Quicktime doesn't run smoothly the FullHD MP4 Videos

I have videos MP4 made with a phone FullHD 1080P that plays perfect in my MacBook Air is I use VLC or MplayerX but if I use Quicktime then doesn’t play smoothly they stop for seconds each few seconds, I have same issue If I play the videos in IPhoto that I suppose are related,
Is there a way to upgrade or get a codec for QuickTime to resolve this issue?

Yes it is a Facebook server problem.

Similar Messages

  • Crystal Report doesn't run on the production PC

    I developed a report using VS 2005/Crystal Report. The report has three on-demand sub reports and some subreports. It runs well on my PC, but doesn't run on the production PC, on that PC, I only can see the report header or few columns. The difference (I can tell) between my PC and the production PC is my PC has VS 2005 installed.
    Is there anything I can do to make the report running on the production PC?
    Thanks.

    Hi Jhon,
    Have you installed the runtimes of CR of VS2005 on your server, if not than please install from(only applicable if you are using the bundle version of CR i.e. CR 10.2 which comes with VS 2005) [here|http://resources.businessobjects.com/support/additional_downloads/runtime.asp#07].
    Note- use the appropriate version of merge modules for 64 or 32 bit machine
    hope this works
    Regards,
    Amit

  • Can't play the embedded mp4 video in SWF

    Hi, I am creating a basic webpage for the first time. I have successfully inserted a SWF flash player in Dreamweaver, however I am unable to play a mp4 video that is embedded in my swf flashplayer within Dreamweaver web page.
    Message was edited by: Madalsa Tested and previewed the exported SWF on stand alone basis, there I am able to play the embedded mp4 video.  Any ideas will be appreciated.

    I don't mean to impose or anything, but I'm in dire need of help. I've been trying to understand your directions, but to no avail.
    I'm trying to get my embedded .mp4 video to play in my .sfw video on my webpage...  I know that  you said that firefox won't play .mp4 vidoes, and recommend converting it into a ogg.
    The thing confusing me is that... I'm not sure which file I should be converting here... Infact I did convert the .mp4 into a ogg well actually it's a .ogv(confused here also), but am i suppose to convert the .sfw file as well? And how would I setup it up in your first example(i ask this question again below)
    The .mp4 file was 20131122_123440.mp4 , now it's 20131122_123440.ogv and the .swf file is secondtime.swf
    This is the coding I have below set up for my website:
    <!doctype html>
    <html>
    <head>
    <meta charset="utf-8">
    <title>Untitled Document</title>
    </head>
    <body  bgcolor="blue">
    <table width="1001" height="420" align="center">
    <tr>
    <td></br>
    <p align="center">
    <object classid="clsid:d27cdb6e-ae6d-11cf-96b8-444553540000" codebase="http://fpdownload.macromedia.com/pub/shockwave/cabs/flash/swflash.cab#version=7,0,0,0" name="0" width=1000 height=420 align="middle" id=0>
    <param name="movie" value="secondtime.swf" />
    <param name="menu" value="false" />
    <param name="quality" value="high" />
    <param name="bgcolor" value="#FFFFFF" />
    <embed src="secondtime.swf" menu="false" quality="high" bgcolor="#FFFFFF" width=1000 height=420 name="0" align="middle" allowScriptAccess="sameDomain" type="application/x-shockwave-flash" pluginspage="http://www.macromedia.com/go/getflashplayer" />
    </object>
    </td>
    </tr>
    </table>
    </body>
    </html>
    Now if I was to simply to put it in this example below:
    <video controls>
      <source src="foo.mp4" type="video/mp4">
      <source src="foo.ogg" type="video/ogg">
      Your browser does not support the <code>video</code> element.
    </video>
    How would I be able to get it to work?
    Also, I've read that it could be a pathing issue as well.... Because when I run the video as a test from my computer into firefox it plays the flvplayback (which was the .mp4, and maybe I should of mentioned this in the beginning?), and it works fine.. I placed the .html and the .sfw and the .mp4 in the same folder to try to get it to work, but it doesn't work online, and  I noticed that once I put the .mp4 back on my desktop it plays the video fine in the test run fine... Maybe I should put the .ogv file into the folder instead? I don't even know how that would work.
    Thank you for taking your time out to read this, I really apprecaite it!!! Sorry for the lack of understanding as well!

  • My ipod touch 4th Gen doesn't show me the music and videos

    My ipod touch 4th Gen doesn't show me the music and videos I have, even though I can see it all in the I tunes and I can see that the ipod memory is full as it was... What to do???
    Thx

    Not compatible.
    All the iOS devices compatible (iPhone 4 and later, iPad 2 and later, and 5G iPod touch) with iOS 7 have at least 512 MB of memory. The 4G only has 256 MB

  • TI SmartView doesn't run since the last Mac OS X update

    Hi everybody,
    I currently use TI SmartView (Interactiv Emulator for TI Calcs) with my pupils. Since the last update of Mac OS X (my macbook runs with 10.6.5 version), TI SmartView doesn't run and I have the following message which appears:
    +Process: JavaApplicationStub [1208]+
    +Path: /Applications/TI-SmartView83Plus.fr84Plus.App/Contents/MacOS/JavaApplicationStub+
    +Identifier: com.apple.javajdk16.TI-SmartView pour TI-83 Plus.fr / TI-84 Plus+
    +Version: 1.0 (1.0)+
    +Code Type: X86 (Native)+
    +Parent Process: launchd [172]+
    Do you know what is this problem ? Is it a problem with Java ?
    Many thanks for your answers !
    Friendly yours,
    David

    - I also tried to reinstall this software, without any success.
    - TI contacted me and gave me a web link to download TI SmartView 1.1 ... I've done this, installed it ... and the same problem is always here ! :-((
    I think that this problem probably comes from Java.
    Here is the beggining of the error report:
    +Process: JavaApplicationStub [4114]+
    +Path: /Applications/TI-SmartView83Plus.fr84Plus.app/Contents/MacOS/JavaApplicationStub+
    +Identifier: com.apple.javajdk16.TI-SmartView pour TI-83 Plus.fr / TI-84 Plus+
    +Version: 1.1.0 (1.1.0)+
    +Code Type: X86 (Native)+
    +Parent Process: launchd [185]+
    +Date/Time: 2010-11-16 19:56:16.147 0100
    +OS Version: Mac OS X 10.6.5 (10H574)+
    +Report Version: 6+
    +Interval Since Last Report: 93556 sec+
    +Crashes Since Last Report: 27+
    +Per-App Interval Since Last Report: 89 sec+
    +Per-App Crashes Since Last Report: 9+
    +Anonymous UUID: 7B1EBE0A-09F1-47A9-8160-D8EE63F71569+
    +Exception Type: EXCBADACCESS (SIGBUS)+
    +Exception Codes: KERNPROTECTIONFAILURE at 0x0000000000000010+
    +Crashed Thread: 20 Java: Thread-2+
    +Application Specific Information:+
    +Java information:+
    +Exception type: Bus Error (0xa) at pc=00000000250ce4aa+
    +Java VM: Java HotSpot(TM) Client VM (17.1-b03-307 mixed mode macosx-x86)+
    Does it help someone to solve the problem ??

  • Attribute change run process doesn't run in the chain

    Hello everyone,
    I have implemented a process chain with multiple parallel processes (12, like the batch processes in the application server) and I have put for each stream a loading of master data followed by the attribute change run process. When I run my chain then I find that one o two Attribute change run process doesn't run (the InfoObject chosen seem to be random!). The chain remain in yellow color. Can you help me anyone about this question?
    Regards,
    Francesco

    Couple of thing you should keep in mind while loading master data.
    if two loads are targeted to the same infoobject they will collide and as a result the later load will fail.
    it is a good practice to use only one Attribute change run in the end before you load master data. but if there are dependecies you can use several in series
    Also when you set up Attribute change run make sure that Attribute change run will pickup only the particualr infoobject not all the objects in the Attribute change run list.

  • SCXI 1112 and 1302 doesn't run at the same time

    Hi,
    I have SCXI 1112 thermocouple input module,  SCXI 1180 feedthrough panel , and a SCXI 1302 terminal block connected SCXI 1000 chassis with SCXI 1349 adapter. I am trying to measure voltage by using SCXI 1180&1302, and temperature by 1112 module at the same time. When  chassis is on SCXI 1112 runs without a problem; however, voltage reading coming through SCXI 1349 makes no sense (plus I can't run them at the same time, LAbview gives an error). While the chassis' power is off, it is the other way around, SCXI 1349 runs smoothly.
    In addition to that, a radiometer, connected to a power supply, is wired to SCXI 1302 terminal block. When power supply is on, SCXI 1112 module's temperature reading is 4 times higher than actual value. In other words, power supply effects the readings.
    Could you please give me some advice to solve this problem?
    Thanks,
    Azra

    One piece of the puzzle you left out is the DAQ card being used in the host computer. 
    Without looking at some specifics on the SCXI cards/connectors you are using, I will comment you must be careful when you are using an 1180 feedthrough module.  Keep in mind, the SCXI chassis is Signal Conditioning -- it's nothing without the DAQ. 
    I would recommend you back up a few steps, simplify the setup and test each input channel from MAX -- making sure you aren't overlapping channels between the 1180 to the DAQ and the SCXI chassis.  Remember, most data from the SCXI chassis comes in on a single channel of the DAQ through the 1349.
    Hope this might help. 
    RS

  • Quicktime doesn't run - Illegal Plugin Error

    I recently purchased this computer, and used "PC Mover" to move my settings from an older PC to this one. I think I have conflicting versions of QuickTime, because I can't uninstall it - I'm getting a "Fatal Error during Installation" error when I try to uninstall. When I try to re-install, Quicktime doesn't work at all.
    I'm just trying to get to a point where I can view mpg's from a website. Whenever I try to do this, I get a "Quicktime plugin error 7.1.3" - Plugin performed an illegal operation. You are strongly advised to restart Navigator" (Even though I use Mozilla Firefox, I get similar errors in IE, so I don't think it's a browser issue).
    Any help I could get on this would be greatly appreciated.
    Thanx,
    Tony_Van

    I was able to get help from the Apple support people.

  • Preferences form doesn't run on the web

    Using form qms0006f 'User preferences' on the web gives FRM-40735 - On ERROR trigger veroorzaakte onverwerkte exception ORA-06508.
    Using the same form client server against the same database works fine.
    Is this a known problem?
    null

    I am getting this problem when I run Demo and Application Foundation.
    I am running under NT.
    Can you tell me how you solved this issue?
    <BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by Willem Laan ([email protected]):
    Thanx for your reply.
    The form always runs in the same operating system. So I don't have any 'UNIX to NT' or viceversa problems.<HR></BLOCKQUOTE>
    null

  • HT204382 if i buy guick time X i will be able to run all the formats of videos

    if i buy guick time X i will be able to run all the formats of videos

    There is no QuickTime X for Windows, and QuickTime Pro will not play any file that the free QuickTime Player won't.
    (76415)

  • GarageBand running in the background with video app open

    I was wondering if GarageBand will run in the background while I'm using the video app on the iPad. Basically, I'm looking to have my guitar running into my iPad with GarageBand running, while watching/following along with a guitar video lesson I also have on my iPad. Can the two programs run simultaneously, or will the video app eliminate the sounds I would get from GarageBand? Thanks.

    Yes, I've done that while playing youtube videos with the youtube app (I'm still using ios 5.1).
    Just go the wrench icon in Garageband and turn on "Run in Background".

  • Flip video starts, stops, doesn't run smoothly

    I have a Powerbook G4, 1.67 GHz, 10.4.11 with Quicktime 7.6. I downloaded the video from my Flip Ultra and it barely runs in Quicktime - stutters, starts stops, video lags behind audio. I downloaded the 3ivx and the Perian software and still no luck. I did import the video into iMovie HD and it works fine there. Any ideas?

    Is it one of the new Flip Ultra HD cameras that came out last month? Or is a standard definition Flip Ultra? If it's one of the new Flip Ultra HD camera your computer is under powered to playback the video in Quicktime.
    For 1280x720 (720p) video at 24-30 frames per second:
    (Macintosh)
    1.8 GHz PowerMac G5 or 1.83 GHz Intel Core Duo or faster Macintosh computer
    The Flip HD cameras uses 3ivx to encode the video to h.264. Not one of the best encoders. I have one of the flip's Mino HD camera and I have to transcode the video into another codec so I can play the video one my computer.

  • I'm running Flash 10.2 on an HP Mini 311-1000NR, but Hulu stutters on 480P. Tried taking off Hardware Acceleration and it doesn't run smoother. Do I need to re-install Flash 10.1 beta? And how do I do re-install an older version of Flash?

    Running Windows XP, upgraded ION LE drivers to the latest drivers.

    "2MEM/1/4: DIMM3/J14"
    Replace the memory in the DIMM 3 slot.
    If you are running Mac OS X 10.5 you can use this program to test your G5's memory:
    http://www.kelleycomputing.net/Rember/
    It will subject your RAM to a more thorough test than Apple Hardware Test.

  • One of my dll's in my vi doesn't run with the error "application configuration is incorrect"

    I just installed LV2011 and one dll from my vi won't load with the error "application configuration is incorrect", which is Windows lingo for "missing package dependencies".  All the computers at my company with 2010 loaded seem to do OK.  When I do a Dependencies Walk I get missing Visual C debug dll's missing plus IEshims and wer which both have a whole tree of dependencies missing on my machine.  The Windows install is the same "Windows XP version 2002 Service Pack 3"  So I'm thinking I have to uninstall 2011 and go back to 2010.  Is this correct?  Those VC debug dll's were installed on the machines with 2010 in them but were not installed in mine.
    Thanks in advance.

    Hm,
    it seems that you might have more success in the LabVIEW forum here; this one is for LabWindows/CVI...

  • Quicktime 7.7.4 will not play mp4 video

    I have several recorded videos saved in mp4 format that will not open in Quicktime. The audio plays, but the video is only a black screen. I have one mp4 file that I recorded a few days before the others that will open in Quicktime. All the files open in VLC, DivX, Adobe Premiere Pro 5.5, and Windows Media Player. I am using Windows 7 and I need to import these videos into Photoshop CS5.5 extended which it will not do if the files won't play in Quicktime. I've tried just about everything including re-recording, but my recording will only save in mp4 or flv. I have also uninstalled and re-installed quicktime, photoshop, and my recording device.
    The first two images are from files that will not play in Quicktime, no picture only sound. That last image is from a file which will play; both sound and picture.

    I have several recorded videos saved in mp4 format that will not open in Quicktime. The audio plays, but the video is only a black screen. I have one mp4 file that I recorded a few days before the others that will open in Quicktime. All the files open in VLC, DivX, Adobe Premiere Pro 5.5, and Windows Media Player. I am using Windows 7 and I need to import these videos into Photoshop CS5.5 extended which it will not do if the files won't play in Quicktime. I've tried just about everything including re-recording, but my recording will only save in mp4 or flv. I have also uninstalled and re-installed quicktime, photoshop, and my recording device.
    The first two images are from files that will not play in Quicktime, no picture only sound. That last image is from a file which will play; both sound and picture.
    Your video data rates are virtually nonexistent. (I.e., a "normal" quality AAC stereo track for a video file is typically recorded with a sampling rate in the 44.1 KHz at 128 Kbps to 48 KHz at 160 Kbps range.) As you can see in the inspector images the total audio plus video data rate allocated for your files are all little more than that required to support a "normal" stereo audio track. Recompress the files using a more realistic video data rate. Try something in 1.25 Mbps to 2.50 Mbps range as a starting point and determine the minimum level of quality you can live with here. (I.e., a typical VGA SD iPod file is normally compressed with a video data rate on the order of 1.5 Mbps to 1.7 Mbps.)

Maybe you are looking for