Pix 506e firewall configring for mail( Exhange), Web, FTP server

Hi
I am Hemant, We have pix 506e firewall, D-link ADSL dsl-502t and my IBM xseries 236 server.
I have fix static live ip 59.181.103.220 which i have got ISP (MTNL), and the same ip is given in fqdn in www.net4india.com (a company from where we have registered domaim name and taken space)
My problem is i am not able to send mail through my mail server (loyalindia.co.in)but i am receiving mails from any server.
My network design is as fallows:-
ADSL (WAN)59.181.103.220, ADSL (LAN)59.181.103.221. Pix 506e (out) 59.181.103.222, Pix 506e (in) 192.168.1.1. My domain mail server loyalindia.co.in (Exchange server) ip 192.168.1.2
I am tryied with (ADSL)natting and without natting but the problem is same.
If i am removing the pix 506e and directly connecting the server to adsl i am able to receive and send mails properly.
can anybody who can support me?.

Hello
I think there won't be one QUCK START to get all of this up and running, there are multiple examples on the following page, a few that might help would be:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/prod_configuration_examples_list.html
PIX/ASA : Connecting Three Internal Networks with Internet Configuration Example
PIX/ASA : Connecting Two Internal Networks with Internet Configuration Example
ASA 7.x/PIX 6.x and Above: Open/Block the Ports Configuration Example
PIX/ASA 7.x: Enable VoIP (SIP, MGCP, H323, SCCP) Services Configuration Example
PIX/ASA 7.x and FWSM: NAT and PAT Statements
PIX/ASA 7.x and later : Port Redirection(Forwarding) with nat, global, static and access-list Commands
Configuring PIX Firewall with Mail Server Access on the DMZ
Configuring the PIX Firewall with Mail Server Access on Inside Network
Please rate if you find the post helpful.
Regards
Farrukh

Similar Messages

Trigger aler or send a mail if target ftp server is down

Hi,
I am sending file from source to target using XI.
Here my target is FTP. If the FTP server is down on the target side while placing the file we need to trigger an alert or send an email to the sender.
Thanks & Regards
Sowmya.

Once the adapter engine tries for the standard retry time and interval, it will change the message status to System Error.
Create Alert Rule for the Adapter Engine errorrs. SelectAdapter Engine and make the adapter type as All. Rest is same
The specified item was not found.
Regards,
Prateek

10.4.2 upgrade to 10.4.8... web/ftp server.. what to look out for?

Anything I should be aware of.
I backed up all of my data, including configs httpd, and other shared apps like squirrelmail, roundcube, phpicalendar.(just in case the update decides it wants to wipe the dir completely)
I have heard about issues with mysql SOCK, but have not kept up to date on what the updates may or may not effect.
Curious what people's issues have been throughout the updates to 10.4.8.
I suppose I could read through all of the threads, but I would kind of like a rundown of things to checkout, before I commit to this update.
P.S. I ASR'ed the booted OS onto another drive, just in case I have to revert while figuring out the solution's to the problems.

Looks like everything went fine.
I decided to do a target disk mode install of the combo update. The problem I ran into is that my MacBook Pro was unable to install the PPC combo update, since it is not a PPC. So I had to use my old powerbook.
Some of my squirrelmail configs were off, but easy to re-implement. Even some of my hacked passwd plugins and seive plugins were fine.

Linksys WRT600N vs CISCO PIX 506E.... Firewall / Routing Performance

Hi:
I am new to the forum and was hoping to tap into some of your expertise. I have a Linksys WRT600N version 1.1 and I recently acquired a CISCO PIX 506E firewall. My question is what should I use as a firewall? Both have SPI etc. Should I:
a) Use the 506E as a firewall and use the 600 as a wireless access point, or
b) Use the 600 as a firewall and wireless access point.
Do both routers have the same firewall routing performance? I want to use the storage feautre on the 600N, but if I do that and use it as a wireless access point the 600 can't get the proper time from the Internet, so my time for newly created folders and files shows they are 10 years old.
Anyway, just thought I would post and find out what some of the experts thought and maybe someone from Linksys or CISCO. I know the 506E is discontinued and was manufactured around 2001 and the 600N is a new model.
(Edited subject to keep threads from stretching. Thanks!)
Message Edited by JOHNDOE_06 on 05-06-2008 10:41 AM

The PIX is a real firewall. The WRT has a firewall which mostly protects the router itself. People prefer to buy a "SPI firewall router" instead of a simple "router" even though the router firewall does nothing or little to protect the LAN. The only firewall configurations on the WRTs you can usually do is on the Access Restrictions tab. But that's usually all. The LAN itself is not protected by the firewall. You would notice this if you had a public IP subnet and ran it through the WRT: the LAN would be fully exposed to the internet. Some routers have a few functions like protection against denial of service attacks or similar. But even then this often filters only the traffic targeted at the router and not the LAN.
The common protection of your LAN you have on the WRT is because you use private IP addresses inside your LAN and the router does NAT. However, NAT is not a security mechanism but a mechanism to solve the problem that you can only have a single public IP address but want to use multiple computers, which is why you have to use private IP addresses. Current NAT implementations usually drop unsolicited incoming traffic because they don't know to which IP address in the LAN to send it to. But the notion of NAT is to deliver and to allow connectivity. This has nothing to do with security or a firewall.
Thus, if you want to use a real firewall use the PIX. On the PIX you can configure the traffic which is allowed to enter the LAN and which not. It is far superior in this respect to the WRT. However, as it is a older model, I cannot tell how fast the PIX is. You should be able to find the old data sheets of the PIX somewhere on the cisco website. They should mention the possible throughput. I guess it won't be an issue.
To me another point for the PIX are the VPN capabilities which allow you to securely access your LAN while you are on the road.
Of course, you must know how to configure the PIX correctly. It is a complex device and can be configured pretty much for anything you like. This means of course if you do it wrong you may end up with little or no security.
BTW, there are no people from linksys in this forums except the moderators (which may be from lithium). To hear from Linksys you have to contact Linksys support.

Pix 506e

Hi,
We have planning to Purchase Cisco Pix 506E Firewall. We are having 50
Computers & Users.If we purchase Pix 506E Firewall,its require to purchase
any aditional license.
with regds
prem

For the PIX 506E there is only one license that can be purchased which is the 3DES/AES and DES Encryption Licenses. Right now I think you can download that license for free. The following link will provide you with details on that license and the data sheet on that PIX (scroll down about half way for the license information).
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b13.html
The following link will give you the data sheet and describe the three different licenses available with upper models of the PIX as it relates to the 515E (restricted, unrestricted, and failover).
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_data_sheet09186a0080091b15.html

How to change Content-Transfer-Encoding for mail sending

Hello Experts,
I need to send some documents through mail which i am doing with the help of cl_output_service=>document_output method. Mail is been send succesfully.
But in the payload content which got from Exchange server:
   X-Mailer: SAP Web Application Server 7.10
   Content-Type: text/plain;
    charset="us-ascii"
   Content-Transfer-Encoding: quoted-printable
Can any one help me, how i can change Content-Transfer-Encoding field to some other format which is not 'quoted-printable'.
Thanks & Regards,
Dheeraj

Do you documents contain an XML Declaration like this at the top?
<?xml version="1.0" encoding="ISO-8859-2"?>
If not, then they need to. The XML 1.0 specification says that if an XML declaration is not present, the processor must default to assume its in UTF-8 encoding.

Edit catt script for changes in in web appl server higher than 6.4 release

Hello Gurus,
Will you help me in editing the CATT script for changes in Web application server release higher than 6.4 release, when I look for edit mode it was showing the following message. will anyone suggest me is there any way to make changes.
While I was choosing change mode it was displaying the above message ( Message No:TT005)
Full points for the answer

It seems there there is no problem with my FireFox 7.0.1 on my Mac OSX 10.7.2. So, maybe you can solve the problem by updating your OS. The only minor problem here is that Firefox doesn't display in the Tibetan fonts that you choose, it always display in Kailas font for Tibetan.

Office Web Apps Server 2013 - No download Volume Licensing Service Center

I´m looking for a office web apps server 2013 (OWS) download.
In the following blog Microsoft is announcing that the OWS is moving from the Download Center to the Volume Licensing Service Center (VLSC).
http://blogs.technet.com/b/office_sustained_engineering/archive/2014/10/22/web-apps-server-removal-from-download-center.aspx
So far so good
But in my VLSC are only Updates and Service Packs for the OWS. But no download for the OWS!
Is this only my problem? Any ideas to solve this problem?

Hi,
You can contact the Volume Licensing Service Center to get the answer to this case.
Refer to this link below, and select your country to get the Support Center Contact Information:
https://www.microsoft.com/licensing/servicecenter/Help/Contact.aspx
Regards,
Melon Chen
TechNet Community Support
It's recommended to download and install
Configuration Analyzer Tool (OffCAT), which is developed by Microsoft Support teams. Once the tool is installed, you can run it at any time to scan for hundreds of known issues in Office
programs.

Hosting Multiple Mail Domains in SL server on a Mac Mini

So I have been trying to find out the answer to this question, and I keep getting conflicting information, and I am hoping someone here can help me solve this.
We are running two very small business with two different Domains (@company1 & @Company2) Each company has a website, and corporate email. All I want to do is bring all of this in-house onto one Mac Mini server. The calendars and contacts will be shared between the two principle owners of each company (my bosses) as they support each other in there individual business.
The Apple "Genius" says this is not possible, I believe and have been told by a few people and after reading posts on here that it is possible to have multiple domains on one Mac Mini Server. I would like to figure this out quickly as the companies have a need to move off the current email provider as fast as possible due to complications with iOS4 and the iPads.
Any Help from people who are doing this, or know it to be possible or impossible would be greatly appreciated!

This is entirely possible, and supported by the Server Admin user interface for the mail server.
Start with the [Mac OS X Server Mail Services Administration Manual|http://images.apple.com/server/macosx/docs/MailService_Adminv10.6.pdf], page 73
Quoth the Book Of Mail:
A Mail Service Virtual Host
Virtual hosting is a method you can use to host more than one domain name on the same
computer and IP address, with overlapping mail user names.
For example, a mail server can receive mail transfer requests for two domains,
mail.example1.com and mail.example2.com, both of which resolve to the same IP
address. For mail.example1.com, the server delivers mail to “[email protected]”
to a user mailbox for “bob,” while it also delivers mail to “[email protected]” to
a different user mailbox. Virtual hosts are essentially the converse of local host aliases.
One subtlety here is that the domains sharing the same mail server and all co-resident on the IP address will all tend to have the same public host name listed as their MX (mail exchange) server of record in the public DNS. This so that forward and reverse DNS and MX server all line up for the mail server for all the domains involved.

Can i use office web app server without adding to a domain ?

spserver.local is my domain controller webapp.spsserver.local is my office web app server(OWA)(IP:79.123.161.xxx )
I manage to use office web app with sharepoint 2013 my OWA is in a domain (spserver.local) and it's address is http://webapp.spserver.local/hosting/discovery There
is no problem. But I want to seperate OWA with Sharepoint and its domain I want to remove the domain.Is it possible?
For example my OWA's ip is 79.123.161.xxx
I want to work like this: http://79.123.161.xxx/hosting/discovery
When I enter the path http://79.123.161.xxx/hosting/discovery there
is an iis message "File or directory not found."

Are you asking if you can have your OWA in different domain compared to SharePoint server domain or are you asking that your OWA does not belong to any domain and you still want to use it with SharePoint?
If your question is regarding using OWA in different domain then I think (someone can correct me if I am wrong) OWA can run into different domain. You just need to add your SharePoint Server host domain to the Allow List for an Office Web Apps Server farm.
http://technet.microsoft.com/en-us/library/jj219459.aspx
If your question is related to OWA not belonging to any domain then I do not think that will work and its not supported scenario. If you read the following article it states
"All servers in the Office Web Apps Server farm must be part of a domain. They can be in the same domain (recommended) or in domains that are in the same forest. However, Office Web Apps Server won’t work if you try to install it on a domain controller."
http://technet.microsoft.com/en-us/library/jj219435.aspx
Amit

How do I change the URL to the Remote Web Access server in Windows Server 2012?

Hallo!
I have set up a Remote Dexktop Service using the "Quick" deployment method in Server Manager and everything is working greate internally, but I cannot start an app published in Remote Web Access from outside our network.
The problem is that it wants to start the using the internal URL, for example, server.domain.local, instead of the external one, for example remote.server.com.
I therefore want to know how I can change the default URL for the Remote Web Access server and all the Remote Web Apps in Windows Server 2012?
I have allready looked in Server Manager and I can change some of the deployment settings in server manager, but there is no way to alter the URL of the Remote Web Access server. See below images:
Pressing the internal URL only results in opening the internal URL.
This was very simple to do in Windows Server 2008 R2 using the tsconfig tool, but it does not seam to be any way of solving this in server manager.
A possible sollution would be to alter the registry someware in HKLM->Software->Microsoft->Windows NT->Terminal Services. But this can easaly lead to problems due to wrong format, etc. and is probably not supported.
Is there a simpler and supported way?

That option can be used to connect to any machine that you want. The error message indicates that the client machine cannot resolve the name "server.domain.local" to an IP address that it can connect to.
You have several options for configuring that tab on the RDweb site. You can even remove it entirely.
Customization of RD Web Site
RD Web provides a number of customization options for the RD Web interface, including the ability to control default Gateway server settings and redirection settings. These settings
are controlled by editing the web.config file located in %SYSTEMROOT%\Web\RDWeb\Pages.
Displaying Local Help
To display local help for users instead of the web-based help, edit the LocalHelp value and change the value from false to true.

<add key="LocalHelp" value="false" />
When this value is changed, a user that clicks on Help in the upper right corner of the RD Web login page will open the local help file instead of web-based help.
Hiding the Connect to a Remote PC Tab
The RDWeb page
Connect to a Remote PC tab can be hidden from users to prevent connections to any servers through RD Web other than the servers configured in a collection. By default, this setting is set to true and the
Remote Desktops tab is displayed. To hide the tab, set the value to false.

<add key="ShowDesktops" value="true" />
When the value is set to false, a user will not see the Connect to a Remote PC tab when logged on to the RD Web page
RD Gateway Settings
If the Connect to a Remote PC tab is enabled, an administrator can configure RD Web to use a Gateway server when connecting to remote computers. To specify a gateway, edit the below
value with the name of the RD Gateway server:

<add key="DefaultTSGateway" value="" />
The default authentication method for the RD Gateway server can also be configured by editing the following section of the web.config:

<add key="GatewayCredentialsSource" value="0" />
Devices and Resources
By default, only Printers and Clipboard are redirected on connections made using the Connect to a Remote PC tab. If the user clicks the
Options << button, the redirection settings for a specific connection can be modified
To configure each specified redirection option to be enabled or disabled by default, edit the following section in the web.config file:

<add key="xPrinterRedirection" value="true" />
<add key="xClipboard" value="true" />
<add key="xDriveRedirection" value="false" />
<add key="xPnPRedirection" value="false" />
<add key="xPortRedirection" value="false" />
LAN Experience Defaults
Windows Server 2012 RD Web Access can display a new user selectable option for optimizing the connection for a LAN experience. This option is displayed at the bottom of the RD Web
page and can be controlled by the administrator using the following section of the web.config file:

<add key="ShowOptimizeExperience" value="false" />
<add key="OptimizeExperienceState" value="false" />
This value is set to false by default, but when changed to true, the following checkbox will display at the bottom of the webpage. The LAN experience
checkbox can also be set as enabled by default.
Each setting can also be modified using the IIS Manager user interface:
Don Geddes - SR Support Escalation Engineer - Remote Desktop Services - Printing and Imaging

Rtf-Vulnerability in Office 2013 Web Apps Server

I was trying to install a hotfix for our Office Web Apps server because of the vulnerability listed here:
http://technet.microsoft.com/en-us/security/advisory/2953095
The suggested solution is installing a hotfix (http://technet.microsoft.com/en-us/security/advisory/2953095). But when trying to install it on our Office Web Apps server (Windows Server 2012), I just a message that it can't be installed on this operating
system or for this version of the application.
How do I install the hotfix or disable RTF content for the Word Web Apps server?

Hi Lakner,
According to your description, my understanding is that the hotfix cannot be installed in Office Web Apps Server 2013.
As the articles below said, “the affected versions include Word 2003, 2007, 2010, Office for Mac 2011, Office Web Apps 2010 and Office Web Apps Server 2013. However, Microsoft said the active attacks have only targeted those systems running
Word 2010.”
http://redmondmag.com/articles/2014/03/25/office-0day-exploit.aspx
http://blogs.technet.com/b/srd/archive/2014/03/24/security-advisory-2953095-recommendation-to-stay-protected-and-for-detections.aspx
Best regards.
Thanks
Victoria Xia
TechNet Community Support

Web Logic Server in IBM Power 6 Based (AIX 6.1)

Hi,
Please share the documentation for 11g R1 Web Logic Server in IBM Power 6 Based (AIX 6.1) cluster environment.
Regards,

Hi
You could review Oracle® Fusion Middleware High Availability Guide 11g Release 1 (11.1.1) at
http://download.oracle.com/docs/cd/E14571_01/core.1111/e10106/aa.htm#CFADJHAC
regards

Upgrade question (iPlanet Web Proxy Server)

Hello List,
What is the procedure for upgrading iPlanet Web Proxy Server 3.6 (beta)
to iPlanet Web Proxy Server 3.6 on Solaris 2.8?
Thank you in advance.
- Andrew Petrov.

Hi
This as per the HTTP/1.1 RFC (RFC2616)
The Connection general-header field allows the sender to specify options that are desired for that particular connection and MUST NOT be communicated by proxies over further connections.
The Connection header has the following grammar:
Connection = "Connection" ":" 1#(connection-token)
connection-token = token
HTTP/1.1 proxies MUST parse the Connection header field before a message is forwarded and, for each connection-token in this field, remove any header field(s) from the message with the same name as the connection-token. Connection options are signaled by the presence of a connection-token in the Connection header field, not by any corresponding additional header field(s), since the additional header field may not be sent if there are no parameters associated with that connection option.
Read the following at
http://www.w3.org/Protocols/rfc2616/rfc2616-sec8.html#sec8.1.3
and
http://www.w3.org/Protocols/rfc2616/rfc2616-sec14.html#sec14.10
Regards
Nagendra HK

JDev Integrated Web Logic Server fails

I'm a newbie with WLS. I've installed JDEV 11.1.1.3 in Windows XP SP3, and installed extensions for Webcenter.
Now trying to go through webcenter tutorial, I arrived at point where I'm trying to run a small application,
but nothing works. I've searched and searched the internet for clues, help, and tried multiple things, but nothing helps.
First, I get the warning message
Warning> <Server> <BEA-002611> <Hostname "XXX", maps to multiple IP addresses: 10.10.10.10, 169.254.25.129, 192.168.2.6
and then when I disable all the network connections for these IPs, just to see if this would help,
then the server appears to start successfully, but the tutorial app that compiled successfully does not start to run in any brower.
I go through the properties of the Application Server for the Integrated Web Logic Server to test the connection and I get
Testing JSR-160 Runtime ... failed.
Cannot establish connection.
Testing JSR-160 DomainRuntime ... skipped.
Testing JSR-88 ... skipped.
Testing JSR-88-LOCAL ... skipped.
Testing JNDI ... skipped.
Testing JSR-160 Edit ... skipped.
Testing HTTP ... failed.
Unable to open conection: Connection refused: connect
Testing Server MBeans Model ... skipped.
I have no clue, and trying different configurations does not help.
I need a WebLogic for Dummies guide. Anyone have some clue ?

Thanks Ravi Jegga for looking at my post. Here's some info.
1) Here's the log output for starting Server Instance (IntegratedWebLogicServer)
*** Using port 7101 ***
"C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\bin\startWebLogic.cmd"
[waiting for the server to complete its initialization...]
JAVA Memory arguments: -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m -XX:MaxPermSize=512m
WLS Start Mode=Development
CLASSPATH=C:\oracle\MIDDLE~1\WLSERV~1.3\server\ext\jdbc\oracle\11g\ojdbc6dms.jar;C:\oracle\MIDDLE~1\patch_wls1033\profiles\default\sys_manifest_classpath\weblogic_patch.jar;C:\oracle\MIDDLE~1\patch_jdev1111\profiles\default\sys_manifest_classpath\weblogic_patch.jar;C:\oracle\MIDDLE~1\JDK160~1\lib\tools.jar;C:\oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic_sp.jar;C:\oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.jar;C:\oracle\MIDDLE~1\modules\features\weblogic.server.modules_10.3.3.0.jar;C:\oracle\MIDDLE~1\WLSERV~1.3\server\lib\webservices.jar;C:\oracle\MIDDLE~1\modules\ORGAPA~1.1/lib/ant-all.jar;C:\oracle\MIDDLE~1\modules\NETSFA~1.0_1/lib/ant-contrib.jar;C:\oracle\Middleware\jdeveloper\webcenter\modules\oracle.portlet.server_11.1.1\oracle-portlet-api.jar;C:\oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrf.jar;C:\oracle\MIDDLE~1\WLSERV~1.3\common\derby\lib\derbyclient.jar;C:\oracle\MIDDLE~1\WLSERV~1.3\server\lib\xqrl.jar
PATH=C:\oracle\MIDDLE~1\patch_wls1033\profiles\default\native;C:\oracle\MIDDLE~1\patch_jdev1111\profiles\default\native;C:\oracle\MIDDLE~1\WLSERV~1.3\server\native\win\32;C:\oracle\MIDDLE~1\WLSERV~1.3\server\bin;C:\oracle\MIDDLE~1\modules\ORGAPA~1.1\bin;C:\oracle\MIDDLE~1\JDK160~1\jre\bin;C:\oracle\MIDDLE~1\JDK160~1\bin;C:\oracle\product\10.2.0\db_4\BIN;C:\OracleBI\server\Bin;C:\OracleBI\web\bin;C:\OracleBI\web\catalogmanager;C:\OracleBI\SQLAnywhere;C:\product\10.1.3.1\OracleAS_5\jdk\bin;C:\product\10.1.3.1\OracleAS_5\jdk\jre\bin\client;C:\product\10.1.3.1\OracleAS_5\jdk\jre\bin;C:\product\10.1.3.3\OracleBIP\jre\1.4.2\bin\client;C:\product\10.1.3.3\OracleBIP\jre\1.4.2\bin;C:\product\10.1.3.1\OracleAS_5\ant\bin;C:\product\10.1.3.1\OracleAS_5\bin;C:\oracle\product\10.2.0\db_4\BIN;C:\oraclexe\app\oracle\product\10.2.0\server\bin;C:\Ora_10g2_DevSuite\jdk\jre\bin\classic;C:\Ora_10g2_DevSuite\jdk\jre\bin;C:\Ora_10g2_DevSuite\jdk\jre\bin\client;C:\Ora_10g2_DevSuite\jlib;C:\Ora_10g2_DevSuite\bin;C:\Ora_10g2_DevSuite\jre\1.4.2\bin\client;C:\Ora_10g2_DevSuite\jre\1.4.2\bin;C:\WINDOWS\system32;C:\WINDOWS;C:\WINDOWS\System32\Wbem;C:\Program Files\Symantec\pcAnywhere\;C:\MKS\mksnt;C:\Program Files\QuickTime\QTSystem\;C:\WINDOWS\system32\WindowsPowerShell\v1.0;C:\oracle\MIDDLE~1\WLSERV~1.3\server\native\win\32\oci920_8
* To start WebLogic Server, use a username and *
* password assigned to an admin-level user. For *
* server administration, use the WebLogic Server *
* console at http:\\hostname:port\console *
starting weblogic with Java version:
java version "1.6.0_18"
Java(TM) SE Runtime Environment (build 1.6.0_18-b07)
Java HotSpot(TM) Client VM (build 16.0-b13, mixed mode)
Starting WLS with line:
C:\oracle\MIDDLE~1\JDK160~1\bin\java -client -Xms256m -Xmx512m -XX:CompileThreshold=8000 -XX:PermSize=128m -XX:MaxPermSize=512m -Dweblogic.Name=DefaultServer -Djava.security.policy=C:\oracle\MIDDLE~1\WLSERV~1.3\server\lib\weblogic.policy -Djavax.net.ssl.trustStore=C:\oracle\Middleware\wlserver_10.3\server\lib\DemoTrust.jks -Dhttp.proxyHost=emeacache.uk.oracle.com -Dhttp.proxyPort=80 -Dhttp.nonProxyHosts=null -Dhttps.proxyHost=emeacache.uk.oracle.com -Dhttps.proxyPort=80 -Dhttps.nonProxyHosts=null -Dweblogic.nodemanager.ServiceEnabled=true -Xverify:none -da -Dplatform.home=C:\oracle\MIDDLE~1\WLSERV~1.3 -Dwls.home=C:\oracle\MIDDLE~1\WLSERV~1.3\server -Dweblogic.home=C:\oracle\MIDDLE~1\WLSERV~1.3\server -Djps.app.credential.overwrite.allowed=true -Ddomain.home=C:\DOCUME~1\jaudet\APPLIC~1\JDEVEL~1\SYSTEM~1.60\DEFAUL~1 -Dcommon.components.home=C:\oracle\MIDDLE~1\ORACLE~1 -Djrf.version=11.1.1 -Dorg.apache.commons.logging.Log=org.apache.commons.logging.impl.Jdk14Logger -Djrockit.optfile=C:\oracle\MIDDLE~1\ORACLE~1\modules\oracle.jrf_11.1.1\jrocket_optfile.txt -Doracle.domain.config.dir=C:\DOCUME~1\jaudet\APPLIC~1\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1 -Doracle.server.config.dir=C:\DOCUME~1\jaudet\APPLIC~1\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\servers\DefaultServer -Doracle.security.jps.config=C:\DOCUME~1\jaudet\APPLIC~1\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\fmwconfig\jps-config.xml -Djava.protocol.handler.pkgs=oracle.mds.net.protocol -Digf.arisidbeans.carmlloc=C:\DOCUME~1\jaudet\APPLIC~1\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\carml -Digf.arisidstack.home=C:\DOCUME~1\jaudet\APPLIC~1\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\config\FMWCON~1\arisidprovider -Dweblogic.alternateTypesDirectory=C:\oracle\MIDDLE~1\ORACLE~1\modules\oracle.ossoiap_11.1.1,C:\oracle\MIDDLE~1\ORACLE~1\modules\oracle.oamprovider_11.1.1 -Dweblogic.jdbc.remoteEnabled=false -Dwsm.repository.path=C:\DOCUME~1\jaudet\APPLIC~1\JDEVEL~1\SYSTEM~1.60\DEFAUL~1\oracle\store\gmds -DUSE_JAAS=false -Djps.policystore.hybrid.mode=false -Djps.combiner.optimize.lazyeval=true -Djps.combiner.optimize=true -Djps.auth=ACC -Doracle.core.ojdl.logging.usercontextprovider=oracle.core.ojdl.logging.impl.UserContextImpl -Doracle.wc.openusage.clustername=localhost -Doracle.wc.openusage.collectorport=31314 -Doracle.wc.openusage.timeout=30 -Doracle.wc.openusage.unicast=true -Doracle.wc.openusage.enabled=false -Doracle.webcenter.tagging.scopeTags=false -XX:+UseParallelGC -XX:+DisableExplicitGC -Dwc.oracle.home=C:\oracle\Middleware\jdeveloper -Dweblogic.management.discover=true -Dwlw.iterativeDev= -Dwlw.testConsole= -Dwlw.logErrorsToConsole= -Dweblogic.ext.dirs=C:\oracle\MIDDLE~1\patch_wls1033\profiles\default\sysext_manifest_classpath;C:\oracle\MIDDLE~1\patch_jdev1111\profiles\default\sysext_manifest_classpath weblogic.Server
<Oct 5, 2010 11:01:47 AM EDT> <Notice> <WebLogicServer> <BEA-000395> <Following extensions directory contents added to the end of the classpath:
C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\lib\mbeantypes\csp-id-asserter.jar>
<Oct 5, 2010 11:01:48 AM EDT> <Info> <WebLogicServer> <BEA-000377> <Starting WebLogic Server with Java HotSpot(TM) Client VM Version 16.0-b13 from Sun Microsystems Inc.>
<Oct 5, 2010 11:01:52 AM EDT> <Info> <Management> <BEA-141107> <Version: WebLogic Server 10.3.3.0 Fri Apr 9 00:05:28 PDT 2010 1321401 >
<Oct 5, 2010 11:01:55 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STARTING>
<Oct 5, 2010 11:01:55 AM EDT> <Info> <WorkManager> <BEA-002900> <Initializing self-tuning thread pool>
<Oct 5, 2010 11:01:56 AM EDT> <Notice> <LoggingService> <BEA-320400> <The log file C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\servers\DefaultServer\logs\DefaultServer.log will be rotated. Reopen the log file if tailing has stopped. This can happen on some platforms like Windows.>
<Oct 5, 2010 11:01:56 AM EDT> <Notice> <LoggingService> <BEA-320401> <The log file has been rotated to C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\servers\DefaultServer\logs\DefaultServer.log00008. Log messages will continue to be logged in C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\servers\DefaultServer\logs\DefaultServer.log.>
<Oct 5, 2010 11:01:57 AM EDT> <Notice> <Log Management> <BEA-170019> <The server log file C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\servers\DefaultServer\logs\DefaultServer.log is opened. All server side log events will be written to this file.>
<Oct 5, 2010 11:02:10 AM EDT> <Notice> <Security> <BEA-090082> <Security initializing using security realm myrealm.>
<Oct 5, 2010 11:02:28 AM EDT> <Warning> <Deployer> <BEA-149617> <Non-critical internal application uddi was not deployed. Error: [Deployer:149158]No application files exist at 'C:\oracle\MIDDLE~1\WLSERV~1.3\server\lib\uddi.war'.>
<Oct 5, 2010 11:02:28 AM EDT> <Warning> <Deployer> <BEA-149617> <Non-critical internal application uddiexplorer was not deployed. Error: [Deployer:149158]No application files exist at 'C:\oracle\MIDDLE~1\WLSERV~1.3\server\lib\uddiexplorer.war'.>
<Oct 5, 2010 11:02:28 AM EDT> <Warning> <Deployer> <BEA-149617> <Non-critical internal application consoleapp was not deployed. Error: [Deployer:149158]No application files exist at 'consoleapp'.>
<Oct 5, 2010 11:02:28 AM EDT> <Warning> <Deployer> <BEA-149617> <Non-critical internal application wlstestclient was not deployed. Error: [Deployer:149158]No application files exist at 'wlstestclient'.>
<Oct 5, 2010 11:02:31 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STANDBY>
<Oct 5, 2010 11:02:31 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to STARTING>
<ServerMessages><warningMsgFailedLoadingPipeline> Unable to load the webservices management interceptor pipeline
java.security.AccessControlException: access denied (oracle.security.jps.JpsPermission IdentityAssertion)
     at java.security.AccessControlContext.checkPermission(AccessControlContext.java:323)
     at java.security.AccessController.checkPermission(AccessController.java:546)
     at oracle.security.jps.util.JpsAuth$AuthorizationMechanism$3.checkPermission(JpsAuth.java:378)
     at oracle.security.jps.util.JpsAuth.checkPermission(JpsAuth.java:438)
     at oracle.security.jps.util.JpsAuth.checkPermission(JpsAuth.java:460)
     at oracle.security.jps.internal.jaas.AbstractSubjectSecurity.checkPermission(AbstractSubjectSecurity.java:113)
     at oracle.security.jps.internal.jaas.AbstractSubjectSecurity.getActionExecutor(AbstractSubjectSecurity.java:76)
     at oracle.wsm.policyaccess.impl.PMPolicyResolverBase$2.run(PMPolicyResolverBase.java:209)
     at oracle.wsm.policyaccess.impl.PMPolicyResolverBase$2.run(PMPolicyResolverBase.java:207)
     at java.security.AccessController.doPrivileged(Native Method)
     at oracle.wsm.policyaccess.impl.PMPolicyResolverBase.getActionExecutor(PMPolicyResolverBase.java:206)
     at oracle.wsm.policyaccess.impl.PMPolicyResolverBase.init(PMPolicyResolverBase.java:100)
     at oracle.wsm.policyaccess.impl.remote.RemotePolicyResolver.init(RemotePolicyResolver.java:116)
     at oracle.wsm.policyaccess.impl.PolicyAccessResolver.getResolver(PolicyAccessResolver.java:169)
     at oracle.wsm.policyaccess.impl.PolicyAccessResolver.getResolver(PolicyAccessResolver.java:98)
     at oracle.wsm.policyaccess.impl.PolicyAccessorImpl.getPolicySetMap(PolicyAccessorImpl.java:412)
     at oracle.wsm.policyaccess.impl.PolicyAccessorImpl.getPolicySet(PolicyAccessorImpl.java:379)
     at oracle.integration.platform.common.mgmt.PolicyCacheImpl$CacheNode.refreshIfStale(PolicyCacheImpl.java:142)
     at oracle.integration.platform.common.mgmt.PolicyCacheImpl.getPolicySet(PolicyCacheImpl.java:247)
     at oracle.j2ee.ws.server.mgmt.runtime.SuperServerInterceptorPipeline.forcePolicyLoad(SuperServerInterceptorPipeline.java:192)
     at oracle.j2ee.ws.server.mgmt.runtime.SuperServerInterceptorPipeline.<init>(SuperServerInterceptorPipeline.java:68)
     at oracle.j2ee.ws.server.JAXRPCProcessor.createAndInitWsmgmtInterceptor(JAXRPCProcessor.java:919)
     at oracle.j2ee.ws.server.JAXRPCProcessor.init(JAXRPCProcessor.java:877)
     at oracle.j2ee.ws.server.JAXRPCServlet.init(JAXRPCServlet.java:252)
     at javax.servlet.GenericServlet.init(GenericServlet.java:241)
     at weblogic.servlet.internal.StubSecurityHelper$ServletInitAction.run(StubSecurityHelper.java:283)
     at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
     at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
     at weblogic.servlet.internal.StubSecurityHelper.createServlet(StubSecurityHelper.java:64)
     at weblogic.servlet.internal.StubLifecycleHelper.createOneInstance(StubLifecycleHelper.java:58)
     at weblogic.servlet.internal.StubLifecycleHelper.<init>(StubLifecycleHelper.java:48)
     at weblogic.servlet.internal.ServletStubImpl.prepareServlet(ServletStubImpl.java:539)
     at weblogic.servlet.internal.WebAppServletContext.preloadServlet(WebAppServletContext.java:1976)
     at weblogic.servlet.internal.WebAppServletContext.loadServletsOnStartup(WebAppServletContext.java:1950)
     at weblogic.servlet.internal.WebAppServletContext.preloadResources(WebAppServletContext.java:1869)
     at weblogic.servlet.internal.WebAppServletContext.start(WebAppServletContext.java:3126)
     at weblogic.servlet.internal.WebAppModule.startContexts(WebAppModule.java:1512)
     at weblogic.servlet.internal.WebAppModule.start(WebAppModule.java:486)
     at weblogic.application.internal.flow.ModuleStateDriver$3.next(ModuleStateDriver.java:425)
     at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:41)
     at weblogic.application.internal.flow.ModuleStateDriver.start(ModuleStateDriver.java:119)
     at weblogic.application.internal.flow.ScopedModuleDriver.start(ScopedModuleDriver.java:200)
     at weblogic.application.internal.flow.ModuleListenerInvoker.start(ModuleListenerInvoker.java:247)
     at weblogic.application.internal.flow.ModuleStateDriver$3.next(ModuleStateDriver.java:425)
     at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:41)
     at weblogic.application.internal.flow.ModuleStateDriver.start(ModuleStateDriver.java:119)
     at weblogic.application.internal.flow.StartModulesFlow.activate(StartModulesFlow.java:27)
     at weblogic.application.internal.BaseDeployment$2.next(BaseDeployment.java:1267)
     at weblogic.application.utils.StateMachineDriver.nextState(StateMachineDriver.java:41)
     at weblogic.application.internal.BaseDeployment.activate(BaseDeployment.java:409)
     at weblogic.application.internal.EarDeployment.activate(EarDeployment.java:58)
     at weblogic.application.internal.DeploymentStateChecker.activate(DeploymentStateChecker.java:161)
     at weblogic.deploy.internal.targetserver.AppContainerInvoker.activate(AppContainerInvoker.java:79)
     at weblogic.deploy.internal.targetserver.BasicDeployment.activate(BasicDeployment.java:184)
     at weblogic.deploy.internal.targetserver.BasicDeployment.activateFromServerLifecycle(BasicDeployment.java:361)
     at weblogic.management.deploy.internal.DeploymentAdapter$1.doActivate(DeploymentAdapter.java:51)
     at weblogic.management.deploy.internal.DeploymentAdapter.activate(DeploymentAdapter.java:200)
     at weblogic.management.deploy.internal.AppTransition$2.transitionApp(AppTransition.java:30)
     at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:261)
     at weblogic.management.deploy.internal.ConfiguredDeployments.transitionApps(ConfiguredDeployments.java:220)
     at weblogic.management.deploy.internal.ConfiguredDeployments.activate(ConfiguredDeployments.java:169)
     at weblogic.management.deploy.internal.ConfiguredDeployments.deploy(ConfiguredDeployments.java:123)
     at weblogic.management.deploy.internal.DeploymentServerService.resume(DeploymentServerService.java:180)
     at weblogic.management.deploy.internal.DeploymentServerService.start(DeploymentServerService.java:96)
     at weblogic.t3.srvr.SubsystemRequest.run(SubsystemRequest.java:64)
     at weblogic.work.ExecuteThread.execute(ExecuteThread.java:201)
     at weblogic.work.ExecuteThread.run(ExecuteThread.java:173)
<Oct 5, 2010 11:03:15 AM EDT> <Notice> <LoggingService> <BEA-320400> <The log file C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\servers\DefaultServer\logs\DefaultDomain.log will be rotated. Reopen the log file if tailing has stopped. This can happen on some platforms like Windows.>
<Oct 5, 2010 11:03:15 AM EDT> <Notice> <LoggingService> <BEA-320401> <The log file has been rotated to C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\servers\DefaultServer\logs\DefaultDomain.log00008. Log messages will continue to be logged in C:\Documents and Settings\jaudet\Application Data\JDeveloper\system11.1.1.3.37.56.60\DefaultDomain\servers\DefaultServer\logs\DefaultDomain.log.>
<Oct 5, 2010 11:03:15 AM EDT> <Notice> <Log Management> <BEA-170027> <The Server has established connection with the Domain level Diagnostic Service successfully.>
<Oct 5, 2010 11:03:19 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to ADMIN>
<Oct 5, 2010 11:03:19 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to RESUMING>
<Oct 5, 2010 11:03:19 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default[1]" is now listening on 127.0.0.1:7101 for protocols iiop, t3, ldap, snmp, http.>
<Oct 5, 2010 11:03:19 AM EDT> <Notice> <Server> <BEA-002613> <Channel "Default" is now listening on 192.168.2.6:7101 for protocols iiop, t3, ldap, snmp, http.>
<Oct 5, 2010 11:03:19 AM EDT> <Notice> <WebLogicServer> <BEA-000331> <Started WebLogic Admin Server "DefaultServer" for domain "DefaultDomain" running in Development Mode>
<Oct 5, 2010 11:03:19 AM EDT> <Notice> <WebLogicServer> <BEA-000365> <Server state changed to RUNNING>
<Oct 5, 2010 11:03:19 AM EDT> <Notice> <WebLogicServer> <BEA-000360> <Server started in RUNNING mode>
2) And here's the feedback from testing the application server connection
Testing JSR-160 Runtime ... failed.
Cannot establish connection.
Testing JSR-160 DomainRuntime ... skipped.
Testing JSR-88 ... skipped.
Testing JSR-88-LOCAL ... skipped.
Testing JNDI ... skipped.
Testing JSR-160 Edit ... skipped.
Testing HTTP ... success.
Testing Server MBeans Model ... skipped.
1 of 8 tests successful.
3) The install of the webcenter extension was done via the JDEV Help - Check for updates
selecting for files
oracle.webcenter.framework_bundle.zip
and
oracle.webcenter.customization_bundle.zip
that were automatically installed by JDEV without any prompts for additional steps.

Pix 506e firewall configring for mail( Exhange), Web, FTP server

Similar Messages

Maybe you are looking for