.168.3.70 255.255.255.255 On-link 192.168.3.70 261
192.168.3.255 255.255.255.255 On-link 192.168.3.70 261
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.1.3 261
224.0.0.0 240.0.0.0 On-link 96.11.251.149 261
224.0.0.0 240.0.0.0 On-link 192.168.3.70 261
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.1.3 261
255.255.255.255 255.255.255.255 On-link 96.11.251.149 261
255.255.255.255 255.255.255.255 On-link 192.168.3.70 261
===========================================================================
Persistent Routes:
Network Address Netmask Gateway Address Metric
0.0.0.0 0.0.0.0 96.11.251.1 Default
===========================================================================
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
14 1020 ::/0 2002:c058:6301::c058:6301
14 1020 ::/0 2002:c058:6301::1
1 306 ::1/128 On-link
14 1005 2002::/16 On-link
14 261 2002:600b:fb95::600b:fb95/128
On-link
15 261 fe80::/64 On-link
10 261 fe80::/64 On-link
21 261 fe80::/64 On-link
10 261 fe80::64ae:bae7:3dc0:c8c4/128
On-link
21 261 fe80::e9f7:e24:3147:bd/128
On-link
15 261 fe80::f116:2dfd:1771:125a/128
On-link
1 306 ff00::/8 On-link
15 261 ff00::/8 On-link
10 261 ff00::/8 On-link
21 261 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
And here is the updated running config in case you need it:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
access-list outside_specific_blocks extended deny ip host 121.168.66.35 any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
ip local pool VPN_Split_Pool 192.168.3.70-192.168.3.80 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh 96.11.251.186 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Split_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Split_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Split_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:9e8466cd318c0bd35bc660fa65ba7a03
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Thanks again for your help,
Matthew -
Problem with Remote Access VPN on ASA 5505
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
Begin connection process
3 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100004
Establish secure connection
4 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
5 15:09:21.287 12/11/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
6 15:09:21.287 12/11/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
7 15:09:21.303 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
8 15:09:21.365 12/11/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
9 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
10 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
11 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
12 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
13 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
14 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
15 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
16 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
17 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
18 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
19 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xFBCE, Remote Port = 0x1194
20 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
21 15:09:21.334 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 15:09:21.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 15:09:21.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 15:09:21.365 12/11/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
26 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
27 15:09:27.319 12/11/12 Sev=Info/4 CM/0x63100017
xAuth application returned
28 15:09:27.319 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
29 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
30 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
31 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
32 15:09:27.365 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
33 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
34 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
35 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
36 15:09:27.397 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
37 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
38 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
39 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
40 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
41 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
42 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO
43 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
44 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.2(5) built by builders on Fri 20-May-11 16:00
45 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
46 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
47 15:09:27.397 12/11/12 Sev=Info/4 CM/0x63100019
Mode Config data received
48 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
49 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
50 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
51 15:09:27.444 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
52 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
53 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 6 seconds, setting expiry to 86394 seconds from now
54 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
55 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from **.**.***.***
56 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to **.**.***.***
57 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000049
Discarding IPsec SA negotiation, MsgID=CE99A8A8
58 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
59 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
60 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000058
Received an ISAKMP message for a non-active SA, I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924
61 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(Dropped) from **.**.***.***
62 15:09:27.490 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
63 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
64 15:09:30.475 12/11/12 Sev=Info/4 CM/0x63100012
Phase 1 SA deleted before first Phase 2 SA is up cause by "DEL_REASON_IKE_NEG_FAILED". 0 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
65 15:09:30.475 12/11/12 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
66 15:09:30.475 12/11/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
67 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
68 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
69 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
70 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
71 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
The running configuration is as follows (there is a site-to-site VPN set up as well to another ASA 5505, but that is working flawlessly):
: Saved
ASA Version 8.2(5)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
boot system disk0:/asa825-k8.bin
ftp mode passive
access-list outside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit NCHCO 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (outside) 0 access-list outside_nat0_outbound
route outside 0.0.0.0 0.0.0.0 74.219.208.49 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec transform-set l2tp-transform mode transport
crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_3DES_MD5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp ipsec-over-tcp port 10000
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHVPN internal
group-policy NCHVPN attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value NCHCO
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password QhZZtJfwbnowceB7 encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
pre-shared-key *****
tunnel-group NCHVPN type remote-access
tunnel-group NCHVPN general-attributes
address-pool VPN_Pool
default-group-policy NCHVPN
tunnel-group NCHVPN ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:15852745977ff159ba808c4a4feb61fa
: end
asdm image disk0:/asdm-645.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Anyone have any idea why this is happening?
Thanks!Thanks again for your reply, and sorry about the late response, havent gotten back to this issue until just now. I applied the above command as you specified, and unfortunately, it did not resolve the problem. Below are the logs from the VPN Client for the connection + attempted browsing of a network share that is behind the ASA, and the new running configuration.
VPN Client Log:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
331 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100002
Begin connection process
332 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100004
Establish secure connection
333 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "69.61.228.178"
334 13:11:41.362 12/17/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 69.61.228.178.
335 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
336 13:11:41.424 12/17/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
337 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 69.61.228.178
338 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
339 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 69.61.228.178
340 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
341 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
342 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
343 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
344 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
345 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
346 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 69.61.228.178
347 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
348 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xD271, Remote Port = 0x1194
349 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
350 13:11:41.393 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
351 13:11:41.424 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
352 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
353 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
354 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100017
xAuth application returned
355 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
356 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
357 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
358 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
359 13:11:41.456 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
360 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
361 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
362 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
363 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
364 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
365 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
366 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
367 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
368 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
369 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
370 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
371 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
372 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
373 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
374 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
375 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
376 13:11:41.502 12/17/12 Sev=Info/4 CM/0x63100019
Mode Config data received
377 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = 69.61.228.178, Remote IP = 0.0.0.0
378 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 69.61.228.178
379 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
380 13:11:41.534 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
381 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
382 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 0 seconds, setting expiry to 86400 seconds from now
383 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
384 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
385 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
386 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to 69.61.228.178
387 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=C4F5B5A6 OUTBOUND SPI = 0xD2DBADEA INBOUND SPI = 0x14762837)
388 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xD2DBADEA
389 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x14762837
390 13:11:41.549 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
391 13:11:41.877 12/17/12 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
392 13:11:43.455 12/17/12 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
393 13:11:43.455 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 266
394 13:11:47.517 12/17/12 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
395 13:11:47.517 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
69.61.228.178 255.255.255.255 192.168.1.1 192.168.1.162 100
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.2 255.255.255.255 192.168.1.162 192.168.1.162 100
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 266
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 266
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 266
396 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
397 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310001A
One secure connection established
398 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.1.162. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
399 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
400 13:11:47.517 12/17/12 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
401 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
402 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
403 13:11:47.517 12/17/12 Sev=Info/6 IPSEC/0x6370002C
Sent 109 packets, 0 were fragmented.
404 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
405 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
406 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xeaaddbd2 into key list
407 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
408 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x37287614 into key list
409 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
410 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 192.168.1.162. SG: 69.61.228.178
411 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
412 13:11:52.688 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
413 13:11:52.688 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476009
414 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
415 13:11:52.704 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
416 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476009, seq# expected = 2722476009
417 13:12:03.187 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
418 13:12:03.187 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476010
419 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
420 13:12:03.202 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
421 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476010, seq# expected = 2722476010
422 13:12:14.185 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
423 13:12:14.185 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476011
424 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
425 13:12:14.201 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
426 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476011, seq# expected = 2722476011
427 13:12:24.762 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
428 13:12:24.762 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476012
429 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
430 13:12:24.778 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
431 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476012, seq# expected = 2722476012
New running configuration:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:b6ce58676b6aaeba48caacbeefea53a5
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
I'm at a loss myself as to why this isn't working, and i'm sure that you are running out of solutions yourself. Any other ideas? I really need to get this working.
Thanks so much!
Matthew -
Cisco vpn connect problem with 3g dongle
Hi,
I am trying to connect cisco vpn but every time i am getting following error while trying to connect from huawei 3g usb dongle in win8. for win7 it works fine with no issue. Also the problem is only form datacard, form lan and wireless interaface i can easily connect to vpn without any issue. Any help/idea/suggestion highly appreciated?
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
25 08:06:46.846 12/25/13 Sev=Info/4 CM/0x63100002
Begin connection process
26 08:06:46.848 12/25/13 Sev=Info/4 CM/0x63100004
Establish secure connection
27 08:06:46.848 12/25/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "116.68.208.113"
28 08:06:46.849 12/25/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 116.68.208.113.
29 08:06:46.855 12/25/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
30 08:06:46.858 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 116.68.208.113
31 08:06:47.145 12/25/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
32 08:06:47.145 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
33 08:06:52.144 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
34 08:06:52.144 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
35 08:06:57.144 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
36 08:06:57.144 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
37 08:07:02.145 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
38 08:07:02.145 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
39 08:07:07.145 12/25/13 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=97205EA6A12866F0 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
40 08:07:07.645 12/25/13 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=97205EA6A12866F0 R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
41 08:07:07.645 12/25/13 Sev=Info/4 CM/0x63100014
Unable to establish Phase 1 SA with server "116.68.208.113" because of "DEL_REASON_PEER_NOT_RESPONDING"
42 08:07:07.645 12/25/13 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
43 08:07:07.645 12/25/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
44 08:07:07.645 12/25/13 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
45 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
46 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
47 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
48 08:07:08.146 12/25/13 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
49 08:19:59.202 12/25/13 Sev=Info/4 CM/0x63100002
Begin connection process
50 08:19:59.202 12/25/13 Sev=Info/4 CM/0x63100004
Establish secure connection
51 08:19:59.202 12/25/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "116.68.208.113"
52 08:19:59.202 12/25/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 116.68.208.113.
53 08:19:59.202 12/25/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
54 08:19:59.218 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 116.68.208.113
55 08:19:59.656 12/25/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
56 08:19:59.656 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
57 08:20:04.656 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
58 08:20:04.656 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
59 08:20:09.656 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
60 08:20:09.656 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
61 08:20:14.656 12/25/13 Sev=Info/4 IKE/0x63000021
Retransmitting last packet!
62 08:20:14.656 12/25/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (Retransmission) to 116.68.208.113
63 08:20:19.656 12/25/13 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=46B8917FD54C64AC R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
64 08:20:20.156 12/25/13 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=46B8917FD54C64AC R_Cookie=0000000000000000) reason = DEL_REASON_PEER_NOT_RESPONDING
65 08:20:20.156 12/25/13 Sev=Info/4 CM/0x63100014
Unable to establish Phase 1 SA with server "116.68.208.113" because of "DEL_REASON_PEER_NOT_RESPONDING"
66 08:20:20.156 12/25/13 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
67 08:20:20.156 12/25/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
68 08:20:20.156 12/25/13 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
69 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
70 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
71 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
72 08:20:20.156 12/25/13 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stoppedHi Karsten,
Thank you for the reply !!! & best wishes for the new year 2014.
The problem is like this, if i select datacard connection type to NDIS it works but it doesnt work when i select RAS(modem) connection type for 3G datacard it doesnt. (NDIS and RAS(Modem) connection types are the 2 modes currently supporetd by the datacard.). Is there any case the users are experiencing from the similar problem? and what they have done to solve the issues? And thank you for the workaroung, i have checked the shrew-soft with win7 and it was working fine but not on win8, i will check shrew-soft on win8 very soon. Also we can move to the anyconnect solution but just want to know if this can solve our problem or not? whether there will be any issues with anyconnect solution for win 8 or not? can you please confim.
Thank you -
Hello,
I experiance problems with QuickVPN client (version 1.4.1.2). I'm trying to connect to router SA520 with 1.1.65 firmware,
vpn tunell is established, but client says "The remote gateway is not responding. Do you want to wait?"
in case i click no, it drops vpn tunell
QuickVPN client log looks like this:
2010/08/18 12:13:27 [STATUS]OS Version: Windows 7
2010/08/18 12:13:27 [STATUS]Windows Firewall Domain Profile Settings: ON
2010/08/18 12:13:27 [STATUS]Windows Firewall Private Profile Settings: ON
2010/08/18 12:13:27 [STATUS]Windows Firewall Private Profile Settings: ON
2010/08/18 12:13:27 [STATUS]One network interface detected with IP address 192.168.1.100
2010/08/18 12:13:27 [STATUS]Connecting...
2010/08/18 12:13:27 [DEBUG]Input VPN Server Address = vpn.in-volv.lv
2010/08/18 12:13:28 [STATUS]Connecting to remote gateway with IP address: 78.28.223.10
2010/08/18 12:13:28 [WARNING]Server's certificate doesn't exist on your local computer.
2010/08/18 12:13:30 [STATUS]Remote gateway was reached by https ...
2010/08/18 12:13:30 [STATUS]Provisioning...
2010/08/18 12:13:39 [STATUS]Success to connect.
2010/08/18 12:13:39 [STATUS]Tunnel is configured. Ping test is about to start.
2010/08/18 12:13:39 [STATUS]Verifying Network...
2010/08/18 12:13:44 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:47 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:50 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:53 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:13:56 [WARNING]Failed to ping remote VPN Router!
2010/08/18 12:14:08 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2010/08/18 12:14:12 [STATUS]Disconnecting...
2010/08/18 12:14:15 [STATUS]Success to disconnect.
Server logs look like this:
2010-08-18 12:28:49: INFO: Adding IPSec configuration with identifier "arvils"
2010-08-18 12:29:02: INFO: Configuration found for 83.243.93.200[500].
2010-08-18 12:29:02: INFO: Received request for new phase 1 negotiation: 78.28.223.10[500]<=>83.243.93.200[500]
2010-08-18 12:29:02: INFO: Beginning Identity Protection mode.
2010-08-18 12:29:02: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 12:29:02: INFO: Received Vendor ID: RFC 3947
2010-08-18 12:29:02: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: Received unknown Vendor ID
2010-08-18 12:29:02: INFO: For 83.243.93.200[500], Selected NAT-T version: RFC 3947
2010-08-18 12:29:02: INFO: NAT-D payload matches for 78.28.223.10[500]
2010-08-18 12:29:02: INFO: NAT-D payload does not match for 83.243.93.200[500]
2010-08-18 12:29:02: INFO: NAT detected: PEER
2010-08-18 12:29:02: INFO: Floating ports for NAT-T with peer 83.243.93.200[4500]
2010-08-18 12:29:02: INFO: ISAKMP-SA established for 78.28.223.10[4500]-83.243.93.200[4500] with spi:e2cd855a75fc0887:6dc3b2e025152444
2010-08-18 12:29:02: INFO: Sending Informational Exchange: notify payload[INITIAL-CONTACT]
2010-08-18 12:29:02: INFO: Responding to new phase 2 negotiation: 78.28.223.10[0]<=>83.243.93.200[0]
2010-08-18 12:29:02: INFO: Using IPsec SA configuration: 192.168.75.0/24<->192.168.1.100/32
2010-08-18 12:29:02: INFO: Adjusting peer's encmode 3(3)->Tunnel(1)
2010-08-18 12:29:02: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 83.243.93.200->78.28.223.10 with spi=47693803(0x2d7bfeb)
2010-08-18 12:29:02: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 78.28.223.10->83.243.93.200 with spi=1079189482(0x40531fea)
2010-08-18 12:35:57: INFO: an undead schedule has been deleted: 'pk_recvupdate'.
2010-08-18 12:35:57: INFO: Purged IPsec-SA with proto_id=ESP and spi=1079189482(0x40531fea).
2010-08-18 12:40:46: INFO: Configuration found for 83.243.93.200[500].
2010-08-18 12:40:46: INFO: Received request for new phase 1 negotiation: 78.28.223.10[500]<=>83.243.93.200[500]
2010-08-18 12:40:46: INFO: Beginning Identity Protection mode.
2010-08-18 12:40:46: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 12:40:46: INFO: Received Vendor ID: RFC 3947
2010-08-18 12:40:46: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 12:40:46: INFO: Received unknown Vendor ID
2010-08-18 12:40:46: INFO: Received unknown Vendor ID
2010-08-18 12:40:46: INFO: Received unknown Vendor ID
2010-08-18 12:40:46: INFO: For 83.243.93.200[500], Selected NAT-T version: RFC 3947
2010-08-18 12:40:46: INFO: NAT-D payload matches for 78.28.223.10[500]
2010-08-18 12:40:46: INFO: NAT-D payload does not match for 83.243.93.200[500]
2010-08-18 12:40:46: INFO: NAT detected: PEER
2010-08-18 12:40:46: INFO: Floating ports for NAT-T with peer 83.243.93.200[4500]
2010-08-18 12:40:46: INFO: ISAKMP-SA established for 78.28.223.10[4500]-83.243.93.200[4500] with spi:28447d39874689f9:a2b7da19d8d86413
2010-08-18 12:40:46: INFO: Responding to new phase 2 negotiation: 78.28.223.10[0]<=>83.243.93.200[0]
2010-08-18 12:40:46: INFO: Using IPsec SA configuration: 192.168.75.0/24<->192.168.1.100/32
2010-08-18 12:40:46: INFO: Adjusting peer's encmode 3(3)->Tunnel(1)
2010-08-18 12:40:47: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 83.243.93.200->78.28.223.10 with spi=259246202(0xf73c87a)
2010-08-18 12:40:47: INFO: IPsec-SA established[UDP encap 4500->4500]: ESP/Tunnel 78.28.223.10->83.243.93.200 with spi=3642234214(0xd9181566)
2010-08-18 12:43:27: INFO: IPsec-SA expired: ESP/Tunnel 83.243.93.200->78.28.223.10 with spi=33356156(0x1fcf97c)
2010-08-18 12:45:47: INFO: an undead schedule has been deleted: 'pk_recvupdate'.
2010-08-18 12:45:47: INFO: Purged IPsec-SA with proto_id=ESP and spi=3642234214(0xd9181566).
The most interesting thing is that sometimes this message appears, sometimes not (with the same configuration).
Please help!Hi,
I have some problem. I am using Windows 7 Entreprice x64. I use SA520 Firmware 1.1.65 and QuickVPN 1.4.1.2 port 60443.
"The remote gateway is not responding. Do you want to wait"
2010-08-18 17:25:51: INFO: Adding IPSec configuration with identifier "username"
2010-08-18 17:25:51: INFO: Adding IKE configuration with identifer "username"
2010-08-18 17:26:04: INFO: Configuration found for xxx.xxx.xxx.xxx[235].
2010-08-18 17:26:04: INFO: Received request for new phase 1 negotiation: 172.22.5.10[500]<=>xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:04: INFO: Beginning Identity Protection mode.
2010-08-18 17:26:04: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 17:26:04: INFO: Received Vendor ID: RFC 3947
2010-08-18 17:26:04: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: Received unknown Vendor ID
2010-08-18 17:26:04: INFO: For xxx.xxx.xxx.xxx[235], Selected NAT-T version: RFC 3947
2010-08-18 17:26:04: INFO: NAT-D payload does not match for 172.22.5.10[500]
2010-08-18 17:26:04: INFO: NAT-D payload does not match for xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:04: INFO: NAT detected: ME PEER
2010-08-18 17:26:04: INFO: Floating ports for NAT-T with peer xxx.xxx.xxx.xxx[48540]
2010-08-18 17:26:04: INFO: ISAKMP-SA established for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:ed4f291c71c1b688:7e6a8a0968f878fb
2010-08-18 17:26:04: INFO: Sending Informational Exchange: notify payload[INITIAL-CONTACT]
2010-08-18 17:26:04: INFO: Responding to new phase 2 negotiation: 172.22.5.10[0]<=> xxx.xxx.xxx.xxx[0]
2010-08-18 17:26:04: INFO: Using IPsec SA configuration: 192.168.75.0/24<->192.168.170.224/32
2010-08-18 17:26:04: INFO: Adjusting peer's encmode 3(3)->Tunnel(1)
2010-08-18 17:26:05: INFO: IPsec-SA established[UDP encap 48540->4500]: ESP/Tunnel xxx.xxx.xxx.xxx->172.22.5.10 with spi=239099274(0xe405d8a)
2010-08-18 17:26:05: INFO: IPsec-SA established[UDP encap 4500->48540]: ESP/Tunnel 172.22.5.10-> xxx.xxx.xxx.xxx with spi=3886848189(0xe7ac98bd)
2010-08-18 17:26:07: INFO: Configuration found for xxx.xxx.xxx.xxx[235].
2010-08-18 17:26:07: INFO: Received request for new phase 1 negotiation: 172.22.5.10[500]<=> xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:07: INFO: Beginning Identity Protection mode.
2010-08-18 17:26:07: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 17:26:07: INFO: Received Vendor ID: RFC 3947
2010-08-18 17:26:07: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 17:26:07: INFO: Received unknown Vendor ID
2010-08-18 17:26:07: INFO: Received unknown Vendor ID
2010-08-18 17:26:07: INFO: Received unknown Vendor ID
2010-08-18 17:26:07: INFO: For xxx.xxx.xxx.xxx[235], Selected NAT-T version: RFC 3947
2010-08-18 17:26:07: INFO: NAT-D payload does not match for 172.22.5.10[500]
2010-08-18 17:26:07: INFO: NAT-D payload does not match for xxx.xxx.xxx.xxx[235]
2010-08-18 17:26:07: INFO: NAT detected: ME PEER
2010-08-18 17:26:07: INFO: Floating ports for NAT-T with peer xxx.xxx.xxx.xxx[48540]
2010-08-18 17:26:07: INFO: ISAKMP-SA established for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:699f34b434d4318c:df4adca414787d36
2010-08-18 17:27:14: INFO: Purged ISAKMP-SA with proto_id=ISAKMP and spi=699f34b434d4318c:df4adca414787d36.
2010-08-18 17:27:14: INFO: Configuration found for xxx.xxx.xxx.xxx[235].
2010-08-18 17:27:14: INFO: Received request for new phase 1 negotiation: 172.22.5.10[500]<=> xxx.xxx.xxx.xxx[235]
2010-08-18 17:27:14: INFO: Beginning Identity Protection mode.
2010-08-18 17:27:14: INFO: Received Vendor ID: MS NT5 ISAKMPOAKLEY
2010-08-18 17:27:14: INFO: Received Vendor ID: RFC 3947
2010-08-18 17:27:14: INFO: Received Vendor ID: draft-ietf-ipsec-nat-t-ike-02
2010-08-18 17:27:14: INFO: Received unknown Vendor ID
2010-08-18 17:27:14: INFO: Received unknown Vendor ID
2010-08-18 17:27:14: INFO: Received unknown Vendor ID
2010-08-18 17:27:14: INFO: For xxx.xxx.xxx.xxx[235], Selected NAT-T version: RFC 3947
2010-08-18 17:27:14: INFO: NAT-D payload does not match for 172.22.5.10[500]
2010-08-18 17:27:14: INFO: NAT-D payload does not match for xxx.xxx.xxx.xxx[235]
2010-08-18 17:27:14: INFO: NAT detected: ME PEER
2010-08-18 17:27:15: INFO: ISAKMP-SA deleted for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:699f34b434d4318c:df4adca414787d36
2010-08-18 17:27:15: INFO: Floating ports for NAT-T with peer xxx.xxx.xxx.xxx[48540]
2010-08-18 17:27:15: INFO: ISAKMP-SA established for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:3fe5eb0bddbf2b9a:f5c11d7f813ca74a
2010-08-18 17:27:15: INFO: Sending Informational Exchange: notify payload[INITIAL-CONTACT]
2010-08-18 17:28:20: INFO: Purged ISAKMP-SA with proto_id=ISAKMP and spi=3fe5eb0bddbf2b9a:f5c11d7f813ca74a.
2010-08-18 17:28:21: INFO: ISAKMP-SA deleted for 172.22.5.10[4500]- xxx.xxx.xxx.xxx[48540] with spi:3fe5eb0bddbf2b9a:f5c11d7f813ca74a
With windows XP Pro i dont have this problem.
Is there a detailed configuration guide?
10x -
Hello all
I�d really appreciate it if you could provide me your comments regarding a problem I have when using CRLs (Certificate Revocation Lists) in a Solaris-10 IPSec connection. I establish an IPSec tunnel between two servers, Solaris-10 and MS Windows 2003, and it works fine. However, when I try to implement CRLs in the Solaris conf, I get some errors in the logs and the connection doesn�t work.
At the end of the message I show you IPSec configuration I�m using. This conf works ok if I don�t use CRL. I changed the �etc/inet/ike/config� file to the following:
#ignore crls
use_http
I used OpenSSL to generate the CRL and both the servers and the CA digital certificates. I put the distribution point �http://192.168.1.1/test-crl.crl� inside the CA certificate which is in the Solaris 10 server. This HTTP server is an IIS in the other MS Windows I mentioned. I also have generated the certificates in several ways including PEM and DER trying to see what the Solaris is expecting.
I would appreciate your opinion about:
(a) Do you think the problem could be an incompatibility with the certificates and/or the CRL file formats?
(b) What is the format that Solaris supports for the certificates and CRLs?
I am also attaching the logs I got from Solaris. I guess it shows that the server can not obtain the CRL, but I�m not sure.
Thank you so much and I look forward to hearing from you at your earliest convenience,
***** IPSec conf *****
- ID Type: Fully Qualified Domain Name (FQDN)
- Phase 1 mode: Main Mode
- Authentication method: RSA Signatures
- Encryption algorithm � Phase 1: Triple DES
- Hash - Phase 1: SHA-1
- SA lifetime - Phase 1: 28800
- Diffie-Hellman group � Phase 1: Group 2
- SA lifetime - Phase 2: 1800
- IP Compression: NO
- Protocol - Phase 2: ESP
- Encryption Algorithm - Phase 2: Triple DES
- Hash - Phase 2: SHA-1
- Encapsulation: Transport Mode
- Diffie-Hellman group � Phase 2(PFS): Group 2
***** Solaris Logs *****
lun 26 sep 05 14:59:30: in.iked: In ssh_policy_find_private_key.
lun 26 sep 05 14:59:30: in.iked: Start ssh_policy_request_certificates
lun 26 sep 05 14:59:30: in.iked: Requesting certs for 1 CA's
lun 26 sep 05 14:59:31: in.iked: spsi: ike_udp_callback_common -1
lun 26 sep 05 14:59:34: in.iked: spsi: ike_udp_callback_common -1
lun 26 sep 05 14:59:38: in.iked: spsi: ike_udp_callback_common -1
lun 26 sep 05 14:59:41: in.iked: Could not retrieve certificate list, ca=0.
lun 26 sep 05 14:59:41: in.iked: spsi: ike_send_packet -1
lun 26 sep 05 14:59:41: in.iked: ssh_policy_negotiation_done_isakmp:
natt_state -1
lun 26 sep 05 14:59:41: in.iked: Phase 1 negotiation error: code 24
(Authentication failed).
*****Jason,
Thank you for your question. This community is for Cisco Small Business products and your question is in reference to a Cisco Elite/Classic product. Please post your question in the Cisco NetPro forums located here: http://forums.cisco.com/eforum/servlet/NetProf?page=main This forum has subject matter experts on Cisco Elite/Classic products that may be able to answer your question.
However, just looking at your configuration, I did see that your hashing algorithm on the YMCA side is using SHA and group 1 for isakmp policy 20 while on the Server side you are using 3des and group2 for policy 20.
Good Luck,
Bill -
IPSec timeout: "ERROR Hybrid auth negotiated but peer did not succeed Xauth
I'm using the Cisco IPSec VPN client on the iPad to connect a Linux server running racoon.
Initially the connection works fine but after a while it stalls completely due to a timeout.
Linux box logs:
13:18:00 Linux racoon: ERROR: Hybrid auth negotiated but peer did not succeed Xauth exchange
13:18:00 Linux racoon: ERROR: Attempt to start phase 2 whereas Xauth failed
13:18:03 Linux racoon: ERROR: Hybrid auth negotiated but peer did not succeed Xauth exchange
13:18:03 Linux racoon: ERROR: Attempt to start phase 2 whereas Xauth failed
iPad logs:
13:17:55 Pad racoon 719 <Info>: 719 INFO: initiate new phase 2 negotiation: 192.168.1.100[0]<=>x.x.x.x[0]
13:17:55 Pad racoon 719 <Info>: 719 INFO: NAT detected -> UDP encapsulation (ENC_MODE 1->3).
13:18:25 Pad racoon 719 <Info>: 719 ERROR: x.x.x.x give up to get IPsec-SA due to time up to wait.
Server-side racoon config:
remote anonymous
passive on;
exchange_mode aggressive,main;
my_identifier fqdn "xxxxxxxxx.xxx";
generate_policy on;
nat_traversal on;
mode_cfg on;
xauth_login "ipsecvpn";
script "p1updown" phase1_up;
script "p1updown" phase1_down;
#dpd_delay 20;
#dpd_retry 5;
#dpd_maxfail 5;
#dpd_algorithm dpdblackholedetect;
initial_contact on;
lifetime time 24 hour;
proposal_check strict;
proposal {
encryption_algorithm aes 256;
hash_algorithm sha1;
dh_group 2;
authentication_method xauthpskserver;
# authentication_method presharedkey;
mode_cfg
# auth_source pam;
auth_source system;
auth_throttle 3;
auth_source system;
save_passwd on;
conf_source local;
accounting system;
network4 10.8.1.2;
netmask4 255.255.255.0;
pool_size 255;
dns4 10.8.1.1;
# default_domain "xxxxxxxxx.xxx";
# split_network include 10.8.0.0/16;
# split_dns "xxxxxxxxx.xxx";
pfs_group 2;
sainfo anonymous
lifetime time 12 hour;
# lifetime byte 50 MB;
encryption_algorithm aes, blowfish;
authentication_algorithm hmac_sha1 ;
compression_algorithm deflate ;
pfs_group 2;
# EOF
iPad fw: 3.2.1 (same problem also with 3.2.2)
Any ideas?Re-keying issue? I dunno. The manual mentions Phase 1, and your log points to Phase 2, but maybe it's worth a shot.
"Re-keying of Phase 1: Not currently supported. Recommend that re-keying times on
the server be set to approximately one hour."
Incidentally, how do you get logs off of the iPad?
Maybe you are looking for
-
Reporting Services for Microsoft SQL Server 2008 R2 (RTM) - 10.50.1617.0
Hello, We are currently running: Microsoft SQL Server 2008 R2 (RTM) - 10.50.1617.0 (Intel X86) Apr 22 2011 11:57:00 Copyright (c) Microsoft Corporation Standard Edition on Windows NT 5.2 <X86> (Build 3790: Service Pack 2) (Hypervisor) We would l
-
Mac Pro 2014 & Samsung Legacy TV
Try to make this short. My system Rotel recievor, Mac Mini (os 10.9.3) and Seamsung Lecacy (65" 4K) works fine. Replace the Mac Mini with Mac Pro (2014) and no video. Bi-pass Rotel and video works. Interestingly the "Display" screen using OS 10.9.3
-
Adding Individual IWeb pages to existing site.
I have a website that I created not using IWeb. Can I use IWeb to create a photo gallery page and add just that page to my website. I have a ton of pages and I don't want to start over but I like the way the slide show galleries work in IWeb. I also
-
How can I get latest Norton 360 auto fill to work with FF 6.0.2?
Running Win 7 premium 64Bit- just loaded a new Norton 360 and the ID/Password autofill feature stopped working. It was working before with the same computer and Op System.
-
Hi All, Can you please send me the process codes for the following IDOC types as I could not find them in WE64. Also let me know how did you found out. IDOC types are: 1) INTERNAL_ORDER_CREATE01 2) PROFITCENTER_CREATE01 3) COSTCENTERGROUP_CREATE01 Ur