PIX 515e VPN Host Connectivity Problem
I am having an issue with a VPN connection that I have.. I have a VPN set up to allow all hosts in a /24 subnet to work across from a single host on my side. From the host on my side, I am able to ping to and access some of the hosts on the other side. I have however, one host that is not allowing me to ping to it. We have verified firewall on the far end is allowing all but I can't make any kind of connection. We have verified that the machine on the far end is pingable and accessible from other networks. It is almost like the host on my side doesn't even try to connect across the tunnel. I have verified in my logs that when I do a ping from my host, it shows it building and tearing down a connection on the firewall for NAT so I know that traffic is at least getting to the firewall but it looks like it is not getting any farther. Has anyone seen any strange behavior like this before? I know that ACLs and such are correct on both ends due to the tunnel coming up when I try to access another host. The tunnel doesn't come up though when I try to ping the problem machine.
Thanks,
Brandon
Also, we have tested from the far end of the tunnel and when I attemp a ping to the problem machine, they don't see any traffic hitting thier VPN endpoint. They do however see traffic to all the other hosts that I attemp to access on thier network.
Similar Messages
-
I currently have a pix 515e setup as a firewall and vpn terminator. We will be moving our network to a new isp that will provide the firewall service, but i need to keep the pix for the vpn functionality. The pix currently has a public IP for the vpn but the new ISP want to do nat for the pix, so I have to give it a private ip. here is what the ISP sent me.
>Essentially - Customer needs
>1. Internal Server IP address that >will arrive from customer to the f/w.
>
>2. The public address NAT that will >represent the customer internal server.
>
>3. The proper ports open to support >this request. UDP ? 10000 or 4500 ? >and 500.
I'm new to VPN I would like some direction on where to find some documents on how to setup the cisco behind another router and without a public ip. Also can the pix have both interfaces on the same subnet?
Thank you
reneRene -
You can't have both the interfaces on the same subnet.
3. Ports needed for VPN to work.
UDP - 500 ==> which is ISAKMP
UDP - 4500 ==> NAT-T
UDP - 10000 ===> IPSec over UDP
ESP protocol ==> which is protocol number 50.
1 & 2. Your external (outside) IP address of the PIX.
Does this answer your question. -
Help needed to connect to remote PPTP VPN via PIX 515e
Hello,
A user in our office needs to connect to a client's remote PPTP VPN but can't connect. The user is running Windows 7. We have a Cisco PIX 515e firewall that is running PIX Version 6.3(3) - this is what our user is having to go through to try and make the connection to the client's remote VPN.
The client's network guys have come back and said the issue is at our side. They say that they can see some of our traffic but not all of it. The standard error is shown below, and they say it's symptomatic of the client-side firewall not allowing PPTP traffic:
"A connection between the VPN server and the VPN client XXX.XXX.XXX.XXX has been established, but the VPN connection cannot be completed. The most common cause for this is that a firewall or router between the VPN server and the VPN client is not configured to allow Generic Routing Encapsulation (GRE) packets (protocol 47). Verify that the firewalls and routers between your VPN server and the Internet allow GRE packets. Make sure the firewalls and routers on the user's network are also configured to allow GRE packets. If the problem persists, have the user contact the Internet service provider (ISP) to determine whether the ISP might be blocking GRE packets."
I have very little firewall experience and absolutely no Cisco experience I'm afraid. From looking at the PIX config I can see the following line:
fixup protocol pptp 1723.
Does this mean that the PPTP protcol is enabled on our firewall? Is this for both incoming and outgoing traffic?
I can see no reference to GRE 47 in the PIX config. Can anyone advise me what I should look for to see if this has been enabled or not?
I apologise again for my lack of knowledge. Any help or advice would be very gratefully received.
RosHi Eugene,
Thank you for taking the time to reply to me. Please see our full PIX config below. I've XX'd out names and IP addresses as I'm never comfortable posting those type of details in a public forum. I hope that the information below is still sufficient for you.
Thanks again for your help,
Ros
PIX(config)# en
Not enough arguments.
Usage: enable password [] [level ] [encrypted]
no enable password level
show enable
PIX(config)# show config
: Saved
: Written by enable_15 at 10:30:31.976 GMT/BDT Mon Apr 4 2011
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 auto
interface ethernet2 auto
nameif ethernet0 outside security0
nameif ethernet1 inside security100
nameif ethernet2 DMZ security10
enable password XXX encrypted
passwd XXX encrypted
hostname PIX
domain-name XXX.com
clock timezone GMT/BST 0
clock summer-time GMT/BDT recurring last Sun Mar 1:00 last Sun Oct 2:00
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol pptp 1723
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name XX.XX.XX.XX Secondary
access-list outside_access_in permit tcp XX.XX.XX.XX 255.255.255.240 host XX.XX.XX.XX eq smtp
access-list outside_access_in permit tcp any host XX.XX.XX.XX. eq https
access-list outside_access_in permit tcp any host XX.XX.XX.XX. eq 993
access-list outside_access_in permit tcp any host XX.XX.XX.XX. eq 587
access-list outside_access_in permit tcp any host XX.XX.XX.XX. eq 82
access-list outside_access_in permit tcp any host XX.XX.XX.XX. eq www
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq www
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq www
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq https
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq 993
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq 587
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq 82
access-list outside_access_in permit tcp host XX.XX.XX.XX host XX.XX.XX.XX eq 82
access-list outside_access_in permit tcp host XX.XX.XX.XX host XX.XX.XX.XX eq 82
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq smtp
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq 8082
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq www
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq https
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq 993
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq 587
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq 82
access-list outside_access_in permit tcp any host XX.XX.XX.XX eq smtp
access-list outside_access_in permit tcp any host XX.XX.XX.XX. eq www
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.0.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl deny udp any any eq 135
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list inside_outbound_nat0_acl permit ip any XX.XX.XX.XX 255.255.255.0
access-list outside_cryptomap_40 permit ip any XX.XX.XX.XX 255.255.255.0
access-list outside_cryptomap_60 permit ip any XX.XX.XX.XX 255.255.255.0
access-list USER1 permit ip any XX.XX.XX.XX 255.255.255.0
access-list outside_cryptomap_10 permit ip any XX.XX.XX.XX 255.255.255.0
access-list outside_cryptomap_20 permit ip any XX.XX.XX.XX 255.255.255.0
access-list outside_cryptomap_30 permit ip any XX.XX.XX.XX 255.255.255.0
access-list outside_cryptomap_50 permit ip any XX.XX.XX.XX 255.255.255.0
access-list outside_cryptomap_70 permit ip any XX.XX.XX.XX 255.255.0.0
access-list USER2 permit ip any XX.XX.XX.XX 255.255.255.0
access-list USER3 permit ip any XX.XX.XX.XX 255.255.255.0
access-list USER4 permit ip any XX.XX.XX.XX 255.255.0.0
pager lines 24
logging on
logging host inside XX.XX.XX.XX
icmp permit any outside
icmp permit any inside
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
ip address outside XX.XX.XX.XX 255.255.255.248
ip address inside XX.XX.XX.XX 255.255.255.0
no ip address DMZ
ip audit info action alarm
ip audit attack action alarm
pdm location XX.XX.XX.XX 255.255.255.255 inside
pdm location XX.XX.XX.XX 255.255.0.0 outside
pdm location XX.XX.XX.XX 255.255.255.0 outside
pdm logging debugging 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) XX.XX.XX.XX XX.XX.XX.XX netmask 255.255.255.255 0 0
static (inside,outside) XX.XX.XX.XX. XX.XX.XX.XX netmask 255.255.255.255 0 0
static (inside,outside) XX.XX.XX.XX. XX.XX.XX.XX netmask 255.255.255.255 0 0
static (inside,outside) XX.XX.XX.XX XX.XX.XX.XX netmask 255.255.255.255 0 0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 XX.XX.XX.XX 1
route inside XX.XX.XX.XX 255.255.0.0 XX.XX.XX.XX 1
timeout xlate 3:00:00
timeout conn 2:00:00 half-closed 0:30:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
ntp authenticate
ntp server XX.XX.XX.XX source outside prefer
http server enable
http XX.XX.XX.XX 255.255.0.0 outside
http XX.XX.XX.XX 255.255.255.0 outside
http XX.XX.XX.XX 255.255.255.255 inside
snmp-server host inside XX.XX.XX.XX
no snmp-server location
no snmp-server contact
snmp-server community XXX
snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map cola 20 set transform-set ESP-3DES-MD5
crypto dynamic-map dod 10 set transform-set ESP-3DES-MD5
crypto map outside_map 10 ipsec-isakmp dynamic cola
crypto map outside_map 20 ipsec-isakmp
crypto map outside_map 20 match address outside_cryptomap_20
crypto map outside_map 20 set peer XX.XX.XX.XX
crypto map outside_map 20 set transform-set ESP-3DES-MD5
crypto map outside_map 25 ipsec-isakmp
crypto map outside_map 25 match address USER1
crypto map outside_map 25 set peer XX.XX.XX.XX
crypto map outside_map 25 set transform-set ESP-3DES-MD5
crypto map outside_map 30 ipsec-isakmp
crypto map outside_map 30 match address outside_cryptomap_30
crypto map outside_map 30 set peer XX.XX.XX.XX
crypto map outside_map 30 set transform-set ESP-3DES-MD5
crypto map outside_map 40 ipsec-isakmp
crypto map outside_map 40 match address outside_cryptomap_40
crypto map outside_map 40 set peer XX.XX.XX.XX
crypto map outside_map 40 set transform-set ESP-3DES-MD5
crypto map outside_map 50 ipsec-isakmp
crypto map outside_map 50 match address outside_cryptomap_50
crypto map outside_map 50 set peer XX.XX.XX.XX
crypto map outside_map 50 set transform-set ESP-3DES-MD5
crypto map outside_map 60 ipsec-isakmp
crypto map outside_map 60 match address outside_cryptomap_60
crypto map outside_map 60 set peer XX.XX.XX.XX
crypto map outside_map 60 set transform-set ESP-3DES-MD5
crypto map outside_map 70 ipsec-isakmp
crypto map outside_map 70 match address outside_cryptomap_70
crypto map outside_map 70 set peer XX.XX.XX.XX
crypto map outside_map 70 set transform-set ESP-3DES-MD5
crypto map outside_map 75 ipsec-isakmp
crypto map outside_map 75 match address USER4
crypto map outside_map 75 set peer XX.XX.XX.XX
crypto map outside_map 75 set transform-set ESP-3DES-MD5
crypto map outside_map 80 ipsec-isakmp
crypto map outside_map 80 match address USER2
crypto map outside_map 80 set peer XX.XX.XX.XX
crypto map outside_map 80 set transform-set ESP-3DES-MD5
crypto map outside_map 90 ipsec-isakmp
crypto map outside_map 90 match address USER3
crypto map outside_map 90 set peer XX.XX.XX.XX
crypto map outside_map 90 set transform-set ESP-3DES-MD5
crypto map outside_map interface outside
isakmp enable outside
isakmp key ******** address XX.XX.XX.XX netmask 255.255.255.255 no-xauth no-config-mode
isakmp key ******** address 0.0.0.0 netmask 0.0.0.0
isakmp key ******** address XX.XX.XX.XX netmask 255.255.255.255 no-xauth no-config-mode
isakmp key ******** address XX.XX.XX.XX netmask 255.255.255.255 no-xauth no-config-mode
isakmp key ******** address XX.XX.XX.XX netmask 255.255.255.255 no-xauth no-config-mode
isakmp key ******** address XX.XX.XX.XX netmask 255.255.255.255 no-xauth no-config-mode
isakmp key ******** address XX.XX.XX.XX netmask 255.255.255.255 no-xauth no-config-mode
isakmp key ******** address XX.XX.XX.XX netmask 255.255.255.255 no-xauth no-config-mode
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
telnet XX.XX.XX.XX 255.255.0.0 outside
telnet XX.XX.XX.XX 255.255.255.255 inside
telnet XX.XX.XX.XX 255.255.255.255 inside
telnet XX.XX.XX.XX 255.255.255.255 inside
telnet timeout 30
ssh XX.XX.XX.XX 255.255.255.248 outside
ssh XX.XX.XX.XX 255.255.255.248 outside
ssh timeout 30
management-access inside
console timeout 0
terminal width 80
Cryptochecksum:XXX
PIX(config)# -
Can't Connect to Pix 501 VPN on Network
Hi All,
I have a software VPN client that connects just fine to the PIX 501 VPN, but I cannot ping or telnet to any services on the LAN. Below is my config and results of show cry ipsec sa. I would appreciate any suggestions to fix this.
It's been a while since I have done this. When I check the DHCP address received from the VPN, the default gateway is missing. IIRC, that is normal. What is strange is that when I ping, Windows does not show any sent packets.
Thanks,
--Drichards38
PIX Version 6.3(3)
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password bgVy005CZTsaMOwR encrypted
passwd bgVy005CZTsaMOwR encrypted
hostname cisco
domain-name xxxxxx.biz
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol ftp 1024-2048
fixup protocol ftp 49152-65534
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
access-list acl-out permit tcp any interface outside eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq telnet
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 60990
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq echo
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any interface inside eq www
access-list acl_out permit tcp any interface inside eq ftp
access-list acl_out permit tcp any interface inside eq 3389
access-list acl_out permit tcp any interface inside eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq 902
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list acl_out permit tcp any host aa.bb.cc.dd eq www
access-list acl_out permit tcp any host aa.bb.cc.dd eq https
access-list acl_out permit tcp any host aa.bb.cc.dd eq ftp
access-list acl_out permit tcp any host aa.bb.cc.dd eq 3389
access-list outside_cryptomap_dyn_20 permit ip any 10.0.0.0 255.0.0.0
access-list split_tunnel_acl permit ip 10.0.0.0 255.0.0.0 any
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside aa.bb.cc.dd 255.255.255.240
ip address inside 192.168.93.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool low_vpn_pool 10.0.1.205-10.0.1.210
pdm location 172.16.0.0 255.255.0.0 inside
pdm logging informational 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 1 192.168.93.0 255.255.255.0 0 0
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.67 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.68 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.69 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.70 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.71 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.72 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.73 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.74 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.75 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.76 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.77 netmask 255.255.255.255 0 0
static (inside,outside) aa.bb.cc.dd 192.168.93.78 netmask 255.255.255.255 0 0
access-group acl_out in interface outside
rip inside default version 1
route outside 0.0.0.0 0.0.0.0 aa.bb.cc.dd 1
timeout xlate 0:05:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
aaa authorization command LOCAL
http server enable
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto dynamic-map outside_dyn_map 20 match address outside_cryptomap_dyn_20
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map client authentication LOCAL
crypto map outside_map interface outside
isakmp enable outside
isakmp nat-traversal 20
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
vpngroup MY_VPN address-pool low_vpn_pool
vpngroup MY_VPN dns-server 4.2.2.1
vpngroup MY_VPN default-domain xxxxx.biz
vpngroup MY_VPN split-tunnel split_tunnel_acl
vpngroup MY_VPN idle-time 1800
vpngroup MY_VPN password ********
telnet 0.0.0.0 255.255.255.255 outside
telnet 192.168.93.0 255.255.255.0 inside
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh timeout 60
console timeout 0
dhcpd address 192.168.93.230-192.168.93.240 inside
dhcpd dns ff.gg.hh.ii ff.gg.hh.ii
dhcpd lease 65536
dhcpd ping_timeout 750
dhcpd domain xxxxxx.biz
dhcpd auto_config outside
dhcpd enable inside
username xxxx password xxxxxxx encrypted privilege 15
cisco(config)# show cry ipsec sa
interface: outside
Crypto map tag: outside_map, local addr. aa.bb.cc.dd
local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
remote ident (addr/mask/prot/port): (10.0.1.205/255.255.255.255/0/0)
current_peer: jj.kk.ll.mm:1265
dynamic allocated peer ip: 10.0.1.205
PERMIT, flags={transport_parent,}
#pkts encaps: 0, #pkts encrypt: 0, #pkts digest 0
#pkts decaps: 38, #pkts decrypt: 38, #pkts verify 38
#pkts compressed: 0, #pkts decompressed: 0
#pkts not compressed: 0, #pkts compr. failed: 0, #pkts decompress failed: 0
#send errors 0, #recv errors 0
local crypto endpt.: aa.bb.cc.dd, remote crypto endpt.: 97.93.95.133
path mtu 1500, ipsec overhead 64, media mtu 1500
current outbound spi: 3a898e67
inbound esp sas:
spi: 0xeeb64931(4004923697)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel UDP-Encaps, }
slot: 0, conn id: 1, crypto map: outside_map
sa timing: remaining key lifetime (k/sec): (4607993/28610)
IV size: 8 bytes
replay detection support: Y
inbound ah sas:
inbound pcp sas:
outbound esp sas:
spi: 0x3a898e67(982093415)
transform: esp-3des esp-md5-hmac ,
in use settings ={Tunnel UDP-Encaps, }
slot: 0, conn id: 2, crypto map: outside_map
sa timing: remaining key lifetime (k/sec): (4608000/28574)
IV size: 8 bytes
replay detection support: Y
outbound ah sas:
outbound pcp sas:I just set the logging to high on all areas of the Cisco VPN client. Below is the resulting log. Everything looks ok from here:
Cisco Systems VPN Client Version 5.0.03.0530
Copyright (C) 1998-2007 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 5.1.2600 Service Pack 3
29 09:57:02.887 09/03/12 Sev=Info/4 CM/0x63100002
Begin connection process
30 09:57:02.897 09/03/12 Sev=Info/4 CM/0x63100004
Establish secure connection
31 09:57:02.897 09/03/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "a.b.c.d"
32 09:57:02.907 09/03/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with a.b.c.d.
33 09:57:02.917 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to a.b.c.d
34 09:57:03.228 09/03/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
35 09:57:03.228 09/03/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
36 09:57:03.228 09/03/12 Sev=Info/6 IPSEC/0x6370002C
Sent 47 packets, 0 were fragmented.
37 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
38 09:57:03.979 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, VID(Xauth), VID(dpd), VID(Unity), VID(?), KE, ID, NON, VID(?), VID(Nat-T), NAT-D, NAT-D, HASH) from a.b.c.d
39 09:57:04.039 09/03/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
40 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
41 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
42 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
43 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000082
Received IOS Vendor ID with unknown capabilities flag 0x000000A5
44 09:57:03.979 09/03/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
45 09:57:03.999 09/03/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
46 09:57:03.999 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to a.b.c.d
47 09:57:03.999 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
48 09:57:03.999 09/03/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0x0421, Remote Port = 0x1194
49 09:57:03.999 09/03/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
50 09:57:03.999 09/03/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
51 09:57:04.029 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
52 09:57:04.029 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_INITIAL_CONTACT) from a.b.c.d
53 09:57:04.029 09/03/12 Sev=Warning/2 IKE/0xA3000067
Received Unexpected InitialContact Notify (PLMgrNotify:886)
54 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
55 09:57:04.039 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from a.b.c.d
56 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
57 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 2 seconds, setting expiry to 86398 seconds from now
58 09:57:04.039 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
59 09:57:04.039 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
60 09:57:04.039 09/03/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
61 09:57:09.327 09/03/12 Sev=Info/4 CM/0x63100017
xAuth application returned
62 09:57:09.327 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
63 09:57:09.367 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
64 09:57:09.367 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
65 09:57:09.367 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
66 09:57:09.367 09/03/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
67 09:57:09.387 09/03/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
68 09:57:09.387 09/03/12 Sev=Info/5 IKE/0x6300005D
Firewall Policy: Product=Cisco Systems Integrated Client Firewall, Capability= (Centralized Protection Policy).
69 09:57:09.387 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to a.b.c.d
70 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
71 09:57:09.427 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from a.b.c.d
72 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 10.0.1.205
73 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 4.2.2.1
74 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = xxxx.biz
75 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
76 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 10.0.0.0
mask = 255.0.0.0
protocol = 0
src port = 0
dest port=0
77 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
78 09:57:09.427 09/03/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
79 09:57:09.427 09/03/12 Sev=Info/4 CM/0x63100019
Mode Config data received
80 09:57:09.427 09/03/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 10.0.1.205, GW IP = a.b.c.d, Remote IP = 0.0.0.0
81 09:57:09.437 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to a.b.c.d
82 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
83 09:57:09.477 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from a.b.c.d
84 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
85 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000046
RESPONDER-LIFETIME notify has value of 4608000 kb
86 09:57:09.477 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to a.b.c.d
87 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=D70550E6 OUTBOUND SPI = 0xB335C6DA INBOUND SPI = 0xE99E1A59)
88 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xB335C6DA
89 09:57:09.477 09/03/12 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0xE99E1A59
90 09:57:09.527 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 172.16.0.11 0.0.0.0 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
91 09:57:10.448 09/03/12 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=10.0.1.205/255.0.0.0
DNS=4.2.2.1,0.0.0.0
WINS=0.0.0.0,0.0.0.0
Domain=xxxx.biz
Split DNS Names=
92 09:57:10.458 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
10.0.0.0 255.0.0.0 10.0.1.205 10.0.1.205 25
10.0.1.205 255.255.255.255 127.0.0.1 127.0.0.1 25
10.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 25
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 10.0.1.205 10.0.1.205 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 10.0.1.205 0.0.0.0 1
255.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
93 09:57:10.458 09/03/12 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
94 09:57:10.458 09/03/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 172.16.0.1 172.16.0.11 25
10.0.0.0 255.0.0.0 10.0.1.205 10.0.1.205 1
10.0.1.205 255.255.255.255 127.0.0.1 127.0.0.1 25
10.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 25
a.b.c.d 255.255.255.255 172.16.0.1 172.16.0.11 1
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1
172.16.0.0 255.255.0.0 172.16.0.11 172.16.0.11 25
172.16.0.1 255.255.255.255 172.16.0.11 172.16.0.11 1
172.16.0.11 255.255.255.255 127.0.0.1 127.0.0.1 25
172.16.255.255 255.255.255.255 172.16.0.11 172.16.0.11 25
224.0.0.0 240.0.0.0 10.0.1.205 10.0.1.205 25
224.0.0.0 240.0.0.0 172.16.0.11 172.16.0.11 25
255.255.255.255 255.255.255.255 10.0.1.205 0.0.0.0 1
255.255.255.255 255.255.255.255 10.0.1.205 10.0.1.205 1
255.255.255.255 255.255.255.255 172.16.0.11 172.16.0.11 1
95 09:57:10.458 09/03/12 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
96 09:57:10.508 09/03/12 Sev=Info/4 CM/0x6310001A
One secure connection established
97 09:57:10.618 09/03/12 Sev=Info/4 CM/0x6310003B
Address watch added for 172.16.0.11. Current hostname: toughone, Current address(es): 10.0.1.205, 172.16.0.11.
98 09:57:10.638 09/03/12 Sev=Info/4 CM/0x6310003B
Address watch added for 10.0.1.205. Current hostname: toughone, Current address(es): 10.0.1.205, 172.16.0.11.
99 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
100 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
101 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xdac635b3 into key list
102 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
103 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x591a9ee9 into key list
104 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 10.0.1.205
105 09:57:10.638 09/03/12 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 172.16.0.11. SG: a.b.c.d
106 09:57:10.638 09/03/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
107 09:57:19.741 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
108 09:57:19.741 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445672
109 09:57:19.772 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
110 09:57:19.772 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
111 09:57:19.772 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445672, seq# expected = 3951445672
112 09:57:30.257 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
113 09:57:30.257 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445673
114 09:57:30.297 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
115 09:57:30.297 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
116 09:57:30.297 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445673, seq# expected = 3951445673
117 09:57:40.772 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
118 09:57:40.772 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445674
119 09:57:40.802 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
120 09:57:40.802 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
121 09:57:40.802 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445674, seq# expected = 3951445674
122 09:57:54.291 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
123 09:58:04.306 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
124 09:58:14.320 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
125 09:58:24.334 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
126 09:58:34.349 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
127 09:58:41.359 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
128 09:58:41.359 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445675
129 09:58:41.389 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
130 09:58:41.389 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
131 09:58:41.389 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445675, seq# expected = 3951445675
132 09:58:54.378 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
133 09:59:04.392 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
134 09:59:14.406 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
135 09:59:24.421 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
136 09:59:34.435 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
137 09:59:41.946 09/03/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to a.b.c.d
138 09:59:41.946 09/03/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to a.b.c.d, our seq# = 3951445676
139 09:59:41.976 09/03/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = a.b.c.d
140 09:59:41.976 09/03/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from a.b.c.d
141 09:59:41.976 09/03/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from a.b.c.d, seq# received = 3951445676, seq# expected = 3951445676
142 09:59:54.464 09/03/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA -
RV0xx connecting to PIX (515e) via ipsec
We have fielded aproximatly 40 previous revisoin rv042/rv082 routers running 1.3.12.19-tm firmware.
We have recently begun reciveing v3 hardware running firmware 4.0.0.7.
The previous routers connected with out complication to our existing PIX 515e 8.0(3) Router using ipsec vpn connections.
The new version routers congiured with seemingly identical settings fail to connect ant throw the following errors in syslog on the rv042:
protocol/port in Phase 1 ID Payload must be 0/0 or 17/500 but are 17/0
The PIX syslog throws:
Received an un-encrypted INVALID_ID_INFO notify message, dropping
The two configurations never connect.
Any suggestions would be appreciated.Hi !
The reason this does not work is that you loose connection with the terminal server the second the VPN client is operativ. The VPN client is denied local access and therefore the connection between the internet user and the terminal server is disconnected.. When this happens you should not be able to do any work on the terminal server until the client is dosconnected.
I use the same solution in my work (great for testing when installing VPN for customers). What I have done is this:
1. On the Terminal server install VMWare or Microsoft Virtual PC.
2. Install windows xp on as a virtual pc
3. Start the virtual windows xp and install the VPN client
4. Use the virtual windows xp and client when doing connections...
This works great !!
The reason this works, is that you no longer connect to the pc doing the actual VPN connection, but to a terminal showing the monitor of the client.
Best of luck !!
Jorgen Lanesskog
Ementor, Norway -
RemoteApp with host connected to VPN
Hi,
I have a question regarding RemoteApp vs regular Remote Desktop Connection spiced with a VPN connection initiated from the host.
We're in the process of moving from PCs to thin clients and we have set up an RDS farm (all servers are Windows Server 2012 R2, they are all in the same domain and same LAN) as follows:
1 x RD Connection Broker + RD Licensing + RD Web Access
3 x RD Session Host
The users/clients will connect with regular remote desktop connection software (no Citrix or anything). Two of the RD SHs will be providing the users access to their normal applications, but some users also need to use remote resources which are only available
via VPN connection, hence the third RD SH. (Currently it is solved by every user having a virtual machine on their PCs and connecting to the VPN from there.) We can't put the VPN connection to the two "regular" RD SHs, because we'll need more VPN
connections later. The idea was to install and set up the VPN on the third host and publish the needed apps by RemoteApp to the users who use it.
The problem:
Once the host connects to the VPN the users are unable to launch the RemoteApp applications. If it's not connected then they can start them. The VPN client is a Cisco AnyConnect Secure Mobility Client that can only connect if the connection is initiated
by a local user and no other user is currenty logged on (it's a remote side policy we can't change). If the users connect to the RD host with a regular remote desktop connection after the VPN is set up then it works as expected, they can launch the apps and
work with them.
The question:
What is the difference between launching a RemoteApp and connecting to the RD host via RDP? How can I debug this RemoteApp connection problem?
Please ask if something is not clear!
Thank you!
PS: If I'm not heading into the right direction and someone has a better idea, I'd be grateful to hear (read) it!Hello Vargabes7,
You can configure a server that allows remote users to access resources on your private network over dial-up or virtual private network (VPN) connections. This type of server is called a remote access/VPN server. Remote access/VPN servers can also provide
network address translation (NAT). With NAT, the computers on your private network can share a single connection to the Internet. With VPN and NAT, your VPN clients can determine the IP addresses of the computers on your private network, but other computers
on the Internet cannot.
Before you configure your server as a remote access/VPN server, you should verify whether or not:
The operating system is configured correctly.
Your server is correctly configured for optimal security for your network needs. Because your remote access/VPN server will connect your private network, the Internet, and your remote clients, you must make sure the server is secure. The security
of your private network depends on the security of your remote access/VPN server. For more information, see
Security information for remote access.
This computer has two network interfaces, one that connects to the Internet and one that connects to the private network. The connection to the Internet must be a dedicated connection with enough bandwidth that VPN users can connect to your private network
and users on your private network can connect to the Internet. The connection to computers on your private network must be made through a hardware device, such as a network adapter.
All needed network protocols have been installed for your network interfaces. For more information, see
Network interfaces.
Windows Firewall is disabled on the server that you want to configure for remote access/VPN. You will configure the Basic Firewall feature of Routing and Remote Access during setup, which will serve in place of Windows Firewall.
Internet Connection Sharing is disabled on the server that you want to configure for remote access/VPN.
The Security Configuration Wizard is installed and enabled.
To configure a remote access/VPN server, start the Configure Your Server Wizard by doing either of the following:
From Manage Your Server, click Add or remove a role. By default, Manage Your Server starts automatically when you log on.
To open the Configure Your Server Wizard, click Start, click
Control Panel, double-click Administrative Tools, and then double-click
Configure Your Server Wizard.
On the Configuration Options page, click Custom configuration and click
Next. On the Server Role page, click Remote access/VPN server, and then click
Next.
Best regards,
Sophia Sun
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread. -
Cisco PIX 515E multiple ISP support in a VPN scenario
Iam currently running a cisco 7.2 ios in a Cisco PIX 515E appliance. I have terminated two ISP links in the two ports, and I also have a inside network (LAN). I want to establish 2 Site-Site VPN tunnels using each one of these ISP links respectively (Site 1 in ISP link 1 && Site 2 in ISP link 2).
Is this possible to achieve??Hello,
This should work. Route the remote endpoint for site 1 out link 1 (using a static route) and for site 2 out link 2 (using a static route) and that should do it.
Return traffic should work, assuming both ISPs aren't advertising the networks your interfaces are on via BGP (ie, you don't want return traffic from site one coming down the link to site 2 because that ISP is advertising that AS as well.)
--Jason -
I have an apple TC at home, running firmware version 7.6.1, and I can't connect to a VPN server at my work through the TC wifi. If I connect my macbook directly to my modem with an ethernet cable, I can connect without difficulties. When attempting to connect through the TC wifi, the VPN status indicator says that I connect and authenticate, but when I attemp to access a secured, internal website or computer at my work nothing connects.
Any suggestions? Happy to provide more info on my setup and devices if you need it.
Thanks for your help.mwjaeger wrote:
I turned off 'Back to my Mac' after reading an article about it using ports soemtimes used for VPN connection but it didn't seem to help.
Turning off BTMM does not change the port allocation in the TC.. that is where the problem is.
Can you be more specific about the ports required for my VPN? The setup in my network connections on the MPBP points to my work website and everything else (except for my my password) seems to be automatic without mentioning any specific port numbers. If I did find the required port number from the tech support guys at work, how exactly do I set them on my MBP.
This setup again has nothing to do with the MBP.. it is the router where the issue is.. as clearly your initial experiment connecting directly to the modem shows.. it is open ports on the router that you need to do.
I cannot tell you which ports without knowing what vpn client you are using. That is why my previous post began.. what vpn and what client??? Perhaps I should put it in bold.. WHAT VPN CLIENT DO YOU USE?
Is it a built in client in Mac OS.. or is it a Cisco client or some other brand software client.. tell me that.. and I can probably figure out the ports.
The vpn client should also have a log.. that will likely have useful information about why the VPN cannot connect.
Also, I have an old linksys router. How do I connect this into my setup if I put the TC into bridge mode?
Connect the Linksys up to the modem in router mode.. bridge the TC. The Linksys will now be the main router and handle the connection. The TC becomes a dumb WAP and switch plus network hard disk.
Will all my devices setup to run from and back-up to the TC still work?
Yes, the network will still function as it did. You do not need to change the TC wireless or other settings.. just bridge instead of main router.
Look in the Linksys for VPN pass-through. Some have it set automatically.. others require it checked.
If you run into issues.. I need the exact model number and firmware revision to work out how to fix vpn. -
Which ports to open in PIX for outgoing Cisco VPN client connections ?
I have Cisco vpn clients behind the PIX and i want them to connect to a vpn 3005 which i behind another PIX . Can anybody tell me which ports i have to open on both the PIX firewalls ?
It depends on how you have deployed your VPN Remote Access users.
By default, if you enable IPSec-Over-TCP or IPSec-over-UDP, then port 10000 is used for both, these methods are Cisco Proprietary and can be changed.
If you use NAT-T (NAT Traversal), the Standards-based implementation, then it uses UDP-4500).
either way, the operation of the VPN depends on:
1) Whether these service have been enable on the VPN Concentrator
2) Enabling the relevant transport settings on the VPN Client connection Properties.
Regarding the PIX infront of the VPNC3005, you will need to allow these above ports inbound to your VPNC3005 Public interface.
Locally, it depends if you filter outbound connections through your PIX. If you don't, then the PIX will allow the connection for the VPN Client attempting to access the remote VPNC3005 -
Out of ideas diagnosing VPN connection problems
I'm having trouble narrowing down what's causing the VPN connection problems to my new Mini Server. Sometimes I can connect just fine with my MacBookPro and use all the resources like file sharing, etc. So, this leads me to believe it has been setup correctly. But then, for no reason at all (maybe it's later in the same day, or a completely different day) it will just stop working and I cannot connect at all.
*MacBook and iMac at home cannot connect, but iPhone can*
This is what's really throwing me off. This afternoon, I cannot connect to the server from home with my MacBook or my iMac. BUT, my iPhone can -using the same WiFi network my computers are on, not the cellular network. How could that be? The VPN settings on all 3 devices match exactly.
*Colleagues with other ISP's can connect, while I cannot*
I've called Comcast business (which provides the static IP for our office server) and they tell me all my settings are correct for allowing VPN traffic through. Likewise, Comcast Residential tells me there is nothing that would block VPN traffic from my home. They tell me to talk with Apple. argh!
*Web and Server Admin services are still accessible when VPN is not working*
We have exposed the Server's Web and Admin services without needing a VPN connection to access them. Since these services are accessible to me even when the VPN is not working, this leads me to believe the server is operating normally and capable of receiving incoming traffic.
I'm out of ideas and I'm starting to lose my mind!!! Any ideas on why my 2 computers sometimes can connect, yet sometimes cannot...all the while, my iPhone can connect just fine over the same network???I don't have an explanation for the erratic nature of your connections. It's only as I've said before, in my experiences with such problems it has always traced back to misconfigured network or DNS settings. mDNS is multicast DNS and it's a protocol Apple uses so its devices can find each other easily. That may be the reason why your iPhone can connect when other things can't.
To take a step back, here is how I think things should be set up:
\- Your dedicated IP address should be assigned to your router automatically through PPPoE
\- The name servers as set in your router should be your ISP's name servers
\- Make sure the server has only one connection to the router that is managing the dedicated IP, either wired or wireless, but not both
\- A static network address should be assigned to your server's MAC address in the router's DHCP settings
\- The server's network address should be put in the DMZ on the router or set as the default server in the NAT settings, depending on the router
\- The network settings in System Preferences on the server should be set to DHCP with manual address and the server's network address entered correctly
\- The router address should be listed correctly in the network settings in System Preferences on the server
\- The name servers in the network settings in System Preferences on the server should be 127.0.0.1 and the router's IP address, nothing else.
\- The zone files on the server should have a primary and reverse zone for each domain name and its network address. Do not use the dedicated IP address in the zone files on the server.
If everything is set as I described, it should work. If it doesn't, it's time to call a witch doctor or an exorcist. -
VPN auto connect leads problem when accessing the private url in my app through HttpClient
Hi,
I have app to execute my WCF service through HttpClient(). I configured my SSL VPN in sonicwall mobile connect with auto connect option. So when accessing my internal WCF service, Wp 8.1 asks the VPN connection screen. If I follow the screen, VPN
has connected and return to my App. But here I received "An error has ocurred. While sending request to server" in Wp 8.1 screen. Even if I debug through visual studio I couldn't catch or track the actual error in code. Below the code I am using
for your reference. Kindly help me in this regard.
try
HttpClientHandler handler = new HttpClientHandler(); ;
handler.AllowAutoRedirect = false;
HttpClient httpClient = new HttpClient(handler);
httpClient.MaxResponseContentBufferSize = 256000;
HttpResponseMessage response = await httpClient.GetAsync("http://172.0.0.11/xxxxx/Service1.svc/xxxxCheck/" + usr.username + "/" + App.DeviceId + "/" + usr.password);
response.EnsureSuccessStatusCode();
string content = await response.Content.ReadAsStringAsync();
List<EmcUserResult> userres = JsonConvert.DeserializeObject<List<EmcUserResult>>(content);
if (userres.FirstOrDefault().Allowed == "TRUE")
NavigationService.Navigate(new Uri("/MainPage.xaml", UriKind.Relative)); // call MainPage
else
MessageBox.Show("This User was blocked. Contact admin.");
catch (Exception ex)
MessageBox.Show(ex.Message);I recommend that you check the network traffic by using either Wireshark or Fiddler to see what's going on with the request.
Matt Small - Microsoft Escalation Engineer - Forum Moderator
If my reply answers your question, please mark this post as answered.
NOTE: If I ask for code, please provide something that I can drop directly into a project and run (including XAML), or an actual application project. I'm trying to help a lot of people, so I don't have time to figure out weird snippets with undefined
objects and unknown namespaces. -
Webserver on DMZ cannot send email via php script using SMTP (cisco firewall pix 515e)
Hello,
I have two web servers that are sitting in a DMZ behind a Cisco Firewall PIX 515e. The webservers appear to be configured correctly as our website and FTP website are up. On two of our main website, we have two contact forms that use a simple html for to call a php script that uses smtp as its mailing protocol. Since, I am not the network administrator, I don't quite understand how to read the current configurations on the firewall, but I suspect that port 25 is blocked, which prevents the script from actually working or sending out emails. What I've done to narrow the problem done is the following: I used a wamp server to test our scripts with our smtp servers settings, was able to successfully send an email out to both my gmail and work place accounts. Currently, we have backupexec loaded on both of these servers, and when I try to send out an alert I never receive it. I think because port 25 is closed on both of those servers. I will be posting our configuration. if anyone can take a look and perhaps explain to me how I can change our webservers to communicate and successfully deliver mail via that script, I would gladly appreciate it. our IP range is 172.x.x.x, but it looks like our webservers are using 192.x.x.x with NAT in place. Please someone help.
Thanks,
Jeff Mateo
PIX Version 6.3(4)
interface ethernet0 100full
interface ethernet1 100full
interface ethernet2 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
nameif ethernet2 DMZ security50
enable password GFO9OSBnaXE.n8af encrypted
passwd GFO9OSBnaXE.n8af encrypted
hostname morrow-pix-ct
domain-name morrowco.com
clock timezone EST -5
clock summer-time EDT recurring
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
no fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name 12.42.47.27 LI-PIX
name 172.20.0.0 CT-NET
name 172.23.0.0 LI-NET
name 172.22.0.0 TX-NET
name 172.25.0.0 NY-NET
name 192.168.10.0 CT-DMZ-NET
name 1.1.1.1 DHEC_339849.ATI__LEC_HCS722567SN
name 1.1.1.2 DHEC_339946.ATI__LEC_HCS722632SN
name 199.191.128.105 web-dns-1
name 12.127.16.69 web-dns-2
name 12.3.125.178 NY-PIX
name 64.208.123.130 TX-PIX
name 24.38.31.80 CT-PIX
object-group network morrow-net
network-object 12.42.47.24 255.255.255.248
network-object NY-PIX 255.255.255.255
network-object 64.208.123.128 255.255.255.224
network-object 24.38.31.64 255.255.255.224
network-object 24.38.35.192 255.255.255.248
object-group service morrow-mgmt tcp
port-object eq 3389
port-object eq telnet
port-object eq ssh
object-group network web-dns
network-object web-dns-1 255.255.255.255
network-object web-dns-2 255.255.255.255
access-list out1 permit icmp any any echo-reply
access-list out1 permit icmp object-group morrow-net any
access-list out1 permit tcp any host 12.193.192.132 eq ssh
access-list out1 permit tcp any host CT-PIX eq ssh
access-list out1 permit tcp any host 24.38.31.72 eq smtp
access-list out1 permit tcp any host 24.38.31.72 eq https
access-list out1 permit tcp any host 24.38.31.72 eq www
access-list out1 permit tcp any host 24.38.31.70 eq www
access-list out1 permit tcp any host 24.38.31.93 eq www
access-list out1 permit tcp any host 24.38.31.93 eq https
access-list out1 permit tcp any host 24.38.31.93 eq smtp
access-list out1 permit tcp any host 24.38.31.93 eq ftp
access-list out1 permit tcp any host 24.38.31.93 eq domain
access-list out1 permit tcp any host 24.38.31.94 eq www
access-list out1 permit tcp any host 24.38.31.94 eq https
access-list out1 permit tcp any host 24.38.31.71 eq www
access-list out1 permit tcp any host 24.38.31.71 eq 8080
access-list out1 permit tcp any host 24.38.31.71 eq 8081
access-list out1 permit tcp any host 24.38.31.71 eq 8090
access-list out1 permit tcp any host 24.38.31.69 eq ssh
access-list out1 permit tcp any host 24.38.31.94 eq ftp
access-list out1 permit tcp any host 24.38.31.92 eq 8080
access-list out1 permit tcp any host 24.38.31.92 eq www
access-list out1 permit tcp any host 24.38.31.92 eq 8081
access-list out1 permit tcp any host 24.38.31.92 eq 8090
access-list out1 permit tcp any host 24.38.31.93 eq 3389
access-list out1 permit tcp any host 24.38.31.92 eq https
access-list out1 permit tcp any host 24.38.31.70 eq https
access-list out1 permit tcp any host 24.38.31.74 eq www
access-list out1 permit tcp any host 24.38.31.74 eq https
access-list out1 permit tcp any host 24.38.31.74 eq smtp
access-list out1 permit tcp any host 24.38.31.75 eq https
access-list out1 permit tcp any host 24.38.31.75 eq www
access-list out1 permit tcp any host 24.38.31.75 eq smtp
access-list out1 permit tcp any host 24.38.31.70 eq smtp
access-list out1 permit tcp any host 24.38.31.94 eq smtp
access-list dmz1 permit icmp any any echo-reply
access-list dmz1 deny ip any 10.0.0.0 255.0.0.0
access-list dmz1 deny ip any 172.16.0.0 255.240.0.0
access-list dmz1 deny ip any 192.168.0.0 255.255.0.0
access-list dmz1 permit ip any any
access-list dmz1 deny ip any any
access-list nat0 permit ip CT-NET 255.255.0.0 192.168.220.0 255.255.255.0
access-list nat0 permit ip host 172.20.8.2 host 172.23.0.2
access-list nat0 permit ip CT-NET 255.255.0.0 LI-NET 255.255.0.0
access-list nat0 permit ip CT-NET 255.255.0.0 NY-NET 255.255.0.0
access-list nat0 permit ip CT-NET 255.255.0.0 TX-NET 255.255.0.0
access-list vpn-split-tun permit ip CT-NET 255.255.0.0 192.168.220.0 255.255.255
.0
access-list vpn-split-tun permit ip CT-DMZ-NET 255.255.255.0 192.168.220.0 255.2
55.255.0
access-list vpn-dyn-match permit ip any 192.168.220.0 255.255.255.0
access-list vpn-ct-li-gre permit gre host 172.20.8.2 host 172.23.0.2
access-list vpn-ct-ny permit ip CT-NET 255.255.0.0 NY-NET 255.255.0.0
access-list vpn-ct-ny permit ip CT-DMZ-NET 255.255.255.0 NY-NET 255.255.0.0
access-list vpn-ct-tx permit ip CT-NET 255.255.0.0 TX-NET 255.255.0.0
access-list vpn-ct-tx permit ip CT-DMZ-NET 255.255.255.0 TX-NET 255.255.0.0
access-list static-dmz-to-ct-2 permit ip host 192.168.10.141 CT-NET 255.255.248.
0
access-list nat0-dmz permit ip CT-DMZ-NET 255.255.255.0 192.168.220.0 255.255.25
5.0
access-list nat0-dmz permit ip CT-DMZ-NET 255.255.255.0 LI-NET 255.255.0.0
access-list nat0-dmz permit ip CT-DMZ-NET 255.255.255.0 NY-NET 255.255.0.0
access-list nat0-dmz permit ip CT-DMZ-NET 255.255.255.0 TX-NET 255.255.0.0
access-list static-dmz-to-ct-1 permit ip host 192.168.10.140 CT-NET 255.255.248.
0
access-list static-dmz-to-li-1 permit ip CT-DMZ-NET 255.255.255.0 CT-NET 255.255
.248.0
access-list vpn-ct-li permit ip CT-NET 255.255.0.0 LI-NET 255.255.0.0
access-list vpn-ct-li permit ip CT-DMZ-NET 255.255.255.0 LI-NET 255.255.0.0
access-list vpn-ct-li permit ip host 10.10.2.2 host 10.10.1.1
access-list in1 permit tcp host 172.20.1.21 any eq smtp
access-list in1 permit tcp host 172.20.1.20 any eq smtp
access-list in1 deny tcp any any eq smtp
access-list in1 permit ip any any
access-list in1 permit tcp any any eq smtp
access-list cap4 permit ip host 172.20.1.82 host 192.168.220.201
access-list cap2 permit ip host 172.20.1.82 192.168.220.0 255.255.255.0
access-list in2 deny ip host 172.20.1.82 any
access-list in2 deny ip host 172.20.1.83 any
access-list in2 permit ip any any
pager lines 43
logging on
logging timestamp
logging buffered notifications
logging trap notifications
logging device-id hostname
logging host inside 172.20.1.22
mtu outside 1500
mtu inside 1500
mtu DMZ 1500
ip address outside CT-PIX 255.255.255.224
ip address inside 172.20.8.1 255.255.255.0
ip address DMZ 192.168.10.1 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool ctpool 192.168.220.100-192.168.220.200
ip local pool ct-thomson-pool-201 192.168.220.201 mask 255.255.255.255
pdm history enable
arp timeout 14400
global (outside) 1 24.38.31.81
nat (inside) 0 access-list nat0
nat (inside) 1 CT-NET 255.255.0.0 2000 10
nat (DMZ) 0 access-list nat0-dmz
static (inside,DMZ) CT-NET CT-NET netmask 255.255.0.0 0 0
static (inside,outside) 24.38.31.69 172.20.8.2 netmask 255.255.255.255 0 0
static (DMZ,outside) 24.38.31.94 192.168.10.141 netmask 255.255.255.255 0 0
static (inside,outside) 24.38.31.71 172.20.1.11 dns netmask 255.255.255.255 0 0
static (DMZ,outside) 24.38.31.93 192.168.10.140 netmask 255.255.255.255 0 0
static (DMZ,inside) 24.38.31.93 access-list static-dmz-to-ct-1 0 0
static (DMZ,inside) 24.38.31.94 access-list static-dmz-to-ct-2 0 0
static (inside,outside) 24.38.31.92 172.20.1.56 netmask 255.255.255.255 0 0
static (DMZ,outside) 24.38.31.91 192.168.10.138 netmask 255.255.255.255 0 0
static (DMZ,outside) 24.38.31.90 192.168.10.139 netmask 255.255.255.255 0 0
static (inside,outside) 24.38.31.72 172.20.1.20 netmask 255.255.255.255 0 0
static (inside,outside) 24.38.31.73 172.20.1.21 netmask 255.255.255.255 0 0
static (inside,outside) 24.38.31.70 172.20.1.91 netmask 255.255.255.255 0 0
static (DMZ,outside) 24.38.31.88 192.168.10.136 netmask 255.255.255.255 0 0
static (DMZ,outside) 24.38.31.89 192.168.10.137 netmask 255.255.255.255 0 0
static (inside,outside) 24.38.31.74 172.20.1.18 netmask 255.255.255.255 0 0
static (inside,outside) 24.38.31.75 172.20.1.92 netmask 255.255.255.255 0 0
access-group out1 in interface outside
access-group dmz1 in interface DMZ
route outside 0.0.0.0 0.0.0.0 24.38.31.65 1
route inside 10.10.2.2 255.255.255.255 172.20.8.2 1
route inside CT-NET 255.255.248.0 172.20.8.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server TACACS+ max-failed-attempts 3
aaa-server TACACS+ deadtime 10
aaa-server RADIUS protocol radius
aaa-server RADIUS max-failed-attempts 3
aaa-server RADIUS deadtime 10
aaa-server LOCAL protocol local
aaa-server ct-rad protocol radius
aaa-server ct-rad max-failed-attempts 2
aaa-server ct-rad deadtime 10
aaa-server ct-rad (inside) host 172.20.1.22 morrow123 timeout 7
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
aaa authentication serial console LOCAL
aaa authentication telnet console LOCAL
http server enable
http 173.220.252.56 255.255.255.248 outside
http 65.51.181.80 255.255.255.248 outside
http 208.65.108.176 255.255.255.240 outside
http CT-NET 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server community m0rroW(0
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
sysopt connection permit-pptp
crypto ipsec transform-set 3des-sha esp-3des esp-sha-hmac
crypto ipsec transform-set 3des-md5 esp-3des esp-md5-hmac
crypto dynamic-map dyn_map 20 match address vpn-dyn-match
crypto dynamic-map dyn_map 20 set transform-set 3des-sha
crypto map ct-crypto 10 ipsec-isakmp
crypto map ct-crypto 10 match address vpn-ct-li-gre
crypto map ct-crypto 10 set peer LI-PIX
crypto map ct-crypto 10 set transform-set 3des-sha
crypto map ct-crypto 15 ipsec-isakmp
crypto map ct-crypto 15 match address vpn-ct-li
crypto map ct-crypto 15 set peer LI-PIX
crypto map ct-crypto 15 set transform-set 3des-sha
crypto map ct-crypto 20 ipsec-isakmp
crypto map ct-crypto 20 match address vpn-ct-ny
crypto map ct-crypto 20 set peer NY-PIX
crypto map ct-crypto 20 set transform-set 3des-sha
crypto map ct-crypto 30 ipsec-isakmp
crypto map ct-crypto 30 match address vpn-ct-tx
crypto map ct-crypto 30 set peer TX-PIX
crypto map ct-crypto 30 set transform-set 3des-sha
crypto map ct-crypto 65535 ipsec-isakmp dynamic dyn_map
crypto map ct-crypto client authentication ct-rad
crypto map ct-crypto interface outside
isakmp enable outside
isakmp key ******** address LI-PIX netmask 255.255.255.255 no-xauth no-config-mo
de
isakmp key ******** address 216.138.83.138 netmask 255.255.255.255 no-xauth no-c
onfig-mode
isakmp key ******** address NY-PIX netmask 255.255.255.255 no-xauth no-config-mo
de
isakmp key ******** address TX-PIX netmask 255.255.255.255 no-xauth no-config-mo
de
isakmp identity address
isakmp nat-traversal 20
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash md5
isakmp policy 20 group 2
isakmp policy 20 lifetime 86400
isakmp policy 30 authentication pre-share
isakmp policy 30 encryption 3des
isakmp policy 30 hash md5
isakmp policy 30 group 1
isakmp policy 30 lifetime 86400
vpngroup remotectusers address-pool ctpool
vpngroup remotectusers dns-server 172.20.1.5
vpngroup remotectusers wins-server 172.20.1.5
vpngroup remotectusers default-domain morrowny.comAmit,
I applaud your creativity in seeking to solve your problem, however, this sounds like a real mess in the making. There are two things I don't like about your approach. One, cron -> calling Java -> calling PHP -> accessing database, it's just too many layers, in my opinion, where things can go wrong. Two it seems to me that you are exposing data one your website (with the PHP) that you may not want expose and this is an important consideration when you are dealing with emails and privacy and so on.
I think the path of least resistance would be to get a new user account added to the MySQL database that you can access remotely with your Java program. This account can be locked down for read only access and be locked down to the specific IP or IP range that your Java program will be connecting from.
Again I applaud your creativity but truly this seems like a hack because of the complexity and security concerns you are introducing and I think is a path to the land of trouble. Hopefully you will be able to get a remote account set up. -
Download Speed on PIX 515E is Pretty Slow
Hello, I have a PIX 515E set up between our office switch and our Comcast Business Router and the download speeds are not as fast as they should be. We are paying for 30 down 30 up but it's more like 10 down 30 up. I plugged in a computer directly into the router and got 30/30 so I know its not a comcast issue. I think it might be the low amount of memory on the PIX because its running at 109 out of a total 128mb. The PIX has a site-to-site VPN tunnel with a remote ASA 5520 firewall. The inside/outside ports are both auto/auto. The running config is only 161 lines.
Here's some information about the PIX 515E...
Version 8.0(4)
ASDM 6.1(3)
Memory 128MB
Here is the running config..
Result of the command: "show running-config"
: Saved
PIX Version 8.0(4)
hostname --------------------
domain-name -----------------
enable password -------------------------
passwd --------------- encrypted
names
name 1.1.1.1 Data-Center-Firewall #### Outside Address Changed
name 10.0.0.0 Data-Center-Subnet
dns-guard
interface Ethernet0
nameif inside
security-level 100
ip address 10.10.1.1 255.255.255.0 standby 10.10.1.254
interface Ethernet1
nameif outside
security-level 0
ip address 2.2.2.1 255.255.255.252 #### Outside Address Changed
interface Ethernet2
description LAN/STATE Failover Interface
ftp mode passive
clock timezone EST -5
clock summer-time EDT recurring
dns server-group DefaultDNS
domain-name -------------
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service http8080 tcp
description http8080
port-object eq 8080
object-group service DM_INLINE_TCP_1 tcp
port-object range 50000 50100
port-object eq 990
access-list outside_access_in remark ip, tcp/990
access-list outside_access_in extended permit tcp host 1.1.1.1 host 2.2.2.5 object-group DM_INLINE_TCP_1
access-list outside_access_in extended permit icmp any any
access-list ACL-VPN extended permit ip 10.10.1.0 255.255.255.0 Data-Center-Subnet 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
failover
failover lan unit primary
failover lan interface failover Ethernet2
failover lan enable
failover key *****
failover replication http
failover mac address Ethernet0 001e.f732.008f 000d.28f9.628f
failover mac address Ethernet1 001e.f732.0090 000d.28f9.6290
failover link failover Ethernet2
failover interface ip failover 10.10.10.10 255.255.255.252 standby 10.10.10.20
icmp unreachable rate-limit 1 burst-size 1
icmp permit any inside
icmp permit any outside
asdm image flash:/asdm-613.bin
no asdm history enable
arp timeout 14400
nat-control
global (outside) 1 interface
nat (inside) 0 access-list ACL-VPN
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) 2.2.2.5 10.10.1.102 netmask 255.255.255.255
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 2.2.2.2 1
route inside 10.10.0.0 255.255.255.0 10.10.1.2 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 10.10.0.0 255.255.255.0 inside
http 10.10.1.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
service resetoutside
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set AES128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto map MAP-VPN 1 match address ACL-VPN
crypto map MAP-VPN 1 set pfs
crypto map MAP-VPN 1 set peer Data-Center-Firewall
crypto map MAP-VPN 1 set transform-set ESP-3DES-SHA
crypto map MAP-VPN 1 set security-association lifetime seconds 28800
crypto map MAP-VPN 1 set security-association lifetime kilobytes 4608000
crypto map MAP-VPN interface outside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 5
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet 10.10.1.0 255.255.255.0 inside
telnet 10.10.0.0 255.255.255.0 inside
telnet timeout 5
ssh 10.10.0.0 255.255.255.0 inside
ssh 10.10.1.0 255.255.255.0 inside
ssh timeout 5
console timeout 0
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
tunnel-group 1.1.1.1 type ipsec-l2l
tunnel-group 1.1.1.1 ipsec-attributes
pre-shared-key *
class-map class_ftp
match port tcp eq ftp-data
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
class class_ftp
inspect ftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:b795d4f5f5da3d8283d452ba857d5534
: endPlease check on the speed and duplex settings whether the downstream and upstream links are fine and healthy.
Inside/outside are both set to auto/auto at
Check for the processes usage of the cpu of the pix.
CPU is running at 2%
Process: tmatch compile thread, PROC_PC_TOTAL: 2, MAXHOG: 8, LASTHOG: 8
LASTHOG At: 19:01:15 EST Dec 31 1992
PC: 26b616 (suspend)
Process: tmatch compile thread, NUMHOG: 2, MAXHOG: 8, LASTHOG: 8
LASTHOG At: 19:01:15 EST Dec 31 1992
PC: 26b616 (suspend)
Traceback: 26b616 26bdb9 26ec89 1182b3
Process: Dispatch Unit, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At: 09:25:12 EDT Jul 18 2012
PC: 130114b (interrupt)
Traceback: 100178 12edd0c 9771e5 8c0e66 927164 928996 8ec3f5
8ec7ed 79d35e 2780c3 1182b3
Process: Unicorn Admin Handler, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At: 12:27:25 EDT Jul 18 2012
PC: 130114b (interrupt)
Traceback: 100178 d870cb 13016b3 15cf68 e91a6f e9118b abfcea
a7cb2e a7daeb 18d800 5ae9a9 5a6aa0 5a7272 5a75e5
Process: Unicorn Admin Handler, PROC_PC_TOTAL: 4, MAXHOG: 7, LASTHOG: 7
LASTHOG At: 12:34:10 EDT Jul 18 2012
PC: 5ae903 (suspend)
Process: Unicorn Admin Handler, NUMHOG: 4, MAXHOG: 7, LASTHOG: 7
LASTHOG At: 12:34:10 EDT Jul 18 2012
PC: 5ae903 (suspend)
Traceback: 5ae903 5a6aa0 5a7272 5a75e5 5ad3d5 1182b3
Process: Unicorn Admin Handler, PROC_PC_TOTAL: 4, MAXHOG: 5, LASTHOG: 5
LASTHOG At: 12:37:47 EDT Jul 18 2012
PC: f4078b (suspend)
Process: Unicorn Admin Handler, NUMHOG: 4, MAXHOG: 5, LASTHOG: 5
LASTHOG At: 12:37:47 EDT Jul 18 2012
PC: f4078b (suspend)
Traceback: f40be2 130f41e aab54d aac3b0 5a6c2e 5a7272 5a75e5
5ad3d5 1182b3
Process: IKE Daemon, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At: 23:07:40 EDT Jul 19 2012
PC: 1b6dd0 (interrupt)
Traceback: 100178 1b8a31 1baaeb 6438d7 12efc6f 64250b 653fe9
654b78 1182b3
Process: IKE Daemon, PROC_PC_TOTAL: 347, MAXHOG: 31, LASTHOG: 30
LASTHOG At: 16:01:55 EDT Jul 23 2012
PC: 654bab (suspend)
Process: CTM message handler, PROC_PC_TOTAL: 346, MAXHOG: 27, LASTHOG: 27
LASTHOG At: 16:01:55 EDT Jul 23 2012
PC: 2087ec (suspend)
Process: IKE Daemon, NUMHOG: 693, MAXHOG: 31, LASTHOG: 27
LASTHOG At: 16:01:55 EDT Jul 23 2012
PC: 654bab (suspend)
Traceback: 1182b3
Process: Unicorn Admin Handler, NUMHOG: 1, MAXHOG: 5, LASTHOG: 5
LASTHOG At: 17:23:30 EDT Jul 23 2012
PC: 130003b (interrupt)
Traceback: 100178 13008b8 f5a0cd f5ac32 f5ae40 f60828 f617c1
d38a0d aab50b aac14a 5a6c2e 5a7272 5a75e5 5ad3d5
Process: Dispatch Unit, PROC_PC_TOTAL: 227, MAXHOG: 432, LASTHOG: 35
LASTHOG At: 17:37:03 EDT Jul 23 2012
PC: 278207 (suspend)
Process: Dispatch Unit, NUMHOG: 227, MAXHOG: 432, LASTHOG: 35
LASTHOG At: 17:37:03 EDT Jul 23 2012
PC: 278207 (suspend)
Traceback: 278207 1182b3
Process: Unicorn Admin Handler, PROC_PC_TOTAL: 1901, MAXHOG: 8, LASTHOG: 7
LASTHOG At: 17:44:20 EDT Jul 23 2012
PC: 118ed5 (suspend)
Process: Unicorn Admin Handler, NUMHOG: 1901, MAXHOG: 8, LASTHOG: 7
LASTHOG At: 17:44:20 EDT Jul 23 2012
PC: 118ed5 (suspend)
Traceback: 118ed5 b2d032 f5a80d f5ac0a f5ae40 f607e5 f617c1
d38a0d aab50b aac14a 5a6c2e 5a7272 5a75e5 5ad3d5
CPU hog threshold (msec): 5.120
Last cleared: None
Check on the inetrface whetehr u get any crc/input/overrun errors. Please check with the physical connectivity.
Interface Ethernet0 "inside", is up, line protocol is up
Hardware is i82559, BW 100 Mbps, DLY 100 usec
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
MAC address __________, MTU 1500
IP address 10.10.1.1, subnet mask 255.255.255.0
60862937 packets input, 29025667892 bytes, 0 no buffer
Received 1371 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
68515603 packets output, 44084404472 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max packets): hardware (0/1) software (0/47)
output queue (curr/max packets): hardware (0/67) software (0/1)
Traffic Statistics for "inside":
60997029 packets input, 28080179952 bytes
68553614 packets output, 43104566708 bytes
29544 packets dropped
1 minute input rate 63 pkts/sec, 30371 bytes/sec
1 minute output rate 64 pkts/sec, 16557 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 91 pkts/sec, 45254 bytes/sec
5 minute output rate 93 pkts/sec, 56181 bytes/sec
5 minute drop rate, 0 pkts/sec
Interface Ethernet1 "outside", is up, line protocol is up
Hardware is i82559, BW 100 Mbps, DLY 100 usec
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
MAC address ___________, MTU 1500
IP address ___________, subnet mask 255.255.255.252
67730933 packets input, 44248541375 bytes, 0 no buffer
Received 4493 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 L2 decode drops
60418640 packets output, 29310509840 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collisions, 0 deferred
0 lost carrier, 0 no carrier
input queue (curr/max packets): hardware (0/1) software (0/39)
output queue (curr/max packets): hardware (0/42) software (0/1)
Traffic Statistics for "outside":
67782987 packets input, 43276611710 bytes
60562287 packets output, 28342787997 bytes
206651 packets dropped
1 minute input rate 57 pkts/sec, 14273 bytes/sec
1 minute output rate 61 pkts/sec, 30258 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 89 pkts/sec, 54426 bytes/sec
5 minute output rate 87 pkts/sec, 45115 bytes/sec
5 minute drop rate, 0 pkts/sec
enable flowcontrol recieve on on the firewall interfaces and switch/router interfaces connected to the firewall.
Not sure how to do that. -
PIX-515E - Reason 412: the remote peer is no longer responding...
Hi,
I am unable to VPN to my network from outside using cisco VPN client to PIX-515E.
When I try it say:
Reason 412: the remote peer is no longer responding...
From inside everything work ok, I can connect... (same computer, same settings...)
Maybe the problem is not in PIX??
Few days ago I upgrade FWSM from 3.1.x to
FWSM Firewall Version 4.1(9)
Device Manager Version 6.2(2)F
Can this upgrade cause problem???
I compare running conf: and I notice this new commands:
service reset no-connection
no service reset connection marked-for-deletion
I try with opposite:
no service reset no-connection
service reset connection marked-for-deletion
but still I cannot VPN....
Any advice?
THX,
IvanProblem solved...
as usual I cause the problem instead of 8 i wrote 3... i was checking that IP address several time but didn't see
now when I was preparing to put running config online and replacing ip address ... something jump into my eye....
So thnx Jennifer :-) -
Cisco PIX-515e reset to factory defaults *Expert Advice Only Please*
Hi,
I have a cisco PIX-515e which i have connected to a emulator through the console port, and im having trouble erasing data from it.
I can get into 'pixfirewall' mode and 'monitor' mode but thats as far as i get. i have tried 'write erase' and 'configure factory-default' in both modes to no success.
When i last posted this i had alot of replies mentioning ROMMON mode but i want to stress the PIX 515e does not have ROMMON mode it has MONITOR mode however the commands are not the same as ROMMON commands.
Any help would be much appreciated.
thanks,8 MB RAM
PCI Device Table.
Bus Dev Func VendID DevID Class Irq
00 00 00 8086 7192 Host Bridge
00 07 00 8086 7110 ISA Bridge
00 07 01 8086 7111 IDE Controller
00 07 02 8086 7112 Serial Bus 9
00 07 03 8086 7113 PCI Bridge
00 0D 00 8086 1209 Ethernet 11
00 0E 00 8086 1209 Ethernet 10
00 11 00 14E4 5823 Co-Processor 11
00 13 00 8086 B154 PCI-to-PCI Bridge
01 04 00 8086 1229 Ethernet 11
01 05 00 8086 1229 Ethernet 10
01 06 00 8086 1229 Ethernet 9
01 07 00 8086 1229 Ethernet 5
Cisco Secure PIX Firewall BIOS (4.2) #0: Mon Dec 31 08:34:35 PST 2001
Platform PIX-515E
System Flash=E28F128J3 @ 0xfff00000
Use BREAK or ESC to interrupt flash boot.
Use SPACE to begin flash boot immediately.
Reading 123392 bytes of image from flash.
PIX Flash Load Helper
Initializing flashfs...
flashfs[0]: 8 files, 3 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 16128000
flashfs[0]: Bytes used: 13963264
flashfs[0]: Bytes available: 2164736
flashfs[0]: Initialization complete.
Booting first image in flash
Launching image flash:/pix722.bin
128MB RAM
Total NICs found: 6
mcwa i82559 Ethernet at irq 10 MAC: 0016.9da2.5907
mcwa i82559 Ethernet at irq 11 MAC: 0016.9da2.5908
mcwa i82559 Ethernet at irq 11 MAC: 000d.8810.d91c
mcwa i82559 Ethernet at irq 10 MAC: 000d.8810.d91d
mcwa i82559 Ethernet at irq 9 MAC: 000d.8810.d91e
BIOS Flash=am29f400b @ 0xd8000 MAC: 000d.8810.d91f
Initializing flashfs...
flashfs[7]: 8 files, 3 directories
flashfs[7]: 0 orphaned files, 0 orphaned directories
flashfs[7]: Total bytes: 16128000
flashfs[7]: Bytes used: 13963264
flashfs[7]: Bytes available: 2164736
flashfs[7]: flashfs fsck took 15 seconds.
flashfs[7]: Initialization complete.
Licensed features for this platform:
Maximum Physical Interfaces : 6
Maximum VLANs : 25
Inside Hosts : Unlimited
Failover : Active/Active
VPN-DES : Enabled
VPN-3DES-AES : Enabled
Cut-through Proxy : Enabled
Guards : Enabled
URL Filtering : Enabled
Security Contexts : 2
GTP/GPRS : Disabled
VPN Peers : Unlimited
This platform has an Unrestricted (UR) license.
Encryption hardware device : VAC+ (Crypto5823 revision 0x1)
| |
||| |||
.|| ||. .|| ||.
.:||| | |||:..:||| | |||:.
C i s c o S y s t e m s
Cisco PIX Security Appliance Software Version 7.2(2)
****************************** Warning *******************************
This product contains cryptographic features and is
subject to United States and local country laws
governing, import, export, transfer, and use.
Delivery of Cisco cryptographic products does not
imply third-party authority to import, export,
distribute, or use encryption. Importers, exporters,
distributors and users are responsible for compliance
with U.S. and local country laws. By using this
product you agree to comply with applicable laws and
regulations. If you are unable to comply with U.S.
and local laws, return the enclosed items immediately.
A summary of U.S. laws governing Cisco cryptographic
products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by
sending email to [email protected].
******************************* Warning *******************************
Copyright (c) 1996-2006 by Cisco Systems, Inc.
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cryptochecksum (unchanged): 43dccc97 2fb4bfec 15a33bef dad78b7e
Type help or '?' for a list of available commands.
pixfirewall>
I am unable to get onto enable mode because i do not no the password? any idea of a way round, i need to get into that enable mode.
Maybe you are looking for
-
Is Apple TV ever going to get more British channels? BBC, ITV, More 4 players Apps like Facebook.
-
CDN Endpoint not working anymore
Since 14 hours our cdn is not working. We have not changed anything in the portal, and everthing reports OK. How can I troubleshoot this? http://*id*.vo.msecnd.net/500/5300032-600.jpg (not working) http://*storageaccount*.blob.core.windows.net/500/53
-
Version in standard analysis of LIS
Hi Experts, Iam using MCSI transaction to analyse the data of the information structure created.But in the selection screen of MCSI, Iam not finding the filed for version. So system always considers the actual version 000. In SAP help, its mentioned
-
Security prompt from Java with missing checkbox
Hello, In our application we use jnlp link to launch java windows. When we click on the link, appear a sécurity prompt containing, the application name, the editor and 2 location for jnlp (The server adress and on a second line the text "Launched fro
-
Play music through computer with out itues
i just got my finance a 1gig nano for her birthday and we loaded songs on the ipod at home. now she wants to play her music at work through her work computer. she is not allowed to load software on her computer at work, so she cant load itues on it.