Powerbook 15" 1.5 Ethernet port

Hello, I bought a refurbished Powerbook 15" aluminum from Apple in September.
Went to plug in an ethernet cable last night and I couldn't get it to click in. Tried 4 different cables (both ends, so 8 RJ connectors) with no luck. Is my ethernet port damaged? The cable will push in no problem but it never clicks or has any retention. Just kind floats around.
Where do I go from here? Also, I looked around a bit and couldn't find a phone number for Apple. Anyone have it?

Just to follow up. Called Apple tech support. 1st guy I spoke to was a little rough but one of their specialist was extremely helpful and courteous. Looks like it's going to need to be replaced when I get back in the States. I was able to establish a connection with my router via the ethernet port but the cable is not secure. Thanks for the help guys. Much appreciated.
Jeff

Similar Messages

  • Ethernet port dead on Powerbook firewire

    ethernet port dead on my Powerbook Firewire 400MHZ G3 1GB RAM 40GB HARD DRIVE DVD-ROM
    I tried Open Firmware Reset and PRAM RESET AND WOULD I NEED TO GET A NEW LOGIC BOARD.
    Joshua Lich
    The port stopped working for 2 months and i have no AHT DISKS OR PROPER IMAGES TO DO SO

    Hi, and Welcome to the Forums..
    Ok, since you already did a PRAM reset and that didn't resolve the problem.. there is ONE LAST step before we can say it is or could be the logic board.. Do a PMU reset. This is a hard reset where you would have to do the following:
    A full (PMU) reset of the Pismo (Apple calls it a 'PowerBook (FireWire)') follows: If the computer is on, turn it off. Press and release the reset button located on the rear panel of the computer between the external video and modem ports. Wait 5 seconds. Press the Power button to restart the computer.
    If and only if you do this and the problem is not resolved, either you will need the Apple Hardware Test which came packaged with the Pismo or you will need MacTest Pro also called: Apple Service Diagnostic to do further diagnostic checking on the Pismo's ethernet port.
    Try the PMU reset above and report back.. Try to then plug in an ethernet cable and see if u can get any response from it. If not, I would suggest getting the AHT or MTP from someone.. Actually, if you email me I might be able to further assist as I DO have the tools to make your Pismo work again, hopefullly assuming its not a logic board issue.
    Romko

  • Can I convert a PB 1400's PC card port to a ethernet port for file sharing?

    My plan here is to connect a PowerBook 1400cs/133 running OS 8.6 to an iBook G4 running OS 10.4 by means of an ethernet crossover cable, and move my important files (ClarisWorks 4.0 docs and games mostly) to the new computer. But the PB 1400 has no ethernet port! Is there something I can put in the PC card slot that will convert it to an ethernet port?

    jpl, Denis, here's my setup:
    The PB 1400 is connected to the iBook via a Farallon EtherWave/EtherMac Ethernet PC Card (with a blue arrow, PCMCIA 2.1, PC Card Standard). I have the Farallon software installed and the Farallon extension turned on. A "Farallon EN Card" icon appears on my desktop, and the little light on the cord where it connects to the card is green. I used to use the card to connect to the internet back in the day when the 1400 was my primary computer, so I'm confident it works.
    The PB 1400 (name: Ben's PowerBook 1400): AppleTalk, configured to connect via alternate ethernet. File sharing, on. TCP/IP, connected via AppleTalk (Mac IP). I've tried configuring that both "Using Mac IP server" and manually by entering in the iBook's IP address and router address (the 1400 is not connected to the internet). As far as I can tell, Users/Groups is configured; it has "Ben" as "user" and "Guest" as "guest user."
    The iBook (name: Ben's iBook G4) is set up basically identical to the way jpl describes his iMac above. Like his, the services panel of sharing on the iBook says "Other Macintosh users can access your computer at afp://x.x.x.6." I also manually entered the iBook's IP address, subnet mask, and router. Under my shared location, under Built-in Ethernet, TCP/IP is configured and AppleTalk is active.
    Still, file sharing is not working. When I try to access the iBook from the 1400, I go to the Chooser, click the AppleShare icon, and "Ben's iBook G4" in the file server window. When I select it and click OK, I go to a screen to enter my name (Ben) and password as a registered user. I'm not sure if the password it wants is the file sharing password I set up for the 1400 or the administrator password for the iBook, so I tried them both. I also tried connecting as a "guest." In all cases, after I hit the "Connect" button, I got the error message "The connection to this server has been unexpectedly broken."
    No luck going the opposite direction either. When I go to Go: Connect to Server: Browse on the iBook, "Ben's PowerBook 1400" appears in the Network area, but when I select it and hit the "connect" button, I get this error message: "The file server uses an incompatible version of the AFP protocol. You cannot connect to it."

  • Ethernet port sometimes fails

    I have a new router from O2, my new ISP, and while I can connect my Powerbook (15" G4) wirelessly, I cannot connect through the ethernet port. Network Diagnostics says that the ethernet cable is not connected to the Powerbook, which is incorrect as it is properly connected. The router shows no ethernet connection, which is consistent with the problem.
    But, if I connect the router by ethernet to my Time Capsule and then connect the Powerbook to the Time Capsule with the ethernet cable, it works fine.
    Also, if I connect the Powerbook by ethernet through my Devolo network from the router, it works fine again.
    So there is clearly an incompatibility between the Powerbook and the new router which is somehow fixed by being washed through the Time Capsule or Devolo.
    I have also while traveling had a problem connecting to the internet through the ethernet while my son's Windows laptop has worked fine.
    All my ethernet connections are set to automatic.
    I do not know the router manufacturer as it is only branded O2.
    O2 are unable to suggest an answer. Has anyone here any ideas?
    Thanks.

    Yes, it is yellow - how did you guess?
    Crossover cables are supposed to be yellow, though I've seen a few that weren't.
    See the bottom of this page to see how they are wired differently inside...
    http://www.incentre.net/incentre/frame/ethernet.html
    At one time, to connect two Ethernet computers, you had to have a crossover cable, so the in & out signals wouldn't be butting heads, then Ethernet Ports got intelligent and could automatically switch the lines internally, yet the modern ones can get confused by it already being crossed when it's trying to cross them internally.

  • Airport Express Ethernet Port for XBOX

    Please could somebody help me!!!
    I have the new Airport Extreme in my home office running an 80211n network. It is also connected by one of its ethernet ports to my first airport express providing my home with an 80211g network for our older powerbooks.
    I have a second Airport Express in my living room which is plugged into my Sony Receiver for use with airtunes.
    Question - we have just got an XBOX. It is located in the living room next to the second Airport Express. I want to plug the xbox into the LAN port on the airport express so that the XBOX can access the internet. Please could somebody explain how I do this. (I do not have the wireless adapter for the XBOX).
    Many thanks!

    Thanks for the help. I followed your directions and the info in the linked page. Everything appeared to configure correctly. However, the xbox still does not get a connection. The xbox is connected to the 2nd AX using an ethernet cable. Am I meant to somehow tell this AX to allow its single WAN port to act as a LAN port? Or is this meant to be automatic? Also, do I need to set this AX to distribute IPs... or will the 1st AX do that? In other words how does the xbox get an IP. Any other ideas???
    I am really grateful for any help you can offer...

  • Airport Express ethernet port turned off?

    I have an Airport Extremme base station successfully sending out a wireless network to Airport-card equipted Powerbooks- no problem. But I also have Mac tower which does not have an airport card and is too far away to reach by Ethernet cable.
    Before a recent move, I was able to get this computer on the wireless network by ethernet-cabling it directly an Airport Express (which was joined to the existing network).
    I can't find a combination that makes this work again. The ethernet port in the Express seems to be deactivated.

    Thanks very much. WDS was the missing factor. After trying several permutations of WDS settings and address distribution settings between the Airport Extreme and the Express, things started working.
    I've said it before: Apple-provided documentation and online articles are skimpy. I can only imagine they do this to give the appearance of simplicity, even when the issues are complex. I'd say: give the "easy set-up" instructions - but give us the "expert" guide as well!
    This function of having the Express serve as an Airport card replacement should provide solution for the owners of Macs without Airport card (like many buyers of recent G5 duals like myself who discovered too late that we could not install airport cards ourselves).

  • Airport Express Ethernet Port  Question  (Please);

    Hello,
    Senario: If using an Airport Express to extend the wireless internet capabilities in a given area ( Internet is provided wirelessly from a pimary Airport Base Station to this Airport Express). Is this airport express able to also share internet/networking abilities through its ethernet port? I hope this is not confusing. I would appreciate your insight and help. Thank you.
    PowerBook    

    Senario: If using an Airport Express to extend the
    wireless internet capabilities in a given area (
    Internet is provided wirelessly from a pimary Airport
    Base Station to this Airport Express). Is this
    airport express able to also share
    internet/networking abilities through its ethernet
    port?
    Yes.
    iFelix

  • Airport Express ethernet port for printing?

    I've recently purchased an Extreme (802.11n) for my wireless internet service which is working just fine on its own. In the other room I've set up my older Airport Express for only networking my printers. I don't want to hook up the printer to the ethernet ports on the Extreme as it is near my TV and entertainment center. I understand I cannot use a USB hub to connect two printers to the Express, but is it possible to use the Ethernet port on the Express for my Lexmark E240 or any other ethernet ready laser printer?
    Thanks
    Al Powerbook, MacBook   Mac OS X (10.4.10)  

    Hello Jeff Crowell...Welcome to the Apple Discussions!
    I understand I cannot use a USB hub to connect two printers to the Express, but is it possible to use the Ethernet port on the Express for my Lexmark E240 or any other ethernet ready laser printer?
    To activate the Ethernet port on the AirPort Express Base Station (AX), you need to configure it as a Remote Base Station in a Wireless Distribution System (WDS)...
    Wireless Distribution System (WDS) - Remote Base Station Setup
    (Note: To facilitate setting up the Base Station(s), place them in near proximity of each other during the set up phase.)
    Either connect to the AX's wireless network or temporarily connect directly, using an Ethernet cable, to the Ethernet port of the AX, and then using the AirPort Utility (in Manual Mode) to make the following settings:
    AirPort - Wireless tab
    - Wireless Mode: Participate in a WDS network
    - Network Name: <existing AirPort Network Name>
    - Radio Mode: 802.11b/g compatible
    - Channel: 1
    - Wireless Security: None
    AirPort - WDS tab
    - WDS Mode: WDS remote
    - Allow wireless clients (enabled)
    - WDS Main: <MAC address of the Main Base Station>
    Internet - Internet Connection tab
    - Connect Using: AirPort (WDS)
    - Configure IPv4: Using DHCP
    - Ethernet WAN Port: Automatic (Default)
    - Connection Sharing: Off (Bridge Mode)

  • Sharing Ethernet port

    I'm on a wireless network and have a SIP phone in the office: On my, soon to be retired, Powerbook G4 (in OS 10.2.8) All I had to do to get the phone to work was check share this internet connection in the network control panel. The mac then established itself as a DHCP server for the ethernet port and routed my phone traffic over the wifi (airport)
    On my MacBook Pro (OS 10.4.9) the options have changed slightly: The options seem to make perfect sense: I am sharing my connection from the Airport card to the ethernet. only problem: It doesn't work. I don't have the firewall turned on (although I'd rather change this) just to avoid a conflict. What am I doing wrong?
    PS: I seem to have way too much routing going on by what netstat is reporting but then I can't really read NetStat reports; This is not so much a case of being IP ignorant (although I'm no Guru) as it is not having any reference materials for netstat codes. Can someone direct me on how to read a netstat report?

    The portable has to hand out DHCP addies to anything that wishes to share it's connection, it simply must.
    The G5 will not be getting a DHCP addy from the Wireless LAN via Ethernet, the portable is the go between, and it's the only one that needs to get an addy from the router.
    A possible scenario...
    Portable gets IP of 10.0.1.2 from Router 10.0.1.1, G5 will have a Router setting of 10.0.1.2, (the portable), and gets a pseudo IP of 10.0.2.3 from the pseudo Router 10.0.1.2, (the portable), with the portable translating where the two different base packets go to/from.
    "Is there anyway to see if THE PORTABLE is a DHCP server ?
    Yes, if the Portable is set to "share" it's Internet Connection, then it will be a DHCP Server, pure and simple.
    And can it be truned off?
    Yes, very easily... turn off Internet Sharing".
    Is there a GUI to manage DHCP or is it throught config files?"
    Depends what/how you want to manipulate them, but the only thing you need to do with it ... is GUI via Sharing & Internet.
    The G5 just needs to Join the portables advertised network to get connected, iirc.

  • Is this Ethernet port toast?

    White Intel iMac with built-in iSight, running 10.4.11.
    Client complained of slow network. Stuck a Powerbook on her cable, ran nice and fast. Activity Monitor showed nothing suspicious. The usual voodoo of repair disk & repair permissions changed nothing.
    Booted from a virgin system on an external drive. Console showed the following during a network file copy:
    kernel[0]: AppleYukon: bac packet received, length {various}, packet status bits: CRC error
    Maybe 5% of these said "MII error" instead of CRC error; another 5% showed no status bits.
    Copy ran real slow. Switched over to wireless network over Airport, errors went away, actually ran faster. Stuck cable into Powerbook, did same copy, went fast with no logged errors.
    Is this Ethernet port toast?

    I've never seen a NIC take a hit that slowed it down rather than fried it. I suppose you've eyeballed the port and don't see a bent pin, corrosion, etc.
    I'm thinking configuration or OS rather than hardware. Can you (have you) boot(ed) the computer from another OS or tried a test account to see if that made any difference?

  • Mini ethernet port as a solution to imac dead ethernet port

    I have an old imac 2002 version and it works great but the ethernet port is dead ...not sure why...but I have checked the cables and connections with another computer and they are fine...So assuming that the port is dead
    Can I purchase a mini and use the ethernet port as my connection to the internet via dsl modem and still use my imac...what I'm wondering is can the mini act as a second hard drive and can I network it to my imac via firewire and the use the etherport from the mini to get on the internet....directing it all through my imac?
    I have been told in order to get my imac to connect with a dead ethernet port I need to purchase a new motherboard. That seems like a simple solution...but my imac works great except the ethernet...so if I can find a solution that will just offer me a ethernet connection to the internet and still let me use my imac and give me more memory ...all the better...
    I am not well versed on the mini....So I need some expert advise as to whether it could be a alternative solution...that would also give me additional harddrive.
    Help!

    Yes indeed. Your plan will work (I have done similar with mini/powerbook and powermac).
    In a nutshell - set up the new mini to use the ethernet. Once the network is running, go to Sharing preference pane and select the internet "tab". Choose to share the Built-In Ethernet with the Built-in Firewire - and click start.
    Then connect the mini to the iMac with a firewire cable. Set the iMac to use firewire for its network.
    The only possible gotcha is if you are not on the latest OS (this should work back a version or two - but I don't recall when I first did this). Second gotcha might be the firewall on the mini. You may have to enable logging to see if the firewall is preventing the iMac to connect in and through to the internet. If so - you have to live with opening up some ports on your firewall or learn how to configure that one iMac to get in and not the rest of the world (assuming you don't have a router or other firewall device to protect the new mini.)
    Cheers and good luck.

  • Solutions for Broken Ethernet Port

    The ethernet connector is broken and I'm unable to connect to the ethernet using an ethernet cable. Is there any solution other than replacing the whole motherboard??
    I can't set up any internet connectivity without using the ethernet port...or can I?

    With a wireless modem and/or router and an original AirPort Card, you could enjoy wireless internet.
    It would be easier and cheaper than replacing the logic board.
    The iBook is AirPort-ready.
    Instructions for installing the card can be found in this Apple Knowledge Base article:
    http://docs.info.apple.com/article.html?artnum=111919
    Possible sources for the original AirPort Card (links checked today, priced low to high):
    http://www.synaptech.com/catalog/index.php?mainpage=index&cPath=4953
    http://www.dvwarehouse.com/Apple-Original-AirPort-Wireless-Card-802.11B-p-31366. html
    http://www.megamacs.com/v1/?action=view&pid=967052
    http://www.teksale.com/laptops/laptopparts/listings/apple-airport-original.htm
    http://eshop.macsales.com/item/Apple/M7600LLE/
    http://www.macofalltrades.com/AppleOriginal_Airport_Card_APp/airport1.htm
    http://www.macrecycling.com/apple-airport-card-ibook-g3g4-powerbook-g4-p-100531. html
    http://www.powerbookguy.com/xcart/catalog/Airport-Cards-price0-p-1-c-507.html
    http://store.airportcardsdirect.com/
    http://www.expercom.com/productdetail.html?PRODUCTID=305851
    http://www.ifixit.com/cart/catalog/product98_AirportCard.html
    http://techrestore.com/xcart/product.php?productid=16174
    http://www.lacomputercompany.com/cgi-bin/rpcart/index.cgi?command=dispitem&type= sku&sku=10061
    http://www.welovemacs.com/ibkap.html
    The AirPort Extreme Card is NOT compatible with an iBook G3, and can further damage the logic board if it is installed.
    Good luck.

  • Question about Ethernet Port

    Fumbling in the dark, I knocked by 12" G4 off the table. It must have landed where the ethernet cable connects to the port. I'm now unable to access the network using ethernet. Everything else works okay -- I can use wifi, and all the applications work normally. The reason I use ethernet is because once in a while my wifi connection drops (due to a baby monitor nearby?).
    Do you think this would be a simple fix, or should I bring it in to a shop? My husband is pretty handy with computers and has torn his old G3 apart several times.

    Nancy: This is probably going to require replacing the logic board, to which the Ethernet port is (was) soldered. It's a difficult job, and the part will cost $200-300 used.
    http://www.ifixit.com/Guide/Repair/Installing-PowerBook-G4-Aluminum-12-Inch-1-1- 5-GHz-Logic-Board/553/1

  • Cannot share wireless network through ethernet port??

    I have not been able to get it to work.. 1.5 g4 powerbook ..My ethernet port does not seem to be sending out IPs.. I was able to do this with my dads 867.. i dont understand why its not working?? I go in the contol panels and click on sharing and go through the steps.. still nothing.. is anyone else having problems getting this to work??? i know its a rare config..

    I have a problem similar to yours
    I have tried everything to figure out why the ethernet connection never works on this new used computer. It is able to connect over the airport with the other computer, but that connection is too slow, so I would like to use the ethernet. The computers don't see eachother.
    I use the same ethernet cable to connect my other computer (500 MHz PowerPC G4) to the airport base. I use it to connect my ibook to the G4, It always works. But it has never worked once with this iMac.
    I have made sure filesharing is on, I tried not using firewall at all, appletalk is on and set for ethernet. I have tried other little things and nothing has helped. The only thing I haven't tried yet is getting a new cable. But it works with everything else, so I don't beleive that will help. Is it possible that this new used iMac doesn't have a working ethernet port? I would ask the previous owner but he died.

  • How do I add an airport extreme to a cable modem with only one ethernet port, while keeping that port connected to my Mac?

    I have a mac pro connected by ethernet to a cable modem via ethernet.    There is only one ethernet port on the modem.   
    I want to keep the Mac connected via ethernet for speed.    Is there a way that I can add an airport extreme to this set up - for my ipad and roku, and for guests to use - or do I need to buy a router to put between the modem and the mac?
    If I need a router, what kind?
    Thanks.

    The modem connects to the WAN "O" port on an AirPort Extreme router.
    The Mac Pro connects to one of the three LAN <-> ports on the AirPort Extreme router.
    Or if you do not need the ability to connect a hard drive to the USB port on the router, you can save a bit by using an AirPort Express.
    The modem connects to the WAN "O" port, the Mac Pro connects to the LAN <-> port
    Either the AirPort Extreme router or AirPort Express router will allow up to 50 wireless device to connect.
    There are many other wireless modems offered by other manufacturers as well.

Maybe you are looking for