Port Forwarding in WRT54GL Router does not work

When i forward ports in the firware it does not work correctly. I tested it using http://www.yougetsignal.com/tools/open-ports/ and it still said that the port was closed.

Who is your ISP. When you do port forwarding make sure you have entered the IP address of the computer for which you need to enable port forwarding. Under "Security" Tab uncheck "Block Anonymous Internet Request" and click on Save Settings.After this try testing if that port is opened or not.What ports numbers you are trying to open on your router.

Similar Messages

Port Forwarding on Home Hub 5 not working

Hi,
Is anybody else having problems getting ports to forward on their Home Hub or Home Hub 5?
I am a new BT customer, less than a week infact and BT have been utterly hopeless in getting this resolved. All they do is send me instructions for port forwarding on a homehub which I do not need and tell me that i need to pay for their tech support to investigate it further which is freaking ridiculous considering port forwarding is an essential part of any router and this router is brand new, less than a week old. (Do BMW sell you a car and then refuse to take responsibility for a broken engine?)
My other option is buying an ADSL 802.11ac router for £150 which out of principle, i dont think i should have to do. One of the reasons i came to BT in the first place was because the homehub is supposed to be one of the best free provider supplied routers around.
Please only reply to this if you know what you are talking about or have experienced this same issue yourselves. I reiterate that I have not missed any configuration steps on my part and this is a case of the homehub simply not working as it is designed.
Scenario:
I like to have remote desktop access to my home computer from external networks. I do not use 3rd party software such as 'log me in' or 'team viewer', I like to use Microsoft Remote desktop and had been doing so for years with my Sky broadband until last week.
I have dynamic DNS running on my machine which updates my constantly changing external IP to the dns server so dont worry about that, thats all good.
I have correctly set up the forwarding of TCP 3389 to the static I.P of my home desktop on the homehub (and rebooted and or factory reset several times)
Result:
Nothing. The homehub displays as though it has forwarded the ports yet i am still unable to remote in from an external network. The port shows as closed when i run a port scanner.
The same goes for other ports I have tried to open. For example, my Xbox One.
BT are sending me out a replacement Hub to try but I fear that this will have the same result as i have seen a few other people post with the same issues.
If anybody has experienced and or resolved this, please let me know and i will be forever grateful
Thank you

When you do a major network revision always reset the TC to factory and start over.. it simply remembers too much of the last setup.
Plug WAN TC into the HH5 and run through the airport utility again. The TC must go into bridge mode. It then should work fine, but I recommend particularly with Mavericks you use strict naming.
Not apple names.. long, loose and loopy.
Names that are short, 2-10 characters is plenty but make an upper limit of 20.
No spaces..
Pure alphanumeric.. no apostrophe or any other odd character.

Port Forwarding for RDP 3389 is not working

Hi,
I am having trouble getting rdp (port 3389) to forward to my server (10.20.30.20). I have made sure it is not an issue with the servers firewall, its just the cisco. I highlighted in red to what i thought I need in my config to get this to work. I have removed the last 2 octets of the public IP info for security .Here is the configuration below:
TAMSATR1#show run
Building configuration...
Current configuration : 11082 bytes
version 15.2
no service pad
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
hostname TAMSATR1
boot-start-marker
boot system flash:/c880data-universalk9-mz.152-1.T.bin
boot-end-marker
logging count
logging buffered 16384
enable secret
aaa new-model
aaa authentication login default local
aaa authentication login ipsec-vpn local
aaa authentication login ciscocp_vpn_xauth_ml_1 local
aaa authorization console
aaa authorization exec default local
aaa authorization network groupauthor local
aaa session-id common
memory-size iomem 10
clock timezone CST -6 0
clock summer-time CDT recurring
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-1879941380
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-1879941380
revocation-check none
rsakeypair TP-self-signed-1879941380
crypto pki certificate chain TP-self-signed-1879941380
certificate self-signed 01
3082024B 308201B4 A0030201 02020101 300D0609 2A864886 F70D0101 04050030
31312F30 2D060355 04031326 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 31383739 39343133 3830301E 170D3131 30393136 31393035
32305A17 0D323030 31303130 30303030 305A3031 312F302D 06035504 03132649
4F532D53 656C662D 5369676E 65642D43 65727469 66696361 74652D31 38373939
34313338 3030819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281
8100BD7E 754A0A89 33AFD729 7035E8E1 C29A6806 04A31923 5AE2D53E 9181F76C
ED17D130 FC9B5767 6FD1F58B 87B3A96D FA74E919 8A87376A FF38A712 BD88DB31
88042B9C CCA8F3A6 39DC2448 CD749FC7 08805AF6 D3CDFFCB 1FE8B9A5 5466B2A4
E5DFA69E 636B83E4 3A2C02F9 D806A277 E6379EB8 76186B69 EA94D657 70E25B03
542D0203 010001A3 73307130 0F060355 1D130101 FF040530 030101FF 301E0603
ip dhcp excluded-address 10.20.30.1 10.20.30.99
ip dhcp excluded-address 10.20.30.201 10.20.30.254
ip dhcp excluded-address 10.20.30.250
ip dhcp pool tamDHCPpool
import all
network 10.20.30.0 255.255.255.0
default-router 10.20.30.1
domain-name domain.com
dns-server 10.20.30.20 8.8.8.8
ip domain name domain.com
ip name-server 10.20.30.20
ip cef
no ipv6 cef
license udi pid CISCO881W-GN-A-K9 sn
crypto vpn anyconnect flash:/webvpn/anyconnect-dart-win-2.5.3054-k9.pkg sequence 1
ip tftp source-interface Vlan1
class-map type inspect match-all CCP_SSLVPN
match access-group name CCP_IP
policy-map type inspect ccp-sslvpn-pol
class type inspect CCP_SSLVPN
pass
zone security sslvpn-zone
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
crypto isakmp policy 20
encr aes 192
authentication pre-share
group 2
crypto isakmp key password
crypto isakmp client configuration group ipsec-ra
key password
dns 10.20.30.20
domain tamgmt.com
pool sat-ipsec-vpn-pool
netmask 255.255.255.0
crypto ipsec transform-set ipsec-ra esp-aes esp-sha-hmac
crypto ipsec transform-set TSET esp-aes esp-sha-hmac
crypto ipsec profile VTI
set security-association replay window-size 512
set transform-set TSET
crypto dynamic-map dynmap 10
set transform-set ipsec-ra
reverse-route
crypto map clientmap client authentication list ipsec-vpn
crypto map clientmap isakmp authorization list groupauthor
crypto map clientmap client configuration address respond
crypto map clientmap 10 ipsec-isakmp dynamic dynmap
interface Loopback0
ip address 10.20.250.1 255.255.255.252
ip nat inside
ip virtual-reassembly in
interface Tunnel0
description To AUS
ip address 192.168.10.1 255.255.255.252
load-interval 30
tunnel source
tunnel mode ipsec ipv4
tunnel destination
tunnel protection ipsec profile VTI
interface FastEthernet0
no ip address
interface FastEthernet1
no ip address
interface FastEthernet2
no ip address
interface FastEthernet3
no ip address
interface FastEthernet4
ip address 1.2.3.4
ip access-group INTERNET_IN in
ip access-group INTERNET_OUT out
ip nat outside
ip virtual-reassembly in
no ip route-cache cef
ip route-cache policy
ip policy route-map IPSEC-RA-ROUTE-MAP
duplex auto
speed auto
crypto map clientmap
interface Virtual-Template1
ip unnumbered Vlan1
zone-member security sslvpn-zone
interface wlan-ap0
description Service module interface to manage the embedded AP
ip unnumbered Vlan1
arp timeout 0
interface Wlan-GigabitEthernet0
description Internal switch interface connecting to the embedded AP
switchport mode trunk
no ip address
interface Vlan1
description $ETH-SW-LAUNCH$$INTF-INFO-HWIC 4ESW$
ip address 10.20.30.1 255.255.255.0
ip nat inside
ip virtual-reassembly in
ip tcp adjust-mss 1452
ip local pool sat-ipsec-vpn-pool 10.20.30.209 10.20.30.239
ip default-gateway 71.41.20.129
ip forward-protocol nd
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip dns server
ip nat inside source list ACL-POLICY-NAT interface FastEthernet4 overload
ip nat inside source static tcp 10.20.30.20 3389 interface FastEthernet4 3389
ip nat inside source static 10.20.30.20 (public ip)
ip route 0.0.0.0 0.0.0.0 public ip
ip route 10.20.40.0 255.255.255.0 192.168.10.2 name AUS_LAN
ip access-list extended ACL-POLICY-NAT
deny   ip 10.0.0.0 0.255.255.255 10.20.30.208 0.0.0.15
deny   ip 172.16.0.0 0.15.255.255 10.20.30.208 0.0.0.15
deny   ip 192.168.0.0 0.0.255.255 10.20.30.208 0.0.0.15
permit ip 10.20.30.0 0.0.0.255 any
permit ip 10.20.31.208 0.0.0.15 any
ip access-list extended CCP_IP
remark CCP_ACL Category=128
permit ip any any
ip access-list extended INTERNET_IN
permit icmp any any echo
permit icmp any any echo-reply
permit icmp any any unreachable
permit icmp any any time-exceeded
permit esp host 24.153. host 66.196
permit udp host 24.153 host 71.41.eq isakmp
permit tcp host 70.123. host 71.41 eq 22
permit tcp host 72.177. host 71.41 eq 22
permit tcp host 70.123. host 71.41. eq 22
permit tcp any host 71..134 eq 443
permit tcp host 70.123. host 71.41 eq 443
permit tcp host 72.177. host 71.41. eq 443
permit udp host 198.82. host 71.41 eq ntp
permit udp any host 71.41. eq isakmp
permit udp any host 71.41eq non500-isakmp
permit tcp host 192.223. host 71.41. eq 4022
permit tcp host 155.199. host 71.41 eq 4022
permit tcp host 155.199. host 71.41. eq 4022
permit udp host 192.223. host 71.41. eq 4022
permit udp host 155.199. host 71.41. eq 4022
permit udp host 155.199. host 71.41. eq 4022
permit tcp any host 10.20.30.20 eq 3389
evaluate INTERNET_REFLECTED
deny   ip any any
ip access-list extended INTERNET_OUT
permit ip any any reflect INTERNET_REFLECTED timeout 300
ip access-list extended IPSEC-RA-ROUTE-MAP
deny   ip 10.20.30.208 0.0.0.15 10.0.0.0 0.255.255.255
deny   ip 10.20.30.224 0.0.0.15 10.0.0.0 0.255.255.255
deny   ip 10.20.30.208 0.0.0.15 172.16.0.0 0.15.255.255
deny   ip 10.20.30.224 0.0.0.15 172.16.0.0 0.15.255.255
deny   ip 10.20.30.208 0.0.0.15 192.168.0.0 0.0.255.255
deny   ip 10.20.30.224 0.0.0.15 192.168.0.0 0.0.255.255
permit ip 10.20.30.208 0.0.0.15 any
deny   ip any any
access-list 23 permit 70.123.
access-list 23 permit 10.20.30.0 0.0.0.255
access-list 24 permit 72.177.
no cdp run
route-map IPSEC-RA-ROUTE-MAP permit 10
match ip address IPSEC-RA-ROUTE-MAP
set ip next-hop 10.20.250.2
banner motd ^C
UNAUTHORIZED ACCESS TO THIS NETWORK DEVICE IS PROHIBITED.
You must have explicit permission to access or configure this device. All activities performed on this device are logged and violations of this policy may result in disciplinary and/or legal action.
^C
line con 0
logging synchronous
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
line vty 0
access-class 23 in
privilege level 15
logging synchronous
transport input telnet ssh
line vty 1 4
access-class 23 in
exec-timeout 5 0
privilege level 15
logging synchronous
transport input telnet ssh
scheduler max-task-time 5000
ntp server 198.82.1.201
webvpn gateway gateway_1
ip address 71.41. port 443
http-redirect port 80
ssl encryption rc4-md5
ssl trustpoint TP-self-signed-1879941380
inservice
webvpn context TAM-SSL-VPN
title "title"
logo file titleist_logo.jpg
secondary-color white
title-color #CCCC66
text-color black
login-message "RESTRICTED ACCESS"
policy group policy_1
   functions svc-enabled
   svc address-pool "sat-ipsec-vpn-pool"
   svc default-domain "domain.com"
   svc keep-client-installed
   svc split dns "domain.com"
   svc split include 10.0.0.0 255.0.0.0
   svc split include 192.168.0.0 255.255.0.0
   svc split include 172.16.0.0 255.240.0.0
   svc dns-server primary 10.20.30.20
   svc dns-server secondary 66.196.216.10
default-group-policy policy_1
aaa authentication list ciscocp_vpn_xauth_ml_1
gateway gateway_1
ssl authenticate verify all
inservice
end

Hi,
I didnt see anything marked with red in the above? (Atleast when I was reading)
I have not really had to deal with Routers at all since we all access control and NAT with firewalls.
But to me it seems you have allowed the traffic to the actual IP address of the internal server rather than the public IP NAT IP address which in this case seems to be configured to use your FastEthernet4 interfaces public IP address.
There also seems to be a Static NAT configured for the same internal host so I am wondering why the Static PAT (Port Forward) is used?
- Jouni

Technicolor router does not work for Gta Online

I currently have the Technicolor home internet router/modem. I have no problems with this router other than with GTA Online. I have of course, followed the Rockstar Technical Support page but this did not help. I tried every step including Open NAT, port forwarding, and DMZ,. The only step I haven't tried is setting my router to bridge mode but I would like to see of there is an alternative other than just simply buying a new router. Thank You

Your Technicolor modem will NEVER work with gta online. I have troubleshooted extensively and there is no way. Unless you are a computer genius, you will never play GTA online with that modem. Go to comcast and complain, get the new xb3 modem, and demand compensation for having to pay rent on a faulty device. I got a $40 credit today for having paid rent on this crappy modem. I'm re-purchasing gta later today and I hope it works with my new router...

Wireless Router does not work

I am at a university that does not want you to use wireless routers, yet everyone around me still has theirs and when i open my Airport dropdown, i see numerous wireless networks that are run by students.
My router is the ZyXEL HS-100W (a cheap router, but it has always worked for me in the past).
When i turn the wireless on through the router's firmware, it is registered on my airport's list, and when i type in my password (WPA), I get the green light in network prefrences and it says something along the lines of "user assigned IP" I have full bars, and it says I am connected, yet whenever i try to open a webpage, it says that I am not connected to the internet.
I tried to turn the firewall off inside the router, and it did nothing, I tried to use no security to see if that would work, and it did not.
I do know that we have to register MAC addresses with the computer department here, so I am not sure if there is a way to do this within OSX or within the firmware.
I know that this is probably very vague, but I am looking for whatever support I can get.
Thanks
ben

it was a good suggestion, but i cannot find a place to manually set a MAC.
The closest i could find is under the WAN page, there is a tab called WAN MAC.
in that tab is "spoof this computer's MAC Address - IP Address" and then has a spot to input an ip address (the default is in the 192.168.. just generic ip).
i tried to input my computer's ethernet mac address, and it didnt work.
maybe there are futher suggestions based on this?
also, i am not sure if this matters, but when the router is plugged in, and I am wired to the router, i can get internet, but once i switch to wifi, i dont get internet. maybe that will help.
thanks
ben

WRT110 Firmware Upgrade Crashed IE8, Router Does Not Work

Last night, at 2:30am EST I felt the need to upgrade the firmware on my router. I downloaded the latest firmware for the WRT110 v1.0 and attempted to upgrade the firmware. Close to the end of the firmware upgrade process IE8 crashed and left my router in a state of limbo.
I called Linksys support only for them to tell me that I have 3 options (all which included paying money to them) :
Pay $40 to add 6 months of extended warranty to the router and support for it
Pay $30 for a one time support call
Buy a new router through them with waived shipping.
This wasn't exactly what I wanted to hear at 3 am, so naturally I was quite irritated. Of course, the supervisor asking me if I was sure I downloaded the correct firmware and telling me to go on the internet when it's obviously not working really did not help either.
I tried the two reset options suggested by the forums here and the supervisor on the phone, pressing down the reset button for 30 seconds and pressing it down for a minute and unplugging for 30 seconds. Neither worked, so the supervisor essentially told me the router needed to be replaced.
Now, is there any actual way of getting the router back to a working state?

There is always a way. Check this topic and follow the procedures.

Mini Display Port to Dual Link DVI Does Not Work Right

Somebody said here that this was an isolated problem. Well, I just got my new MacBook Pro 15", used the adapter to hook to the 30" Dell monitor, and it works a few minutes, then the screen distorts.
Count me among the isolated problems- it is beginning not to look isolated.
Now, do I wait on Apple to fix the problem, or do I return the MacBook Pro while still in the return period?

Hi, Matt, and welcome to Apple Discussions.
The Matrox Support only told me that the new MacBook Pro with Mini Display Port is not supported, but as it's working for 2x1680x1050 with the Dual-Link DVI adapter, I was wondering if the Mini Display Port to Dual-Link DVI Adapter could be the problem.
I suspect that what Matrox Support meant when they said "not supported" was, in fact, "not supported": i.e., they've tried it and it doesn't work satisfactorily. You've tried it too, and found that to be true. Now you just need to come to terms with the fact. Matrox is quite open about it; it's not a secret. See the 9400M/9600MGT MacBook Pro entry in this compatibility table from Matrox's web site:
http://www.matrox.com/graphics/en/support/compatibility/gxm/resolutions/

WRT300N Router does not working with Intel 4965AGN adapter on Wireless-N

Hi! I have recently bought the laptop Acer 5920G with Intel 4965AGN network adapter and Windows Vista. I have read that WRT300N Router is supporting Draft-N standard, so I purchased it. The router is working fine on Wireless-G 54Mbps (firmware - 2.00.17), but not on Wireless-N. I tried to enter the following settings: ssid - any non-linksys name; radio band - wide; n-channel - 9; standard channel - 11; beacon interval - 50; Fragmentation threshold - 2306; RTS threshold - 2307, but nothing has happened, connection still remains 54Mbps. How should I configure the router and network adapter to get Wireless-N?

okay... try reflashing/upgrading the firmware on the router, after reflashing the firmware on the router, reset it back to default settings and reconfigure it according to ISP settings...edit the wireless settings again, make sure that "wireless mode" should be mixed...
on the vista computer, click on start >> control panel >> network & sharing center >> manage wireless network and try removing existing wireless networks from profile and manually add wireless n/w profile according to wireless settings of the router...check whether it makes any difference or not and let me know.

Forward to several addresses does not work with Yahoo account

My wife uses a MacBook Air and a YahooPlus in Mail.
It works well except when she wants to forward mail to several addresses.
She gets an error message (something about smtp server...don't know exactly)
When she forwards the mail one by one it works.
In the old days when she was on Windows she used Yahoo's website mail and had no problems forwarding to several people, so the problem must be related to Mail and not Yahoo.
Can anyone help?
Thanks

Bump

MAC address filter on router does not work for iOS8

The MAC address randomization feature in iOS8 is great for privacy, but this being the case, I am not able to connect to a wi-fi router that employs a MAC address filter. Is there a way to turn off this MAC address randomization?

I had this problem. I followed the directions to replace the netinfo db's. I rebooted, and started going through the initial OS X welcome stuff. When I tried to re-enter my user stuff, I got a "sorry, standard user cannot be added" error, and the machine went to a blue screen.
This is odd, as I have completely restored the system from scratch (reformatted the hard drives, reinstalled). The first boot up it works fine. It seems that one of the updates must be screwing it up, because after it gets through updating, when it reboots, I can't log in.

The parental control function on my Verizon MI424WR Router does not work

I created few rules on the Parental Control section of my MI424WR Router admin page but it still allows internet access.
Does this router completely shut down the internet access, lets say if I set it 10pm-12am Disable connection? I read someone's comment on another post, MI424WR is actually cuts down the bandwidth into 1/2, but not completely shut down the connection. Is this true? If so this is useless....

Parental controls can block all access. The bandwidth reduction info is wrong.

WPS push button on the Linksys WRT610N router does not work. Please help.

Hi,
I am facing problems of the WPS Push Button on the Linksys WRT610N version 2.0 router which has stopped working. I don't see the Blue LED blinking. The WPS button no more works on the router. It was working before. I did a firmware upgrade. Could this be the cause?
Please help me in solving this issue at the earliest.
Leo.

when you reset the router, did you notice that your network name changed?
also check the settings on the router if the wps is enabled.
with a computer wired to the router, are you able to go online?
follow the instructions in this page to setup wps
to connect another computer to the network, follow the instructions here

USB Port does not work W510

Hello all,
I am writing to you hoping that one of you may have an idea what's wrong with my beloved w510.
A few hours ago the usb port (on the back on the right side) where I plugged in my external mouse stopped working.
In the Lenovo part list it is referred to as "usb Sub card yellow".
It just does not recognize a mouse nor any usb stick or external drive. I have already reinstalled the usb controller
but it didn't make any difference. (I think the driver is only for the usb 3 hub on the left side of the notebook)
when I plug in the external drive the lights of the drive start "flashing" same for the usb stick, but they are not recognized as drives..Same for the mouse. The lights go on, but nothing else works.
Probably its all my fault, but I don't know what else I can try! Please excuse my bad English...!
Hoping that somebody might be able to help me...
Paul

I have a reproducible test for this issue on my W510.
1) Plug in a usb mouse into the rear usb port and ensure the mouse is working.
2) Hybernate the system.
3) Resume the system.
4) Confirmed the mouse does not work.
5) Disconnect and attach the mouse to one of the left usb ports and confirm the mouse works.
6) Disconnect and attach to the rear usb port and confirm the mouse does NOT work.
7) Restart the system and confirm the mouse still does NOT work.
8) Shut down the computer (a full shutdown, not standby or hybernate).
9) Power the system back on.
10) Confirm the mouse is now working in the rear port.
I can do these steps over and over with the same results regardless of whether the AC adapter is plugged in or not. It appears that the data connection does not work after the system is resumed from a sleeping state. I have the latest UltraNav driver and utility and the latest power management updates.
Oh, and one more test. Hybernate the system with nothing plugged in, then plug in a mouse into the rear usb port when the system is presently hybernated and then power the system back on. The mouse will not work and rebooting doesn't correct it. Only a full shutdown fixes it.

Persistant routes sometimes not working

This is the situation
We have a MSSQL cluster of 2 servers the SQL03A and SQL03B windows 2008 R2 enterprise on vmware 5.5
There are 2 persistant routes, they are for the backup:
10.64.67.171 255.255.255.255 10.37.4.30
10.64.67.169 255.255.255.255 10.37.4.29
Sometimes , one?s a month, the persistant route does not work and the backup wil not work.
We delete the persistant route and we make the persistant route again, than it wil work again.
What could be the problem?

You need to use root print to list the available routes. When the problem gets reproduced again, please run it to see what are the available routes.
Also, you can double check that you are creating the routes properly. Here is an article about how to create persistent routes: http://www.itsyourip.com/networking/howto-add-persistent-static-routes-in-windows/comment-page-1/
This posting is provided AS IS with no warranties or guarantees , and confers no rights.
Ahmed MALEK
My Website Link
My Linkedin Profile
My MVP Profile

Router does not answer

My router does not work with my computer but it works with my external driver. Also I have a PC conected to the router and it works...

My router does not work with my computer but it works with my external driver.
I don't understand the second part of that sentence.
As far as your computer is concerned,
1. Change the ethernet cable.
2. Open a browser on your Mac, and enter the router's ip - the manual will tell you what it is. Usually something like 192.168.1.1. You may have to wait for a response. If you do get a response. it will be a log-in window asking for a name and password. This info too should be in the manual.
3. Follow the instructions to set up your Mac to communicate with the router.
If this does not work, post back with a description of what happened.

Port Forwarding in WRT54GL Router does not work

Similar Messages

Maybe you are looking for