Problem setting up 2 interfaces against the same destination
Hi,
I've been trying to to configure one SunFire v240 with two extra ethernet interfaces. I can configure it but all traffic (at least outgoing) still uses only one of the interfaces.
I can ping both interfaces from another machine. But if I unplug one cable both interfaces are unreachable.
I did the following to setup the interfaces:
ifconfig bge1 unplumb
ifconfig bge1 plumb
ifconfig bge1 192.168.10.101 netmask 255.255.255.0 broadcast 192.168.10.255 up
ifconfig bge2 unplumb
ifconfig bge2 plumb
ifconfig bge2 192.168.10.102 netmask 255.255.255.0 broadcast 192.168.10.255 up
netstat -rnRouting Table: IPv4
Destination Gateway Flags Ref Use Interface
192.168.10.0 192.168.10.101 U 1 698265 bge1
192.168.10.0 192.168.10.102 U 1 0 bge2
136.225.115.0 136.225.115.159 U 1 9602 bge0
224.0.0.0 136.225.115.159 U 1 0 bge0
default 136.225.115.2 UG 1 13026
127.0.0.1 127.0.0.1 UH 301081627713 lo0
uname -aSunOS v240x763 5.9 Generic_118558-14 sun4u sparc SUNW,Sun-Fire-V240
ifconfig -alo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 136.225.115.159 netmask ffffff00 broadcast 136.225.115.255
bge1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 7
inet 192.168.10.101 netmask ffffff00 broadcast 192.168.10.255
bge2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 8
inet 192.168.10.102 netmask ffffff00 broadcast 192.168.10.255
>
Is there any known problem with this setup?
Best Regards,
Christer
This is due to the routing tables, which in your case
specifies that all data that heads for the
192.168.10.0 network will be sent out through bge1.Correct.
If you want to use both interfaces when sending data,
you have to trunk them.IPMP is also supported.
It seems very strange that both interfaces gets
unreachable if you disconnect one cable.As you mentioned. The interface itself isn't really unreachable. But the reply to any traffic tries to use the other interface so it isn't useable.
Darren
Similar Messages
-
Problem importing two service interfaces using the same data types
Hi,
I've been playing around with BPM for a while. Now I wanted to add a custom service interface to my starting event. I created the interface in ESR of CE 7.11. After importing I get this error message and I can't use the interface:
Cannot change XsdSimpleTypeDefinition AcademicTitleCodeContent by importing the document http://sap.com/xi/APPL/SE/Global::src/wsdl/TestInterface.wsdl, because it is already defined in the document http://sap.com/xi/APPL/SE/Global::src/wsdl/rootwsdl_CustomerERPByIDQueryResponse_InService.wsdl in this project. Importing into another project might be possible.
Of course the problem is clear, but how can I achieve importing two service interfaces that use the same data type without changing the xsd source?
Thanks in advance,
ManeSorry for the late answer, but I am really busy at the moment.
Unfortunately I can't the Interface and data types are already changed.
But this happened various times. Each time I already had imported a SAP Enterprise Service into NW BPM that contains a bunch of inline data types. While creating my own interface I referenced one of those data types that are stored in a SAP namespace. After import the error message appeared.
In the wsdl of the created interface there is a import statement for the namespace where the referenced data types origin from. Additionally there is a namespace definition xmlns:p1="SAPnamespace". In the element the type is "p1:ReferencedType". Could this maybe cause the error, because one time it is with this leading p1 in my created wsdl and once without in the SAP Service wsdl?
Thanks and I am looking forward to next EhP of NW BPM,
Mane -
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN .
HI All,
I have a Problem with Romming Between SSIDs withing the same WLC but with deferent VLAN . the WLC are providing the HQ and one of the Branches the Wireless services .
Am using all the available 9 SSIDs at the HQ , and am using only 4 of it at the Brnche.
The problem that i have are happening only at the Branch office as i cant room between the SSIDs within Diferent VLANs but i can do it with the one that pointing to the same VLAN. Once the client ( Laptop/Phone ) connected to one of the SSIDs. it imposiible to have him connected to the other ones with Different VLAN. meanwhile, It says its connected to the other SSID but its not getting IP from that pool.
here is the Show Run-Config from my WLC .. and the Problem happening between the SSID AMOBILE and ASTAFF. i have the Debug while am switching between the SSIDs if needed .
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2013.11.04 10:20:47 =~=~=~=~=~=~=~=~=~=~=~=
show run-config
Press Enter to continue...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 5500 Series Wireless LAN Controller"
PID: AIR-CT5508-K9, VID: V01, SN: FCW1535L01G
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.0.235.0
Bootloader Version............................... 1.0.1
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.3, Env 1.6, USB console 1.27
Build Type....................................... DATA + WPS
System Name...................................... WLAN Controller 5508
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
IP Address....................................... 10.125.18.15
Last Reset....................................... Software reset
System Up Time................................... 41 days 5 hrs 14 mins 42 secs
System Timezone Location......................... (GMT -5:00) Eastern Time (US and Canada)
Current Boot License Level....................... base
Current Boot License Type........................ Permanent
Next Boot License Level.......................... base
Next Boot License Type........................... Permanent
Configured Country............................... US - United States
--More or (q)uit current module or <ctrl-z> to abort
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +36 C
External Temperature............................. +20 C
Fan Status....................................... OK
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 10
Number of Active Clients......................... 61
Burned-in MAC Address............................ 30:E4:DB:1B:99:80
Power Supply 1................................... Present, OK
Power Supply 2................................... Absent
Maximum number of APs supported.................. 12
Press Enter to continue or <ctrl-z> to abort
AP Bundle Information
Primary AP Image Size
ap3g1 5804
ap801 5192
ap802 5232
c1100 3096
c1130 4972
c1140 4992
c1200 3364
c1240 4812
c1250 5512
c1310 3136
c1520 6412
c3201 4324
c602i 3716
Secondary AP Image Size
ap801 4964
c1100 3036
--More or (q)uit current module or <ctrl-z> to abort
c1130 4884
c1140 4492
c1200 3316
c1240 4712
c1250 5064
c1310 3084
c1520 5244
c3201 4264
Press Enter to continue or <ctrl-z> to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or <ctrl-z> to abort
Network Information
RF-Network Name............................. OGR
Web Mode.................................... Disable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Enable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Unicast
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
--More or (q)uit current module or <ctrl-z> to abort
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Fast SSID Change ........................... Enabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
Press Enter to continue or <ctrl-z> to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
2 Normal Disa Enable Auto Auto Down Enable N/A Not Present
3 Normal Disa Enable Auto Auto Down Enable N/A Not Present
4 Normal Disa Enable Auto Auto Down Enable N/A Not Present
5 Normal Disa Enable Auto Auto Down Enable N/A Not Present
6 Normal Disa Enable Auto Auto Down Enable N/A Not Present
7 Normal Disa Enable Auto Auto Down Enable N/A Not Present
8 Normal Disa Enable Auto Auto Down Enable N/A Not Present
Press Enter to continue or <ctrl-z> to abort
AP Summary
Number of APs.................................... 8
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
KNOWLOGY_DC01 disabled -
KNOWLOGY_DC02 disabled -
--More or (q)uit current module or <ctrl-z> to abort
KN1252_AP01 disabled -
KN1252_AP02 disabled -
Anham_AP03 disabled -
ANHAM_AP01 disabled -
ANHAM_AP04 disabled -
ANHAM_AP02 disabled -
Press Enter to continue or <ctrl-z> to abort
AP Location
Total Number of AP Groups........................ 3
Site Name........................................ ANHAM8075
Site Description................................. ANHAM 8075 Location
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Anham_AP03 2 AIR-LAP1142N-A-K9 70:81:05:88:15:b5 default location 1 US 1
ANHAM_AP01 2 AIR-LAP1142N-A-K9 70:81:05:b0:e4:62 Small Conference 1 US 1
ANHAM_AP04 2 AIR-LAP1131AG-A-K9 00:1d:45:86:e1:b8 Conference room 1 US 1
ANHAM_AP02 2 AIR-LAP1142N-A-K9 70:81:05:96:7a:49 Copy Room 1 US 1
Site Name........................................ Knowlogy_DC
--More or (q)uit current module or <ctrl-z> to abort
Site Description................................. DC Center Access points
WLAN ID Interface Network Admission Control Radio Policy
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KNOWLOGY_DC01 2 AIR-LAP1131AG-A-K9 00:1d:45:86:ed:4e KNOWLOGY_DC_Serv 1 US 1
KNOWLOGY_DC02 2 AIR-LAP1131AG-A-K9 00:21:d8:36:c5:c4 KNOWLOGY_DC_Serv 1 US 1
Site Name........................................ OGR
Site Description................................. 1934 OGR Office
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
7 knowlogy_ogr Disabled None
9 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
KN1252_AP01 2 AIR-LAP1252AG-A-K9 00:21:d8:ef:06:50 Knowlogy Confere 1 US 1
KN1252_AP02 2 AIR-LAP1252AG-A-K9 00:22:55:8e:2e:d4 Server Room Side 1 US 1
Site Name........................................ default-group
Site Description................................. <none>
WLAN ID Interface Network Admission Control Radio Policy
1 knowlogy_ogr Disabled None
2 knowlogy_ogr Disabled None
3 knowlogy_ogr Disabled None
4 knowlogy_ogr Disabled None
5 knowlogy_ogr Disabled None
6 knowlogy_ogr Disabled None
7 knowlogy_ogr Disabled None
8 knowlogy_ogr Disabled None
--More or (q)uit current module or <ctrl-z> to abort
9 knowlogy_ogr Disabled None
10 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
Press Enter to continue or <ctrl-z> to abort
AP Config
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch IP Address.................. 10.125.18.15
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abortIP Address.................. 10.125.18.15
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
--More or (q)uit current module or <ctrl-z> to abort
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or <ctrl-z> to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 6
Cisco AP Name.................................... KNOWLOGY_DC01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:86:ed:4e
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.100
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................ wireless.knowlogy.com
Primary Cisco Switch Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1134T0QG
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 19 m 18 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:33 2013
Join Taken Time.................................. 0 days, 00 h 10 m 47 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:71:09:8f:90
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 44
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
--More or (q)uit current module or <ctrl-z> to abort
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
--More or (q)uit current module or <ctrl-z> to abort
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211b
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
--More or (q)uit current module or <ctrl-z> to abort
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
--More or (q)uit current module or <ctrl-z> to abort
Current Tx Power Level .................... 1
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or <ctrl-z> to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... KNOWLOGY_DC02
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:36:c5:c4
IP Address Configuration......................... DHCP
IP Address....................................... 10.22.1.101
Gateway IP Addr.................................. 10.22.1.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ KNOWLOGY_DC_ServerRoom
--More or (q)uit current module or <ctrl-z> to abort
Cisco AP Group Name.............................. Knowlogy_DC
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.3.8.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Enabled
PoE Power Injector MAC Addr...................... Disabled
--More or (q)uit current module or <ctrl-z> to abort
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1131AG-A-K9
AP Image......................................... C1130-K9W8-M
IOS Version...................................... 12.4(23c)JA5
Reset Button..................................... Enabled
AP Serial Number................................. FTX1230T24F
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 22
WLAN 2 :........................................ 21
WLAN 4 :........................................ 25
WLAN 3 :........................................ 25
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or <ctrl-z> to abort
AP Up Time....................................... 48 days, 20 h 24 m 41 s
AP LWAPP Up Time................................. 40 days, 13 h 58 m 18 s
Join Date and Time............................... Tue Sep 24 21:24:35 2013
Join Taken Time.................................. 0 days, 00 h 10 m 48 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 3
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:a5:0c:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 20
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or <ctrl-z> to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 15 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140,
......................................... 149,153,157,161
TI Threshold .............................. -50
Antenna Type............................... INTERNAL_ANTENNA
Internal Antenna Gain (in .5 dBi units).... 8
--More or (q)uit current module or <ctrl-z> to abort
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Press Enter to continue or <ctrl-z> to abort
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... KN1252_AP01
Country code..................................... US - United States
Regulatory Domain allowed by Country............. 802.11bg:-A 802.11a:-A
AP Country code.................................. US - United States
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:21:d8:ef:06:50
IP Address Configuration......................... DHCP
IP Address....................................... 10.125.18.101
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 10.125.18.1
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Enabled
Ssh State........................................ Disabled
Cisco AP Location................................ Knowlogy Conference Rooms Side
Cisco AP Group Name.............................. OGR
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or <ctrl-z> to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... H-Reap
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.0.235.0
Boot Version ................................... 12.4.10.0
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. PoE/Medium Power (15.4 W)
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1252AG-A-K9
AP Image......................................... C1250-K9W8-M
IOS Version...................................... 12.4(23c)JA5
--More or (q)uit current module or <ctrl-z> to abort
Reset Button..................................... Enabled
AP Serial Number................................. FTX122990L5
AP Certificate Type.............................. Manufacture Installed
H-REAP Vlan mode :............................... Enabled
Native ID :..................................... 118
WLAN 1 :........................................ 111
WLAN 2 :........................................ 111
WLAN 4 :........................................ 112
WLAN 6 :........................................ 112
WLAN 7 :........................................ 111
WLAN 9 :........................................ 112
WLAN 8 :........................................ 112
H-REAP Backup Auth Radius Servers :
Static Primary Radius Server.................... Disabled
Static Secondary Radius Server.................. Disabled
Group Primary Radius Server..................... Disabled
Group Secondary Radius Server................... Disabled
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 26 days, 00 h 24 m 39 s
--More or (q)uit current module or <ctrl-z> to abort
AP LWAPP Up Time................................. 26 days, 00 h 23 m 48 s
Join Date and Time............................... Wed Oct 9 10:59:07 2013
Join Taken Time.................................. 0 days, 00 h 00 m 50 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 7
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:22:55:df:a5:90
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
--More or (q)uit current module or <ctrl-z> to abort
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... SUPPORTED
MCS 1.................................... SUPPORTED
MCS 2.................................... SUPPORTED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
--More or (q)uit current module or <ctrl-z> to abort
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 ..........Well you need to understand the behavior of h-reap or what it's called now, FlexConnect. In this mode, the clients are still remembers on the WLC until the session timer/idle timer expires. So switching between SSID's in h-reap will not be the same when switching when the AP's are in local mode.
Take a look at the client when connected in FlexConnect in the WLC GUI monitor tab. Thus will show you what ssid and vlan the client is on. Now switch to a different ssid and compare this. It's probably the same because the client has not timed out. Now go back to the other ssid and look again. Now on the WLC, remove or delete the client and then switch to the other ssid at the same time. Or switch SSID's and then remove the client. The client will join the new ssid and in the monitor tab, you should see the info.
There is no need to have clients have multiple SSID's unless your testing. Devices should only have one ssid profile configured to eliminate any connectivity issues from the device wanting to switch SSID's.
Sent from Cisco Technical Support iPhone App -
WLC-2106 and multiple interfaces on the same network
Hi there,
I recently created a TAC request to the Cisco support regarding our WLC-2106, but they could not help me. Basically I just learned that you can create new interfaces for the wireless LAN controller and then dedicate them to a given wireless network (SSID). This way I could more effectively utilize network bandwidth also. Problem is that all of the interfaces have to be in a different network segment in order to work, which is not what I want. I specifically want to have several interfaces on the same network segment.
Has anyone tried to accomplish the same?Basically what I've misunderstood is that all the traffic generated by our wireless clients have been going through the single 100Mbit/s ethernet port on the wireless LAN controller (management interface), and to mitigate this I thought I could create new interfaces (ports) and dedicate those to given WLAN networks.. I see now that this is not supported. Not inside the same network at least.
So, by reading further and consulting my best friend Google I learned about a setting called "AP Mode". Changing that from Local (the default) to H-REAP the APs should not route their traffic anymore through the management interface on the wireless controller, but instead route all the client traffic directly to the local LAN. This way you effectively remove the 100Mbit/s bottle-neck when all the APs were using the management interface both for configuration and client data traffic.
It seems you also have to enable H-REAP Local switching from a given WLAN network in addition to changing the AP Mode of your access points to H-REAP. I'm still in the testing phase here so should anyone have any insight to this, I'd be greatful to hear more. -
What is the best way to set up multiple devices in the same household?
Our family has a bunch of devices (phones,pads,pods) all set up under the same appleID. The idea was to be able to share iTunes content among devices. The problem is that there is personalized data merging between devices (address book, apps, etc). Is there a way to set up multiple devices under the same account while maintaining their own identity so that Each user can have their own apps, addresses, etc without having to sift through everyone else's stuff?
Continue to share your iTunes ID, but use different IDs for other services such as FaceTime, iMessage and iCloud. (When you share the same iCloud account across multiple devices, any synced data is merged and the merged list appears on all devices sharing the account.)
To change the ID For:
iMessage, go to Settings>Messages>Send & Receive (Receive At in iOS 5), tap the ID sign out, sign back in using the other ID.
FaceTime, do the same thing in Settings>FaceTime.
iCloud, you'll have to delete the account, create a new account with the other ID, and migrate your data to the new account. Before deleting the account, if you have any photos in photo stream that are not in your camera roll or backed up somewhere else save these to your camera roll or you will lose them. To do this, open the photo stream album in the thumbnail view, tap Edit, tap all the photos you want to save, tap Share, then tap Save to Camera Roll. Once this is done, go to Settings>iCloud, scroll to the bottom and tap Delete Account. When prompted about what to do with the iCloud data, be sure to select Keep On [iDevice]. Next, set up a new iCloud account using a different Apple ID (if you don't have one, tap Get a Free Apple ID at the bottom). Then turn iCloud data syncing for contacts, etc. back to On, and when prompted about merging with iCloud, choose Merge. This will upload the data to the new account. Finally, to un-merge the data you will then have to go to icloud.com on your computer and sign into each iCloud account separately and manually delete the data you don't want in each account (such as deleting the other person's contacts from your account, and vice versa).
This article may be of interest: http://www.macstories.net/stories/ios-5-icloud-tips-sharing-an-apple-id-with-you r-family/. -
Can you run Edirol / Focusrite firewire interfaces at the same time?
Hey Guys,
I have an Edirol FA-101 but i'm just about to get a Focusrite Saffire (or maybe a Motu 8pre...haven't decided yet) and was wondering if I can run the 2 interfaces at the same time for more inputs...i know i can chain 2 of the edirol ones but i'm not sure if it works with different makes.
Thanksso I actually did get myself a focusrite saffire pro 26 and it's pretty cool (apart from the focusrite computer side interface that seems to have a few bugs when you control by hardware...)
I'm probably gonna get myself an octopre or a twintrack pro to make use of at least some of the extra digital inputs but for now I have the semi redundant Edirol FA-101 in my rack, if I can get the two working together then that's great!
I have tried what you said and it did pair them together however it made a really awful noise when trying to record, just intense digital distortion and i'm not really sure why. I'm running it all from a macbook pro with only one FW port (that has the Saffire / Edirol / FW Hard drive / Liquid Mix running from it in that order) do you think this order is more the problem?
Dave -
Can i set up my ipad in the same itouch account?
can i set my new ipad in the same account/place where i currently have my itouch set up? will this affect what i currently have in my itouch or will it see the difference when i connect my ipad and itouch? thank you
You can use the same account and iTunes library with both - iTunes will recognise that it's a different device and you can then chose what to sync or not to sync. I use my iPad, iPhone, and iPod Touch on the same computer without any problem.
-
Tolerance/verificat. of price entering several invoices against the same PO
Hi!
I'm having some troubles when trying to check the price verification at the MIRO.
I'd like to be able to check the price verification when doing several invoices against the same PO;
not allowing the total amount entered in all the invoices to be greater than the PO they refer to.
I give you an example:
I have a PO of only one line of 100eur. and a tolerance of 5%.
Also a Invoice against this PO of 50eur.
If i try to do another Invoice against the same PO, the maximum price allowed should be 55eur.
Could anyone help me?
Thanks in advance!Thanks for your answer Prabu,
But my problem is still unsolved.
I've checked the tolerance limits in the SPRO, and if I have one Invoice against one PO, all works properly.
The issue is when having several Invoices against the same PO.
The system checks the limits against the price of the PO, not taking account of the previous invoices that PO has.
In the example above:
- PO: 100eur. Tolerance of 5%.
- 1st Invoice. 50eur against the PO.
- 2nd Invoice. The maximun price allowed is 105eur (100eur from the PO + 5eur of tolerance).
But the price of the 1st Invoice should be subtracted ( 100eur from the PO + 5eur of tolerance - 50eur from the 1st Invoice) , that is the maximum price allowed should be 55eur.
Thanks anyway! -
Hi,
I have another problem - after upgrade ios wirelles connection not work.
After reload i have :
Configuration of subinterfaces and main interface
within the same bridge group is not permitted
STP: Unable to get the port parameters.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
Please configure the bridge group on this interface first.
SETUP: new interface NVI0 placed in "shutdown" state
my old configuration work propertly in the old software, but after update i have notificatio.
Old thread:
https://supportforums.cisco.com/discussion/12379491/cisco-877w-no-wireless-connection
my current sh run:
version 12.4
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime
service timestamps log datetime msec localtime
service password-encryption
hostname cisco
boot-start-marker
boot system flash:c870-advipservicesk9-mz.124-24.T6.bin
boot-end-marker
logging message-counter syslog
logging buffered 4096 informational
enable secret 5 $1$eCNp$rWuBfZ/cexnwnkm7L447s.
aaa new-model
aaa session-id common
dot11 syslog
dot11 ssid ciscowifi
vlan 1
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 050D031D26595D0617
dot11 wpa handshake timeout 500
ip source-route
no ip dhcp use vrf connected
ip dhcp excluded-address 192.168.56.1
ip dhcp pool CLIENT
import all
network 192.168.56.0 255.255.255.0
default-router 192.168.56.1
dns-server 8.8.8.8 194.204.159.1 194.204.152.34
lease 0 2
ip cef
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
username marek password 7 00121A0908500A
archive
log config
hidekeys
ip tcp path-mtu-discovery
bridge irb
interface ATM0
description Polaczenie ADSL do ISP$ES_WAN$
no ip address
no atm ilmi-keepalive
pvc 0/35
encapsulation aal5mux ppp dialer
dialer pool-member 1
hold-queue 224 in
interface FastEthernet0
description Edzia
interface FastEthernet1
description dom
interface FastEthernet2
description Dziadek
interface FastEthernet3
interface Dot11Radio0
no ip address
no ip redirects
ip local-proxy-arp
ip nat inside
ip virtual-reassembly
no dot11 extension aironet
encryption vlan 1 mode ciphers tkip
encryption mode ciphers aes-ccm tkip
broadcast-key change 3600
ssid ciscowifi
speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role root
world-mode dot11d country AU indoor
no cdp enable
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1
description ciscowifi
encapsulation dot1Q 1 native
no cdp enable
interface Vlan1
no ip address
bridge-group 1
interface Dialer0
description Interfejs dzwoniacy
ip address negotiated
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
dialer-group 1
ppp chap hostname [email protected]
ppp chap password 7 xxxxxxxxxxxxxxxxxxxxxx
interface BVI1
description Polaczenie dla sieci LAN
ip address 192.168.56.1 255.255.255.0
ip nat inside
ip virtual-reassembly
no ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer0
no ip http server
no ip http secure-server
ip nat inside source list 100 interface Dialer0 overload
ip nat inside source static tcp 192.168.56.10 80 interface Dialer0 80
ip nat inside source static tcp 192.168.56.10 22 interface Dialer0 22
logging trap debugging
logging 192.168.56.10
access-list 100 permit ip 192.168.56.0 0.0.0.255 any
access-list 100 deny ip any any
no cdp run
snmp-server community ciskacz RO
snmp-server chassis-id ciskacz
control-plane
bridge 1 protocol ieee
bridge 1 route ip
line con 0
no modem enable
line aux 0
line vty 0 4
exec-timeout 0 0
transport preferred ssh
transport input ssh
scheduler max-task-time 5000
end
please help - thanks!Hello Marek,
I suppose you are not planning to do any kinds of advanced config using several VLANs and multiple SSIDs so let's just make your configuration simple and working.
In short, you need to remove all references to VLAN 1 and to any subinterfaces possibly related to the VLAN 1. This means in particular (follow these steps in sequence):
Remove the Dot11Radio0.1 subinterface entirely
In the Dot11Radio0 section, remove the encryption vlan 1 mode ciphers tkip command
In the dot11 ssid ciscowifi section, remove the vlan 1 command
After performing these steps, make sure that the ssid ciscowifi and encryption mode commands are still present in the Dot11Radio0 configuration, and if not, reenter them.
Best regards,
Peter -
ACE bridge and routed interface in the same context
/* Style Definitions */
table.MsoNormalTable
{mso-style-name:Standardowy;
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hello
I am wondering if it is possible to configure one ACE context to support both routed and bridge interface?
I would like to have a bridge-mode context but in the same time I would like to have a separated OOB interface for management.
If it is possible how they could interact to each other?
Thank you in advance for any answer
Regards
Lukasz/* Style Definitions */
table.MsoNormalTable
{mso-style-name:Standardowy;
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-parent:"";
mso-padding-alt:0cm 5.4pt 0cm 5.4pt;
mso-para-margin:0cm;
mso-para-margin-bottom:.0001pt;
mso-pagination:widow-orphan;
font-size:10.0pt;
font-family:"Times New Roman";
mso-ansi-language:#0400;
mso-fareast-language:#0400;
mso-bidi-language:#0400;}
Hello
We've just tried to configure bridged and routed interfaces at the same time in the lab and we've had a problem.
When we added the def gw for the bridged config we noticed that we had an issue with the traffic src by the rservers in the routed config.
When we deleted the new def gw, the problem disappeared.
I am attaching the lab config.
When we added to it the following line
ip route 0.0.0.0 0.0.0.0 10.1.1.163
reals B1-B10 could not communicate to the outside world.
Do you know why it does not worked and what could we do to fix it ?
Thank you in advance.
Regards
Lukas -
Use two interfaces on the same network
Hello every one,
I actually starting to work on a cisco project. I'm a beginner on networking and cisco technologie.
For my project we use a router 2921.
We got two network:
- Network A: 192.198.0.X / 255.255.255.0 / Gateway 192.198.0.1
- Network B: 162.168.0.X / 255.255.0.0 / Gateway 162.168.0.1
Each network use switch, Switch A (connecting to network A) is connected to interface G0/0.
And Switch B (connecting to network B) is connected to interface G0/1.
Router well configured as:
- G0/0: ip address 192.198.0.1 255.255.255.0 (network A)
- G0/1: ip address 162.168.0.1 255.255.0.0 (network B)
Every think working fine.
The problem is with this one, we need to connect a computer on G0/2. This computer is configure as network A (192.198.0.10 / 255.255.255.0 and same gateway).
I can't configure G0/2 as 192.198.0.1 255.255.255.0 (network A), cause G0/0 use this adresse.
I can't put this computer on the switch A, my only physical possibilité is to connect him on G0/2.
We just need to use interface G0/0 and G0/2 as a switch on the router with the same gateway (192.198.0.1)
How can i connect this computeur? How can i configure two interfaces on the same network and same gateway?
Thanks youI would just put the PC on a different network, but if you really want it to be in the same network, you could use IRB to connect two of the interfaces on the router at layer 2.
Here is an example config for IRB:
interface FastEthernet0/0
bridge-group 1
interface FastEthernet0/1
bridge-group 1
bridge irb
interface BVI1
ip address 192.168.0.1 255.255.255.0
bridge 1 route ip
Notice that the physical ports do not have IP addresses on them, the IP for the subnet is on the BVI interface. -
How can I set up two iPhones with the same contact, photos, music etc... but a different sim card and phone number. They will both be my phones, but one will be for use in other countries.
Phone A = phone with information you want duplicated
Phone B = phone that you want to copy from A
Backup Phone A.
Wipe Phone B using these instructions. What to do before selling or giving away your iPhone, iPad, or iPod touch - Apple Support
Phone B should be on the 'Hello' screen. Do not swipe it. Launch iTunes. Plug in Phone B.
When iTunes asks if you want to set up as new phone or restore from backup, choose restore from backup of Phone A.
After this setup, any changes to one phone (i.e. adding a contact, downloading an app) will have to be manually duplicated on the second phone, if that is your desire). Making changes to one phone will not affect the other after setup. -
How to use multiple Interfaces for the same BS?
Hi @ ,
Is it possible to have a scenarion where i am using multiple interfaces in the same BS based upon some conditional field in the message.
I amnot able to get the solution I know with condition editor I can have multiple receivers but in my scenarion based upon message fiels i have to decide which BAPI to be used and wht mapping and then post it to the same System
Any help will be highly rewarded
RegardsHi-
Yes it is possible you can use multimapping for mapping the interfaces.
To know more about multimapping see
http://help.sap.com/saphelp_nw04/helpdata/en/21/6faf35c2d74295a3cb97f6f3ccf43c/content.htm
Some more helpful links
/people/jin.shin/blog/2006/02/07/multi-mapping-without-bpm--yes-it146s-possible -
Posting multiple goods issues against the same delivery
Hello gurus,
We are a fashion apparel company using ECC 6.0 and would like to know if it is possible to post mutliple goods issues against the same delivery?
I will explain the business requirement.
- We create a stock transport order to deliver 400 units of merchandise to on or our retail stores (STO is created and processed to a delivery).
- This information is passed down to our warehouse management system (which is not SAP)
- Our warehouse management system has the ability to split a delivery into multiple shipment when needed. For example, our warehouse may only be able to complete 250 units for our morning shipment and will therefore pick, pack and post this. This will feed back into SAP and process a 641 movement so that the units now show as "in transit". This is needed so that our stores can process the ASN and move the units into their inventory when they receive the merchandise later that day.
- During the afternoon, our warehouse will process the remaining 150 units and will ship this to our store later in the evening or next day.
Currently, we are not able to process another goods issue against a delivery as we close out the delivery during the first goods issue. We would prefer not to have to generate a new delivery for our DC and let them continue to process against the same delivery, but we are unsure how to configure this.
Any help or guideance would be extremely appreciated
Thanks in advanceHi RJ,
First of all sorry to write such a lengthy reply,In one line if i want to summerize then it is not possible with standard SAP however we can achieve this by writing some piece of code in both the system
AS - IS
Business process
From business process point of view you are right that once the pick & pack is in process it is not advisable to create a new delivery document for balance quantity and share the same with WMS as then they have to create a new document in WMS and start picking based on that rather then the old delivery document number. if i am in your position then i can give a thought like this
e.g.
Delivery - 100 Unit
Shipment confirmation from WMS - 60 Unit
Change in delievry quanity / Pick qty - 60 Unit
Invoice from SAP - 60 Unit
Second confirmation from WMS - 40 Unit
Change in the existing delivery quantity - Now here we have two option either
1) Change the delivery quantity / Pick qty to (60+40) =100 or
2) Remove the 60 and update 40 as delivery and pick quantity
Pros & Cons
if you will select option 1 then furhter invoice will happen for 100 unit which is incorrect as physically you are shipping only 40 unit
if you are selecting option 2 then the document flow is incorrect as you don't have history(in SAP) for the 60 unit which was shipped earlier
Solution ::
so in my opinion the best option is to create a seperate delivery document (store the old delviery number in one of the field of the new delivery and pass the same to custom segment of the IDoc) transmit the IDoc to WMS write the validation logic in WMS
Find the record with old deliver number in the WMS system, check the status whether it is active or inactive
if it is acitive Validate the Material + qty with the WMS record(Material + balance quantity) if both are same then pass the new deliery number to custom field of the WMS table
At the time of confirming back to the SAP, Write a piece of code in SAP that if the incoming idoc custom field(new delivery number) field is populated then ignore the orignal document number and post the document using the new delivery document number
Hope this help -
Can you use 2 sets of bluetooth headphones at the same time with the Ipad 4?
Hi, I was wondering if anyone could tell me if I can use 2 sets of bluetooth headphones at the same time with the Ipad?
It is so my children can watch a film or listen to music together.
ThanksNo
Maybe you are looking for
-
Getting Error 500 Internat Server Error when trying to access Mobile App from OBIEE 11.1.1.7.1
Hi Everyone I am getting this error message when I try to open the Mobile App from OBIEE. After I log in to OBIEE, I navigate to New >> click on Mobile App and get this error message: Error 500--Internal Server Error From RFC 2068 Hypertext Transfer
-
Alert Configuration & Mail Alert
Dear All, I have configured the alert configuration using the blog: /people/michal.krawczyk2/blog/2005/09/09/xi-alerts--step-by-step but still I am not getting any error message in the Alert Inbox, eventhough i receive an error message in SXMB_MONI a
-
NOT SOLVED - Border printing problem
Disregard the thread that claims this is fixed -- it is NOT. Same problem with a brand spanking new Office Jet 6500. This is NOT a problem with Word. This is NOT an application problem. This is an HP problem because it is their driver that tells the
-
I have an issue where an application failed to distribute to 1 (EAPSCCM) of our 12 DPs so I removed the content from DP which it failed on as the redistribute option was failing. However now I am not able to distribute the content back onto that DP,
-
Dynamically change Database, Server and Command From VB6
I have a crystal report which connects to an iSeries box via an OLE DB datasource, however i need to have this same report conect to two different iSeries, with the tables for the sql (command) located in two different libraries. Is it possible to ch