Problem with calibration of AT-MIO-16XE-10 card. Using E Series Calibrate VI I get error = -10840, using MIO Calibrate VI I get error = -10029.
The reason I want to calibrate the card is that I am getting a spurious +10mV offset on the analog out channels, and a -60mV offset on the analog in. These offsets first occured after a hard-disk crash, where labview 6.0 was installed along with the new hard-disk. The computer is running window 95.
The correct function to use is E Series Calibrate. In the past, this 10840 error is returned by the E series calibrate function when the EEPROM of the board needs to be reprogrammed. To fix this problem, call customer support to send the board in (http://sine.ni.com/apps/we/niae_asc.main).
If you cannot wait for the board's EEPROM to be reprogrammed, then consider using averaging several datapoints rather than using single datapoints to lessen the offset in your results. There are other sources of bad readings besides the need for calibration. Check out this webpage for more troubleshooting advice:
http://digital.ni.com/public.nsf/websearch/cb279761ae4bc61186256a38005444c6
Similar Messages
-
I am using my Ipad on a remote craftshow site and am having problems with battery lasting 8 hrs. Can I use a 12v rv battery to recharge it or at least maintain the charge over longer periods of time? I have a dc adapter. thanks
You should be able to use the battery if you get a car type charger which recharges mobile devices.
The full size iPads use a 10-12W charger, whereas the mini uses a 5W charger. Many car chargers only supply 5W. But at 5W, the car charger should give you some extra time on your iPad. It would be best to use a 10-12W car charger.
Cheers, Tom -
Problems with ASIO on multiple Audigy 2 ZS cards
G'day,
I've been using an Audigy 2ZS PCI for a couple of years now with great success. I convert old audio recordings to various digital formats using a couple of applications (mainly Adobe Audition 1.5 & 2.0).
Recently, my workload has increased to the point where I needed one card to just record at high res, and another card to handle just playback and general Windows bells & whistles without impacting the performance of the recording.
I installed a second 2ZS, it was detected by Windows, etc, and I set it up so Windows uses one card (identified as A800) for all its stuff, and the second card (B000) is used only for ASIO recording.
That's where the nightmare started. I've uploaded and installed the May 2006 Creative driver update, but I still suffer from a number of problems, some related to Audition, some not.
The least annoying problem is that all the Creative drivers seem to identify only a truncated version of the ID string. So for example, in various applications, I see "SB Audigy 2ZS [B0 -1" or "SB Audigy 2ZS [A8 -5". This is annoying but not showstopping.
The biggest problem is getting applications to correctly interact with the Creative Labs ASIO driver and enumerator. Most applications (Nero, Audition, Premiere Pro) can "see" the ASIO driver, but when it's selected, it may not work at all, or may work from one or the other sound card, without any clear indication of which card is selected.
I'm sorry if this sounds generic, but I've spent a week with the Adobe folks, who simply ended up telling me "it's a problem with the CL drivers", and most forums I frequent say the same thing, and the specifics vary from application to application, but at the core, CL drivers are just not working properly with the system when two cards are installed.
By way of example, using ASIO4ALL has fixed many of the card selection problems, but even there, sometimes the inputs of one card are disabled, sometimes the other card, and in the middle of a recording session (line in jack, 44.1k/16 bit), the input waveform slowly biases down to -2V and then all I get are inverted samples - quiet appears as max. value samples, while valid audio appears as -2V samples! If I put the audio line into the other card, it plays just fine (I know what I'm doing WRT grounding and line levels, etc).
This system has run essentially non-stop since September 2005, and I guess it collected a lot of software crud, so I bit the bullet and performed a clean reinstall of Windows XP and updated every driver I could. Some problems have since changed for the better (i.e. clicking on the configure button of the CL ASIO driver no longer bluescreens or displays an empty window), but the problems described above still happen all the time.
I was wondering if other users have seen the same or similar problems, and if so, what has worked for you?
The system is a Gigabyte 81PE1000Pro2, PCI bus, 3.2GHz P4 with HT enabled, 2G physical RAM, and a 1.5Tb RAID disk system.
Recording when a single sound card (either of the cards works beautifully on its own) is perfect; just when both cards are installed, everything gets confused! Even the WDM drivers don't correctly identify or manage the routing of inputs and outputs reliably.
Sorry to go on about this. If anyone can offer constructive suggestions (I define "constructive" as not telling me to "buy another type of card" or (as one poor soul suggested) telling me that multiple PCI sound cards are not supported under Windows), I would be most grateful.
Thanks and regards,
PeterG'day Jutapa, thanks for looking at this!
Yeah, I got all the possible ASIO drivers listed, one CL ASIO driver is listed for each card, and I have spent much time trying different configurations of card order, I/O port order, direct sound enabling/disabling, timesync enable/disable, etc.
The problem for me with the CL ASIO drivers is that it limits me to 48/96k sampling only. That is not acceptable, because I need to sample at 44.1k for "straight" conversions to CD, or 192k/24-bit for archival purposes (used for extremely old or fragile recordings), so I end up with large files that nearly always need to be resampled to 44.1k, or saved permanently at 192k/24-bit. Typical filesize is 650Mb, largest so far is 5.66Gb - so that's an awful lot of time spent downsampling or pointless upsampling. I'm starting to think that the problems I'm experiencing may be due to sampling at "non-native" ASIO or WDM rates. I haven't tried sampling at 48/96k to see if that "fixes" the problem...
Using the WDM wrapper drivers (I don't know if these are provided - or supported! - by Creative or Adobe) results in randomly disabling one or the other Audigy. At that point, the only way to recover functionality for the disabled card is to reboot. Sometimes only the inputs are disabled, sometimes only the outputs, sometimes both. There is no pattern that I can see or duplicate.
Both cards appear to work fine under Windows. I can define either card as the default recording or playback device, and I can define one card as the default recording and the other as the default playback, any combination works fine. However, any application that uses WDM drivers to access the cards also get confused when a card's inputs suddenly become disabled! This does not appear to happen when Windows is the only application using the cards.
Specifying "use preferred devices" in Windows does disable the non-selected card (or card input or output if I specify different cards for input and output) in other applications.
The problems are much worse when I try to use any ASIO drivers to access the cards. This problem with ASIO appears regardless of the application I use.
I have installed ASIO4ALL, and it finds and configures the cards without any problems in ALL applications - but if I'm recording (with no other applications or drivers or tray applications loaded or active), when I stop recording and restart, the input I was just recording from appears disabled! If I open the ASIO4ALL configuration window, one or both Audigy cards will have their inputs disabled, or both inputs AND outputs disabled. This doesn't happen all the time, and my workaround is not to stop recording once I've started. Not a good workaround! I do realise that ASIO4ALL does fiddle around with the sample rates in the background, but at least when it works, I get a single clean sample without having to do all the resource-intensive resampling later. Maybe it's 6 of one, 1/2 dozen of the other...
I understand and appreciate that perhaps CL never intended to provide software functionality for more than one Audigy on any given PCI bus/bridge. I just don't get why the drivers appear to work natively under Windows (I'm assuming that Windows just uses WDM access) but not with any other applications.
I will try and do some testing with "native" ASIO sample rates (i.e. 48/96k) and see if that fixes some or all of the problems. My concern here is really that my expectation is that the drivers, once identified and enabled, should not suddenly disable themselves in all applications (by whatever mechanism), regardless of what sample rates are specified. But maybe that's too much to expect.
BTW, this happens with any combination of 2 of my 3 Audigy 2ZS cards, each of which works perfectly on its own with ASIO and WDM drivers. So it's definitely a multiple card issue.
The workaround that has been suggested is to purchase a different vendor's card : but there are so few cards that I can use to sample at the resolutions I require, and they are all so bloody expensive, that's why I've committed so much to CL Audigy 2ZS.
I'll get back to you once I've tried a few days working at the "standard" ASIO sample rates. Thanks again for taking the time with this stupid and unusual problem!
Kind regards,
Peter -
I can not do the update , what should I do to fix this error ?
"There was a problem with downloading the file . For tips on troubleshooting , please go to Customer Support . ( Error code : 204 ) ." thanksHi,
Please refer to the help document below:
Error downloading, installing, or updating Creative Cloud applications
Regards,
Sheena -
Good evening I would please help me, IGood evening I would please help me, I have problems with flash player when update on my computer Flash Player for windows 8, gives me error in the installation that is not apply on my computer. Please help. Thank You
First, confirm that ActiveX Filtering is configured to allow Flash content:
https://forums.adobe.com/thread/867968
Internet Explorer 11 introduces a number of changes both to how the browser identifies itself to remote web servers, and to how it processes JavaScript intended to target behaviors specific to Internet Explorer. Unfortunately, this means that content on some sites will be broken until the content provider changes their site to conform to the new development approach required by modern versions of IE.
You can try to work around these issues by using Compatibility View:
http://windows.microsoft.com/en-us/internet-explorer/use-compatibility-view#ie=ie-11
If that is too inconvenient, using Google Chrome may be a preferable alternative. -
Hello, I have a problem with iPhone 5c softhware update ( The iPhone "iPhone" could not be restored. An unknown error occurred (27))
Error 1 or -1
This may indicate a hardware issue with your device. Follow Troubleshooting security software issues, and restore your device on a different known-good computer. If the errors persist on another computer, the device may need service.
The" may need service' meand there is a hardware problem. In that case make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar -
I have a problem with my itube. I had itube and its gone. Now i cant get it back. How can i get it back without pay for it again?
We are Apple users here, and we answer technical questions.
Sorry, we cannot help you. -
I updated my ipad2 to ios7 after that , iam facing problems with my sim, it showing no sim card after inserting sim. there is no prbolem with my sim.
arun kumar chenna123 wrote:
i have updated my iphone to ios4.1. after installation, it is showing as"The SIM card inserted in this iPhone does not appear to be supported. only compatible sim cards from a supported carrier may be used to activate iphone. Please insert the sim card that came with your iphone...."
how to solve this problem. I don't have any sim cards that came with iphone.
Please help out to solve this problem.
It sounds like the phone was hacked or jailbroken, and updating it locked it to the original carrier. As it is not possible to update to any version other than the current one (5.1) the fact that you updated to 4.1 pretty much confirms the phone was hacked. There is no solution that you can get in an Apple forum. -
Hi! I 've a problem with my ipad mini. Does anyone know if there is a way to get out from recovery mode without reinstall iOS?
Many thanks Deggie! I think my iPad has a big problem because is not possible to restore it....I downloaded the most upgraded version of iOS but when I try to restore an error message occurs (4005)......
-
I have a problem with app store , they say my credict card security code is incorrect but it's correct
Did you check to see if your credit card has expired or has been frozen? My dad bought some hardware from Canada and it froze his card because it was an out of the country purchase. He called the bank and they turned it back on.
-
why can't i downgrade to mavericks? i have got some problem with yosmite. i would like to downgrade to mavericks.please help me how to get it ? thanks
Hi here are a couple of links you may find useful, the first is if you have made a time machine backup, the second if you have not.
http://osxdaily.com/2014/10/22/downgrade-os-x-yosemite-to-mavericks/
http://www.macworld.co.uk/how-to/mac-software/revert-back-mavericks-from-yosemit e-3581872/ -
İ have a problem with my itunes accounts.when i want to buy in-app features i got an error
İ have a problem with my itunes accounts.when i want to buy in-app features i got an error that;
"Please comtact with itunnes support for completing this process"
İ checked my device settings and tried my account with another ios device but result not changed.i still get same error.my credit card address info and my account address info same with each other.i tried my other credit cards but i got same error.
Please check my account details for solving this issue.
My account details :
email: [email protected]These are user-to-user forums, you are not talking to Apple here.
You can contact iTunes support via this page : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, the try selecting Purchases, Billing & Redemption -
I have problem with my Iphone 5, when I talk my ear allways tuch the screen and get it on no sound, the screen are not lock, is ti possible to lock the screen when incomming an outgoing call going on
Hello Mogulman46,
So what that means is when you have Do Not Disturb turned on, you may have an alert depending on the setting and how you are using your iPhone. So if it is set to Always, then that means that no matter what, your iPhone will not be notified. If it set to Only while the iPhone is locked, then that means that you will not get notification when your iPhone is locked but you will get notifications if your iPhone is being used. Also keep in mind the settings All Calls From can be set to certain contacts like Favorites, Everyone or no one. If you are using Do Not Disturb and you do not need it, then turn it off.
Use Do Not Disturb on your iPhone, iPad, or iPod touch
http://support.apple.com/kb/ht5463
Regards,
-Norm G. -
I have a problem with The verificación of The credit card in AppStore
I have a problem with The verificación of The credit card in AppStore ¿how could i solve it? U
U already fill al The spaces with The credit card, and ir says that The security code is invalid, ( and it is correct )Try:
- Reset the iOS device. Nothing will be lost
Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
least ten seconds, until the Apple logo appears.
- Reset all settings
Go to Settings > General > Reset and tap Reset All Settings.
All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
- Restore from backup. See:
iOS: Back up and restore your iOS device with iCloud or iTunes
- Restore to factory settings/new iOS device.
If still problem, make an appointment at the Genius Bar of an Apple store since it appears you have a hardware problem.
Apple Retail Store - Genius Bar -
help solve the problem, with the lifting of purchasing and payment card is locked, and now I can not pay for her purchases in the app store
Contact the App store for Apple ID help. Their support link is on the right of the App store window
LN
Maybe you are looking for
-
Is there a way to send mass Outlook calendar invites?
Our business is a subscription based business that has multiple service lines that hold a client only webinar each month. One of our service lines has found great success in terms of response and attendance sending out calendar invitations via Outloo
-
Inventory Report Not able 2 trace
Dear All, We are using "Z Report for Inventory Calcualtion of Opening and Closing Balance" The Opening Balanace and Closing Balance Figures are seen wiered in ur Production Server. But if run this same report in our QA Server.it works fine We are com
-
Batch insert from object variable
Any way to do this excluding the foreach loop container? I have millions of rows and if it goes through them 1 by 1 it will take hours maybe days. How can you do a batch insert from an object variable without putting the sql task inside a foreach l
-
Conditional Coloring for Server 2005 Reports
Hey Guys, I'm trying to use the Layout version in my Microsoft Visual Studio for Reports - and have no idea how to get my rows to follow a singular color format depending on a columns' input. For example, I would like the entire row to be yellow if t
-
Hi all, Following is mt requirement, On the first screen user should enter Purchase order no As he submits it there should be purchase order details should be displayed. in another window This requirementi want it to be presented in Simple report, A