Problem with Field image recovery software

Dears,
I updated cisco wlc 5508 FUS image, but field recovery image stayed the same, does this mean that fus is not upgraded, what can i do?
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 8.0.110.0
Bootloader Version............................... 1.0.20
Field Recovery Image Version..................... 6.0.182.0
Firmware Version................................. FPGA 1.7, Env 1.8, USB console 2.2
Build Type....................................... DATA + WPS + LDPE
System Name...................................... NW2-WLC01
System Location.................................. Level 11 Server Room
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1069
Redundancy Mode.................................. SSO
IP Address....................................... 10.10.12.8
IPv6 Address..................................... ::
Last Reset....................................... Software reset
System Up Time................................... 0 days 21 hrs 29 mins 51 secs
System Timezone Location......................... (GMT +4:00) Muscat, Abu Dhabi
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180

This is what you should see:
Cisco 5500 Series Wireless LAN Controllers
•Field Recovery Image is upgraded from 7.0.112.21 to 7.6.101.1
•Bootloader is upgraded to 1.0.20
•Offline Field Diagnostics is upgraded from 0.9.28 to 0.9.35
•FPGA Revision version is upgraded to 1.7
•Environment Controller (MCU) Image version is upgraded to 1.8
•USB Console Revision version is upgraded to 2.2
The issue is if you were upgrading the FUS to 1.9.0.0, you should of had console access to see what was going on. Typically the primary will download the image and write to flash and then the secondary would upload the image from the primary and write to flash. The secondary would need to be rebooted first then the primary. If the sysinfo didn't match between the two, then you need to upload the FUS 1.9.0.0 and do it again. This is if your have AP SSO enabled. If it's an N+1 configuration, then you need to upload the FUS 1.9.0.0 to the WLC that hasn't had everything upgraded and perform the upgrade again. From the console you can choose what you want upgraded by skipping the upgraded that is up to date.
-Scott

Similar Messages

Image recovery software

I am trying to find some image recovery software, I have looked at disk doctor, but it looks a bit shdey.
so basically i could do with a ligit version of something that works.
many thanks

This is what you should see:
Cisco 5500 Series Wireless LAN Controllers
•Field Recovery Image is upgraded from 7.0.112.21 to 7.6.101.1
•Bootloader is upgraded to 1.0.20
•Offline Field Diagnostics is upgraded from 0.9.28 to 0.9.35
•FPGA Revision version is upgraded to 1.7
•Environment Controller (MCU) Image version is upgraded to 1.8
•USB Console Revision version is upgraded to 2.2
The issue is if you were upgrading the FUS to 1.9.0.0, you should of had console access to see what was going on. Typically the primary will download the image and write to flash and then the secondary would upload the image from the primary and write to flash. The secondary would need to be rebooted first then the primary. If the sysinfo didn't match between the two, then you need to upload the FUS 1.9.0.0 and do it again. This is if your have AP SSO enabled. If it's an N+1 configuration, then you need to upload the FUS 1.9.0.0 to the WLC that hasn't had everything upgraded and perform the upgrade again. From the console you can choose what you want upgraded by skipping the upgraded that is up to date.
-Scott

Problems with importing images into Lightroom cc

Problems with importing images into Lightroom cc
I have installed lightroom cc and having trouble imortera images from my Canon 1DX.
Lightroom starting the capture, but then nothing happens more, if I turn off the camera, I get error message photo 100-200 could not be loaded.
Now I have left lightroom 5 and where the input port works fine.
What happened to the upgrade from Lightroom 5 to lightroom cc?
The camera has the latest software.

I've now tested in various ways.
First, I have images on both memory cards in the camera.
Test1) Selects Not all of the photos in the camera at the input port bearings, it seems to work fine.
Test 2) selects all cards in the camera and then get the following, Lightroom starts inportera short but stops and nothing happens (Fig.1).
I turn the camera off after a while and get the next meddelnade (picture 1)
Which can be translated:
"The following files were not imported because they could not read (351)
Property 1-100
etc. "
Picture 1.
Picture 2

Problem with Rescue and Recovery after installing Norton Internet Security 2010

Hi all.
It's my first time in this forum.
I have a problem, with Rescue and Recovery, after installing Norton Internet Security 2010 on my T43.
The message I get it:
"Rescue and Recovery is unable to back up the file 'C:\Documents and settings\all Users\Application Data\ Norton\ 00000082\00000109\000003c1\cltMLS1.bat' Because the file is either corrupted or being used by another application. Please close any application that could be using the file.
I tried to close the Norton but I couldn't find how.
Tanks
Doron71

Hi and welcome to the forum,
the reason for this situation is, that the antivir files are protected from being modified.
This is the reason, why this file cannot be backed up. I assume, that you would get much more such messages, as there are surelly multiple files files, that are protected like this.
So the solution is to block folders from being archived. Please start RnR application and in the configuration set this folder as the excluded one.
This will skip the backup of this file and will fix your situation.
Please let me know, if you have covered this.
Cheers

Problem with Gif image

Having a problem with gif image not showing up. It will show up in netscape6.2, but not in IE 5.0. Both are using the java 1.4 plugin. They are basic buttons (zoom in, zoom out, etc) and they actions work, just the icons aren't showing. Any help would be great! Below is a snip of code:
JPanel toolBarsPanel = new JPanel();
javax.swing.JToolBar toolbar = new javax.swing.JToolBar();
JButton zoomin = new JButton(new ImageIcon("tut/zoomin.gif"));
JButton fullext = new JButton(new ImageIcon("tut/fullextent.gif"));
JButton identify = new JButton(new ImageIcon("tut/identify.gif"));
JButton btn = new JButton(new ImageIcon("tut/addtheme.gif"));
toolbar.add(zoomin);
toolbar.add(fullext);
toolbar.add(identify);
toolbar.add(btn);
add(toolbar, BorderLayout.NORTH);
Thanks again for any help!

I used to do a lot of work in this sort of thing. After a while we were able to convince our bosses to use generated HTML (JSPs, etc.), so the problem moved to porting JavaScript to different platforms! (Platforms in this context means the different browser/OS combinations, etc.).
The only two things I can recommend are:
- complete control over you code. You will have to fix it! (Tried you apps on a Mac yet?)
- assume a minimal install. Don't assume users are going to have any fancy tools installed on their PC, unless you are developing an Intranet app, where you know the spec of the machines that are going to be using it.
As regarding getting IE to use a relative address, I don't think you are going to have any luck their, I'm afraid! (Although I am curious. It has been some time, but I though it did use relative addresses. Are you absolutely sure about this, did you check this out with System.outs and that?
HTH,
Manuel Amago.

For the last 2 days whenever I try to upload photos from my iPhoto page to facebook I get an error message: Bad Image There was a problem with the image file. I haven't knowingly changed any settings on iPhoto or facebook. Can anyone help, please ?

I need help with uploading photos from iPhoto to facebook. I could do it till 2 days ago. Now any new photo I try to upload gives me an error message:
Bad Image
There was a problem with the image file.
Please help.

Can you drag it to the Desktop?

I gotta problem with security question recovery email I'd, mistakenly I entered wrong email I'd so now I want to edit that I'd plz help me

I gotta problem with security question recovery email I'd, mistakenly I entered wrong email I'd so now I want to edit that I'd plz help me

expresslane.apple.com to get a hold of itunes to reset them by email the only way

I have a problem with vertical images burned on a cd

I have a problem with vertical images burned on a cd either from a Mac or a stand alone burner. What happens is the images come from the card and are put on the cd. Also note the the camera has been set for the computer to automatically show images vertically when shot that way. The images look good on my Mac, but are horizontal on windows computers. Both XP and Vista. What can be done?
John

Hi, thank you for the response... not sure looks that the battery its ok, I'm not sure.
Charge Information:
Charge remaining (mAh):    4356
Fully charged:    Yes
Charging:    No
Full charge capacity (mAh):    4356
Health Information:
Cycle count:    813
Condition:    Normal
Battery Installed:    Yes
Amperage (mA):    0
Voltage (mV):    12571

I have problems with uploading images to my printing company have the images have been manipulated through CS6 i have saved images as jpeg but the printer company tell me they are not j peg, they will not upload images save from a camera are fine

I have problems with uploading images to my internet printing company when the images have been manipulated through CS6 and i have saved images as jpeg the printer company tell me they are not j peg,
but images saved from my phone or camera images that have not been manipulated upload fine, What am i doing wrong?

Save/Export them as JPG. Photoshop defaults to PSD, so make sure you select JPG and not just rename the file to .jpg.
There are two ways to save them as JPG: Regular Save as option or Save for Web & Devices
Take your pick.

Very urgent : Problem with field attributes in Datasource

Hi
I am getting a problem with field attributes in the datasource.
The issue came up after i modified the extract structure-i modified one field and
added one field to the structure.Now those two fields are not visible in BW.
When i checked with transaction rsa2, i could find that for those two fields , the
field attribute is <b>'A'</b> which is <b>'Field in OLTP and BW Hidden by SAP'</b>.
I tried to modify the field attribute to make it visible.Now the issue is that it is not getting reflected after transport in the Q system.What can be the issue.In the Q system its still the old value 'A' ,which makes the fields invisible.
Please let me know what can be the issue.
Regards
Leon

Hi,
did you change this attribute via RSA2?
you need to change your datasource via postprocessing (RSA6); then transport your DS to your Q source system.
Replicate your datasources in your BW.
Finally modifiy your Transfer Structure by editing your TRules ( tab Datasource/Tran structure), move your new fields from the right frame to the left frame)
Maintain your TRules
Activate
hope this helps...
Olivier.

Problem with field GL Account is that it shows concatenated Chart of Accoun

Hello . Please help me. We have sap BI olap universe . problem with field GL Account is that it shows concatenated Chart of Accounts. But user want to trim the chart of account and show only account in list of values in webi report.
So What code I can put in Universe to remove this " 9000/" WHICH IS Chart of acct from GL Account
example List of values shows
9000/99030
9000/99070
I want to show as below
99030
99070
I tried replace function in universe it does not work. Pls help.
Thanks
soniya

Hi,
You can do it in Web Intelligence using the function Right().
Depending on the SAP BW version you have it is possible to build such calculated expression in universe on uniquename or name:
<EXPRESSION>RIGHT[0CALMONTH].currentmember.uniquename,5)</EXPRESSION>
OR
<EXPRESSION>RIGHT([0CALMONTH].currentmember.name,5)</EXPRESSION>
You have to replace 0CALMONTH by the unique definition of GL Accounts and you also need to use the object referencing GL Accounts in your query in addtion to the calculated expression.
Regatds
Didier

Problem with field label

Hello All,
I am having a strange problem with field label? I have created a table with three fields one is MANDT and and the remaining fields as PATID and PATNA.
I am maintaining the field label for these fields, but still i am not getting the names of the fields while i am calling the structure in my alv tree.
I d'nt know what is the problem here?
can any one tell me how can i solve this issue?
Regards,
Lisa

Hi lisa,
This is not the problem with Data Dictionary,
While declaring the fieldcatalogue for thr GRID.
CALL FUNCTION 'LVC_FIELDCATALOG_MERGE'
EXPORTING
I_BUFFER_ACTIVE              =
   I_STRUCTURE_NAME             = 'ZTABLE'
I_CLIENT_NEVER_DISPLAY       = 'X'
I_BYPASSING_BUFFER           =
CHANGING
    ct_fieldcat                  = gt_fieldcat
EXCEPTIONS
INCONSISTENT_INTERFACE       = 1
PROGRAM_ERROR                = 2
OTHERS                       = 3
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
If gt_fieldcat-fieldname = 'PATID'.
gs_fieldcat-ref_field = 'ZTABLE'.
modify gt_fieldcat from gs_fieldcat.
clear gs_fieldcat.
endif.
Because while calling the FM it is populatinh the fieldname
so you need to modify the fieldcatalogue with fieldname then it will pick the field labels from the Dictionary.
Hope this will solve your problem.
Regards,

Problem with field KONWA-Rate Unit(Currency or Percentage) of table KONP

Hi Gurus,
I m facing problem with field 'KONWA -Rate Unit (Currency or Percentage)' of table KONP. This field is showing Currency and '%' both in table KONP. For some materials its showing currency value and for some its showing '%'. Due to which its creating load problems. My question is how this '%' is coming (means is there any calculation behind that or something else) in table KONP and how can I identify this.
I am sure u will have the answer for this question so Thanks in advance.
Message was edited by:
        Amit Rajput
Message was edited by:
        Amit Rajput
null

Hi,
take the following example: you sell liquor to customers; in your country, when you sell liquor your company is entitled to pay customs and excise fees to governamental authorities.
These excises and duties are a percentage of the retail price. You'll then create such a condition record with this rate so that you calculation schema will post the correct value during the processing of billing documents...
hope this shed light
Olivier.
Message was edited by:
        Olivier Cora

Problem with displaying image

Hello!
Sorry, I'm a beginner in APEX and have some problems with displaying images in my application. I have read the same topic but unfortunately didnt find the solution.
So.. I have the interactive report
table test (
NAME NOT NULL VARCHAR2(4000)
ID NUMBER
BLOB_CONTENT BLOB
MIME_TYPE VARCHAR2(4000))
I need to display the column blob_content.
Thnks a lot.

1009316 wrote:
Hello! Welcome to the forum: please read the FAQ and forum sticky threads (if you haven't done so already), and update your forum profile with a real handle instead of "1009316".
When you have a problem you'll get a faster, more effective response by including as much relevant information as possible upfront. This should include:
<li>Full APEX version
<li>Full DB/version/edition/host OS
<li>Web server architecture (EPG, OHS or APEX listener/host OS)
<li>Browser(s) and version(s) used
<li>Theme
<li>Template(s)
<li>Region/item type(s) (making particular distinction as to whether a "report" is a standard report, an interactive report, or in fact an "updateable report" (i.e. a tabular form)
With APEX we're also fortunate to have a great resource in apex.oracle.com where we can reproduce and share problems. Reproducing things there is the best way to troubleshoot most issues, especially those relating to layout and visual formatting. If you expect a detailed answer then it's appropriate for you to take on a significant part of the effort by getting as far as possible with an example of the problem on apex.oracle.com before asking for assistance with specific issues, which we can then see at first hand.
Sorry, I'm a beginner in APEX and have some problems with displaying images in my application. I have read the same topic but unfortunately didnt find the solution.
So.. I have the interactive report
table test (
NAME NOT NULL VARCHAR2(4000)
ID NUMBER
BLOB_CONTENT BLOB
MIME_TYPE VARCHAR2(4000))
I need to display the column blob_content.This is described in the documentation: About BLOB Support in Forms and Reports and Display Image. There's an OBE tutorial that followed the introduction of declarative BLOB support in 3.1 as well.

Problem with RMAN incomplete recovery

Oracle Version: 9i
Operating System: Windows 2000
I have a problem with RMAN incomplete recovery until sequence.
According to my database structure ............
SQL> SELECT GROUP#,SEQUENCE#,THREAD# FROM V$LOG;
GROUP# SEQUENCE# THREAD#
1 14 1
2 13 1
3 12 1
I took the backup of backup of full database using RMAN and i am trying to recover like this:
RUN
ALLOCATE CHANNEL C1 TYPE DISK;
SET UNTIL SEQUENCE 7 THREAD 1;
RESTORE DATABASE;
RECOVER DATABASE;
ALTER DATABASE OPEN RESETLOGS;
BUT i am getting a message saying there is no backup of DATAFILE 1,2,......10 to restore although my database is in archivelog mode and i took a backup.
Yachendra

Please consult v$backup_datafile.
It will tell you when the file was backed up.
RMAN will always search for a datafile backup prior to the logsequence or whatever is limiting the incomplete recovery.
Likely when you made your backup Oracle was already past sequence 7.
Sybrand Bakker
Senior Oracle DBA

Problem with Field image recovery software

Similar Messages

Maybe you are looking for