Questions for my first pc with the msi neo2 fr motherboard

my setup :
intel e6750
2048 corsair pc6400
zalman 9700 led
hdd 250 go seagate sata2
msi8800gt
i'm building my first pc with this mobo and i have some questions because i d'ont want to make mistakes
what is the difference between the purple and the blue sata connectors? witch is the correct one for my hdd? my os will be xp sp2 and i d'ont really understand if sata drivers will be needed for the installation of xp
concerning the memory : everything must be plugged on the green slot or one on the green and one on the orange slot?
thanks for you help

What drummer_tom is pointing to is the Dual Channel config for RAMs.
Slot 1 + 3 or Slot 2 + 4 or all 4 slots installed, will give you Dual Channel performance and capacity. A win-win situation.
As for the Blue and Purple Sata connectors, the 4 purple SATA connectors are controlled by Intel ICH9R chipset and the 1 blue SATA connector is controlled by Marvell controller. Only the Intel controlled SATA ports are able to RAID.

Similar Messages

CSS11500 SSL handling question for multiple url/FQDNs with the same ip address

I know that it's possible on the CSS to handle multiple incoming HTTP requests that terminate on the same IP address and port and balance them to various servers based on the url. For instance, I can set up www.cats.com and www.dogs.com at the same 192.168.35.12 address in DNS, and set up two different content rules:
content cats
vip address 192.168.35.12
port 80
url "//www.cats.com/*"
add server cats1
add server cats2
active
content dogs
vip 192.168.35.12
port 80
url "//www.dogs.com/*"
add server dogs1
add server dogs2
active.
Easy and straightforward.
But what if I want to add SSL handling for https://www.cats.com and https://www.dogs.com?
I'm not sure how to create the ssl-proxy-list where one content rule (ip address/port) combination needs to pass through the ssl module and get matched with the proper ssl certificate.
Can this be done? Can one associate multiple certs and keys with a single ssl-server entry and a single ssl accelerator service? Or do I have to create multiple ssl-proxy-lists for cats and dogs and build multiple ssl services each referring to a unique ssl-proxy-list, and then use the url parameter in the https content rule to determine which ssl service (and therefore which key/cert pair) gets the traffic?
Thanks in advance for any insights.

Hi Tim,
Unfortunately this is not possible; you can't associate multiple certificates to a single proxy list due to the fact that SSL handshake is done first with no visibility of the URL being requested, so the CSS won't know which public server to use in order to perform the traffic decryption.
But there are a couple of options that you may want to look at (depending on the URL string)
If your URLs are subdomains and you hold a wildcard SSL certficate to match multiple requests, i.e your domain being "pets.com" you can have a certficate that will match request for dogs.pets.com or cats.pets.com because the cert will be in the form *.pets.com
The second option is SAN (Subject alternative names) certificates; which give you the option to include up to 4 flavors of the domain within the same file, such as pets.com, pets.net, www.1pets.com.
I hope this helps.
Pablo

Getting rpm values from the fans on the MSI NEO2-FIR motherboard doesn't work

I currently have 6 Noctua NF-S12-1200 120mm fans spinning in my computer but i am unable to get rpm values from them except the cpu-fan. It doesn't work to get a readout from the others with either, BIOS, Dual Core Center or Speedfan. Regarding Speedfan is it true it don't support the SuperIO Chip on the Neo2, the FINTEK F71882F? It's not currently listed in their supported temperature sensors list.
So whats the problem? Shouldn't atleast DualCore Center atleast show the rpm's from the other chassis fans?
Or the fans don't support sensor readings?
Thanks!

Quote from: Jack on 13-October-10, 00:15:36
Well, there is nothing that can be done about. SysFAN 1 & 4 support sensor readings, #2,#3 and #5 don't. You can also see that in BIOS Setup. #1&#4 are the only ones that show up there (H/W Monitor section). This is not a malfunction or a bug. You have to live with no fan sensor readings or be creative about the wiring.
The problem is that i use the UNLA cables from Noctua which half the speed of the NF-S12 fans i run with. And it blocks the rpm readouts in Speedfan and BIOS.
http://www.noctua.at/main.php?show=productview&products_id=5&lng=en
Strange thing is that the CPU fan reads fine with the ULNA cable attached but the SYSFANS will not read the rpm with the ULNA cables.
What is wrong?

Multiple Issues with the MSI board...

This is my first experience with the MSI board and so far its not very smooth... I have this MSI NEO 2 standard board My specs are
P4 2.8C
256 MB (single module) DDR 400 RAM. (TWIN MOS)
Geforce Ti4200..
80 GB Maxtor SATA
FAX
CD-ROM
WIth WINDOWS XP HOME Edition..
i have done no overclocking and the problems are..
1. First of all it takes lot of time to show the first screen... like the vga card screen comes after 4 seconds.
2. Some time i press the power button and when the system is detecting the hard disk and CDROM it gives error message like DRAM timings are too tight. i have check the BIOS setting and everything is normal and there is no overclocking and RAM is rated to run at 400 MHz.. although not a great brand but not a bad one either..
3. Sometime just before loading the operating system it gives an error message that No boot sector found.. insert a Bootable floppy or CDROM.. and when i restart it start going on as usual..
So wot are the causes of these problem .. i think mainboard is the main culprit... i have scanned my system with 2 anti virus and there is no virus..
any suggestions..?
Thanks..

Quote
Originally posted by Eddio1
I've been reading the posts here for about a week and I decided to finally ask for some assistance. Just picked up the MSI 865PE Neo2-V from BZBOYZ.COM and 1Gb generic matched Elixir 512's and I've tried dozens of bios settings as posted here. I was finally able to install 2003 ent. server and if I'm lucky, it will get past the 2003 splash screen to a login screen, I'll log in, then put it to work (you know browse some heavily populated folders) it freezes and a reset is necessary. Now, I cant even get past the splash screen. I must have booted 200 times with every bios combination and I'm tired of doing fresh installs and experiencing the same system freeze issues. I've been in the IT business and built dozens of boxes in the past and never had such problems (using bios failsafe defaults no less!) getting an OS to install and run in a reasonably stable fashion. Mobos these days are extremely frustrating! I'm going to pick up some Corsair twinx RAM and hopefully this will resolve. Any ideas would be greatly appreciated in advance of more waiting and RMAing the RAM I have for some Corsair. Do you think I'm on the right track because I'm gonna be really pissed if new RAM doesn't do the trick.
Bios settings:
Bus mastering enabled
Configured RAM manually in bios 3-4-4-7-8 (tried PSD to no avail)
Disabled dynamic o/c
Disabled spread spectrum
Normal speed
HT enabled
All other settings bios setup defaults
MoBO specs:
MSI 865PE Neo2-V latest bios: Version 5.4 Update date 2004-7-5
http://www.msi.com.tw/program/products/mainboard/mbd/pro_mbd_detail.php?UID=612
P4 3.2 Prescott
400 FSB
1Gb Elixir PC3200 RAM (I suspect this cheap RAM is the issue)
Memtest says it runs at 3-3-3-8
I configured it manually in bios (per some previous posts) to run 3-4-4-7 (only way to get a boot)
Native for SATA/ATA
PS-Enermax EG365P-VE FCA-3.3V-32A, +5-32A, +12-26A
ATI Radeon 8500 64MB
Seagate SCSI Cheetah-36Gb 15K 160Mb/s
Seagate SCSI Barracuda-73Gb 10K 160Mb/s
Adaptec 29160N
Boot to Adaptec then floppy then CD
HI check my previous thread, entitled problem after udate of xp, or look for threads with name on Sounds like a similar problem.

What's with the MSI support?

I bought a MSI-K8N Platinum about 6 weeks ago and since that day I've had nothing but trouble with my wireless network. As I'm not one of those who gives up instantly I figured that I might solve the (what seems to be software)-problems on my own or at worst with the guidance of MSI:s cunning support. It seems that I was severly mistaken though.. I've posted in two threads in this very forum without any answer and I've mailed the MSI support concerning my issue without any luck. Now it seems that my hard work has payed off with a mainboard that it's too late to reship and with an useless wireless network that cost me another 200$ of my hard earned student-salary.
When can I hope to get an answer to my questions? Or any response at all for that sake?
Here's links to the threads concerning this issue:
https://forum-en.msi.com/index.php?topic=66928.0
https://forum-en.msi.com/index.php?topic=25278.0
Furthermore I'm still waiting for the support to contact me. I would very much like to get to use my high-end equipment before it's yesterdays news...
Sorry if this thread makes me come of as a b**ch, but it seems that I'm not getting attention with this matter of mine. I'm sure the support and this forum is an excellent node for other concerns.
// Klab0

In Reply to syar 2003:
I've already had my wireless network for a while and it (still) works perfectly with my old Abit m0b0. It consists of a D-link DWL-G520, D-link DWL-G650 and a D-link DI-624 accesspoint.
In Reply in general:
I've tried with belkin for my workstation but it seems to be in conflict with my other D-link products. Hence I don't want to mix network brands because as you say, they usually has quite poor compability, and for another thing I would like to be able to use the "boost"-functions available when using all D-link Etreme G products (Extended range and "108Mbs"). It seems quite odd to me that pretty much every D-link product except my DWL-G520 is supported by my mainboard, and since I know for a fact that there's nothing wrong with the card I'm led to beleive that the problem has something to do with my software configuration.
Problem specifics:
I've updated to the latest mainboard and ethernet drivers for my mainboard, I have NOT installed digicell though since I figured it would be messy with two separate programs trying to configure my wireless network. I've deactivated the firewire, GbLAN and ethernet in the BIOS without any result. I've tried with the PCI-card in PCI-slot 5 and 4 (the orange one optimized for wireless networks and the one next to it.) The system seems to find the card with the right drivers and it seems to work perfectly except for one thing: I can't achieve contact with the acesspoint.
In one of the threads i hijacked the person who made the thread said that he solved the problem, so I'm still hoping to work this thing out somehow. What I'm really wondering is if there's some basic mistake (a BIOS-setting etc) that often comes up as a problem for lamers like me when setting up a wireless network with this mainboard. I will try with the MSI wireless PCI-card that came with the mainboard if I can't solve it with my existing DWL-G520, but it is really a pain in the a** since I suppose it will only lead to compabilityproblems with the acesspoint instead.
If anyone has a slightest clue, please don't hesitate to mention it. It might as well be something very basic that has been overlooked. Thanks guys.

Help with the MSI 645 Ultra!

I've got a very frusturating problem. I just bought the MSI 645 ultra mobo to upgrade my system, along with a brand new P4 2.0 GHZ processor and 512 mb DDR ram to go onto the board. My problem is as follows: The computer is not booting up. No OS, no BIOS, no nothing. When I turn the power on and hit the switch, all the hardware in the case starts up and sounds fine... but the screen remains blank. All four lights on the little diagnostic tool/usb port thingy that came with the board stay red, which, according to the manual, indicates a problem with the processor.
The processor is either bad (highly unlikely with it being an Intel chip) or for some reason its not working with the mobo. So, heres my question: Does an Intel P4 2.0 GHZ Northwood processor work with the MSI 645 Ultra?
Under the list of supported speeds, 2.0 ghz is not listed ?( . Can anyone tell me whats going on here?

Quote
Originally posted by Confused_Bystander
I've got a very frusturating problem. I just bought the MSI 645 ultra mobo to upgrade my system, along with a brand new P4 2.0 GHZ processor and 512 mb DDR ram to go onto the board. My problem is as follows: The computer is not booting up. No OS, no BIOS, no nothing. When I turn the power on and hit the switch, all the hardware in the case starts up and sounds fine... but the screen remains blank. All four lights on the little diagnostic tool/usb port thingy that came with the board stay red, which, according to the manual, indicates a problem with the processor.
The processor is either bad (highly unlikely with it being an Intel chip) or for some reason its not working with the mobo. So, heres my question: Does an Intel P4 2.0 GHZ Northwood processor work with the MSI 645 Ultra?
Under the list of supported speeds, 2.0 ghz is not listed ?( . Can anyone tell me whats going on here?
ANy beep?

A free ebook for EJB 3.0 with the latest version of Netbean

Hi,
I am a trainee although with a good background in java.
I'm urgently in need of a free ebook for EJB 3.0 with the latest version of Netbean. Pls, help me with one if you have. my email is [email protected]
Again, is container managed bean good for a big project?
Thanks.
Emeka

emekaco wrote:
Hi,
I am a trainee although with a good background in java.
I'm urgently in need of a free ebook for EJB 3.0 with the latest version of Netbean. Pls, help me with one if you have. my email is [email protected]
http://www.theserverside.com/tt/books/wiley/masteringEJB3/index.tss
Here's a good free e-book but without Netbean. It covers everything you would need to know about EJBs.
>
Again, is container managed bean good for a big project?
The question is too vague to be answered. It's a design decision that needs more details.

After installing 1.5 with the msi, can I then zip it up and use it...

After installing 1.5 with the msi, can I then zip it up and use that version on another computer? I've done this successfully already for my needs etc. Just not sure if this was "kosher" etc.
I've installed Java JRE/JDK 1.5 using:
jdk-1_5_0_12-windows-i586-p.exe
I installed it on computer A at C:\jdk1.5.0_12. I then zipped it up and ran it successfully on computer B for my Tomcat service needs. It went seamlessly. However, did I over look any risks doing it this way. I did it this way because the MSI prompts a user for a install path. I need it for both the JRE/JDK to use C:\jdk1.5.0_12. Zipping up my installed version prevents that pesky user-error stuff/support tickets due to user error stuff.
Granted, I'd rather have users fill out a support ticket due to a typo then erroneously think I was successful at repackaging Java for our needs etc. Follow?
And therefore, was it ok to zip it up and port it?
Thanks a lot for your time and help. Truly appreciated!
Jeff

JyefuDCJS wrote:
After installing 1.5 with the msi, can I then zip it up and use that version on another computer? ...No. It will fail on Macs and Unix/Linux (don't know, don't care about other Windows boxes).
[Java Web Start|http://java.sun.com/javase/technologies/desktop/javawebstart/index.jsp] *(<- link)* is a better alternative for installing (and updating) Java apps. JWS works on all OS' for which there is a JRE.

Question to the forum My question really has to do with the replace stuff

Question to the forum
My question really has to do with the replace stuff from imovie 09
Ok when I pick up the stuff from the event library and pull up to the top it does not replace at play head or end or start
It mainly erases everything that is on there b4 so
So I am not sure
I actually also wanted to know what is the difference of just dragging to the end or end
And all these replacing options like replace at start end or replace alone for that matter ….

Hello again. Just to let you know I have solved the problem. Backed up my new phone. Then wiped all settings and everything off it to start again. When it relaunches it gives you the option to download from Icloud and you can pick from which back-up date you want to download it from. Picked the one from the day before it got trashed and HEY PRESTO, we have all the pictures and videos back!!! Iphone 0 - 1 Voodooboy78
I'm sure people will look at this and be like duhhhhhh but to me it is a VICTORY over technology!!! Peace

Imported RAW images badly corrupted, looks like red paint splashed all over the sky. Photoshop and Iphoto have no problem with the images from my D800E. Aperture worked fine for me in June with the same camera. The Nikon software shows no problem.

I am having a problem importing my images into Aperture 3 from my Nikon D800E. The images appear as if red paint was splashed across the sky. The Nikon software used to transfer from the camera does not show this problem and Photoshop 6 is fine with the images exported as jpg from the Nikon software. Aperature does not even like the jpg images usable by Photoshop. I am suspecting that Aperture is not correctly using the camera raw file. Also, the histograms are radically different between the corrupted images and the Photoshop (good) versions. Aperture worked just fine for me in June with the same camera. All drivers and software are current as of this posting. Anyone else out there seen this before??

Are you sure you do not have Highlight Hot & Cold Areas turned on? (View->Highlight Hot & Cold Areas)?
The bug in Digital Camera raw only affected Raw images. In your first post you wrote:
Aperature does not even like the jpg images usable by Photoshop
If the JPG's have the same problem then it isn't this bug.
regards

Are you aware of a possible bug in version 3.6.23? In the browser, for example, "two/" appears with the slash through the "o". Is this a known bug?

Are you aware of a possible bug in version 3.6.23? In the browser, for example, "two/" appears with the slash through the "o". Is this a known bug?
When the same text is view in another browsers it appears correctly as "two/".
I've checked, and the same problem appears in Firefox on another computer.
The two answers received so far have not provided an answer: is this a known bug in Firefox?
Thank you.

You are on a Mac and that is a [http://en.wikipedia.org/wiki/Kerning kerning] problem. Don't you see the same problem in other applications if you choose the same font, font-weight and font-size.
I only find one other kerning [https://support.mozilla.com/questions/789254 question] here -- it is marked unsolved. I find it strange that Firefox got involved with this at all rather than leaving such things to the operating system and font metrics.
Does the problem go away with "command+0" (zero) which resets [http://kb.mozillazine.org/Zoom_text_of_web_pages zoom level] to normal. If you mess with the font sizes in your preferences because you want larger print that would have the same effect.
Also found this one recently reported for [https://support.mozilla.com/questions/892222 Firefox 7 in ubuntu 11.04] which appears much worse. If it involves Firefox and specific operating systems it becomes a lot harder to diagnose who or what is responsible.

Need help from somebody with the "MSI KT6 Delta-FIS2R" motherboard

Hi everybody!
I really need some help from somebody with the MSI KT6 Delta-FIS2R motherboard (the one with onboard LAN, Audio, RAID, S-ATA and IEEE1394 firewire). You see. I've got this board myself but it's been destroyd. Some values for the onboard devices in my board has been overwritten so that windows no longer recognizes the onboard LAN and Audio controller anymore. I really need some help from somebody with this board.
I need to see what the values for the onboard devices should be. I hope someone can help me by sending me a repport from the Everest home edition: http://www.lavalys.com/products/overview.php?pid=1&lang=en
If anyone could do me this favour, I would be VERRY thankfull

Quote from: HYSTERIAH on 12-November-05, 06:24:20
I really need some help from somebody with the MSI KT6 Delta-FIS2R motherboard
HYSTERIAH,
With 76 Replies and 277 Views on your original thread, it looks to me like people have been trying to help you.
So there is no confusion, I am locking this thread so all your help and advice you receive will be in the same place, so people do not need to jump between threads to keep track of what has already been suggested for this mobo of yours.
Richard

How to get the text field in the header for only first page of the report

Hi,
I am developing reports in BI Publisher Enterprise where i am facing problem i.e., i have to get some text field in header,for only first page in the result but it is displaying in all the other pages of the report in result.So,please if you have any idea of how to solve it, please reply.It is required as early as possible.
Thanks in Advance

Invalid path? What are you doing? Writing the report output to an invalid directory?
Where are your terms and conditions? It would be very easy just to put them in a database table and select them in your report query.

I hope someone gets this who can help me. i don't find anything helpful in the help section of icloud. i'm using my 4th generation itouch for about 3 weeks with the ical. but today when i tried to edit an event or d an event a window would pop up and sa

i hope someone gets this who can help me. i don't find anything helpful in the help section of icloud. i'm using my 4th generation itouch for about 3 weeks with the ical. but today when i tried to edit an event or add an event a window would pop up and say "event can't be saved" or "no calendar chosen" or something like "this event doesn't belong with this calendar" and stuff like that.
can you please help me fix this?

You could repartition your drive to have a different OS X with the older iTunes there, and the newer iTunes on the existing partition. Back up everything beforehand. See Kappy's advice in this thread. Partitioning my Hard Drive

None of the fact sources for [column] are compatible with the detail filter

Hi Experts,
I am using obiee 11.1.1.7.
Getting below error when i add a filter of non conformed dimension column.
Below is the error
Error Details
Error Codes: OPR4ONWY:U9IM8TAC:OI2DL65P
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 43113] Message returned from OBIS. [nQSError: 43119] Query Failed: [nQSError: 14023] None of the fact sources for [column] are compatible with the detail filter
Please help in solving an issue.
Regards,
NN

Hi NN
You need to follow steps in below link to model your BMM layer for the report to work with non confirmed dimensions.
http://obibb.wordpress.com/2010/05/31/multiple-fact-reporting-on-non-conforming-dimensions/
Once you have followed these steps you can use the non confirmed dimension in the reports.When you see the logs to see the query generated by obiee,it generated 2 queries 1 with confirmed dimension and other with non conformed dimension.When you filter using non confirmed dimension you will now not notice any error but the results will not be filtering out because the filter will be applied only in 1 query which is valid
Now for this to work what you can do is ,instead of using the filter drag the column you like to filter as a prompt in your view.default it to the value you need using the case statement and hide it.This is one of the work around.
There may be many other work arounds for this but you need to understand that for you requirment to work you need to tweek OBIEE to generate 1 query instead of 2 queries.

Questions for my first pc with the msi neo2 fr motherboard

Similar Messages

Maybe you are looking for