Process open FD table is full

Hello !
sun directory server 5.2 patch 6
linux redhat 3.7
My directory server was out yesterday.
Here is the error message :
[10/Dec/2008:17:35:24 +0100] - ERROR<12289> - Connection - conn=-1 op=-1 msgId=-1 - PR_Accept() failed, error -5971 (Process open FD table is full.)
[10/Dec/2008:17:35:24 +0100] - ERROR<12289> - Connection - conn=-1 op=-1 msgId=-1 - PR_Accept() failed, error -5971 (Process open FD table is full.)
[10/Dec/2008:17:35:24 +0100] - ERROR<12289> - Connection - conn=-1 op=-1 msgId=-1 - PR_Accept() failed, error -5971 (Process open FD table is full.)
Parameter from the dse.ldif :
nsslapd-maxdescriptors: 1024
System parameter :
ulimit -a | grep open
open files (-n) 65536
Common error rfering to sun's documentation :
12289: PR_Accept() failed error variable (variable)
Cause:
The problem depends on the variable and is based on the Netscape Portable Runtime (NSPR) error layer.
Solution:
If you determine that the cause of the problem is that the TCP port to which you are attempting to bind is already in use, consider the following actions.
* Restart the server, using a different port.
* Stop the application bound to that port and restart the server.
But it doesn't explain my problem because the port (389) is not in use. The problem is due to the number of open file...
What is the best practice on this parameter ? (sun directory + operating system)
The process slapd runs using another user as root
Thanks

Well, you should monitor your number of concurrent connections to the directory and where they come from in order to determine if they're legitimate or not.
Then, among the legitimate connections, may be some of them are idle, something that you can also easily see through the console or the cn=monitor tree.
If so, consider using idle timeouts at the user or directory level.
Finally, if you really need to have a large number of simultaneous open connections, increase nsslapd-maxdescriptor to something your hardware can afford,
up to the configured system limit (a bit less actually).
Also notice you can sometimes lower the number of fd's used by the directory by adjusting (to a lower value than the default of 2 hours) the TCP time wait timeout.
It could help in the situation where you see lots of connections in this state .
Hope this helps .

Similar Messages

PR_Accept() failed, error -5971 (Process open FD table is full.)

I am working on a web app which uses the SunONE directory server for
some authorization. Sometimes it happens that the webserver just hangs
with no errors in the webserver log. In the slapd error logs I do see
the following exceptions :
PR_Accept() failed, error -5971 (Process open FD table is full.)
I am not sure why is this happening? What could be the problem? I am
assuming FD means the file descriptor? One bug we found in the app is
that it tries to add a new user in the LDAP even if its there. I do get
"add value to attribute type nsRoleDN in entry .....: duplicate value"
exceptions, but thought its harmless. Could this exception be causing
something?

Hi,
I had exactly the same error message. I did not find the cause of this after spending a lot of time looking around. I only know it is a file descriptor table problem. The sun one directory server access log, however, did not have the number of file descriptors count reached maximum. I am very much puzzled by this. Did you find out why yet?
u4me2

Problem with DS5.1 patch1( PR_Accept() failed, error -5971 (Process open FD

Hi all,
I install iplanet Directory Server5.1p1 on Solaris 8. These errors fill full in my error log files
"PR_Accept() failed, error -5971 (Process open FD table is full.)"
I use idsktune tool and detect i face the problem file descripton. I have increase to 4096 ( in /etc/system file and ulimit -n 4096), but these errors still exist in my error logs.
Who know this prolem, pls give us a solution to fix this errors
Thank alot
Best Regards

I suggest you try the Directory Server forum.

Pls Help. DS5.1p1 errors PR_Accept() failed, error -5971 (Process open FD t

Hi all,
I install iplanet Directory Server5.1p1 on Solaris 8. These errors fill full in my error log files
"PR_Accept() failed, error -5971 (Process open FD table is full.)"
I use idsktune tool and detect i face the problem file descripton. I have increase to 4096 ( in /etc/system file and ulimit -n 4096), but these errors still exist in my error logs.
Who know this prolem, pls give us a solution to fix this errors
Thank alot
Best Regards

Hi!
To increase the FDs available for DS, edit the Configuration --> Performance Settings and increase the no. of FDs available for DS. please check if you havent done this.
I faced the similar problem. Increased the system limit(/etc/system) and DS setting, but was still recieving the error message time to time, which disappears automatically, when FDs get freed. The server is quite a busy LDAP server.
Can someone comment how can i see the actual Fd utilisation on a Solaris 8 system.
I have been checking like:
ls -l /procs/fd | wc -l
and by:
ls -l /procs/pid-of-slapd/fd | wc -l
But always find the Fds in use to be quite lesser than the limit specified 4096.
Thanks for sharing.
Cheers!
VIvek

Delete the initialization of delta on open hub table

HI Gurus
I have loaded data from cube to open hub table using DTP with full update, later on i have loaded the data using a DTP with delta update. Now i am thinking that delta has been initialized on the open hub table, so now want to delete the initialization of delta on the open hub table. It would be great if some one could send me the response.
Thanks
Rohit

Hi Sam,
If I understand you correctly,
You have removed your Initialisation by going InfoPackage --> Scheduler --> Initialization Options for Source --> Removed the Request
Then you did Init without Data Transfer
Then you have the option from init withoout Data transfer to Delta in InfoPackage and Loaded the Data.
Check in the Process Chain the InfoPackage you have mentioned in the selections may pointing towards Init load instead of Delta.
Sudhakar.

Mavericks getting error "file: table is full"

Hi,
since upgrading to Mavericks I noticed very odd behaviour on my MBP 2012 after some days of uptime. Tabs in browsers stopped working, internet connections got cut off and apps crashed and weren't able to restart. Only a reboot helped. This started to happen regularly, after 1 - 2 days of uptime.
I've since asked around and used the "dmesg"-command in the terminal to see the kernel log when this behavious occurs. It's always the same, lines and lines of "file: table is full".
I've switched off my CrashPlan backup service which I deemed the culprit. It didn't help. I've checked my SSD for errors, SMART-Status says "GOOD" and disk repair doesn't find anything wrong with the disk.
I've also noticed that this error coincided with "QTKITServer"-processes showing up as not responding and shockwave-plugin crashing, at least when using Chrome. I now switched from Chrome to Safari to see if maybe Chrome causes this odd behaviour but I'm not very optimistic about it.
Has anyone any ideas how to narrow this problem further down or maybe even what to do about it? Any help is greatly appreciated.
Thanks.

See below the report for an explanation
The startup items & kernel extensions are a concern, are they up to date or not used? Update or remove via uninstallers or removal instructions. You have privoxy & glimmer blocker running, isn't that two web proxies?
The 2 failed launchd jobs are system level, so update or remove the related software or delete the .plists
          [failed] com.vmware.launchd.vmware.plist
          [failed] com.bitcasa.BitcasaUI.plist
Adobe updater appears to have 2 user jobs failing too… within your user account.
          [failed] com.adobe.ARM.[...].plist
          [failed] com.adobe.ARM.[...].plist
You can isolate issues with user level tasks by trying to login in a new user account. If that helps it's time to update or remove all the login items & background launchd jobs.
Google apps have caused some users issues, ensure they are up to date or remove them to see if they are the cause. Delete the system level .plists to prevent the updaters from running - the app will nag you about recreating them anyway.
You also have quite lot of internet plugins, I'd consider deleting them all & reinstalling as needed, it's easier than hunting down updated versions.
jfkorn wrote:
Startup Items:
          ArcanaStartupSound - Path: /Library/StartupItems/ArcanaStartupSound
          ParallelsTransporter - Path: /Library/StartupItems/ParallelsTransporter
          Privoxy - Path: /Library/StartupItems/Privoxy
          Wireshark - Path: /Library/StartupItems/Wireshark
Kernel Extensions:
          org.dungeon.driver.SATSMARTDriver          (0.6)
          com.AmbrosiaSW.AudioSupport          (4.1.2)
          virtualcdrw.driver          (1.0)
Launch Daemons:
          [loaded] com.adobe.fpsaud.plist
          [loaded] com.adobe.SwitchBoard.plist
          [loaded] com.ambrosiasw.ambrosiaaudiosupporthelper.daemon.plist
          [loaded] com.crashplan.engine.plist
          [loaded] com.google.keystone.daemon.plist
          [loaded] com.microsoft.office.licensing.helper.plist
          [loaded] com.skype.skypeinstaller.plist
          [failed] com.vmware.launchd.vmware.plist
          [loaded] org.cindori.AuthHelper.plist
          [loaded] org.glimmerblocker.proxy.plist
          [loaded] phonostarTimer.plist
Launch Agents:
          [not loaded] com.adobe.AAM.Updater-1.0.plist
          [loaded] com.adobe.AdobeCreativeCloud.plist
          [loaded] com.adobe.CS5ServiceManager.plist
          [failed] com.bitcasa.BitcasaUI.plist
          [loaded] com.google.keystone.agent.plist
          [loaded] org.glimmerblocker.updater.plist
          [loaded] virtualcdrw.daemon.plist
User Launch Agents:
          [loaded] com.adobe.AAM.Updater-1.0.plist
          [failed] com.adobe.ARM.[...].plist
          [failed] com.adobe.ARM.[...].plist
          [loaded] com.crashplan.javacheck.plist
          [loaded] com.spotify.webhelper.plist
          [loaded] com.valvesoftware.steamclean.plist
          [loaded] de.metaquark.appfresh.plist
          [not loaded] info.lokiware.attachmenttamer.cleanup.plist
          [loaded] info.lokiware.attachmenttamer.setupagent.plist
          [loaded] uk.co.markallan.clamxav.freshclam.plist
          [loaded] ws.agile.1PasswordAgent.plist
User Login Items:
          Flux
          CheatSheet
          BetterTouchTool
          Alfred
          ClamXavSentry
          Dropbox
          Tunnelblick
          DaemonManager
3rd Party Preference Panes:
          AppTrap
          BTTPrefs
          Connect360
          DivX
          Flash Player
          Flip4Mac WMV
          GlimmerBlocker
          Growl
          Java
Internet Plug-ins:
          AdobeAAMDetect.plugin
          AdobePDFViewer.plugin
          CoolirisWebKitPlugin.plugin
          Default Browser.plugin
          DFusionWebPlugin.plugin
          DFusionWebPluginS64.plugin
          DivXBrowserPlugin.plugin
          Flash Player.plugin
          FlashPlayer-10.6.plugin
          Flip4Mac WMV Plugin.plugin
          googletalkbrowserplugin.plugin
          iPhotoPhotocast.plugin
          JavaAppletPlugin.plugin
          JoostPlugin.plugin
          npgtpo3dautoplugin.plugin
          o1dbrowserplugin.plugin
          OfficeLiveBrowserPlugin.plugin
          QuakeLivePlugin.plugin
          QuickTime Plugin.plugin
          RealPlayer Plugin.plugin
          SharePointBrowserPlugin.plugin
          Silverlight.plugin
          Veoh Plugin.plugin
User Internet Plug-ins:
          Google Earth Web Plug-in.plugin
          Move-Media-Player.plugin
          PDF Browser Plugin.plugin
          PDEPrint.plugin
          Picasa.plugin
          Unity Player.plugin
Red items are loaded at the system level (not necessarily bad, but they have the potential to modify the OS).
Blue items are loaded at the user level
Your RAM & HD look OK in terms of space etc, no obvious bad signs, the swap used (page-outs) should decrease when less of the old apps are running.
Cleanup:
All the usual caveats apply, backup before you modify the system, delete the items (or move them to another disk or folder if you are worried about deleting the wrong thing) but ensure the originals are gone or updated.
Use the Finders "Go menu > Go to Folder…" when you need to open the hidden ~/Library (your users library).
Reboot for the system changes to take effect.
How to find updates:
The critical launchd jobs & kernel extensions use reverse domain notation e.g.
com.logmein.hamachi.plist means look at http://logmein.com for updates (if you don't recognize it removing it may be appropriate)
In short: You want to try to update or remove all the system level items.
Startup Items: Stored in /Library/StartupItems/
Startup Items have been discontinued by Apple since Mac OS 10.4. They are responsible for making changes at a system level. Remove them all or spend time ensuring ALL related software is up to date. You need a very good reason to have anything installed in here. The developers are ignoring Apple guidelines by installing these - not a good sign.
Kernel Extensions: Stored in /Library/Extensions/
Kernel Extensions also load third party code, but they insert it into the 'core' of the OS. These can be safe, however you must ensure the related tools or apps are up to date, otherwise the system is basically built upon quicksand. Remove them all & see if the OS works better.
Launchd jobs: several types
LaunchAgents          - Stored in /Library/LaunchAgents
LaunchDaemons       - Stored in /Library/LaunchDaemons
User LaunchAgents   - Stored in ~/Library/LaunchAgents
These are all background jobs, they are not necessarily bad, but if they are loading old code it could be doing untold damage to the performance & stability of the entire OS. Focus on the System level jobs (the ones inside /Library - the system level) also remove ['failed'], non-system jobs.
EtreCheck gives a status on launchd jobs…
[loaded]                  - a running job
[not loaded]            - jobs that are set not to run, basically harmless, remove them unless you plan to use the associated software (if it is up to date)
[failed]                    - jobs in a crashed or unknown state, it could be forking processes or using all the system resources, remove these.
User login items:
Applications and helpers that are managed inside 'Systems Preferences > Users and groups > Login Items tab'.
These are loaded at the 'User level', consider removing all of them whilst you troubleshoot. When you decide to re-add them ensure the software is up to date.
3rd Party Preference Panes: & Internet Plug-ins:
/Library/PreferencePanes/ and ~/Library/PreferencePanes/
/Library/Internet Plug-Ins/ and ~/Library/Internet Plug-Ins/
Once again these items all must be up to date, or remove them from your system. If the prefpanes manage additional software use the uninstaller or see the developers site for uninstall instructions. You can also right click to remove 3rd party preference panes in System preferences
Read the list of Internet plug-ins carefully, there are often duplicate Flash player versions that won't help stability, it's just wasted space too.
Don't forget to also update Safari's extensions in it's preferences (if you have any).
Re-run EtreCheck after cleaning up to see if items have returned (some apps will reload the background jobs when re-opened, so either update or remove the software).
Hope that isn't too daunting, the OS should be better if there are less old items running at the system level.

File table is full

I just had an unpleasant crash on my 10.8.3 system, with the logs telling me "file table is full" (many, many times). Verify and Repair volume didn't find any errors, and a df now shows that I've still got loads of available inodes,
$ df -ih /
Filesystem Size Used Avail Capacity iused ifree %iused Mounted on
/dev/disk4 1.8Ti 1.0Ti 820Gi 56% 273127665 214959156 56% /
And other than Spotlight telling me that it will take 4 hours to re-index everything, I see no problems now. Should I suspect that some process started creating files with abandon? My Dropbox client (version 2.0.8) had been acting strangely during the day. (Claiming that it always had one file to sync, but never syncing it). Skype (6.3.0.582) was the first to report to me an I/O error. I'm also not sure how I can fill up the file table without first running out of inodes, but I don't know the internals of HFS+ and my days of understanding ufs are long behind me.
So the question(s): Should I suspect that some process started creating files with abandon or should I consider some other cause and how do I investigate further?
Cheers,
-j

If you have more than one user account, these instructions must be carried out as an administrator.
Triple-click anywhere in the line below to select it:
syslog -k Sender kernel -k Message CSeq "I/O error" | tail
Copy the selected text to the Clipboard (command-C).
Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Terminal in the icon grid.
Paste into the Terminal window (command-V).
The command may take a noticeable amount of time to run. Wait for a new line ending in a dollar sign (“$”) to appear.
Post any lines of output that appear below what you entered — the text, please, not a screenshot.

Proc: table is full - garbled version

I've been getting this message once in a while on my Server, it becomes very sluggish and I need to reboot it to get it back to work (I usually am able to log in after a few tries):
kernel[0]: proc: table is full
Last night however, I got messages like this:
kernel[0]: proc: proc: table itabls fulle is
kernel[0]: proc: tablproc: table is full
kernel[0]: proc: table pris foc: table is full
What is going on here?
A reboot fixed the problem, like in the previous cases, but what could have caused these weird entries in the log?

It started after I updated Parallels to MC1 and installed Security Update 2006-003.
I did install QT 7.1.1 to see if it'd fix the problem, but nope it did not.
I suspect Parallels to be the problem. I cannot pinpoint exactly when that started to happen but for sure it was after both events.
I've since uninstalled Parallels but the problem persists.
When OS X runs out of space in the proc table nothing can start, so unless terminal is already up and running there's no way to kill those processes. And I believe they will rise from the dead...
I was able to identify what causes those smbd to start. It starts when I open my PC laptop which is on the same network and try to view a shared folder from my iMac. Samba (smbd) is supposed to get started at that point to serve my shared directory. For some still unknown reason instead of spawning one process it keeps spawning smbd's till OS X's proc table fills up.
Only alternative is to restart and nothing else can get started.
One thing I tried was to remove smbd from /usr/sbin, actually rename it so it never gets started. That prevents me from seeing the iMac from any Win machine on the network. So far that's my temporary solution, but I'm still looking for clues...
Please let me know if you are using Parallels as well, or not and I can eliminate it from the guilty list
cheers,
julio

Line items seen in fbln but not in process open items

Hi Gurus,
one line item is seen in fbl3n but not in process open items in f-07,
the entry is rent a/c Dr
to rent payable a/c
we can see is fb03, fbl3n of both accounts
Pl suggest. I am unable to clear

Dear Shymalasandia,
You can reach REGUP by se11 and insert the document number that You can see by FBL1N but not during the payment.
Probably it is contained into a payment proposal (F110) and therefore You cannot pay it manually (to avoid double payment).
If You find it into REGUP table, You have two options:
1.pay it by F110
2. delete the payment proposal by F110 (menu> edit> proposal--> delete) and pay it manually.
I hope this helps.
Mauri

APEX and 11.5.10 Payables Open Interface Tables

Hi,
Wanted to see if APEX would be a tool that could be used to connect to oracle application interface tables and load data from a spread sheet into the ap_invoices_interface and ap_invoice_lines_interface tables. Once this is done the information could be interfaced into the application.
Has anyone done this?
Thanks in advance for any responses.

Scott,
Do you have experience in how to populate Oracle eBusiness Suite Open Interface tables with Excel-data using a APEX form/report/process?
If so, can you give me a clue how to do it? Uploading CSV will not work, because of treating text-fields as numbers. Our item numbers look like numbers, but must be handled as text. Example: 002.112.002
Regards,
Geert.

RECEIVING OPEN INTERFACE TABLE의 STRUCK RECORDS 정보 취합 SCRIPT

제품 : MFG_PO
작성날짜 : 2005-01-27
RECEIVING OPEN INTERFACE TABLE의 STRUCK RECORDS 정보 취합 SCRIPT
=================================================================
PURPOSE
RCV_TRANSACTIONS_INTERFACE table에 있는 struck receipt records의 정보를
취합하여, struck 원인 및 해결에 도움을 줄 수 있다.
(Oracle Purchasing - Version: 11.5.2 to 11.5.9)
Explanation
Receiving Open Interface Tables에 걸려 있는 receipt struck의 source
document의 추가 정보를 어떻게 취합할 수 있을것인가?
(RCV_TRANSACTIONS_INTERFACE)
Source document는 아래 중 하나가 될 수 있다.
* Purchase Order
* Return Material Authorization (RMA)
* Internal Requisition
아래에 소개하는 scripts는 interface tables에 많은 수의 records가 있을때,
많은 수의 records의 정보를 한 번에 취합하길 원할때 사용하면 유용하다.
만약 interface tables에 단지 몇 개의 records만 있다면 Note: 171257.1
- Oracle Procurement (Purchasing)/iProcurement Diagnostic Tests 에 소개
되어져 있는 적당한 diagnostic script를 이용하는편이 낫다.
Example
1.Error가 발생한 Purchase Order receipts의 추가 정보를 취합하는 script:
SELECT SUBSTR(POH.SEGMENT1,1,10) "PO Number",
POR.RELEASE_NUM "Release Num",
POL.LINE_NUM "Line Num",
RTI.INTERFACE_TRANSACTION_ID "Intf Trx Id",
RTI.TRANSACTION_DATE "Trx Date",
RTI.PROCESSING_MODE_CODE "Proc Mode",
RTI.TRANSACTION_STATUS_CODE "Trx Status",
RTI.PROCESSING_STATUS_CODE "Proc Status",
SUBSTR(PIE.ERROR_MESSAGE,1,75) "Error Message",
POH.ORG_ID "Op Unit Id",
RTI.PO_HEADER_ID "PO Hdr Id",
RTI.PO_RELEASE_ID "Rel Id",
RTI.PO_LINE_ID "PO Line Id",
RTI.PO_LINE_LOCATION_ID "Line Loc Id",
RTI.QUANTITY "Intf Qty",
POLL.QUANTITY "Order Qty",
POLL.QUANTITY_RECEIVED "Qty recvd",
POD.QUANTITY_DELIVERED "Qty Delv",
NVL(POLL.CLOSED_CODE,'OPEN') "Closed Code",
OOD.ORGANIZATION_CODE "To Inv Org",
RTI.DESTINATION_TYPE_CODE "Dest Type",
RTI.TRANSACTION_TYPE "Intf Trx Type",
NVL(POLL.QTY_RCV_EXCEPTION_CODE,'NONE') "Qty Exception",
POLL.QTY_RCV_TOLERANCE "Qty Tolerance",
POLL.RECEIVE_CLOSE_TOLERANCE "Receipt Tolerance"
FROM RCV_TRANSACTIONS_INTERFACE RTI,
PO_HEADERS_ALL POH,
PO_RELEASES_ALL POR,
PO_LINES_ALL POL,
PO_LINE_LOCATIONS_ALL POLL,
ORG_ORGANIZATION_DEFINITIONS OOD,
PO_DISTRIBUTIONS_ALL POD,
PO_INTERFACE_ERRORS PIE
WHERE POH.PO_HEADER_ID = RTI.PO_HEADER_ID
AND POR.PO_RELEASE_ID(+) = RTI.PO_RELEASE_ID
AND POL.PO_LINE_ID = RTI.PO_LINE_ID
AND OOD.ORGANIZATION_ID(+) = RTI.TO_ORGANIZATION_ID
AND POLL.LINE_LOCATION_ID = RTI.PO_LINE_LOCATION_ID
AND POD.LINE_LOCATION_ID = POLL.LINE_LOCATION_ID
AND RTI.INTERFACE_TRANSACTION_ID = PIE.INTERFACE_TRANSACTION_ID(+);
2.Error가 발생한 RMA receipts의 추가 정보를 취합하는 script:
SELECT RTI.INTERFACE_TRANSACTION_ID "Interface Transaction ID",
RTI.PROCESSING_STATUS_CODE "Processing Status",
RTI.PROCESSING_MODE_CODE "Processing Mode",
RTI.TRANSACTION_STATUS_CODE "Transaction Status",
RTI.TRANSACTION_TYPE "Transaction Type",
RTI.TRANSACTION_DATE "Transaction Date",
RTI.OE_ORDER_HEADER_ID "Order header Id",
OOH.ORDER_NUMBER "Order Number",
OOH.ORG_ID "Oper Unit Id",
RTI.OE_ORDER_LINE_ID "Order Line Id",
OOL.INVENTORY_ITEM_ID "Order Item",
OOL.FLOW_STATUS_CODE "Line Flow Status Code",
RTI.QUANTITY "Intf Qty",
RTI.UNIT_OF_MEASURE "Intf UOM",
OOL.ORDERED_QUANTITY "Qty Ordered",
OOL.SHIPPED_QUANTITY "Qty Shipped",
OOL.FULFILLED_QUANTITY "Qty Fulfilled",
OOL.OPEN_FLAG "Open Flag",
OOL.CANCELLED_FLAG "Cancelled",
WH.ORGANIZATION_CODE||' - '||WH.ORGANIZATION_NAME
"Ship To Organization",
WH1.ORGANIZATION_CODE||' - '||WH1.ORGANIZATION_NAME
"Ship From Organization",
OOL.BOOKED_FLAG "Booked",
SUBSTR(PIE.ERROR_MESSAGE,1,75) "Error Message"
FROM RCV_TRANSACTIONS_INTERFACE RTI,
OE_ORDER_LINES_ALL OOL,
OE_ORDER_HEADERS_ALL OOH,
ORG_ORGANIZATION_DEFINITIONS WH,
ORG_ORGANIZATION_DEFINITIONS WH1,
PO_INTERFACE_ERRORS PIE
WHERE OOL.HEADER_ID = RTI.OE_ORDER_HEADER_ID
AND OOL.LINE_CATEGORY_CODE = 'RETURN'
AND OOL.LINE_ID = RTI.OE_ORDER_LINE_ID
AND OOH.HEADER_ID = RTI.OE_ORDER_HEADER_ID
AND OOL.SHIP_TO_ORG_ID = WH.ORGANIZATION_ID(+)
AND OOL.SHIP_FROM_ORG_ID = WH1.ORGANIZATION_ID(+)
AND RTI.INTERFACE_TRANSACTION_ID = PIE.INTERFACE_TRANSACTION_ID(+)
ORDER BY RTI.INTERFACE_TRANSACTION_ID;
3.Error가 발생한 Internal Requisition receipts의 추가 정보를 취합하는
script:
SELECT RTI.RECEIPT_SOURCE_CODE "Receipt Source Code",
RTI.REQUISITION_LINE_ID "Intf Req Line Id",
RTI.SHIPMENT_HEADER_ID "Ship Hdr Id",
RTI.SHIPMENT_LINE_ID "Ship Line Id",
RTI.ITEM_ID "Item Id",
RTI.QUANTITY "Intf Qty",
RTI.UNIT_OF_MEASURE "UOM",
RTI.FROM_ORGANIZATION_ID "From Org Id",
RTI.TO_ORGANIZATION_ID "To Org id",
PRH.REQUISITION_HEADER_ID "Req Hdr Id",
PRH.SEGMENT1 "Req Num",
PRL.REQUISITION_LINE_ID "Req Line Id",
NVL(PRL.QUANTITY_DELIVERED,0) "Qty Delv",
NVL(PRL.QUANTITY_CANCELLED,0) "Qty Canc",
PRL.QUANTITY "Qty Ordered",
PRL.QUANTITY - (nvl(PRL.QUANTITY_CANCELLED,0) +
NVL(PRL.QUANTITY_DELIVERED,0))"Qty Remaining",
PRL.SOURCE_TYPE_CODE "Source Type",
PRH.TRANSFERRED_TO_OE_FLAG "XFR to OE Flag",
NVL(PRL.CANCEL_FLAG,'N') "Cancelled",
NVL(PRL.CLOSED_CODE,'OPEN') "Closed Code",
LIN.LINE_ID "ISO Line Id",
NVL(LIN.ORDERED_QUANTITY,0) "ISO Line Qty",
NVL(LIN.SHIPPED_QUANTITY,0) "ISO Ship Qty",
NVL(FULFILLED_QUANTITY,0) "ISO Fulfilled Qty",
NVL(LIN.CANCELLED_QUANTITY,0) "ISO Cancelled Qty",
NVL(LIN.OPEN_FLAG,'N') "ISO Line Open",
NVL(LIN.BOOKED_FLAG,'N') "ISO Line Booked",
NVL(LIN.CANCELLED_FLAG,'N') "ISO Line Cancelled",
OOH.ORDER_NUMBER "ISO Order Number",
PIE.COLUMN_NAME "Intf Column",
SUBSTR(PIE.ERROR_MESSAGE,1,75) "Error Message"
FROM RCV_TRANSACTIONS_INTERFACE RTI,
PO_REQUISITION_HEADERS_ALL PRH,
PO_REQUISITION_LINES_ALL PRL,
PO_INTERFACE_ERRORS PIE,
OE_ORDER_LINES_ALL LIN,
OE_ORDER_HEADERS_ALL OOH
WHERE PRL.REQUISITION_HEADER_ID = PRH.REQUISITION_HEADER_ID
AND RTI.REQUISITION_LINE_ID = PRL.REQUISITION_LINE_ID
AND LIN.SOURCE_DOCUMENT_ID = PRH.REQUISITION_HEADER_ID
AND LIN.SOURCE_DOCUMENT_LINE_ID = PRL.REQUISITION_LINE_ID
AND LIN.SOURCE_DOCUMENT_TYPE_ID = 10 --Internal Requisition
AND OOH.HEADER_ID = LIN.HEADER_ID
AND PIE.INTERFACE_TRANSACTION_ID(+) = RTI.INTERFACE_TRANSACTION_ID
ORDER by PRH.SEGMENT1;
Reference Documents
Note 263368.1

Any suggestion/advise please!
Thanks,
Genoo

Not able to process open items using F-53

Hello All,
I am trying to process open items using F-53, I m getting error message as "Entry SAG1 is missing in table T043G". This was working fine for GL accounts, but failing for vendors.
I checked the tolerance group for same and its fine and also tried checking table se16, but not able to find the root cause of issue. please let me know how can i resolve this.
Thanks in advance.
--Sagar

HI,
Check following...
1. Make sure you have created one null (Blank) tolrance group using transaction OBA3 for your company code SAG1...
2. If you do not want to create null tolerance group then make sure you have mapped the tolerance group created to the customer master and also see the use assignment...
Regards,
Chintan Joshi

Sap r/3 rel 4.6c - F-03 Process open Items; standard output; column width

Hello All:
I use SAP R/3 Release 4.6C. I am learning how to use the F-03 Clear G/L Account function. On the front page of F-03 you enter the account number and then click process open items.
The output comes on the screen in the "standard" tab. In this tab you may start to clear your items.
My question: How do you change the width of these columns? I know you can change the column width by moving the column margin with the mouse. I want to know how to change the column width permanently - make the column a "fixed" width that will not change unless I change it.
thx
Tracy Lofstedt
Western States Equipment Co

First adjust all the columns as you prefer, then click on the table settings,configuration icon on the right top. Give a name in the variant and click save. Tick the check-box Use as standard setting.

Do F-32 Clear Customer and Process Open Items just do BKPF/BSEG adds/chgs ?

!uestion 1:
When a user executes F-32 in "clear customer" and "process open items" modalities, are BKPF and BSEG the only tables that actually get changed via adds or updates?
Or are there other tables affected as well?
Question 2:
If BKPF and BSEG are the only affected tables, can I safely emulate the effect of the F-32 Clear Customer and Process Open Items Modalities by:
1) examining the BKPF/BSEG records added or changed;
2) using the appropriate BAPI(s) to accomplish these adds/changes (like BAPI_ACC_DOCUMENT_POST)
Question 3:
If BKPF and BSEG are NOT the only tables affected by F-32 Clear Customer and Process Open Items, can I emulate these modalities of F-32 thru an appropriate combinaton of BAPIs ?
Note:
The reason Im asking these questions the way I am is because a search of SDN turns up no really good answer to the question of whether the Clear Customer and Process Open Items modlaities of F-32 can be emulated by one BAPI or a combination of BAPI's.
So by formulating questions (1-3) the way I have, I'm hoping that someone will provide SDN with a clear and definitive answer to the "F-32 BAPI Emulation" question.
Thanks for any expert advice anyone can provide.
Best
djh

Actually, the "right" answer in this case is to call CLEAR_DOCUMENTS and model the call after the call in PRELIMINARY_POSTING_ZANF_CLEAR

Yesterday i bought ipad4 i transfered photos from pc to ipad that it opened in ipad when i click slideshow everything went black. whenever i m opening the application(photos) full screen looking black but all photos are occuping memory.

yesterday i bought ipad4 i transfered photos from pc to ipad that it opened in ipad when i click slideshow everything went black. whenever i m opening the application(photos) full screen looking black but all photos are occuping memory.i can see the pictures in settings>brightness>wallpapers but i couldnt able to see in photos application in ipad4

I have several thousand photos in several folders. I have noticed that whenever I want to change the folder used as the side show source, it takes the Screen Saver Preference pane a very long time to respond. It is as if it is scanning all the photos in the currently assigned folder in order to display them in the preview window provided, and it gets so dogged down doing that it can't respond to my clicks on the Choose Folder option.
Assuming you don't want to redistribute your photos into a greater number of folders or subfolders so there would be fewer in each folder to process, you could try a workaround. Try moving your currently-assigned folder to your desktop temporarily, before opening the Screen Saver preference pane. If the preference pane can't find the old folder, it may immediately ask you to choose a new one. You could hopefully then do so, close the preference pane, and then put back the old folder.
It's my understanding that there will be no future updates to Tiger, only security fixes.

Process open FD table is full

Similar Messages

Maybe you are looking for