RE1000 - Initial setup did not work

73 minutes on the phone. According to the tech rep, we had exhausted all potential solutions. I purchased this becuase it was sleek, small, and appeared simple to install. I am not a tech dummy, but this thing was a brain-buster! I have an Xfinity wireless gateway made by SMC Networks. I have only Apple devices. One iMac, 3 iPhones, and one iPad. should be about as simple and streamlined of a setup as this product could possible face. And yet, it failed miserably! Frustrating experience to say the least. As mad as I am at Cisco for selling a product that fails in such a simple application, I'm ten times more angry with Xfinity - if their modem wasn't such a POS, I wouldn't have to spent nearly $100 to improve the signal!

The Linksys Wireless Range Extender and wireless router or access point’s wireless settings should match in order for them to work properly. You must first identify the following wireless settings of your router:
• Wireless Network Name (SSID)
• Wireless Channel
• Wireless Security Mode (WPA/WPA2 Personal or WEP)
• Network Key or Passphrase
Here is the link for the configuration of the RE1000…
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=206954591ff54e36884bb4636fcfd3d9_Manually_configur...
Lastly and most importantly, remember that in order to get the best performance from an RE1000 you need to place the extender in an area where you still have at least 50% signal strength to your router when you place it in the final location where the RE1000 will be used. To configure the RE1000 you will need to login to the UI after you have put the RE1000 in the final location to verify the signal strength below is a reminder about signal bars and what they mean as a reminder
For ALL configurations you should have between 2-3 bars of signal at the very least. If you have less we will need to move the RE1000 closer to the router. You can also check the status on the status page of the RE1000 as well. On the status page it measures both Signal Strength and Signal Quality. If either set of bars is red you must move the RE1000 closer to the Router.

Similar Messages

Adobe setup did not worked

Hello,
Every time i try to install the last patch for photoshop cs4 11.0.2 (windows vista 32) I am always having a "Adobe setup did not worked".
The same problem happened for InDesign (6.0.() and After Effects (patch 9.0.3).
It's really driving me crazy.
Anyone can help me ?
JJ

Nothing you can do short of a full reinstall of all CS4. Your caps.db got locked due to a flakey update of another app and market some files as non-replacable, thus the updater fails. Read this and this, if you feel like reinstalling...
Mylenium

When I started my PC this morning I got a pop-up message stating that CC has damaged files and required downloading. Indeed, CC did NOT work and subsequent attempts to download CC never got beyond the initial installer box. I am at my wits end here. Have

When I started my PC this morning I got a pop-up message stating that CC has damaged files and required downloading from www.adobe.com/go/adobecreativecloudapp. Indeed, CC did NOT work and subsequent attempts to download CC never got beyond the initial installer box. The posted link also appears to be bogus I am at my wits end here. Have other users experiences this issue? Is this a clever intrusion?

Please ensure you have the latest version of the Creative Cloud app installed
http://helpx.adobe.com/creative-cloud/release-note/cc-release-notes.html
We also have this solution for the having to sign in on every product launch
http://helpx.adobe.com/creative-cloud/kb/unable-login-creative-cloud-248.html
You can also try uninstalling & re-installing the CC.
Regards
Rajshree

ITunes 10.5 Upgrade fails to Install. The Error Message is: "There is a Problem with this Windows Installer Package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor."

When Upgrading on my laptop from iTunes 10.2.11 to 10.5.0 the message I get is: "There is a problem with this Windows Installer Package. Aprogram run as part of the setup did not finish as expected. Contact your support personnel or pacakge vendor.

After reading all these posts, one by one did not resolve my problem until I got the very end. Regardless of what step would resolve your problem, these are the steps I would recomment to everyone for a what seems to be a safe and fool-proof upgrade to iTunes 10.5.
1. Stand alone upgrade to the latest Quicktime version
2. Go to control panel and "change" then select repair to the following applications in the order specified by the post on Oct 27. (Notice I skipped Quicktime because it had been upgrade manually,and Bonjour did not have a "repair" option)
iTunes; Apple Software Update: Mobile Device Support; Apple Applications Support
Some of these applications may not appear if they do not apply to your configuration (no iPhone, or no iPad, or other apple devices).
Once all updated, I did not need to restart nor launch any applications, I simply went straight into the 10.5 upgrade, and where it normally got stuck, this time the installation continued for a while longer until it completed successfully.
Great work everyone who contributed! Thank you very much!

When I try to install iTunes 10.5, it says, "There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor." I have Windows XP and I need help.

5, it says, "There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor." I have Windows XP and I need help.

After reading all these posts, one by one did not resolve my problem until I got the very end. Regardless of what step would resolve your problem, these are the steps I would recomment to everyone for a what seems to be a safe and fool-proof upgrade to iTunes 10.5.
1. Stand alone upgrade to the latest Quicktime version
2. Go to control panel and "change" then select repair to the following applications in the order specified by the post on Oct 27. (Notice I skipped Quicktime because it had been upgrade manually,and Bonjour did not have a "repair" option)
iTunes; Apple Software Update: Mobile Device Support; Apple Applications Support
Some of these applications may not appear if they do not apply to your configuration (no iPhone, or no iPad, or other apple devices).
Once all updated, I did not need to restart nor launch any applications, I simply went straight into the 10.5 upgrade, and where it normally got stuck, this time the installation continued for a while longer until it completed successfully.
Great work everyone who contributed! Thank you very much!

Error when downloading itunes 10.5 that says Product: Apple Software Update -- Error 1722. There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package ven

Each time I attempt to download the new itunes 10.5 I keep getting the following error message:
Product: Apple Software Update -- Error 1722. There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor. Action SoftwareUpdate_UnregServer, location: C:\Program Files\Apple Software Update\SoftwareUpdate.exe, command: /UnregServer
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp.
Any Ideas of how to solve this one?

After reading all these posts, one by one did not resolve my problem until I got the very end. Regardless of what step would resolve your problem, these are the steps I would recomment to everyone for a what seems to be a safe and fool-proof upgrade to iTunes 10.5.
1. Stand alone upgrade to the latest Quicktime version
2. Go to control panel and "change" then select repair to the following applications in the order specified by the post on Oct 27. (Notice I skipped Quicktime because it had been upgrade manually,and Bonjour did not have a "repair" option)
iTunes; Apple Software Update: Mobile Device Support; Apple Applications Support
Some of these applications may not appear if they do not apply to your configuration (no iPhone, or no iPad, or other apple devices).
Once all updated, I did not need to restart nor launch any applications, I simply went straight into the 10.5 upgrade, and where it normally got stuck, this time the installation continued for a while longer until it completed successfully.
Great work everyone who contributed! Thank you very much!

Im trying to download itunes 10.5 but keep getting error message that says: There is a problem with this Windows Installer package. A problem run as part of the setup did not finish as expected. Contact your support personnel or package vendor.

im trying to download itunes 10.5 but keep getting error message that says: There is a problem with this Windows Installer package. A problem run as part of the setup did not finish as expected. Contact your support personnel or package vendor. I am using windows XP 32 bit, all the other computers in my house downloaded just fine, no problems, however this is the computer my iphone is set up to, ive tried doing a virus scan, windows update, downloading other things, updating everything possible, everything works fine, its just itunes that wont download, anyone have any other ideas?

Yes, I had found a similar solution also. I'm running XP Pro, SP3. I went Control Panels/ Add-Remove programmes/apple software update/ change/ repair. Then run the 10.5 exe.
While the programme updated from version 8 of iTunes, my new iTunes is now a mess. Not all of my music was in the same folder previously but it all showed up on iTunes. Now many albums have been left out, some have only a few tracks and some have two copies of some tracks as well as having other tracks missing. I haven't begun to work on that.

I keep geting this message when trying to udate to Itunes 10.5.1 "There is a problem with the Windows Installer package. A program run as part odf the setup did not finish as expected . Contact your support prersonel or package vender"

I keep getting this message when trying to upgrade to Itunes 10.5.1
Driving me nuts trying to upgrade. What can I do to correct this?
"There is a problem with the Windows Installer package.
A program run as part odf the setup did not finish as expected .
Contact your support prersonel or package vender"

Yes, I had found a similar solution also. I'm running XP Pro, SP3. I went Control Panels/ Add-Remove programmes/apple software update/ change/ repair. Then run the 10.5 exe.
While the programme updated from version 8 of iTunes, my new iTunes is now a mess. Not all of my music was in the same folder previously but it all showed up on iTunes. Now many albums have been left out, some have only a few tracks and some have two copies of some tracks as well as having other tracks missing. I haven't begun to work on that.

Recovery did not work with new hard drive

The original Toshiba HD(250G, sata1) of my laptop( ) crashed.
I bought new one (320G, sata 2, Western digit )
The problem is that, when I tried to use the recovery CD that I used to use it with old HD before, it did not work with this new HD well!?
After cd1 and cd2 finish installing it ask to take it out then restart, I do so, but when it comes to setup setting of windows.
An error message come out says " Windows Setup could not configure Windows on this computer’s hardware”
It restart and says again " Windows could not complete the installation. To install Windows on theis compuiter, restart the installation."
I have been trying to solve this a lot, but no way
I tried what in this link, but it drive me with another problem http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_install/windows-could-not-complet...
I hope that I get the right thing to do, from ur forum by this post.
Thanks a lot

Did you folks search here for "advanced format drive"? People have had numerous weird problems with the new advanced format hard drives in older Toshibas. I can't look up all the threads for you. But here is one:
http://forums.toshiba.com/t5/System-Recovery-and-Recovery/Recovery-won-t-work-on-new-upgraded-hardri...

When installing itunes 10 uding windows xp I get the following error: "There is a problem with this Windows Installerpackage. A program run as part of the setup did not finish as expected. Contact your sipport personnel or package vendor." - any ideas?

When downloading itunes 10 in windows xp, I get the following error "There is a problem with this Windoes Installer package. Aprogram run as part of the setup did not finish as expected. Contact your support personnel or package vendor." - any ideas on how to proceed?

using MSICUU2.exe didn't help me. But, the new replacement app did:
http://support.microsoft.com/mats/Program_Install_and_Uninstall
I fixed my problem like this:
Here's the deal -
1. can you install itunes via the APPLE SOFTWARE updater?
I couldn't so I downloaded ITUNES and tried to install it that way.   Hence I got the same error hang as you. Nothing worked, (Multiple attempts at uninstall reinstall, stopping of Services, Reg cleaners etc..)
2. If answer is NO to #1 you must fixe the APPLE SOFTWARE UPDATE Program.
OK so I couldn't find a Download for this.   But: if you have WINRAR, open the ITUNES.EXE and extract the APPLESOFTWAREUPDATE.MSI file. Execute the APPLESOFTWAREUPDATE.MSI separately.   And you will not be able to install it and have a similar issue as per your Itunes install.   This of course leads you to believe that the Itunes.exe install is also installing all of these components including the applesoftwareupdate silently.   It must BOMB at that portion of the install and you are done.
3. Your goal now is to get the applesoftwareupdate installed.   How do you do this. Well - here is what I did.
a. downloaded and RUN a PC Installer FIX it tool from Microsoft. This is a replacement for the older MSI fixer they used to use.
http://support.microsoft.com/mats/Program_Install_and_Uninstall
b. It will list programs to attempt to fix.
choose AppleSoftwareUpdate.msi
c. Once it is done, then reinstall apple program updater using
AppleSoftwareUpdate.msi
Finally it should install since the Microsoft tool appraently fixed corrupted installation files in your registry for this application.
(Please note: that I also disabled any apple related services such as BONJOUR or IPOD DEvice RUN: services.msc to get there - although this man not be necesarry.)
Hence Launch this APPLE UPDATE SOFTWARE (Click the ICON in your Start menu) it should list ITUNES
select ITUNES from here and it will update.
KEY HERE is to ONLY UPDATE APPLE Stuff via the APPLE SOFTWARE UPDATE program. If that program is not working fix it. Then Bingo.
I am sorry to see folks having this problem for weeks.
APPLE,   Spread the word. PC's can get corruption in the registry on your product should the update be stopped or computer shut off during an update. etc...   Please improve your software updater program to check for invalid registry upon launching the app. This will prevent people thinking it is an APPLE issue. It appears to be a problem on your PC's registry settings for the APPLE Software update.
Bruno Ricci

Office Jet Pro 8600 Plus Scan to Email Setup, website not working.

When setting up scan to email.
The first question is: Is the HP software provided with the printer installed on the network-connected computer?
The answer should be yes, but we can't follow the steps of opening up the software on the computer and acessing scanner options like the printer tells us to.
Anyway, in the past I have set up a two users by selecting "No" to this question then it provies me with a website to enter in:
http://192.168.5.158
This is the current address it is giving me. This has worked for me in the past and have had no issues setting it up this way. But now (after my employer changed my email address) my scan to email is no longer working and I am trying to set it up again with my new email.
Every time I type in the given address: http//192.168.5.158 I receive an error message.
[Fiddler] The socket connection to 192.168.5.158 failed.
ErrorCode: 10060.
A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond 192.168.5.158:80
I had found a forum that had supposedly been a solution where they said to remove web services on the printer and re-set it up, this did not work at all. Still can't set up a scan to email. I just want to use the site given like I normally do, and set it up that way, I need help as SOON as possible please

Hello rachelhuver,
Welcome to the HP Support Forums!
Regarding the issue connecting to the Officejet Pro 8600 Plus's Embedded Web Server to change the Email used for Scan to Email, I would like to see if I can help.
If you touch the Wireless icon on the printer, is the I.P address the same as you noted in your post? If not, use that I.P in an attempt to access the needed page.
If you are still unable to load the page, try using a different web browser on the computer. For example, if using IE, try Firefox.
If you are still unable, it would appear to me that the network is blocking this page from you. You can get around this by connecting temporarily to the printers Wireless Direct network. To connect to this;
Touch Setup
Network
Wireless Direct
On with no security (I suggest)
Connect the computer to the printer's network, ie HP-Print-**-Officejet 8600 series.
Open a web browser (don't worry if you get a message about no Internet), enter this I.P: 192.168.223.1 and hit Enter.
You should now be able to access the Embedded Web Server of the printer, make your changes and apply them.
Hope this helps,
JERENDS
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

When I try to install icloud on my laptop running windows 7 home premieum I get message saying the windows installer package wont complete as a program run as part of setup did not finish as expected the install then rolls back I have tried rein

when I try to install icloud on my laptop running windows 7 home premieum I get message saying the windows installer package wont complete as a program run as part of setup did not finish as expected the install then rolls back I have tried reinstall deleting files signing on with another account etc nothing works I have read this is an apple programing problem if so is there a fix I need iclouds thanks

This other discussion may help: Re: how do I install icloud

Appletv 2 flashing quickly - no reponse at all -tried to unplug power but did not work.

Appletv 2 flashing quickly - no reponse at all -tried to unplug power but did not work. What should i do?

You'll have to connect the your ATV2 to computer via micro-usb port on the back. Open itunes and put the ATV2 in DFU mode by holding down the menu and play button for 7 seconds. Itunes should recognize the device. Once it does press the restore button,itunes will then download the latest software and reinstall it on the ATV2. You will then have to go through the setup process again. If that doesn't fix the problem take it back the store you bought it at.

Therer is a problem with this windows installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor. This is on Windows 7. Is there an easy fix?

When trying to install an itune upgrade on a Windows 7 machine I get the following message: There is a problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor. One solution I found by googling is to go to Control panel/add/remove programs and REPAIRING THE APPLE SOFTWARE UPDATE. Don't seem to work for me tho......any solutions? Thanks

I finally found a reply that said to go to the Apple Installer and repair and it seems to have worked! I was looking for a Windows installer all the time. Thanks to whoever put that fix out there.

"Setup did not detect the required components. Setup will exit." !?!?!?

I have a retail Audigy 2. Autoupdate recognizes my card and gives me the available list of drivers and applications for download. I download the following:
) Audigy 2 Drivers
2) Audio Console
3) EAX Console
4) Speaker Settings
5) Surround Mixer
The ) Drivers and the 2) Audio console installs just fine. However, for each of the three remaining programs (3, 4, & 5 listed above) upon executing the downloaded file they all give me a pop-up window that says:
?Setup did not detect the required components. Setup will exit.
This happens with all three of them. I want to install these because I am of the understanding that one of these contains the ?Speaker channel test? (for lack of a better word) that will test if my speakers are hooked up correctly to the right channels. The ) drivers, and 2) Audio console do not have that test. I created another post concerning this but nobody has replied:
http://forums.creative.com/creativelabs/board/message?board.id=soundblaster&message.id=39825
I also tried unzipping the three executable files with WinRAR, and then executing the Setup.exe files but it yields the same results.
Anyone know why I can't install these applications?!?!?!?!
I swear, I have never had so many problems with a particular brand of product than I have with Creative products?.yet I keep buying them anyway?.sheesh?.Message Edited by Bridgeboy on -30-2005 05:0 PM

nanite2000 wrote:
superidan wrote:
I have retail Audigy 2 card. tryed removing the card and installing on a differant slot. Nothing Works! it produces the same "no audigy 2 card found - setuip will now exit" Creative sould be ashamed thanks
Yes, Creative should be ashamed.
This is a known problem that has been around for months and they have failed to address, just like many other problems with their soundcards. For the solution to this particular problem, look here:
http://forums.creative.com/creativel....id=3964#M3964
If you would reread my original post in this thread, that solution did not work for this particular problem of mine. I have a SoundBlaster Li've! Card that this solution worked for, however it does not work of the Audigy 2 card?unzipping the files with WinRar and then running the Setup.exe files produces the same result?setup does not recognize the required components and will close.
I?m not saying that the person who you quoted should not try it though.

RE1000 - Initial setup did not work

Similar Messages

Maybe you are looking for