Problem with new P35 Neo2 Build

Ok, I had a Gigabyte DS3 rev. 1.0 before and I narrowed it down to the MB failing, which I've heard alot of before. So I bought a MSI P35 Neo2 (rev 1.1, Bios 1.1) to replace it and just put it back together with the following parts:
C2D E6400, Mushkin 2GB XP PC2-6400, 2 Samsung 250GB Sata HDDs. On first boot up it went fine and I was in the BIOS and set it up, then booted into Windows Vista. Just today I tried to start the PC but nothing, so I cleared the cmos and it then started up, but hung. The leds in the group 1, 2, 3 & 4 are all red. In the manual it states "System Power On, The D-LED will hang here if the processor is damaged or not installed properly".
Am I to assume my cpu is toast now?

So I swapped my Q6600 into my P35 Neo2 and it still has the 4 red leds! I also swapped out the video card for my HD 2600XT, and the power supply with my Seasonic SS-500HT 500W PS, and ram (OCZ PC6400 2GB) and still 4 red leds. I also tried the C2D E6400 in my Abit Quad GT and it boots up fine. I've pretty much narrowed it down to the motherboard I guess. What are my options at this point?
Thanks
***Update***
Well, I just figured it out. When I swapped power supplies I forgot to plug the 8 pin connector into the MB. There is nothing wrong with my CPU or my MB.
The stats on my other P/S (SS-500HT are, +3.3v - 30A, +5.0v - 30A, +12V1 - 17A, +12V2 - 16A., not alot more than my other P/S, but just enough to get it to work??
Anyway, I am going to get a new P/S. I am looking at either the Corsair VX550, I can get it for $84 Cdn, plus a $15 MIR, which you probably never get anyway. How about PC Power & Cooling Silencer 610W EPS12V? It's more money, but I hear good things about their P/S's??
Is it better to go with a large single 12V rail as apposed to multiple lower rails?
Thanks for your help.

Similar Messages

  • A problem with the P35 Neo2-FR

    Greetings
    Firstly I'm new to this forum and by the looks of it its not based in Europe so you're all probably asleep right now.
    Anyway, I am having trouble getting this motherboard, Neo2-FR, to boot at all and nothing but a blank screen. No BIOS, no splashscreen, nothing.
    When I short the power switch it turns on, then off, then on and the LEDs go through the sequences of red/green until it reaches green, green, red, green and stops. The red CMOS LED is lit constantly, the blue PCI-E LED is lit, LED 13 (PCI slot 1) flickers constantly but the PCI slots are empty.
    I've tried using 4 sticks of RAM, 2sticks of RAM and 1stick of RAM. It makes no difference. The FSB has been set to 200, 266 and 333 to no effect. I have tried plugging in a floppy drive, CD-ROM and harddrive all to no effect. I have tried pressing the CMOS switch, shorting the power, shorting the reset switch and patience.
    I'm very thorough and usually something is faulty when I can't fix it.
    Whats wrong with it? Is LED flickering a bad sign?
    edit: this board should boot without a BIOS update for 45nm chips
    Thank you for all your support
    -MSI P35 Neo2-FR (UK) revision A7345 IMS 150 and BIOS unknown
    -Intel socket 775 E8400 "Wolfdale" stepping C0 Retail
    -DDR2 Crucial Ballistix PC5300 CAS 3 1Gb x4
    -Ati HD3850xt 512MB DDR3
    -Enermax Noisetaker 600w 3.3V 34A 5V 34A 12V1 18A 12V2 18A
    -Hard Drives: Not available
    -Optical Drives: LG 4123B DVD-RW
    -Operating System - not installed
    Here is a picture:
    http://homepages.nildram.co.uk/~zen12084/Storage/helpme.jpg

    That's definetely a new one...
    I would still flash to the correct BIOS with the CPU microcode for your Wolfdale. That BIOS would be v1.6: >>Link<<
    Flash the BIOS with our USB flashing tool: >>MSI Forum HQ USB Flashing Tool<<

  • Problems with msi p35 neo 2

    Default problems with msi p35 neo 2
        pc works fine when using windows and the net and emails
        only when using 3d mark or games do i ever get problems
        just help in getting the hole story 6 months ago got a msi neo2 install all my old components core 2 duo 4 gig ram form a diffrent board works fine but never used it playing games just used for the net and email shoping seamed to work fine but
        tryed playing a game 2 months later command and conquer 3 pc was some times freeze or graphics artefacts on screen assumed vga card faulty got another graphics card geforce 8600gts installed still the same in the last month got round to playing with the pc again and installed new g7 780 watt power supply and ati hd 4870 graphics card
        now i can use 3d mark some times it will go through once or just freeze or 3d mark stops the test
        temps on the board (from msi dual core center temps cpu 33oc system 47oc)
        memory voltage 2.1
        any one know the settings for the ram
    more details you need
    System Details
    MotherboardEdit Value
        msi p35 neo2 fr
    Motherboard BIOSEdit Value
        latest
    CPUEdit Value
        core 2 quad 6600
    CPU Overclock SpeedEdit Value
        none
    CPU HeatsinkEdit Value
        standard intel that come with cpu
    CPU Idle TempEdit Value
        N/A
    CPU Load TempEdit Value
        N/A
    MemoryEdit Value
        ******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
    Memory VoltageEdit Value
        N/A
    Video Card(s)Edit Value
        ati hd4870
    Video Card SpeedEdit Value
        N/A
    Sound CardEdit Value
        onboard
    PSUEdit Value
        g7 780 watt power extreme
    Hard Drive(s)Edit Value
        mator dimondmax 21
    Optical Drive(s)Edit Value
        N/A
    Other CoolingEdit Value
        3 80mm fans 1 frount 1 back 1 side
    ModsEdit Value
        N/A
    Operating SystemEdit Value
        windows 7

    Quote
        ******* xms2 2x2 gb ddr2 part no cm2x2048 6400c4dmx
       Quote
    memory voltage 2.1
    Make sure that the memory timings are not set to 4-4-4-x but that they are set to the defaults values (5-5-5-x).  Also ensure, that the memory clock speed is not set to anything higher than 400 MHz (=DDR2-800).  The voltage at these settings should not need to exceed 1.95V.  So please lower it accordingly.  In case the freezes still occure, please run memtest86+ to check your memory for errors.
    Quote
    msi dual core center
    Please get rid of that tool for all further tests.  Uninstall it completely from your system as it is known to cause crashes and freezes on its own terms when running.

  • Problem with new version 4.3.2 apps not working " after update to the new version "

    Problem with new version 4.3.2 apps not working " after update to the new version "
    i was in 4.3.1 then i do the update , but now after update i face this problem , so what i Supposed to do ?!!

    Hi There
    Had the same problem as you. App would terminate when launched.
    Solution to working You Tube app:
    -Go to playstore
    - Uninstall app (it doesn't remove the app, only removes the update)
    - "Et Voila", working again.
    This doesn't correct the problem, it's just a workaround for you to be able to use youtube app again.
    Hope it helped.
    Best Regards

  • I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add

    I bought new i phone 5 3 days back, after that asked for new update which is 6.1.4, after updating my iphone i am not able to use cellular data services. I called up data provider, they says its the problem with new software update. There is no option add APN. Now when i switch to safari its showing you are not subscribed for cellular data. But I am able to use data on other phone.
    Will you please help me in this regard?
    Another issue, since i bought my new iphone there is dust inside back main camera.
    Your advises are highly appreciated.

    Hey Shaiju isac,
    I'd take a look at the following article, it'll guide you though steps to you troubleshoot cellular data issues on your iPhone:
    iPhone: Troubleshooting a cellular data connection
    http://support.apple.com/kb/ts3780
    Cheers,
    David

  • Wifi problems with new ipad

    I'm trying to learn how to correct wifi problems with new iPad.  It is the wifi only, 64GB model.  I want to be able to use it at work, where we have a great wifi network.  I can usually connect to our network with no problem, but after an hour or so my iPad loses the network.  When I try to reconnect, I see that the network is showing full strength reception, but I get the error message from the iPad that I am "Unable to join" the network.  My iPhone connects to the same network seamlessly, as do all of the other iPhones of my co-workers and the older generation iPads that some of our staff has.
    At other locations, I typically have no problems (home, apple store, etc.) but I have had the same situation pop up at a coffee shop where I could see that there was a wifi network available, but I could not join it even though it was the shop's free wifi. 
    I have tried turning the iPad off, turning off wifi and turning it back on again, and forgetting the wifi network in question.  I can't think of any other methods that are available to an end user to correct the problem. 
    I have already gone to the Apple store to swap out the unit, and the newer one is having the same symptoms. 
    Can anyone offer any advice here?  This is quite frustrating.

    No problem! Have a read at this most interesting article which has special significance as regards your models!
    http://edition.cnn.com/2012/04/05/tech/gaming-gadgets/ipad-wi-fi-issues/index.ht ml
    However, I attach an extract from another thread for your perusal. You can disregard any suggestions/links you have already explored -
    created by Texas Mac Man in Using iPad - View the full discussion
    Look at iOS Troubleshooting Wi-Fi networks and connections  http://support.apple.com/kb/TS1398
    Additional things to try.
    Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router &amp; then back On. Now boot your iPad. Hopefully it will see the WiFi.
    Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
    How to Quickly Fix iPad 3 Wi-Fi Reception Problems
    http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
    If none of the above suggestions work, look at this link.
    iPad Wi-Fi Problems: Comprehensive List of Fixes
    http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
     Cheers, Tom ;)

  • List of Problems with new Web Mail

    List of Problems with NEW Web Mail :
    - At first doesn't open full page message list or retain full page as default setting, have to drag down bar
    - Only shows 20 message lines after “pulling down” the divider, screen partially empty until I scroll down.  It should show at least 26, preferably all available
    - After moving bar, bar moves back up after going back to inbox (not delete message) after reading a message, have to move it down again, and again...
    - Doesn't go to next message when delete message on screen is selected, no setting option for default to do this.
    - There is a drop down to select which folder to move a selected email to.  The initial display shows 7 usable choices, with the usual slider and arrow to show more choices.  The space on the slider clearly shows more choices are present (actually about 20 or so are there), but any attempt to use the slider or arrow to see more choices causes the drop-down to instantly disappear.  I can't move the selected field with arrow keys either.  I can select any of the visible 7 choices, and move an email to only one of the 7.  NOTE: This one works in both IE and Firefox, but if Verizon Webmail was fully web standard (see http://en.wikipedia.org/wiki/Web_standards) compliant it would also work in my preferred browser, Mozilla Seamonkey, the direct descendant of the original Mozilla browser.  Webmail should be FULLY web standard.
    - Occasionally a message will move from inbox to trash, without NO indication or command to move them.
    - Emails occasionally flash an error message and simply disappear - not to trash or other findable place, just disappear.  No time to read the error message either.
    - No way to set a whitelist for supposed spam emails, unless the whitelist for “Blocking” is the same.  Very unclear.
    - How can I switch my service back to the original, basic, email which works ok?  I know it’s still there, since some of my other accounts still access it!!!
    This seems my only way of getting this info direclty to the programming staff.  If it doesn't actually do this, will SOMEONE PLEASE FORWARD THIS MESSAGE TO THEM !?!  
    Thanks!

    vz_ric wrote:
    The majority of websites are set up the same way for all browsers. It's the software manufacturers responsibility to make their software compatible with websites, not the other way around. Otherwise everyone who has a website will have to make 10 different sites to work multiple browsers.
    Contrarily, it is Verizon's, as well as other companies like Verizon whose customer base uses a wide variety of web browsers, web page designers' responsibility to use only standard W3C-recognized code and not to use non-standard non-W3C-recognized code, e.g., Microsoft's Internet Explorer specific code, when designing their web pages. In my opinion based on my observations, Verizon's web page designers are too often guilty of using IE-specific code.

  • Adobe aftereffects is not working on os x maverics all updates...... is dis soft. will work on the new os x yosemite.??  y apple is nt working on dis problem wen users are facing problems with new os x .....

    Adobe aftereffects is not working on os x maverics all updates...... is dis soft. will work on the new os x yosemite.??  y apple is nt working on dis problem wen users are facing problems with new os x .....

    I suggest you contact Adobe tech support or their Mac forums for assistance.

  • Reposting this If your having problems with new Windows 8.1 do a full uninstall of all Apple

    Reposting this If your having problems with new Windows 8.1 do a full uninstall of all Apple iTunes programs but uninstall them in right order and then do restart of computer then reinstall newest iTunes and it will all be fixed up syncing problems or other problems this is thanks to Apple phone support

    What is your technical support question for these user to user technical support forums?

  • When Apple solve problems with new iTunes calendar sync with windows and outlook?

    When Apple solve problems with new iTunes calendar sync with windows and outlook?

    Anything Downloaded with a Particular Apple ID is tied to that Apple ID and Cannot be Merged or Transferred to a Different Apple ID
    More Info here...
    Apple ID FAQs  >  http://support.apple.com/kb/HT5622
    If necessary...
    Contact iTunes Customer Service and request assistance
    Use this Link  >  Apple  Support  iTunes Store  Contact

  • Before I buy has there been any problems with new 27 iMacs?

    Before I spend my hard earned cash does anyone know if there has been any problems with new 27 iMacs?

    Hello richard from Folsom:
    Are you inside or outside?  (  I could not resist, I lived in Sactown).
    Anyway, advice is frequently worth what you pay for it, and mine is free.
    If you want it, buy it.  The posts above are right on the mark (except waiting is probably overly-cautious).  The best advice (from anamusic) is to buy the extended warranty - well worth the money.
    Barry 

  • I just started using my iphone 5s. I have a problem with new incoming emails from my POP account. Why are they marked as read automatically even though I have not even opened them yet.

    I just started using my iphone 5s. I have a problem with new incoming emails from my POP account. Why are they marked as read automatically even though I have not even opened them yet.
    At first I thought it might be because I was using simultaneously my old iPhone 4S so it somehow realized the emails where being pushed to another device and the it marked as read, this has nothing to do since I have deleted the email account from the iPhone 4S

    Contact the email provider for assistance with their service.

  • Provisioning Profile - problems with installation our app build on devices

    We have problems with installation our app build on few devices. There are all in Provisioning Profile, but we don't know why we can't install the build on some devices. Any ideas?

    Apple products needing Apple love/support (athough using Adobe to compile to Apple-code may be an obvious concern since nothing beats native-code)
    The app still however requires code-signing in the correct manner - personally, the more the merrier.

  • Premiere Elements 13 , Problems with new text/titles

    Premiere Elements 13, bisher keine Probleme. Nachdem die Filmlänge etwa 15 Minuten beträgt immer größere Probleme Titel/texte einzugeben. Wartezeiten sind extrem lange oder Programm stürzt ganz ab.

    High ATR,
    Computer running on Widows 7 ,64 Bit System, Service Pack 1, Processor AMD Phenom(tm) X4 945 3.00 Ghz;RAM 8 GB
    Grafikkarte: NVIDIA GeForce 8800 GT
    If the video on the timeline is longer than 10 minutes the problem will be remarkable. The response times adding a title is getting longer(2-15 seconds).
    As the video is now 18 minutes the response time is after each action(resizing of letters or any changes of the text) up to 30 seconds or the program crashes completely.
    Project settings are the following:
    General HD 1080i; 29,97frames/second; Video:1920v 1080 H, 30 fps
    Video: maximale Bittiefe, Dateiformat i-frame only mpeg, Kompressor MPRG i-Frame, Standbilder optimieren
    The video is a mixture  of full HD videos 1920x 1080 .mov and pictures up to 4608x3456 pixels.
    When the program crashes I remarked that the main memory RAM(8Gb) was fully used by the premiere program. Might there be a problem?
    Thank you for your service.
    thomasd
    Von: A.T. Romano 
    Gesendet: Sonntag, 1. Februar 2015 23:55
    An: Thomas Deschler
    Betreff:  Premiere Elements 13 , Problems with new text/titles
    Premiere Elements 13 , Problems with new text/titles
    created by A.T. Romano <https://forums.adobe.com/people/A.T.+Romano>  in Premiere Elements - View the full discussion <https://forums.adobe.com/message/7151822#7151822>

  • Facebook problems with new macbook pro.

    Facebook problems with new macbook pro. I can't publish photo albums to timeline. I can't share items onto timeline. Photos I'm tagged in don't appear on my timeline. Any help?

    Yes! Been living in a hellish nightmare since Sept-Oct. Unlike you, however, Apple has been of no help. They say the iPad is unhackable, plist and crash reports are none of my business and who understands them anyway, their route tracing apps are probably not reliable. The best they could do was wipe the iPad clean. Lost photos they said would be in the cloud....
    Almost immediately was back in somebody's VPN, their remote controller, video, audio, working. Got the purple buddy for the first time today. I have been invaded, my iPad no longer feels like my own, I have lost thanksgiving, Christmas, new year trying to track down the invaders, signed up for a Cisco course, set/reset passwords.
    I don't know who else to contact... Or what next to do.
    I've read similar frustration in other posts, scattered around the support communities. Yours is the only one that has worked toward a solution.
    How did you get anyone at apple to look at your logs and acknowledge there is a problem?
    Would be happy for a suggestion on how to proceed. Already been the apple store genius and tech on phone route.

Maybe you are looking for